| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2018 MediaTek Inc. |
| * |
| * Author: Weijie Gao <weijie.gao@mediatek.com> |
| * Author: Mark Lee <mark-mc.lee@mediatek.com> |
| */ |
| |
| #include <common.h> |
| #include <cpu_func.h> |
| #include <dm.h> |
| #include <log.h> |
| #include <malloc.h> |
| #include <miiphy.h> |
| #include <net.h> |
| #include <regmap.h> |
| #include <reset.h> |
| #include <syscon.h> |
| #include <wait_bit.h> |
| #include <asm/cache.h> |
| #include <asm/gpio.h> |
| #include <asm/io.h> |
| #include <dm/device_compat.h> |
| #include <linux/delay.h> |
| #include <linux/err.h> |
| #include <linux/ioport.h> |
| #include <linux/mdio.h> |
| #include <linux/mii.h> |
| |
| #include "mtk_eth.h" |
| |
| #define NUM_TX_DESC 24 |
| #define NUM_RX_DESC 24 |
| #define TX_TOTAL_BUF_SIZE (NUM_TX_DESC * PKTSIZE_ALIGN) |
| #define RX_TOTAL_BUF_SIZE (NUM_RX_DESC * PKTSIZE_ALIGN) |
| #define TOTAL_PKT_BUF_SIZE (TX_TOTAL_BUF_SIZE + RX_TOTAL_BUF_SIZE) |
| |
| #define MT753X_NUM_PHYS 5 |
| #define MT753X_NUM_PORTS 7 |
| #define MT753X_DFL_SMI_ADDR 31 |
| #define MT753X_SMI_ADDR_MASK 0x1f |
| |
| #define MT753X_PHY_ADDR(base, addr) \ |
| (((base) + (addr)) & 0x1f) |
| |
| #define GDMA_FWD_TO_CPU \ |
| (0x20000000 | \ |
| GDM_ICS_EN | \ |
| GDM_TCS_EN | \ |
| GDM_UCS_EN | \ |
| STRP_CRC | \ |
| (DP_PDMA << MYMAC_DP_S) | \ |
| (DP_PDMA << BC_DP_S) | \ |
| (DP_PDMA << MC_DP_S) | \ |
| (DP_PDMA << UN_DP_S)) |
| |
| #define GDMA_FWD_DISCARD \ |
| (0x20000000 | \ |
| GDM_ICS_EN | \ |
| GDM_TCS_EN | \ |
| GDM_UCS_EN | \ |
| STRP_CRC | \ |
| (DP_DISCARD << MYMAC_DP_S) | \ |
| (DP_DISCARD << BC_DP_S) | \ |
| (DP_DISCARD << MC_DP_S) | \ |
| (DP_DISCARD << UN_DP_S)) |
| |
| struct pdma_rxd_info1 { |
| u32 PDP0; |
| }; |
| |
| struct pdma_rxd_info2 { |
| u32 PLEN1 : 14; |
| u32 LS1 : 1; |
| u32 UN_USED : 1; |
| u32 PLEN0 : 14; |
| u32 LS0 : 1; |
| u32 DDONE : 1; |
| }; |
| |
| struct pdma_rxd_info3 { |
| u32 PDP1; |
| }; |
| |
| struct pdma_rxd_info4 { |
| u32 FOE_ENTRY : 14; |
| u32 CRSN : 5; |
| u32 SP : 3; |
| u32 L4F : 1; |
| u32 L4VLD : 1; |
| u32 TACK : 1; |
| u32 IP4F : 1; |
| u32 IP4 : 1; |
| u32 IP6 : 1; |
| u32 UN_USED : 4; |
| }; |
| |
| struct pdma_rxdesc { |
| struct pdma_rxd_info1 rxd_info1; |
| struct pdma_rxd_info2 rxd_info2; |
| struct pdma_rxd_info3 rxd_info3; |
| struct pdma_rxd_info4 rxd_info4; |
| }; |
| |
| struct pdma_txd_info1 { |
| u32 SDP0; |
| }; |
| |
| struct pdma_txd_info2 { |
| u32 SDL1 : 14; |
| u32 LS1 : 1; |
| u32 BURST : 1; |
| u32 SDL0 : 14; |
| u32 LS0 : 1; |
| u32 DDONE : 1; |
| }; |
| |
| struct pdma_txd_info3 { |
| u32 SDP1; |
| }; |
| |
| struct pdma_txd_info4 { |
| u32 VLAN_TAG : 16; |
| u32 INS : 1; |
| u32 RESV : 2; |
| u32 UDF : 6; |
| u32 FPORT : 3; |
| u32 TSO : 1; |
| u32 TUI_CO : 3; |
| }; |
| |
| struct pdma_txdesc { |
| struct pdma_txd_info1 txd_info1; |
| struct pdma_txd_info2 txd_info2; |
| struct pdma_txd_info3 txd_info3; |
| struct pdma_txd_info4 txd_info4; |
| }; |
| |
| enum mtk_switch { |
| SW_NONE, |
| SW_MT7530, |
| SW_MT7531 |
| }; |
| |
| enum mtk_soc { |
| SOC_MT7623, |
| SOC_MT7629, |
| SOC_MT7622 |
| }; |
| |
| struct mtk_eth_priv { |
| char pkt_pool[TOTAL_PKT_BUF_SIZE] __aligned(ARCH_DMA_MINALIGN); |
| |
| struct pdma_txdesc *tx_ring_noc; |
| struct pdma_rxdesc *rx_ring_noc; |
| |
| int rx_dma_owner_idx0; |
| int tx_cpu_owner_idx0; |
| |
