| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * (C) Copyright 2018 Xilinx |
| * |
| * Xilinx ZynqMP Generic Quad-SPI(QSPI) controller driver(master mode only) |
| */ |
| |
| #include <common.h> |
| #include <cpu_func.h> |
| #include <asm/arch/sys_proto.h> |
| #include <asm/io.h> |
| #include <clk.h> |
| #include <dm.h> |
| #include <malloc.h> |
| #include <memalign.h> |
| #include <spi.h> |
| #include <ubi_uboot.h> |
| #include <wait_bit.h> |
| |
| #define GQSPI_GFIFO_STRT_MODE_MASK BIT(29) |
| #define GQSPI_CONFIG_MODE_EN_MASK (3 << 30) |
| #define GQSPI_CONFIG_DMA_MODE (2 << 30) |
| #define GQSPI_CONFIG_CPHA_MASK BIT(2) |
| #define GQSPI_CONFIG_CPOL_MASK BIT(1) |
| |
| /* |
| * QSPI Interrupt Registers bit Masks |
| * |
| * All the four interrupt registers (Status/Mask/Enable/Disable) have the same |
| * bit definitions. |
| */ |
| #define GQSPI_IXR_TXNFULL_MASK 0x00000004 /* QSPI TX FIFO Overflow */ |
| #define GQSPI_IXR_TXFULL_MASK 0x00000008 /* QSPI TX FIFO is full */ |
| #define GQSPI_IXR_RXNEMTY_MASK 0x00000010 /* QSPI RX FIFO Not Empty */ |
| #define GQSPI_IXR_GFEMTY_MASK 0x00000080 /* QSPI Generic FIFO Empty */ |
| #define GQSPI_IXR_ALL_MASK (GQSPI_IXR_TXNFULL_MASK | \ |
| GQSPI_IXR_RXNEMTY_MASK) |
| |
| /* |
| * QSPI Enable Register bit Masks |
| * |
| * This register is used to enable or disable the QSPI controller |
| */ |
| #define GQSPI_ENABLE_ENABLE_MASK 0x00000001 /* QSPI Enable Bit Mask */ |
| |
| #define GQSPI_GFIFO_LOW_BUS BIT(14) |
| #define GQSPI_GFIFO_CS_LOWER BIT(12) |
| #define GQSPI_GFIFO_UP_BUS BIT(15) |
| #define GQSPI_GFIFO_CS_UPPER BIT(13) |
| #define GQSPI_SPI_MODE_QSPI (3 << 10) |
| #define GQSPI_SPI_MODE_SPI BIT(10) |
| #define GQSPI_SPI_MODE_DUAL_SPI (2 << 10) |
| #define GQSPI_IMD_DATA_CS_ASSERT 5 |
| #define GQSPI_IMD_DATA_CS_DEASSERT 5 |
| #define GQSPI_GFIFO_TX BIT(16) |
| #define GQSPI_GFIFO_RX BIT(17) |
| #define GQSPI_GFIFO_STRIPE_MASK BIT(18) |
| #define GQSPI_GFIFO_IMD_MASK 0xFF |
| #define GQSPI_GFIFO_EXP_MASK BIT(9) |
| #define GQSPI_GFIFO_DATA_XFR_MASK BIT(8) |
| #define GQSPI_STRT_GEN_FIFO BIT(28) |
| #define GQSPI_GEN_FIFO_STRT_MOD BIT(29) |
| #define GQSPI_GFIFO_WP_HOLD BIT(19) |
| #define GQSPI_BAUD_DIV_MASK (7 << 3) |
| #define GQSPI_DFLT_BAUD_RATE_DIV BIT(3) |
| #define GQSPI_GFIFO_ALL_INT_MASK 0xFBE |
| #define GQSPI_DMA_DST_I_STS_DONE BIT(1) |
| #define GQSPI_DMA_DST_I_STS_MASK 0xFE |
| #define MODEBITS 0x6 |
| |
| #define GQSPI_GFIFO_SELECT BIT(0) |
| #define GQSPI_FIFO_THRESHOLD 1 |
| |
| #define SPI_XFER_ON_BOTH 0 |
