| /* |
| * i2c driver for Freescale i.MX series |
| * |
| * (c) 2007 Pengutronix, Sascha Hauer <s.hauer@pengutronix.de> |
| * (c) 2011 Marek Vasut <marek.vasut@gmail.com> |
| * |
| * Based on i2c-imx.c from linux kernel: |
| * Copyright (C) 2005 Torsten Koschorrek <koschorrek at synertronixx.de> |
| * Copyright (C) 2005 Matthias Blaschke <blaschke at synertronixx.de> |
| * Copyright (C) 2007 RightHand Technologies, Inc. |
| * Copyright (C) 2008 Darius Augulis <darius.augulis at teltonika.lt> |
| * |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <common.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/imx-regs.h> |
| #include <asm/errno.h> |
| #include <asm/io.h> |
| #include <i2c.h> |
| #include <watchdog.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #ifdef I2C_QUIRK_REG |
| struct mxc_i2c_regs { |
| uint8_t iadr; |
| uint8_t ifdr; |
| uint8_t i2cr; |
| uint8_t i2sr; |
| uint8_t i2dr; |
| }; |
| #else |
| struct mxc_i2c_regs { |
| uint32_t iadr; |
| uint32_t ifdr; |
| uint32_t i2cr; |
| uint32_t i2sr; |
| uint32_t i2dr; |
| }; |
| #endif |
| |
| #define I2CR_IIEN (1 << 6) |
| #define I2CR_MSTA (1 << 5) |
| #define I2CR_MTX (1 << 4) |
| #define I2CR_TX_NO_AK (1 << 3) |
| #define I2CR_RSTA (1 << 2) |
| |
| #define I2SR_ICF (1 << 7) |
| #define I2SR_IBB (1 << 5) |
| #define I2SR_IAL (1 << 4) |
| #define I2SR_IIF (1 << 1) |
| #define I2SR_RX_NO_AK (1 << 0) |
| |
| #ifdef I2C_QUIRK_REG |
| #define I2CR_IEN (0 << 7) |
| #define I2CR_IDIS (1 << 7) |
| #define I2SR_IIF_CLEAR (1 << 1) |
| #else |
| #define I2CR_IEN (1 << 7) |
| #define I2CR_IDIS (0 << 7) |
| #define I2SR_IIF_CLEAR (0 << 1) |
| #endif |
| |
| #if defined(CONFIG_HARD_I2C) && !defined(CONFIG_SYS_I2C_BASE) |
| #error "define CONFIG_SYS_I2C_BASE to use the mxc_i2c driver" |
| #endif |
| |
| #ifdef I2C_QUIRK_REG |
| static u16 i2c_clk_div[60][2] = { |
| { 20, 0x00 }, { 22, 0x01 }, { 24, 0x02 }, { 26, 0x03 }, |
| { 28, 0x04 }, { 30, 0x05 }, { 32, 0x09 }, { 34, 0x06 }, |
| { 36, 0x0A }, { 40, 0x07 }, { 44, 0x0C }, { 48, 0x0D }, |
| { 52, 0x43 }, { 56, 0x0E }, { 60, 0x45 }, { 64, 0x12 }, |
| { 68, 0x0F }, { 72, 0x13 }, { 80, 0x14 }, { 88, 0x15 }, |
| { 96, 0x19 }, { 104, 0x16 }, { 112, 0x1A }, { 128, 0x17 }, |
| { 136, 0x4F }, { 144, 0x1C }, { 160, 0x1D }, { 176, 0x55 }, |
| { 192, 0x1E }, { 208, 0x56 }, { 224, 0x22 }, { 228, 0x24 }, |
| { 240, 0x1F }, { 256, 0x23 }, { 288, 0x5C }, { 320, 0x25 }, |
| { 384, 0x26 }, { 448, 0x2A }, { 480, 0x27 }, { 512, 0x2B }, |
| { 576, 0x2C }, { 640, 0x2D }, { 768, 0x31 }, { 896, 0x32 }, |
| { 960, 0x2F }, { 1024, 0x33 }, { 1152, 0x34 }, { 1280, 0x35 }, |