| void __iomem *fe_base; |
| void __iomem *gmac_base; |
| void __iomem *ethsys_base; |
| void __iomem *sgmii_base; |
| |
| struct mii_dev *mdio_bus; |
| int (*mii_read)(struct mtk_eth_priv *priv, u8 phy, u8 reg); |
| int (*mii_write)(struct mtk_eth_priv *priv, u8 phy, u8 reg, u16 val); |
| int (*mmd_read)(struct mtk_eth_priv *priv, u8 addr, u8 devad, u16 reg); |
| int (*mmd_write)(struct mtk_eth_priv *priv, u8 addr, u8 devad, u16 reg, |
| u16 val); |
| |
| enum mtk_soc soc; |
| int gmac_id; |
| int force_mode; |
| int speed; |
| int duplex; |
| |
| struct phy_device *phydev; |
| int phy_interface; |
| int phy_addr; |
| |
| enum mtk_switch sw; |
| int (*switch_init)(struct mtk_eth_priv *priv); |
| u32 mt753x_smi_addr; |
| u32 mt753x_phy_base; |
| |
| struct gpio_desc rst_gpio; |
| int mcm; |
| |
| struct reset_ctl rst_fe; |
| struct reset_ctl rst_mcm; |
| }; |
| |
| static void mtk_pdma_write(struct mtk_eth_priv *priv, u32 reg, u32 val) |
| { |
| writel(val, priv->fe_base + PDMA_BASE + reg); |
| } |
| |
| static void mtk_pdma_rmw(struct mtk_eth_priv *priv, u32 reg, u32 clr, |
| u32 set) |
| { |
| clrsetbits_le32(priv->fe_base + PDMA_BASE + reg, clr, set); |
| } |
| |
| static void mtk_gdma_write(struct mtk_eth_priv *priv, int no, u32 reg, |
| u32 val) |
| { |
| u32 gdma_base; |
| |
| if (no == 1) |
| gdma_base = GDMA2_BASE; |
| else |
| gdma_base = GDMA1_BASE; |
| |
| writel(val, priv->fe_base + gdma_base + reg); |
| } |
| |
| static u32 mtk_gmac_read(struct mtk_eth_priv *priv, u32 reg) |
| { |
| return readl(priv->gmac_base + reg); |
| } |
| |
| static void mtk_gmac_write(struct mtk_eth_priv *priv, u32 reg, u32 val) |
| { |
| writel(val, priv->gmac_base + reg); |
| } |
| |
| static void mtk_gmac_rmw(struct mtk_eth_priv *priv, u32 reg, u32 clr, u32 set) |
| { |
| clrsetbits_le32(priv->gmac_base + reg, clr, set); |
| } |
| |
| static void mtk_ethsys_rmw(struct mtk_eth_priv *priv, u32 reg, u32 clr, |
| u32 set) |
| { |
| clrsetbits_le32(priv->ethsys_base + reg, clr, set); |
| } |
| |
| /* Direct MDIO clause 22/45 access via SoC */ |
| static int mtk_mii_rw(struct mtk_eth_priv *priv, u8 phy, u8 reg, u16 data, |
| u32 cmd, u32 st) |
| { |
| int ret; |
| u32 val; |
| |
| val = (st << MDIO_ST_S) | |
| ((cmd << MDIO_CMD_S) & MDIO_CMD_M) | |
| (((u32)phy << MDIO_PHY_ADDR_S) & MDIO_PHY_ADDR_M) | |
| (((u32)reg << MDIO_REG_ADDR_S) & MDIO_REG_ADDR_M); |
| |
| if (cmd == MDIO_CMD_WRITE) |
| val |= data & MDIO_RW_DATA_M; |
| |
| mtk_gmac_write(priv, GMAC_PIAC_REG, val | PHY_ACS_ST); |
| |
| ret = wait_for_bit_le32(priv->gmac_base + GMAC_PIAC_REG, |
| PHY_ACS_ST, 0, 5000, 0); |
| if (ret) { |
| pr_warn("MDIO access timeout\n"); |
| return ret; |
| } |
| |
| if (cmd == MDIO_CMD_READ) { |
| val = mtk_gmac_read(priv, GMAC_PIAC_REG); |
| return val & MDIO_RW_DATA_M; |
| } |
| |
| return 0; |
| } |
| |
| /* Direct MDIO clause 22 read via SoC */ |
| static int mtk_mii_read(struct mtk_eth_priv *priv, u8 phy, u8 reg) |
| { |
| return mtk_mii_rw(priv, phy, reg, 0, MDIO_CMD_READ, MDIO_ST_C22); |
| } |
| |
| /* Direct MDIO clause 22 write via SoC */ |
| static int mtk_mii_write(struct mtk_eth_priv *priv, u8 phy, u8 reg, u16 data) |
| { |
| return mtk_mii_rw(priv, phy, reg, data, MDIO_CMD_WRITE, MDIO_ST_C22); |
| } |
| |
| /* Direct MDIO clause 45 read via SoC */ |
| static int mtk_mmd_read(struct mtk_eth_priv *priv, u8 addr, u8 devad, u16 reg) |