| #define SPI_XFER_ON_LOWER 1 |
| #define SPI_XFER_ON_UPPER 2 |
| |
| #define GQSPI_DMA_ALIGN 0x4 |
| #define GQSPI_MAX_BAUD_RATE_VAL 7 |
| #define GQSPI_DFLT_BAUD_RATE_VAL 2 |
| |
| #define GQSPI_TIMEOUT 100000000 |
| |
| #define GQSPI_BAUD_DIV_SHIFT 2 |
| #define GQSPI_LPBK_DLY_ADJ_LPBK_SHIFT 5 |
| #define GQSPI_LPBK_DLY_ADJ_DLY_1 0x2 |
| #define GQSPI_LPBK_DLY_ADJ_DLY_1_SHIFT 3 |
| #define GQSPI_LPBK_DLY_ADJ_DLY_0 0x3 |
| #define GQSPI_USE_DATA_DLY 0x1 |
| #define GQSPI_USE_DATA_DLY_SHIFT 31 |
| #define GQSPI_DATA_DLY_ADJ_VALUE 0x2 |
| #define GQSPI_DATA_DLY_ADJ_SHIFT 28 |
| #define TAP_DLY_BYPASS_LQSPI_RX_VALUE 0x1 |
| #define TAP_DLY_BYPASS_LQSPI_RX_SHIFT 2 |
| #define GQSPI_DATA_DLY_ADJ_OFST 0x000001F8 |
| #define IOU_TAPDLY_BYPASS_OFST 0xFF180390 |
| #define GQSPI_LPBK_DLY_ADJ_LPBK_MASK 0x00000020 |
| #define GQSPI_FREQ_40MHZ 40000000 |
| #define GQSPI_FREQ_100MHZ 100000000 |
| #define GQSPI_FREQ_150MHZ 150000000 |
| #define IOU_TAPDLY_BYPASS_MASK 0x7 |
| |
| #define GQSPI_REG_OFFSET 0x100 |
| #define GQSPI_DMA_REG_OFFSET 0x800 |
| |
| /* QSPI register offsets */ |
| struct zynqmp_qspi_regs { |
| u32 confr; /* 0x00 */ |
| u32 isr; /* 0x04 */ |
| u32 ier; /* 0x08 */ |
| u32 idisr; /* 0x0C */ |
| u32 imaskr; /* 0x10 */ |
| u32 enbr; /* 0x14 */ |
| u32 dr; /* 0x18 */ |
| u32 txd0r; /* 0x1C */ |
| u32 drxr; /* 0x20 */ |
| u32 sicr; /* 0x24 */ |
| u32 txftr; /* 0x28 */ |
| u32 rxftr; /* 0x2C */ |
| u32 gpior; /* 0x30 */ |
| u32 reserved0; /* 0x34 */ |
| u32 lpbkdly; /* 0x38 */ |
| u32 reserved1; /* 0x3C */ |
| u32 genfifo; /* 0x40 */ |
| u32 gqspisel; /* 0x44 */ |
| u32 reserved2; /* 0x48 */ |
| u32 gqfifoctrl; /* 0x4C */ |
| u32 gqfthr; /* 0x50 */ |
| u32 gqpollcfg; /* 0x54 */ |
| u32 gqpollto; /* 0x58 */ |
| u32 gqxfersts; /* 0x5C */ |
| u32 gqfifosnap; /* 0x60 */ |
| u32 gqrxcpy; /* 0x64 */ |
| u32 reserved3[36]; /* 0x68 */ |
| u32 gqspidlyadj; /* 0xF8 */ |
| }; |
| |
| struct zynqmp_qspi_dma_regs { |
| u32 dmadst; /* 0x00 */ |
| u32 dmasize; /* 0x04 */ |
| u32 dmasts; /* 0x08 */ |
| u32 dmactrl; /* 0x0C */ |
| u32 reserved0; /* 0x10 */ |
| u32 dmaisr; /* 0x14 */ |
| u32 dmaier; /* 0x18 */ |
| u32 dmaidr; /* 0x1C */ |
| u32 dmaimr; /* 0x20 */ |
| u32 dmactrl2; /* 0x24 */ |
| u32 dmadstmsb; /* 0x28 */ |
| }; |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| struct zynqmp_qspi_platdata { |
| struct zynqmp_qspi_regs *regs; |
| struct zynqmp_qspi_dma_regs *dma_regs; |
| u32 frequency; |
| u32 speed_hz; |
| }; |
| |
| struct zynqmp_qspi_priv { |