| { 1536, 0x36 }, { 1792, 0x3A }, { 1920, 0x37 }, { 2048, 0x3B }, |
| { 2304, 0x3C }, { 2560, 0x3D }, { 3072, 0x3E }, { 3584, 0x7A }, |
| { 3840, 0x3F }, { 4096, 0x7B }, { 5120, 0x7D }, { 6144, 0x7E }, |
| }; |
| #else |
| static u16 i2c_clk_div[50][2] = { |
| { 22, 0x20 }, { 24, 0x21 }, { 26, 0x22 }, { 28, 0x23 }, |
| { 30, 0x00 }, { 32, 0x24 }, { 36, 0x25 }, { 40, 0x26 }, |
| { 42, 0x03 }, { 44, 0x27 }, { 48, 0x28 }, { 52, 0x05 }, |
| { 56, 0x29 }, { 60, 0x06 }, { 64, 0x2A }, { 72, 0x2B }, |
| { 80, 0x2C }, { 88, 0x09 }, { 96, 0x2D }, { 104, 0x0A }, |
| { 112, 0x2E }, { 128, 0x2F }, { 144, 0x0C }, { 160, 0x30 }, |
| { 192, 0x31 }, { 224, 0x32 }, { 240, 0x0F }, { 256, 0x33 }, |
| { 288, 0x10 }, { 320, 0x34 }, { 384, 0x35 }, { 448, 0x36 }, |
| { 480, 0x13 }, { 512, 0x37 }, { 576, 0x14 }, { 640, 0x38 }, |
| { 768, 0x39 }, { 896, 0x3A }, { 960, 0x17 }, { 1024, 0x3B }, |
| { 1152, 0x18 }, { 1280, 0x3C }, { 1536, 0x3D }, { 1792, 0x3E }, |
| { 1920, 0x1B }, { 2048, 0x3F }, { 2304, 0x1C }, { 2560, 0x1D }, |
| { 3072, 0x1E }, { 3840, 0x1F } |
| }; |
| #endif |
| |
| |
| #ifndef CONFIG_SYS_MXC_I2C1_SPEED |
| #define CONFIG_SYS_MXC_I2C1_SPEED 100000 |
| #endif |
| #ifndef CONFIG_SYS_MXC_I2C2_SPEED |
| #define CONFIG_SYS_MXC_I2C2_SPEED 100000 |
| #endif |
| #ifndef CONFIG_SYS_MXC_I2C3_SPEED |
| #define CONFIG_SYS_MXC_I2C3_SPEED 100000 |
| #endif |
| #ifndef CONFIG_SYS_MXC_I2C4_SPEED |
| #define CONFIG_SYS_MXC_I2C4_SPEED 100000 |
| #endif |
| |
| #ifndef CONFIG_SYS_MXC_I2C1_SLAVE |
| #define CONFIG_SYS_MXC_I2C1_SLAVE 0 |
| #endif |
| #ifndef CONFIG_SYS_MXC_I2C2_SLAVE |
| #define CONFIG_SYS_MXC_I2C2_SLAVE 0 |
| #endif |
| #ifndef CONFIG_SYS_MXC_I2C3_SLAVE |
| #define CONFIG_SYS_MXC_I2C3_SLAVE 0 |
| #endif |
| #ifndef CONFIG_SYS_MXC_I2C4_SLAVE |
| #define CONFIG_SYS_MXC_I2C4_SLAVE 0 |
| #endif |
| |
| |
| /* |
| * Calculate and set proper clock divider |
| */ |
| static uint8_t i2c_imx_get_clk(unsigned int rate) |
| { |
| unsigned int i2c_clk_rate; |
| unsigned int div; |
| u8 clk_div; |
| |
| #if defined(CONFIG_MX31) |
| struct clock_control_regs *sc_regs = |
| (struct clock_control_regs *)CCM_BASE; |
| |
| /* start the required I2C clock */ |
| writel(readl(&sc_regs->cgr0) | (3 << CONFIG_SYS_I2C_CLK_OFFSET), |
| &sc_regs->cgr0); |
| #endif |
| |
| /* Divider value calculation */ |
| i2c_clk_rate = mxc_get_clock(MXC_I2C_CLK); |
| div = (i2c_clk_rate + rate - 1) / rate; |
| if (div < i2c_clk_div[0][0]) |
| clk_div = 0; |
| else if (div > i2c_clk_div[ARRAY_SIZE(i2c_clk_div) - 1][0]) |
| clk_div = ARRAY_SIZE(i2c_clk_div) - 1; |
| else |
| for (clk_div = 0; i2c_clk_div[clk_div][0] < div; clk_div++) |