| { |
| int ret; |
| |
| ret = mtk_mii_rw(priv, addr, devad, reg, MDIO_CMD_ADDR, MDIO_ST_C45); |
| if (ret) |
| return ret; |
| |
| return mtk_mii_rw(priv, addr, devad, 0, MDIO_CMD_READ_C45, |
| MDIO_ST_C45); |
| } |
| |
| /* Direct MDIO clause 45 write via SoC */ |
| static int mtk_mmd_write(struct mtk_eth_priv *priv, u8 addr, u8 devad, |
| u16 reg, u16 val) |
| { |
| int ret; |
| |
| ret = mtk_mii_rw(priv, addr, devad, reg, MDIO_CMD_ADDR, MDIO_ST_C45); |
| if (ret) |
| return ret; |
| |
| return mtk_mii_rw(priv, addr, devad, val, MDIO_CMD_WRITE, |
| MDIO_ST_C45); |
| } |
| |
| /* Indirect MDIO clause 45 read via MII registers */ |
| static int mtk_mmd_ind_read(struct mtk_eth_priv *priv, u8 addr, u8 devad, |
| u16 reg) |
| { |
| int ret; |
| |
| ret = priv->mii_write(priv, addr, MII_MMD_ACC_CTL_REG, |
| (MMD_ADDR << MMD_CMD_S) | |
| ((devad << MMD_DEVAD_S) & MMD_DEVAD_M)); |
| if (ret) |
| return ret; |
| |
| ret = priv->mii_write(priv, addr, MII_MMD_ADDR_DATA_REG, reg); |
| if (ret) |
| return ret; |
| |
| ret = priv->mii_write(priv, addr, MII_MMD_ACC_CTL_REG, |
| (MMD_DATA << MMD_CMD_S) | |
| ((devad << MMD_DEVAD_S) & MMD_DEVAD_M)); |
| if (ret) |
| return ret; |
| |
| return priv->mii_read(priv, addr, MII_MMD_ADDR_DATA_REG); |
| } |
| |
| /* Indirect MDIO clause 45 write via MII registers */ |
| static int mtk_mmd_ind_write(struct mtk_eth_priv *priv, u8 addr, u8 devad, |
| u16 reg, u16 val) |
| { |
| int ret; |
| |
| ret = priv->mii_write(priv, addr, MII_MMD_ACC_CTL_REG, |
| (MMD_ADDR << MMD_CMD_S) | |
| ((devad << MMD_DEVAD_S) & MMD_DEVAD_M)); |
| if (ret) |
| return ret; |
| |
| ret = priv->mii_write(priv, addr, MII_MMD_ADDR_DATA_REG, reg); |
| if (ret) |
| return ret; |
| |
| ret = priv->mii_write(priv, addr, MII_MMD_ACC_CTL_REG, |
| (MMD_DATA << MMD_CMD_S) | |
| ((devad << MMD_DEVAD_S) & MMD_DEVAD_M)); |
| if (ret) |
| return ret; |
| |
| return priv->mii_write(priv, addr, MII_MMD_ADDR_DATA_REG, val); |
| } |
| |
| /* |
| * MT7530 Internal Register Address Bits |
| * ------------------------------------------------------------------- |
| * | 15 14 13 12 11 10 9 8 7 6 | 5 4 3 2 | 1 0 | |
| * |----------------------------------------|---------------|--------| |
| * | Page Address | Reg Address | Unused | |
| * ------------------------------------------------------------------- |
| */ |
| |
| static int mt753x_reg_read(struct mtk_eth_priv *priv, u32 reg, u32 *data) |
| { |
| int ret, low_word, high_word; |
| |
| /* Write page address */ |
| ret = mtk_mii_write(priv, priv->mt753x_smi_addr, 0x1f, reg >> 6); |
| if (ret) |
| return ret; |
| |
| /* Read low word */ |
| low_word = mtk_mii_read(priv, priv->mt753x_smi_addr, (reg >> 2) & 0xf); |
| if (low_word < 0) |
| return low_word; |
| |
| /* Read high word */ |
| high_word = mtk_mii_read(priv, priv->mt753x_smi_addr, 0x10); |
| if (high_word < 0) |
| return high_word; |
| |
| if (data) |
| *data = ((u32)high_word << 16) | (low_word & 0xffff); |
| |
| return 0; |
| } |
| |
| static int mt753x_reg_write(struct mtk_eth_priv *priv, u32 reg, u32 data) |
| { |
| int ret; |
| |
| /* Write page address */ |
| ret = mtk_mii_write(priv, priv->mt753x_smi_addr, 0x1f, reg >> 6); |
| if (ret) |
| return ret; |
| |
| /* Write low word */ |
| ret = mtk_mii_write(priv, priv->mt753x_smi_addr, (reg >> 2) & 0xf, |
| data & 0xffff); |
| if (ret) |
| return ret; |