| struct zynqmp_qspi_regs *regs; |
| struct zynqmp_qspi_dma_regs *dma_regs; |
| const void *tx_buf; |
| void *rx_buf; |
| unsigned int len; |
| int bytes_to_transfer; |
| int bytes_to_receive; |
| unsigned int is_inst; |
| unsigned int cs_change:1; |
| }; |
| |
| static int zynqmp_qspi_ofdata_to_platdata(struct udevice *bus) |
| { |
| struct zynqmp_qspi_platdata *plat = bus->platdata; |
| |
| debug("%s\n", __func__); |
| |
| plat->regs = (struct zynqmp_qspi_regs *)(devfdt_get_addr(bus) + |
| GQSPI_REG_OFFSET); |
| plat->dma_regs = (struct zynqmp_qspi_dma_regs *) |
| (devfdt_get_addr(bus) + GQSPI_DMA_REG_OFFSET); |
| |
| return 0; |
| } |
| |
| static void zynqmp_qspi_init_hw(struct zynqmp_qspi_priv *priv) |
| { |
| u32 config_reg; |
| struct zynqmp_qspi_regs *regs = priv->regs; |
| |
| writel(GQSPI_GFIFO_SELECT, ®s->gqspisel); |
| writel(GQSPI_GFIFO_ALL_INT_MASK, ®s->idisr); |
| writel(GQSPI_FIFO_THRESHOLD, ®s->txftr); |
| writel(GQSPI_FIFO_THRESHOLD, ®s->rxftr); |
| writel(GQSPI_GFIFO_ALL_INT_MASK, ®s->isr); |
| |
| config_reg = readl(®s->confr); |
| config_reg &= ~(GQSPI_GFIFO_STRT_MODE_MASK | |
| GQSPI_CONFIG_MODE_EN_MASK); |
| config_reg |= GQSPI_CONFIG_DMA_MODE | |
| GQSPI_GFIFO_WP_HOLD | |
| GQSPI_DFLT_BAUD_RATE_DIV; |
| writel(config_reg, ®s->confr); |
| |
| writel(GQSPI_ENABLE_ENABLE_MASK, ®s->enbr); |
| } |
| |
| static u32 zynqmp_qspi_bus_select(struct zynqmp_qspi_priv *priv) |
| { |
| u32 gqspi_fifo_reg = 0; |
| |
| gqspi_fifo_reg = GQSPI_GFIFO_LOW_BUS | |
| GQSPI_GFIFO_CS_LOWER; |
| |
| return gqspi_fifo_reg; |
| } |
| |
| static void zynqmp_qspi_fill_gen_fifo(struct zynqmp_qspi_priv *priv, |
| u32 gqspi_fifo_reg) |
| { |
| struct zynqmp_qspi_regs *regs = priv->regs; |
| int ret = 0; |
| |
| ret = wait_for_bit_le32(®s->isr, GQSPI_IXR_GFEMTY_MASK, 1, |
| GQSPI_TIMEOUT, 1); |
| if (ret) |
| printf("%s Timeout\n", __func__); |
| |
| writel(gqspi_fifo_reg, ®s->genfifo); |
| } |
| |
| static void zynqmp_qspi_chipselect(struct zynqmp_qspi_priv *priv, int is_on) |
| { |
| u32 gqspi_fifo_reg = 0; |
| |
| if (is_on) { |
| gqspi_fifo_reg = zynqmp_qspi_bus_select(priv); |
| gqspi_fifo_reg |= GQSPI_SPI_MODE_SPI | |
| GQSPI_IMD_DATA_CS_ASSERT; |
| } else { |
| gqspi_fifo_reg = GQSPI_GFIFO_LOW_BUS; |
| gqspi_fifo_reg |= GQSPI_IMD_DATA_CS_DEASSERT; |
| } |
| |
| debug("GFIFO_CMD_CS: 0x%x\n", gqspi_fifo_reg); |
| |
| zynqmp_qspi_fill_gen_fifo(priv, gqspi_fifo_reg); |
| } |
| |
| void zynqmp_qspi_set_tapdelay(struct udevice *bus, u32 baudrateval) |
| { |
| struct zynqmp_qspi_platdata *plat = bus->platdata; |