| ; |
| |
| /* Store divider value */ |
| return clk_div; |
| } |
| |
| /* |
| * Set I2C Bus speed |
| */ |
| static int bus_i2c_set_bus_speed(void *base, int speed) |
| { |
| struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base; |
| u8 clk_idx = i2c_imx_get_clk(speed); |
| u8 idx = i2c_clk_div[clk_idx][1]; |
| |
| /* Store divider value */ |
| writeb(idx, &i2c_regs->ifdr); |
| |
| /* Reset module */ |
| writeb(I2CR_IDIS, &i2c_regs->i2cr); |
| writeb(0, &i2c_regs->i2sr); |
| return 0; |
| } |
| |
| #define ST_BUS_IDLE (0 | (I2SR_IBB << 8)) |
| #define ST_BUS_BUSY (I2SR_IBB | (I2SR_IBB << 8)) |
| #define ST_IIF (I2SR_IIF | (I2SR_IIF << 8)) |
| |
| static int wait_for_sr_state(struct mxc_i2c_regs *i2c_regs, unsigned state) |
| { |
| unsigned sr; |
| ulong elapsed; |
| ulong start_time = get_timer(0); |
| for (;;) { |
| sr = readb(&i2c_regs->i2sr); |
| if (sr & I2SR_IAL) { |
| #ifdef I2C_QUIRK_REG |
| writeb(sr | I2SR_IAL, &i2c_regs->i2sr); |
| #else |
| writeb(sr & ~I2SR_IAL, &i2c_regs->i2sr); |
| #endif |
| printf("%s: Arbitration lost sr=%x cr=%x state=%x\n", |
| __func__, sr, readb(&i2c_regs->i2cr), state); |
| return -ERESTART; |
| } |
| if ((sr & (state >> 8)) == (unsigned char)state) |
| return sr; |
| WATCHDOG_RESET(); |
| elapsed = get_timer(start_time); |
| if (elapsed > (CONFIG_SYS_HZ / 10)) /* .1 seconds */ |
| break; |
| } |
| printf("%s: failed sr=%x cr=%x state=%x\n", __func__, |
| sr, readb(&i2c_regs->i2cr), state); |
| return -ETIMEDOUT; |
| } |
| |
| static int tx_byte(struct mxc_i2c_regs *i2c_regs, u8 byte) |
| { |
| int ret; |
| |
| writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr); |
| writeb(byte, &i2c_regs->i2dr); |
| ret = wait_for_sr_state(i2c_regs, ST_IIF); |
| if (ret < 0) |
| return ret; |
| if (ret & I2SR_RX_NO_AK) |
| return -ENODEV; |
| return 0; |
| } |
| |
| /* |
| * Stop I2C transaction |
| */ |
| static void i2c_imx_stop(struct mxc_i2c_regs *i2c_regs) |
| { |
| int ret; |
| unsigned int temp = readb(&i2c_regs->i2cr); |
| |
| temp &= ~(I2CR_MSTA | I2CR_MTX); |
| writeb(temp, &i2c_regs->i2cr); |
| ret = wait_for_sr_state(i2c_regs, ST_BUS_IDLE); |
| if (ret < 0) |
| printf("%s:trigger stop failed\n", __func__); |
| } |
| |
| /* |
| * Send start signal, chip address and |
| * write register address |
| */ |
| static int i2c_init_transfer_(struct mxc_i2c_regs *i2c_regs, |
| uchar chip, uint addr, int alen) |
| { |
| unsigned int temp; |
| int ret; |
| |
| /* Enable I2C controller */ |
| #ifdef I2C_QUIRK_REG |
| if (readb(&i2c_regs->i2cr) & I2CR_IDIS) { |
| #else |