| |
| /* Write high word */ |
| return mtk_mii_write(priv, priv->mt753x_smi_addr, 0x10, data >> 16); |
| } |
| |
| static void mt753x_reg_rmw(struct mtk_eth_priv *priv, u32 reg, u32 clr, |
| u32 set) |
| { |
| u32 val; |
| |
| mt753x_reg_read(priv, reg, &val); |
| val &= ~clr; |
| val |= set; |
| mt753x_reg_write(priv, reg, val); |
| } |
| |
| /* Indirect MDIO clause 22/45 access */ |
| static int mt7531_mii_rw(struct mtk_eth_priv *priv, int phy, int reg, u16 data, |
| u32 cmd, u32 st) |
| { |
| ulong timeout; |
| u32 val, timeout_ms; |
| int ret = 0; |
| |
| val = (st << MDIO_ST_S) | |
| ((cmd << MDIO_CMD_S) & MDIO_CMD_M) | |
| ((phy << MDIO_PHY_ADDR_S) & MDIO_PHY_ADDR_M) | |
| ((reg << MDIO_REG_ADDR_S) & MDIO_REG_ADDR_M); |
| |
| if (cmd == MDIO_CMD_WRITE || cmd == MDIO_CMD_ADDR) |
| val |= data & MDIO_RW_DATA_M; |
| |
| mt753x_reg_write(priv, MT7531_PHY_IAC, val | PHY_ACS_ST); |
| |
| timeout_ms = 100; |
| timeout = get_timer(0); |
| while (1) { |
| mt753x_reg_read(priv, MT7531_PHY_IAC, &val); |
| |
| if ((val & PHY_ACS_ST) == 0) |
| break; |
| |
| if (get_timer(timeout) > timeout_ms) |
| return -ETIMEDOUT; |
| } |
| |
| if (cmd == MDIO_CMD_READ || cmd == MDIO_CMD_READ_C45) { |
| mt753x_reg_read(priv, MT7531_PHY_IAC, &val); |
| ret = val & MDIO_RW_DATA_M; |
| } |
| |
| return ret; |
| } |
| |
| static int mt7531_mii_ind_read(struct mtk_eth_priv *priv, u8 phy, u8 reg) |
| { |
| u8 phy_addr; |
| |
| if (phy >= MT753X_NUM_PHYS) |
| return -EINVAL; |
| |
| phy_addr = MT753X_PHY_ADDR(priv->mt753x_phy_base, phy); |
| |
| return mt7531_mii_rw(priv, phy_addr, reg, 0, MDIO_CMD_READ, |
| MDIO_ST_C22); |
| } |
| |
| static int mt7531_mii_ind_write(struct mtk_eth_priv *priv, u8 phy, u8 reg, |
| u16 val) |
| { |
| u8 phy_addr; |
| |
| if (phy >= MT753X_NUM_PHYS) |
| return -EINVAL; |
| |
| phy_addr = MT753X_PHY_ADDR(priv->mt753x_phy_base, phy); |
| |
| return mt7531_mii_rw(priv, phy_addr, reg, val, MDIO_CMD_WRITE, |
| MDIO_ST_C22); |
| } |
| |
| int mt7531_mmd_ind_read(struct mtk_eth_priv *priv, u8 addr, u8 devad, u16 reg) |
| { |
| u8 phy_addr; |
| int ret; |
| |
| if (addr >= MT753X_NUM_PHYS) |
| return -EINVAL; |
| |
| phy_addr = MT753X_PHY_ADDR(priv->mt753x_phy_base, addr); |
| |
| ret = mt7531_mii_rw(priv, phy_addr, devad, reg, MDIO_CMD_ADDR, |
| MDIO_ST_C45); |
| if (ret) |
| return ret; |
| |
| return mt7531_mii_rw(priv, phy_addr, devad, 0, MDIO_CMD_READ_C45, |
| MDIO_ST_C45); |
| } |
| |
| static int mt7531_mmd_ind_write(struct mtk_eth_priv *priv, u8 addr, u8 devad, |
| u16 reg, u16 val) |
| { |
| u8 phy_addr; |
| int ret; |
| |
| if (addr >= MT753X_NUM_PHYS) |
| return 0; |
| |
| phy_addr = MT753X_PHY_ADDR(priv->mt753x_phy_base, addr); |
| |
| ret = mt7531_mii_rw(priv, phy_addr, devad, reg, MDIO_CMD_ADDR, |
| MDIO_ST_C45); |
| if (ret) |
| return ret; |
| |
| return mt7531_mii_rw(priv, phy_addr, devad, val, MDIO_CMD_WRITE, |
| MDIO_ST_C45); |
| } |
| |
| static int mtk_mdio_read(struct mii_dev *bus, int addr, int devad, int reg) |
| { |
| struct mtk_eth_priv *priv = bus->priv; |
| |
| if (devad < 0) |
| return priv->mii_read(priv, addr, reg); |
| else |
| return priv->mmd_read(priv, addr, devad, reg); |
| } |
| |
| static int mtk_mdio_write(struct mii_dev *bus, int addr, int devad, int reg, |
| u16 val) |
| { |
| struct mtk_eth_priv *priv = bus->priv; |
| |
| if (devad < 0) |
| return priv->mii_write(priv, addr, reg, val); |