| struct zynqmp_qspi_priv *priv = dev_get_priv(bus); |
| struct zynqmp_qspi_regs *regs = priv->regs; |
| u32 tapdlybypass = 0, lpbkdlyadj = 0, datadlyadj = 0, clk_rate; |
| u32 reqhz = 0; |
| |
| clk_rate = plat->frequency; |
| reqhz = (clk_rate / (GQSPI_BAUD_DIV_SHIFT << baudrateval)); |
| |
| debug("%s, req_hz:%d, clk_rate:%d, baudrateval:%d\n", |
| __func__, reqhz, clk_rate, baudrateval); |
| |
| if (reqhz < GQSPI_FREQ_40MHZ) { |
| zynqmp_mmio_read(IOU_TAPDLY_BYPASS_OFST, &tapdlybypass); |
| tapdlybypass |= (TAP_DLY_BYPASS_LQSPI_RX_VALUE << |
| TAP_DLY_BYPASS_LQSPI_RX_SHIFT); |
| } else if (reqhz <= GQSPI_FREQ_100MHZ) { |
| zynqmp_mmio_read(IOU_TAPDLY_BYPASS_OFST, &tapdlybypass); |
| tapdlybypass |= (TAP_DLY_BYPASS_LQSPI_RX_VALUE << |
| TAP_DLY_BYPASS_LQSPI_RX_SHIFT); |
| lpbkdlyadj = readl(®s->lpbkdly); |
| lpbkdlyadj |= (GQSPI_LPBK_DLY_ADJ_LPBK_MASK); |
| datadlyadj = readl(®s->gqspidlyadj); |
| datadlyadj |= ((GQSPI_USE_DATA_DLY << GQSPI_USE_DATA_DLY_SHIFT) |
| | (GQSPI_DATA_DLY_ADJ_VALUE << |
| GQSPI_DATA_DLY_ADJ_SHIFT)); |
| } else if (reqhz <= GQSPI_FREQ_150MHZ) { |
| lpbkdlyadj = readl(®s->lpbkdly); |
| lpbkdlyadj |= ((GQSPI_LPBK_DLY_ADJ_LPBK_MASK) | |
| GQSPI_LPBK_DLY_ADJ_DLY_0); |
| } |
| |
| zynqmp_mmio_write(IOU_TAPDLY_BYPASS_OFST, IOU_TAPDLY_BYPASS_MASK, |
| tapdlybypass); |
| writel(lpbkdlyadj, ®s->lpbkdly); |
| writel(datadlyadj, ®s->gqspidlyadj); |
| } |
| |
| static int zynqmp_qspi_set_speed(struct udevice *bus, uint speed) |
| { |
| struct zynqmp_qspi_platdata *plat = bus->platdata; |
| struct zynqmp_qspi_priv *priv = dev_get_priv(bus); |
| struct zynqmp_qspi_regs *regs = priv->regs; |
| u32 confr; |
| u8 baud_rate_val = 0; |
| |
| debug("%s\n", __func__); |
| if (speed > plat->frequency) |
| speed = plat->frequency; |
| |
| /* Set the clock frequency */ |
| confr = readl(®s->confr); |
| if (speed == 0) { |
| /* Set baudrate x8, if the freq is 0 */ |
| baud_rate_val = GQSPI_DFLT_BAUD_RATE_VAL; |
| } else if (plat->speed_hz != speed) { |
| while ((baud_rate_val < 8) && |
| ((plat->frequency / |
| (2 << baud_rate_val)) > speed)) |
| baud_rate_val++; |
| |
| if (baud_rate_val > GQSPI_MAX_BAUD_RATE_VAL) |
| baud_rate_val = GQSPI_DFLT_BAUD_RATE_VAL; |
| |
| plat->speed_hz = plat->frequency / (2 << baud_rate_val); |
| } |
| confr &= ~GQSPI_BAUD_DIV_MASK; |
| confr |= (baud_rate_val << 3); |
| writel(confr, ®s->confr); |
| |
| zynqmp_qspi_set_tapdelay(bus, baud_rate_val); |
| debug("regs=%p, speed=%d\n", priv->regs, plat->speed_hz); |
| |