| if (!(readb(&i2c_regs->i2cr) & I2CR_IEN)) { |
| #endif |
| writeb(I2CR_IEN, &i2c_regs->i2cr); |
| /* Wait for controller to be stable */ |
| udelay(50); |
| } |
| if (readb(&i2c_regs->iadr) == (chip << 1)) |
| writeb((chip << 1) ^ 2, &i2c_regs->iadr); |
| writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr); |
| ret = wait_for_sr_state(i2c_regs, ST_BUS_IDLE); |
| if (ret < 0) |
| return ret; |
| |
| /* Start I2C transaction */ |
| temp = readb(&i2c_regs->i2cr); |
| temp |= I2CR_MSTA; |
| writeb(temp, &i2c_regs->i2cr); |
| |
| ret = wait_for_sr_state(i2c_regs, ST_BUS_BUSY); |
| if (ret < 0) |
| return ret; |
| |
| temp |= I2CR_MTX | I2CR_TX_NO_AK; |
| writeb(temp, &i2c_regs->i2cr); |
| |
| /* write slave address */ |
| ret = tx_byte(i2c_regs, chip << 1); |
| if (ret < 0) |
| return ret; |
| |
| while (alen--) { |
| ret = tx_byte(i2c_regs, (addr >> (alen * 8)) & 0xff); |
| if (ret < 0) |
| return ret; |
| } |
| return 0; |
| } |
| |
| static int i2c_idle_bus(void *base); |
| |
| static int i2c_init_transfer(struct mxc_i2c_regs *i2c_regs, |
| uchar chip, uint addr, int alen) |
| { |
| int retry; |
| int ret; |
| for (retry = 0; retry < 3; retry++) { |
| ret = i2c_init_transfer_(i2c_regs, chip, addr, alen); |
| if (ret >= 0) |
| return 0; |
| i2c_imx_stop(i2c_regs); |
| if (ret == -ENODEV) |
| return ret; |
| |
| printf("%s: failed for chip 0x%x retry=%d\n", __func__, chip, |
| retry); |
| if (ret != -ERESTART) |
| /* Disable controller */ |
| writeb(I2CR_IDIS, &i2c_regs->i2cr); |
| udelay(100); |
| if (i2c_idle_bus(i2c_regs) < 0) |
| break; |
| } |
| printf("%s: give up i2c_regs=%p\n", __func__, i2c_regs); |
| return ret; |
| } |
| |
| /* |
| * Read data from I2C device |
| */ |
| int bus_i2c_read(void *base, uchar chip, uint addr, int alen, uchar *buf, |
| int len) |
| { |
| int ret; |
| unsigned int temp; |
| int i; |
| struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base; |
| |
| ret = i2c_init_transfer(i2c_regs, chip, addr, alen); |
| if (ret < 0) |
| return ret; |
| |
| temp = readb(&i2c_regs->i2cr); |
| temp |= I2CR_RSTA; |
| writeb(temp, &i2c_regs->i2cr); |
| |
| ret = tx_byte(i2c_regs, (chip << 1) | 1); |
| if (ret < 0) { |
| i2c_imx_stop(i2c_regs); |
| return ret; |
| } |
| |
| /* setup bus to read data */ |
| temp = readb(&i2c_regs->i2cr); |
| temp &= ~(I2CR_MTX | I2CR_TX_NO_AK); |
| if (len == 1) |
| temp |= I2CR_TX_NO_AK; |
| writeb(temp, &i2c_regs->i2cr); |
| writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr); |
| readb(&i2c_regs->i2dr); /* dummy read to clear ICF */ |
| |
| /* read data */ |
| for (i = 0; i < len; i++) { |