| else |
| return priv->mmd_write(priv, addr, devad, reg, val); |
| } |
| |
| static int mtk_mdio_register(struct udevice *dev) |
| { |
| struct mtk_eth_priv *priv = dev_get_priv(dev); |
| struct mii_dev *mdio_bus = mdio_alloc(); |
| int ret; |
| |
| if (!mdio_bus) |
| return -ENOMEM; |
| |
| /* Assign MDIO access APIs according to the switch/phy */ |
| switch (priv->sw) { |
| case SW_MT7530: |
| priv->mii_read = mtk_mii_read; |
| priv->mii_write = mtk_mii_write; |
| priv->mmd_read = mtk_mmd_ind_read; |
| priv->mmd_write = mtk_mmd_ind_write; |
| break; |
| case SW_MT7531: |
| priv->mii_read = mt7531_mii_ind_read; |
| priv->mii_write = mt7531_mii_ind_write; |
| priv->mmd_read = mt7531_mmd_ind_read; |
| priv->mmd_write = mt7531_mmd_ind_write; |
| break; |
| default: |
| priv->mii_read = mtk_mii_read; |
| priv->mii_write = mtk_mii_write; |
| priv->mmd_read = mtk_mmd_read; |
| priv->mmd_write = mtk_mmd_write; |
| } |
| |
| mdio_bus->read = mtk_mdio_read; |
| mdio_bus->write = mtk_mdio_write; |
| snprintf(mdio_bus->name, sizeof(mdio_bus->name), dev->name); |
| |
| mdio_bus->priv = (void *)priv; |
| |
| ret = mdio_register(mdio_bus); |
| |
| if (ret) |
| return ret; |
| |
| priv->mdio_bus = mdio_bus; |
| |
| return 0; |
| } |
| |
| static int mt753x_core_reg_read(struct mtk_eth_priv *priv, u32 reg) |
| { |
| u8 phy_addr = MT753X_PHY_ADDR(priv->mt753x_phy_base, 0); |
| |
| return priv->mmd_read(priv, phy_addr, 0x1f, reg); |
| } |
| |
| static void mt753x_core_reg_write(struct mtk_eth_priv *priv, u32 reg, u32 val) |
| { |
| u8 phy_addr = MT753X_PHY_ADDR(priv->mt753x_phy_base, 0); |
| |
| priv->mmd_write(priv, phy_addr, 0x1f, reg, val); |
| } |
| |
| static int mt7530_pad_clk_setup(struct mtk_eth_priv *priv, int mode) |
| { |
| u32 ncpo1, ssc_delta; |
| |
| switch (mode) { |
| case PHY_INTERFACE_MODE_RGMII: |
| ncpo1 = 0x0c80; |
| ssc_delta = 0x87; |
| break; |
| default: |
| printf("error: xMII mode %d not supported\n", mode); |
| return -EINVAL; |
| } |
| |
| /* Disable MT7530 core clock */ |
| mt753x_core_reg_write(priv, CORE_TRGMII_GSW_CLK_CG, 0); |
| |
| /* Disable MT7530 PLL */ |
| mt753x_core_reg_write(priv, CORE_GSWPLL_GRP1, |
| (2 << RG_GSWPLL_POSDIV_200M_S) | |
| (32 << RG_GSWPLL_FBKDIV_200M_S)); |
| |
| /* For MT7530 core clock = 500Mhz */ |
| mt753x_core_reg_write(priv, CORE_GSWPLL_GRP2, |
| (1 << RG_GSWPLL_POSDIV_500M_S) | |
| (25 << RG_GSWPLL_FBKDIV_500M_S)); |
| |
| /* Enable MT7530 PLL */ |
| mt753x_core_reg_write(priv, CORE_GSWPLL_GRP1, |
| (2 << RG_GSWPLL_POSDIV_200M_S) | |
| (32 << RG_GSWPLL_FBKDIV_200M_S) | |
| RG_GSWPLL_EN_PRE); |
| |
| udelay(20); |
| |
| mt753x_core_reg_write(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); |
| |
| /* Setup the MT7530 TRGMII Tx Clock */ |
| mt753x_core_reg_write(priv, CORE_PLL_GROUP5, ncpo1); |
| mt753x_core_reg_write(priv, CORE_PLL_GROUP6, 0); |
| mt753x_core_reg_write(priv, CORE_PLL_GROUP10, ssc_delta); |
| mt753x_core_reg_write(priv, CORE_PLL_GROUP11, ssc_delta); |
| mt753x_core_reg_write(priv, CORE_PLL_GROUP4, RG_SYSPLL_DDSFBK_EN | |
| RG_SYSPLL_BIAS_EN | RG_SYSPLL_BIAS_LPF_EN); |
| |
| mt753x_core_reg_write(priv, CORE_PLL_GROUP2, |
| RG_SYSPLL_EN_NORMAL | RG_SYSPLL_VODEN | |
| (1 << RG_SYSPLL_POSDIV_S)); |
| |
| mt753x_core_reg_write(priv, CORE_PLL_GROUP7, |
| RG_LCDDS_PCW_NCPO_CHG | (3 << RG_LCCDS_C_S) | |
| RG_LCDDS_PWDB | RG_LCDDS_ISO_EN); |