| return 0; |
| } |
| |
| static int zynqmp_qspi_probe(struct udevice *bus) |
| { |
| struct zynqmp_qspi_platdata *plat = dev_get_platdata(bus); |
| struct zynqmp_qspi_priv *priv = dev_get_priv(bus); |
| struct clk clk; |
| unsigned long clock; |
| int ret; |
| |
| debug("%s: bus:%p, priv:%p\n", __func__, bus, priv); |
| |
| priv->regs = plat->regs; |
| priv->dma_regs = plat->dma_regs; |
| |
| ret = clk_get_by_index(bus, 0, &clk); |
| if (ret < 0) { |
| dev_err(dev, "failed to get clock\n"); |
| return ret; |
| } |
| |
| clock = clk_get_rate(&clk); |
| if (IS_ERR_VALUE(clock)) { |
| dev_err(dev, "failed to get rate\n"); |
| return clock; |
| } |
| debug("%s: CLK %ld\n", __func__, clock); |
| |
| ret = clk_enable(&clk); |
| if (ret && ret != -ENOSYS) { |
| dev_err(dev, "failed to enable clock\n"); |
| return ret; |
| } |
| plat->frequency = clock; |
| plat->speed_hz = plat->frequency / 2; |
| |
| /* init the zynq spi hw */ |
| zynqmp_qspi_init_hw(priv); |
| |
| return 0; |
| } |
| |
| static int zynqmp_qspi_set_mode(struct udevice *bus, uint mode) |
| { |
| struct zynqmp_qspi_priv *priv = dev_get_priv(bus); |
| struct zynqmp_qspi_regs *regs = priv->regs; |
| u32 confr; |
| |
| debug("%s\n", __func__); |
| /* Set the SPI Clock phase and polarities */ |
| confr = readl(®s->confr); |
| confr &= ~(GQSPI_CONFIG_CPHA_MASK | |
| GQSPI_CONFIG_CPOL_MASK); |
| |
| if (mode & SPI_CPHA) |
| confr |= GQSPI_CONFIG_CPHA_MASK; |
| if (mode & SPI_CPOL) |
| confr |= GQSPI_CONFIG_CPOL_MASK; |
| |
| writel(confr, ®s->confr); |
| |
| return 0; |
| } |
| |
| static int zynqmp_qspi_fill_tx_fifo(struct zynqmp_qspi_priv *priv, u32 size) |
| { |
| u32 data; |
| int ret = 0; |
| struct zynqmp_qspi_regs *regs = priv->regs; |
| u32 *buf = (u32 *)priv->tx_buf; |
| u32 len = size; |
| |
| debug("TxFIFO: 0x%x, size: 0x%x\n", readl(®s->isr), |
| size); |
| |
| while (size) { |
| ret = wait_for_bit_le32(®s->isr, GQSPI_IXR_TXNFULL_MASK, 1, |
| GQSPI_TIMEOUT, 1); |
| if (ret) { |
| printf("%s: Timeout\n", __func__); |
| return ret; |
| } |
| |
| if (size >= 4) { |
| writel(*buf, ®s->txd0r); |
| buf++; |
| size -= 4; |
| } else { |
| switch (size) { |
| case 1: |
| data = *((u8 *)buf); |
| buf += 1; |
| data |= GENMASK(31, 8); |
| break; |
| case 2: |
| data = *((u16 *)buf); |
| buf += 2; |
| data |= GENMASK(31, 16); |
| break; |
| case 3: |
| data = *((u16 *)buf); |
| buf += 2; |
| data |= (*((u8 *)buf) << 16); |
| buf += 1; |
| data |= GENMASK(31, 24); |
| break; |
| } |
| writel(data, ®s->txd0r); |