| ret = wait_for_sr_state(i2c_regs, ST_IIF); |
| if (ret < 0) { |
| i2c_imx_stop(i2c_regs); |
| return ret; |
| } |
| |
| /* |
| * It must generate STOP before read I2DR to prevent |
| * controller from generating another clock cycle |
| */ |
| if (i == (len - 1)) { |
| i2c_imx_stop(i2c_regs); |
| } else if (i == (len - 2)) { |
| temp = readb(&i2c_regs->i2cr); |
| temp |= I2CR_TX_NO_AK; |
| writeb(temp, &i2c_regs->i2cr); |
| } |
| writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr); |
| buf[i] = readb(&i2c_regs->i2dr); |
| } |
| i2c_imx_stop(i2c_regs); |
| return 0; |
| } |
| |
| /* |
| * Write data to I2C device |
| */ |
| int bus_i2c_write(void *base, uchar chip, uint addr, int alen, |
| const uchar *buf, int len) |
| { |
| int ret; |
| int i; |
| struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base; |
| |
| ret = i2c_init_transfer(i2c_regs, chip, addr, alen); |
| if (ret < 0) |
| return ret; |
| |
| for (i = 0; i < len; i++) { |
| ret = tx_byte(i2c_regs, buf[i]); |
| if (ret < 0) |
| break; |
| } |
| i2c_imx_stop(i2c_regs); |
| return ret; |
| } |
| |
| static void * const i2c_bases[] = { |
| #if defined(CONFIG_MX25) |
| (void *)IMX_I2C_BASE, |
| (void *)IMX_I2C2_BASE, |
| (void *)IMX_I2C3_BASE |
| #elif defined(CONFIG_MX27) |
| (void *)IMX_I2C1_BASE, |
| (void *)IMX_I2C2_BASE |
| #elif defined(CONFIG_MX31) || defined(CONFIG_MX35) || \ |
| defined(CONFIG_MX51) || defined(CONFIG_MX53) || \ |
| defined(CONFIG_MX6) || defined(CONFIG_LS102XA) |
| (void *)I2C1_BASE_ADDR, |
| (void *)I2C2_BASE_ADDR, |
| (void *)I2C3_BASE_ADDR |
| #elif defined(CONFIG_VF610) |
| (void *)I2C0_BASE_ADDR |
| #elif defined(CONFIG_FSL_LSCH3) |
| (void *)I2C1_BASE_ADDR, |
| (void *)I2C2_BASE_ADDR, |
| (void *)I2C3_BASE_ADDR, |
| (void *)I2C4_BASE_ADDR |
| #else |
| #error "architecture not supported" |
| #endif |
| }; |
| |
| struct i2c_parms { |
| void *base; |
| void *idle_bus_data; |
| int (*idle_bus_fn)(void *p); |
| }; |
| |
| struct sram_data { |
| unsigned curr_i2c_bus; |
| struct i2c_parms i2c_data[ARRAY_SIZE(i2c_bases)]; |
| }; |
| |
| void *i2c_get_base(struct i2c_adapter *adap) |
| { |
| return i2c_bases[adap->hwadapnr]; |
| } |
| |
| static struct i2c_parms *i2c_get_parms(void *base) |
| { |
| struct sram_data *srdata = (void *)gd->srdata; |
| int i = 0; |
| struct i2c_parms *p = srdata->i2c_data; |
| while (i < ARRAY_SIZE(srdata->i2c_data)) { |
| if (p->base == base) |
| return p; |
| p++; |
| i++; |
| } |
| printf("Invalid I2C base: %p\n", base); |
| return NULL; |
| } |
| |
| static int i2c_idle_bus(void *base) |
| { |
| struct i2c_parms *p = i2c_get_parms(base); |