| |
| /* Enable MT7530 core clock */ |
| mt753x_core_reg_write(priv, CORE_TRGMII_GSW_CLK_CG, |
| REG_GSWCK_EN | REG_TRGMIICK_EN); |
| |
| return 0; |
| } |
| |
| static int mt7530_setup(struct mtk_eth_priv *priv) |
| { |
| u16 phy_addr, phy_val; |
| u32 val; |
| int i; |
| |
| /* Select 250MHz clk for RGMII mode */ |
| mtk_ethsys_rmw(priv, ETHSYS_CLKCFG0_REG, |
| ETHSYS_TRGMII_CLK_SEL362_5, 0); |
| |
| /* Modify HWTRAP first to allow direct access to internal PHYs */ |
| mt753x_reg_read(priv, HWTRAP_REG, &val); |
| val |= CHG_TRAP; |
| val &= ~C_MDIO_BPS; |
| mt753x_reg_write(priv, MHWTRAP_REG, val); |
| |
| /* Calculate the phy base address */ |
| val = ((val & SMI_ADDR_M) >> SMI_ADDR_S) << 3; |
| priv->mt753x_phy_base = (val | 0x7) + 1; |
| |
| /* Turn off PHYs */ |
| for (i = 0; i < MT753X_NUM_PHYS; i++) { |
| phy_addr = MT753X_PHY_ADDR(priv->mt753x_phy_base, i); |
| phy_val = priv->mii_read(priv, phy_addr, MII_BMCR); |
| phy_val |= BMCR_PDOWN; |
| priv->mii_write(priv, phy_addr, MII_BMCR, phy_val); |
| } |
| |
| /* Force MAC link down before reset */ |
| mt753x_reg_write(priv, PMCR_REG(5), FORCE_MODE); |
| mt753x_reg_write(priv, PMCR_REG(6), FORCE_MODE); |
| |
| /* MT7530 reset */ |
| mt753x_reg_write(priv, SYS_CTRL_REG, SW_SYS_RST | SW_REG_RST); |
| udelay(100); |
| |
| val = (IPG_96BIT_WITH_SHORT_IPG << IPG_CFG_S) | |
| MAC_MODE | FORCE_MODE | |
| MAC_TX_EN | MAC_RX_EN | |
| BKOFF_EN | BACKPR_EN | |
| (SPEED_1000M << FORCE_SPD_S) | |
| FORCE_DPX | FORCE_LINK; |
| |
| /* MT7530 Port6: Forced 1000M/FD, FC disabled */ |
| mt753x_reg_write(priv, PMCR_REG(6), val); |
| |
| /* MT7530 Port5: Forced link down */ |
| mt753x_reg_write(priv, PMCR_REG(5), FORCE_MODE); |
| |
| /* MT7530 Port6: Set to RGMII */ |
| mt753x_reg_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_M, P6_INTF_MODE_RGMII); |
| |
| /* Hardware Trap: Enable Port6, Disable Port5 */ |
| mt753x_reg_read(priv, HWTRAP_REG, &val); |
| val |= CHG_TRAP | LOOPDET_DIS | P5_INTF_DIS | |
| (P5_INTF_SEL_GMAC5 << P5_INTF_SEL_S) | |
| (P5_INTF_MODE_RGMII << P5_INTF_MODE_S); |
| val &= ~(C_MDIO_BPS | P6_INTF_DIS); |
| mt753x_reg_write(priv, MHWTRAP_REG, val); |
| |
| /* Setup switch core pll */ |
| mt7530_pad_clk_setup(priv, priv->phy_interface); |
| |
| /* Lower Tx Driving for TRGMII path */ |
| for (i = 0 ; i < NUM_TRGMII_CTRL ; i++) |
| mt753x_reg_write(priv, MT7530_TRGMII_TD_ODT(i), |
| (8 << TD_DM_DRVP_S) | (8 << TD_DM_DRVN_S)); |
| |
| for (i = 0 ; i < NUM_TRGMII_CTRL; i++) |
| mt753x_reg_rmw(priv, MT7530_TRGMII_RD(i), RD_TAP_M, 16); |
| |
| /* Turn on PHYs */ |
| for (i = 0; i < MT753X_NUM_PHYS; i++) { |
| phy_addr = MT753X_PHY_ADDR(priv->mt753x_phy_base, i); |
| phy_val = priv->mii_read(priv, phy_addr, MII_BMCR); |
| phy_val &= ~BMCR_PDOWN; |
| priv->mii_write(priv, phy_addr, MII_BMCR, phy_val); |
| } |
| |
| return 0; |
| } |
| |
| static void mt7531_core_pll_setup(struct mtk_eth_priv *priv, int mcm) |
| { |
| /* Step 1 : Disable MT7531 COREPLL */ |
| mt753x_reg_rmw(priv, MT7531_PLLGP_EN, EN_COREPLL, 0); |
| |
| /* Step 2: switch to XTAL output */ |
| mt753x_reg_rmw(priv, MT7531_PLLGP_EN, SW_CLKSW, SW_CLKSW); |
| |
| mt753x_reg_rmw(priv, MT7531_PLLGP_CR0, RG_COREPLL_EN, 0); |
| |
| /* Step 3: disable PLLGP and enable program PLLGP */ |
| mt753x_reg_rmw(priv, MT7531_PLLGP_EN, SW_PLLGP, SW_PLLGP); |
| |