| size = 0; |
| } |
| } |
| |
| priv->tx_buf += len; |
| return 0; |
| } |
| |
| static void zynqmp_qspi_genfifo_cmd(struct zynqmp_qspi_priv *priv) |
| { |
| u32 gen_fifo_cmd; |
| u32 bytecount = 0; |
| |
| while (priv->len) { |
| gen_fifo_cmd = zynqmp_qspi_bus_select(priv); |
| gen_fifo_cmd |= GQSPI_GFIFO_TX | GQSPI_SPI_MODE_SPI; |
| gen_fifo_cmd |= *(u8 *)priv->tx_buf; |
| bytecount++; |
| priv->len--; |
| priv->tx_buf = (u8 *)priv->tx_buf + 1; |
| |
| debug("GFIFO_CMD_Cmd = 0x%x\n", gen_fifo_cmd); |
| |
| zynqmp_qspi_fill_gen_fifo(priv, gen_fifo_cmd); |
| } |
| } |
| |
| static u32 zynqmp_qspi_calc_exp(struct zynqmp_qspi_priv *priv, |
| u32 *gen_fifo_cmd) |
| { |
| u32 expval = 8; |
| u32 len; |
| |
| while (1) { |
| if (priv->len > 255) { |
| if (priv->len & (1 << expval)) { |
| *gen_fifo_cmd &= ~GQSPI_GFIFO_IMD_MASK; |
| *gen_fifo_cmd |= GQSPI_GFIFO_EXP_MASK; |
| *gen_fifo_cmd |= expval; |
| priv->len -= (1 << expval); |
| return expval; |
| } |
| expval++; |
| } else { |
| *gen_fifo_cmd &= ~(GQSPI_GFIFO_IMD_MASK | |
| GQSPI_GFIFO_EXP_MASK); |
| *gen_fifo_cmd |= (u8)priv->len; |
| len = (u8)priv->len; |
| priv->len = 0; |
| return len; |
| } |
| } |
| } |
| |
| static int zynqmp_qspi_genfifo_fill_tx(struct zynqmp_qspi_priv *priv) |
| { |
| u32 gen_fifo_cmd; |
| u32 len; |
| int ret = 0; |
| |
| gen_fifo_cmd = zynqmp_qspi_bus_select(priv); |
| gen_fifo_cmd |= GQSPI_GFIFO_TX | |
| GQSPI_GFIFO_DATA_XFR_MASK; |
| |
| gen_fifo_cmd |= GQSPI_SPI_MODE_SPI; |
| |
| while (priv->len) { |
| len = zynqmp_qspi_calc_exp(priv, &gen_fifo_cmd); |
| zynqmp_qspi_fill_gen_fifo(priv, gen_fifo_cmd); |
| |
| debug("GFIFO_CMD_TX:0x%x\n", gen_fifo_cmd); |
| |
| if (gen_fifo_cmd & GQSPI_GFIFO_EXP_MASK) |
| ret = zynqmp_qspi_fill_tx_fifo(priv, |
| 1 << len); |
| else |
| ret = zynqmp_qspi_fill_tx_fifo(priv, |
| len); |
| |
| if (ret) |
| return ret; |
| } |
| return ret; |
| } |
| |
| static int zynqmp_qspi_start_dma(struct zynqmp_qspi_priv *priv, |
| u32 gen_fifo_cmd, u32 *buf) |
| { |
| u32 addr; |
| u32 size, len; |
| u32 actuallen = priv->len; |
| int ret = 0; |
| struct zynqmp_qspi_dma_regs *dma_regs = priv->dma_regs; |
| |
| writel((unsigned long)buf, &dma_regs->dmadst); |
| writel(roundup(priv->len, ARCH_DMA_MINALIGN), &dma_regs->dmasize); |
| writel(GQSPI_DMA_DST_I_STS_MASK, &dma_regs->dmaier); |
| addr = (unsigned long)buf; |
| size = roundup(priv->len, ARCH_DMA_MINALIGN); |
| flush_dcache_range(addr, addr + size); |
| |
| while (priv->len) { |
| len = zynqmp_qspi_calc_exp(priv, &gen_fifo_cmd); |