| if (p && p->idle_bus_fn) |
| return p->idle_bus_fn(p->idle_bus_data); |
| return 0; |
| } |
| |
| static int mxc_i2c_read(struct i2c_adapter *adap, uint8_t chip, |
| uint addr, int alen, uint8_t *buffer, |
| int len) |
| { |
| return bus_i2c_read(i2c_get_base(adap), chip, addr, alen, buffer, len); |
| } |
| |
| static int mxc_i2c_write(struct i2c_adapter *adap, uint8_t chip, |
| uint addr, int alen, uint8_t *buffer, |
| int len) |
| { |
| return bus_i2c_write(i2c_get_base(adap), chip, addr, alen, buffer, len); |
| } |
| |
| /* |
| * Test if a chip at a given address responds (probe the chip) |
| */ |
| static int mxc_i2c_probe(struct i2c_adapter *adap, uint8_t chip) |
| { |
| return bus_i2c_write(i2c_get_base(adap), chip, 0, 0, NULL, 0); |
| } |
| |
| void bus_i2c_init(void *base, int speed, int unused, |
| int (*idle_bus_fn)(void *p), void *idle_bus_data) |
| { |
| struct sram_data *srdata = (void *)gd->srdata; |
| int i = 0; |
| struct i2c_parms *p = srdata->i2c_data; |
| if (!base) |
| return; |
| for (;;) { |
| if (!p->base || (p->base == base)) { |
| p->base = base; |
| if (idle_bus_fn) { |
| p->idle_bus_fn = idle_bus_fn; |
| p->idle_bus_data = idle_bus_data; |
| } |
| break; |
| } |
| p++; |
| i++; |
| if (i >= ARRAY_SIZE(srdata->i2c_data)) |
| return; |
| } |
| bus_i2c_set_bus_speed(base, speed); |
| } |
| |
| /* |
| * Init I2C Bus |
| */ |
| static void mxc_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr) |
| { |
| bus_i2c_init(i2c_get_base(adap), speed, slaveaddr, NULL, NULL); |
| } |
| |
| /* |
| * Set I2C Speed |
| */ |
| static uint mxc_i2c_set_bus_speed(struct i2c_adapter *adap, uint speed) |
| { |
| return bus_i2c_set_bus_speed(i2c_get_base(adap), speed); |
| } |
| |
| /* |
| * Register mxc i2c adapters |
| */ |
| U_BOOT_I2C_ADAP_COMPLETE(mxc0, mxc_i2c_init, mxc_i2c_probe, |
| mxc_i2c_read, mxc_i2c_write, |
| mxc_i2c_set_bus_speed, |
| CONFIG_SYS_MXC_I2C1_SPEED, |
| CONFIG_SYS_MXC_I2C1_SLAVE, 0) |
| U_BOOT_I2C_ADAP_COMPLETE(mxc1, mxc_i2c_init, mxc_i2c_probe, |
| mxc_i2c_read, mxc_i2c_write, |
| mxc_i2c_set_bus_speed, |
| CONFIG_SYS_MXC_I2C2_SPEED, |
| CONFIG_SYS_MXC_I2C2_SLAVE, 1) |
| #ifdef CONFIG_SYS_I2C_MXC_I2C3 |
| U_BOOT_I2C_ADAP_COMPLETE(mxc2, mxc_i2c_init, mxc_i2c_probe, |
| mxc_i2c_read, mxc_i2c_write, |
| mxc_i2c_set_bus_speed, |
| CONFIG_SYS_MXC_I2C3_SPEED, |
| CONFIG_SYS_MXC_I2C3_SLAVE, 2) |
| #endif |
| #ifdef CONFIG_SYS_I2C_MXC_I2C4 |
| U_BOOT_I2C_ADAP_COMPLETE(mxc3, mxc_i2c_init, mxc_i2c_probe, |
| mxc_i2c_read, mxc_i2c_write, |
| mxc_i2c_set_bus_speed, |
| CONFIG_SYS_MXC_I2C4_SPEED, |
| CONFIG_SYS_MXC_I2C4_SLAVE, 3) |
| #endif |