| /* Step 4: program COREPLL output frequency to 500MHz */ |
| mt753x_reg_rmw(priv, MT7531_PLLGP_CR0, RG_COREPLL_POSDIV_M, |
| 2 << RG_COREPLL_POSDIV_S); |
| udelay(25); |
| |
| /* Currently, support XTAL 25Mhz only */ |
| mt753x_reg_rmw(priv, MT7531_PLLGP_CR0, RG_COREPLL_SDM_PCW_M, |
| 0x140000 << RG_COREPLL_SDM_PCW_S); |
| |
| /* Set feedback divide ratio update signal to high */ |
| mt753x_reg_rmw(priv, MT7531_PLLGP_CR0, RG_COREPLL_SDM_PCW_CHG, |
| RG_COREPLL_SDM_PCW_CHG); |
| |
| /* Wait for at least 16 XTAL clocks */ |
| udelay(10); |
| |
| /* Step 5: set feedback divide ratio update signal to low */ |
| mt753x_reg_rmw(priv, MT7531_PLLGP_CR0, RG_COREPLL_SDM_PCW_CHG, 0); |
| |
| /* add enable 325M clock for SGMII */ |
| mt753x_reg_write(priv, MT7531_ANA_PLLGP_CR5, 0xad0000); |
| |
| /* add enable 250SSC clock for RGMII */ |
| mt753x_reg_write(priv, MT7531_ANA_PLLGP_CR2, 0x4f40000); |
| |
| /*Step 6: Enable MT7531 PLL */ |
| mt753x_reg_rmw(priv, MT7531_PLLGP_CR0, RG_COREPLL_EN, RG_COREPLL_EN); |
| |
| mt753x_reg_rmw(priv, MT7531_PLLGP_EN, EN_COREPLL, EN_COREPLL); |
| |
| udelay(25); |
| } |
| |
| static int mt7531_port_sgmii_init(struct mtk_eth_priv *priv, |
| u32 port) |
| { |
| if (port != 5 && port != 6) { |
| printf("mt7531: port %d is not a SGMII port\n", port); |
| return -EINVAL; |
| } |
| |
| /* Set SGMII GEN2 speed(2.5G) */ |
| mt753x_reg_rmw(priv, MT7531_PHYA_CTRL_SIGNAL3(port), |
| SGMSYS_SPEED_2500, SGMSYS_SPEED_2500); |
| |
| /* Disable SGMII AN */ |
| mt753x_reg_rmw(priv, MT7531_PCS_CONTROL_1(port), |
| SGMII_AN_ENABLE, 0); |
| |
| /* SGMII force mode setting */ |
| mt753x_reg_write(priv, MT7531_SGMII_MODE(port), SGMII_FORCE_MODE); |
| |
| /* Release PHYA power down state */ |
| mt753x_reg_rmw(priv, MT7531_QPHY_PWR_STATE_CTRL(port), |
| SGMII_PHYA_PWD, 0); |
| |
| return 0; |
| } |
| |
| static int mt7531_port_rgmii_init(struct mtk_eth_priv *priv, u32 port) |
| { |
| u32 val; |
| |
| if (port != 5) { |
| printf("error: RGMII mode is not available for port %d\n", |
| port); |
| return -EINVAL; |
| } |
| |
| mt753x_reg_read(priv, MT7531_CLKGEN_CTRL, &val); |
| val |= GP_CLK_EN; |
| val &= ~GP_MODE_M; |
| val |= GP_MODE_RGMII << GP_MODE_S; |
| val |= TXCLK_NO_REVERSE; |
| val |= RXCLK_NO_DELAY; |
| val &= ~CLK_SKEW_IN_M; |
| val |= CLK_SKEW_IN_NO_CHANGE << CLK_SKEW_IN_S; |
| val &= ~CLK_SKEW_OUT_M; |
| val |= CLK_SKEW_OUT_NO_CHANGE << CLK_SKEW_OUT_S; |
| mt753x_reg_write(priv, MT7531_CLKGEN_CTRL, val); |
| |
| return 0; |
| } |
| |
| static void mt7531_phy_setting(struct mtk_eth_priv *priv) |
| { |
| int i; |
| u32 val; |
| |
| for (i = 0; i < MT753X_NUM_PHYS; i++) { |
| /* Enable HW auto downshift */ |
| priv->mii_write(priv, i, 0x1f, 0x1); |
| val = priv->mii_read(priv, i, PHY_EXT_REG_14); |
| val |= PHY_EN_DOWN_SHFIT; |
| priv->mii_write(priv, i, PHY_EXT_REG_14, val); |
| |
| /* PHY link down power saving enable */ |
| val = priv->mii_read(priv, i, PHY_EXT_REG_17); |
| val |= PHY_LINKDOWN_POWER_SAVING_EN; |
| priv->mii_write(priv, i, PHY_EXT_REG_17, val); |
| |
| val = priv->mmd_read(priv, i, 0x1e, PHY_DEV1E_REG_0C6); |
| val &= ~PHY_POWER_SAVING_M; |
| val |= PHY_POWER_SAVING_TX << PHY_POWER_SAVING_S; |
| priv->mmd_write(priv, i, 0x1e, PHY_DEV1E_REG_0C6, val); |
| } |
| } |
| |
| static int mt7531_setup(struct mtk_eth_priv *priv) |
| { |
| u16 phy_addr, phy_val; |
| u32 val; |
| u32 pmcr; |
| u32 port5_sgmii; |