| if (!(gen_fifo_cmd & GQSPI_GFIFO_EXP_MASK) && |
| (len % ARCH_DMA_MINALIGN)) { |
| gen_fifo_cmd &= ~GENMASK(7, 0); |
| gen_fifo_cmd |= roundup(len, ARCH_DMA_MINALIGN); |
| } |
| zynqmp_qspi_fill_gen_fifo(priv, gen_fifo_cmd); |
| |
| debug("GFIFO_CMD_RX:0x%x\n", gen_fifo_cmd); |
| } |
| |
| ret = wait_for_bit_le32(&dma_regs->dmaisr, GQSPI_DMA_DST_I_STS_DONE, |
| 1, GQSPI_TIMEOUT, 1); |
| if (ret) { |
| printf("DMA Timeout:0x%x\n", readl(&dma_regs->dmaisr)); |
| return -ETIMEDOUT; |
| } |
| |
| writel(GQSPI_DMA_DST_I_STS_DONE, &dma_regs->dmaisr); |
| |
| debug("buf:0x%lx, rxbuf:0x%lx, *buf:0x%x len: 0x%x\n", |
| (unsigned long)buf, (unsigned long)priv->rx_buf, *buf, |
| actuallen); |
| |
| if (buf != priv->rx_buf) |
| memcpy(priv->rx_buf, buf, actuallen); |
| |
| return 0; |
| } |
| |
| static int zynqmp_qspi_genfifo_fill_rx(struct zynqmp_qspi_priv *priv) |
| { |
| u32 gen_fifo_cmd; |
| u32 *buf; |
| u32 actuallen = priv->len; |
| |
| gen_fifo_cmd = zynqmp_qspi_bus_select(priv); |
| gen_fifo_cmd |= GQSPI_GFIFO_RX | |
| GQSPI_GFIFO_DATA_XFR_MASK; |
| |
| gen_fifo_cmd |= GQSPI_SPI_MODE_SPI; |
| |
| /* |
| * Check if receive buffer is aligned to 4 byte and length |
| * is multiples of four byte as we are using dma to receive. |
| */ |
| if (!((unsigned long)priv->rx_buf & (GQSPI_DMA_ALIGN - 1)) && |
| !(actuallen % GQSPI_DMA_ALIGN)) { |
| buf = (u32 *)priv->rx_buf; |
| return zynqmp_qspi_start_dma(priv, gen_fifo_cmd, buf); |
| } |
| |
| ALLOC_CACHE_ALIGN_BUFFER(u8, tmp, roundup(priv->len, |
| GQSPI_DMA_ALIGN)); |
| buf = (u32 *)tmp; |
| return zynqmp_qspi_start_dma(priv, gen_fifo_cmd, buf); |
| } |
| |
| static int zynqmp_qspi_start_transfer(struct zynqmp_qspi_priv *priv) |
| { |
| int ret = 0; |
| |
| if (priv->is_inst) { |
| if (priv->tx_buf) |
| zynqmp_qspi_genfifo_cmd(priv); |
| else |
| return -EINVAL; |
| } else { |
| if (priv->tx_buf) |
| ret = zynqmp_qspi_genfifo_fill_tx(priv); |
| else if (priv->rx_buf) |
| ret = zynqmp_qspi_genfifo_fill_rx(priv); |
| else |
| return -EINVAL; |
| } |
| return ret; |
| } |
| |
| static int zynqmp_qspi_transfer(struct zynqmp_qspi_priv *priv) |
| { |
| static unsigned int cs_change = 1; |
| int status = 0; |
| |
| debug("%s\n", __func__); |
| |
| while (1) { |
| /* Select the chip if required */ |
| if (cs_change) |
| zynqmp_qspi_chipselect(priv, 1); |
| |
| cs_change = priv->cs_change; |
| |
| if (!priv->tx_buf && !priv->rx_buf && priv->len) { |
| status = -EINVAL; |
| break; |
| } |
| |
| /* Request the transfer */ |
| if (priv->len) { |
| status = zynqmp_qspi_start_transfer(priv); |
| priv->is_inst = 0; |
| if (status < 0) |
| break; |
| } |
| |
| if (cs_change) |
| /* Deselect the chip */ |
| zynqmp_qspi_chipselect(priv, 0); |
| break; |
| } |
| |
| return status; |
| } |
| |
| static int zynqmp_qspi_claim_bus(struct udevice *dev) |
| { |
| struct udevice *bus = dev->parent; |
| struct zynqmp_qspi_priv *priv = dev_get_priv(bus); |
| struct zynqmp_qspi_regs *regs = priv->regs; |
| |
| writel(GQSPI_ENABLE_ENABLE_MASK, ®s->enbr); |
| |
| return 0; |
| } |
| |
| static int zynqmp_qspi_release_bus(struct udevice *dev) |
| { |
| struct udevice *bus = dev->parent; |
| struct zynqmp_qspi_priv *priv = dev_get_priv(bus); |
| struct zynqmp_qspi_regs *regs = priv->regs; |
| |
| writel(~GQSPI_ENABLE_ENABLE_MASK, ®s->enbr); |
| |
| return 0; |
| } |
| |
| int zynqmp_qspi_xfer(struct udevice *dev, unsigned int bitlen, const void *dout, |
| void *din, unsigned long flags) |
| { |
| struct udevice *bus = dev->parent; |
| struct zynqmp_qspi_priv *priv = dev_get_priv(bus); |
| |
| debug("%s: priv: 0x%08lx bitlen: %d dout: 0x%08lx ", __func__, |
| (unsigned long)priv, bitlen, (unsigned long)dout); |
| debug("din: 0x%08lx flags: 0x%lx\n", (unsigned long)din, flags); |
| |
| priv->tx_buf = dout; |
| priv->rx_buf = din; |
| priv->len = bitlen / 8; |
| |
| /* |
| * Assume that the beginning of a transfer with bits to |
| * transmit must contain a device command. |
| */ |
| if (dout && flags & SPI_XFER_BEGIN) |
| priv->is_inst = 1; |
| else |
| priv->is_inst = 0; |
| |
| if (flags & SPI_XFER_END) |
| priv->cs_change = 1; |
| else |
| priv->cs_change = 0; |
| |
| zynqmp_qspi_transfer(priv); |
| |
| return 0; |
| } |
| |
| static const struct dm_spi_ops zynqmp_qspi_ops = { |
| .claim_bus = zynqmp_qspi_claim_bus, |
| .release_bus = zynqmp_qspi_release_bus, |
| .xfer = zynqmp_qspi_xfer, |
| .set_speed = zynqmp_qspi_set_speed, |
| .set_mode = zynqmp_qspi_set_mode, |
| }; |
| |
| static const struct udevice_id zynqmp_qspi_ids[] = { |
| { .compatible = "xlnx,zynqmp-qspi-1.0" }, |
| { .compatible = "xlnx,versal-qspi-1.0" }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(zynqmp_qspi) = { |
| .name = "zynqmp_qspi", |
| .id = UCLASS_SPI, |
| .of_match = zynqmp_qspi_ids, |
| .ops = &zynqmp_qspi_ops, |
| .ofdata_to_platdata = zynqmp_qspi_ofdata_to_platdata, |
| .platdata_auto_alloc_size = sizeof(struct zynqmp_qspi_platdata), |
| .priv_auto_alloc_size = sizeof(struct zynqmp_qspi_priv), |
| .probe = zynqmp_qspi_probe, |
| }; |