| int i; |
| |
| priv->mt753x_phy_base = (priv->mt753x_smi_addr + 1) & |
| MT753X_SMI_ADDR_MASK; |
| |
| /* Turn off PHYs */ |
| for (i = 0; i < MT753X_NUM_PHYS; i++) { |
| phy_addr = MT753X_PHY_ADDR(priv->mt753x_phy_base, i); |
| phy_val = priv->mii_read(priv, phy_addr, MII_BMCR); |
| phy_val |= BMCR_PDOWN; |
| priv->mii_write(priv, phy_addr, MII_BMCR, phy_val); |
| } |
| |
| /* Force MAC link down before reset */ |
| mt753x_reg_write(priv, PMCR_REG(5), FORCE_MODE_LNK); |
| mt753x_reg_write(priv, PMCR_REG(6), FORCE_MODE_LNK); |
| |
| /* Switch soft reset */ |
| mt753x_reg_write(priv, SYS_CTRL_REG, SW_SYS_RST | SW_REG_RST); |
| udelay(100); |
| |
| /* Enable MDC input Schmitt Trigger */ |
| mt753x_reg_rmw(priv, MT7531_SMT0_IOLB, SMT_IOLB_5_SMI_MDC_EN, |
| SMT_IOLB_5_SMI_MDC_EN); |
| |
| mt7531_core_pll_setup(priv, priv->mcm); |
| |
| mt753x_reg_read(priv, MT7531_TOP_SIG_SR, &val); |
| port5_sgmii = !!(val & PAD_DUAL_SGMII_EN); |
| |
| /* port5 support either RGMII or SGMII, port6 only support SGMII. */ |
| switch (priv->phy_interface) { |
| case PHY_INTERFACE_MODE_RGMII: |
| if (!port5_sgmii) |
| mt7531_port_rgmii_init(priv, 5); |
| break; |
| case PHY_INTERFACE_MODE_SGMII: |
| mt7531_port_sgmii_init(priv, 6); |
| if (port5_sgmii) |
| mt7531_port_sgmii_init(priv, 5); |
| break; |
| default: |
| break; |
| } |
| |
| pmcr = MT7531_FORCE_MODE | |
| (IPG_96BIT_WITH_SHORT_IPG << IPG_CFG_S) | |
| MAC_MODE | MAC_TX_EN | MAC_RX_EN | |
| BKOFF_EN | BACKPR_EN | |
| FORCE_RX_FC | FORCE_TX_FC | |
| (SPEED_1000M << FORCE_SPD_S) | FORCE_DPX | |
| FORCE_LINK; |
| |
| mt753x_reg_write(priv, PMCR_REG(5), pmcr); |
| mt753x_reg_write(priv, PMCR_REG(6), pmcr); |
| |
| /* Turn on PHYs */ |
| for (i = 0; i < MT753X_NUM_PHYS; i++) { |
| phy_addr = MT753X_PHY_ADDR(priv->mt753x_phy_base, i); |
| phy_val = priv->mii_read(priv, phy_addr, MII_BMCR); |
| phy_val &= ~BMCR_PDOWN; |
| priv->mii_write(priv, phy_addr, MII_BMCR, phy_val); |
| } |
| |
| mt7531_phy_setting(priv); |
| |
| /* Enable Internal PHYs */ |
| val = mt753x_core_reg_read(priv, CORE_PLL_GROUP4); |
| val |= MT7531_BYPASS_MODE; |
| val &= ~MT7531_POWER_ON_OFF; |
| mt753x_core_reg_write(priv, CORE_PLL_GROUP4, val); |
| |
| return 0; |
| } |
| |
| int mt753x_switch_init(struct mtk_eth_priv *priv) |
| { |
| int ret; |
| int i; |
| |
| /* Global reset switch */ |
| if (priv->mcm) { |
| reset_assert(&priv->rst_mcm); |
| udelay(1000); |
| reset_deassert(&priv->rst_mcm); |
| mdelay(1000); |
| } else if (dm_gpio_is_valid(&priv->rst_gpio)) { |
| dm_gpio_set_value(&priv->rst_gpio, 0); |
| udelay(1000); |
| dm_gpio_set_value(&priv->rst_gpio, 1); |
| mdelay(1000); |
| } |
| |
| ret = priv->switch_init(priv); |
| if (ret) |
| return ret; |
| |
| /* Set port isolation */ |
| for (i = 0; i < MT753X_NUM_PORTS; i++) { |
| /* Set port matrix mode */ |
| if (i != 6) |
| mt753x_reg_write(priv, PCR_REG(i), |
| (0x40 << PORT_MATRIX_S)); |
| else |
| mt753x_reg_write(priv, PCR_REG(i), |
| (0x3f << PORT_MATRIX_S)); |
| |
| /* Set port mode to user port */ |
| mt753x_reg_write(priv, PVC_REG(i), |
| (0x8100 << STAG_VPID_S) | |
| (VLAN_ATTR_USER << VLAN_ATTR_S)); |
| } |
| |
| return 0; |
| } |
| |
| static void mtk_phy_link_adjust(struct mtk_eth_priv *priv) |
| { |
| u16 lcl_adv = 0, rmt_adv = 0; |
| u8 flowctrl; |
| u32 mcr; |
| |
| mcr = (IPG_96BIT_WITH_SHORT_IPG << IPG_CFG_S) | |
| (MAC_RX_PKT_LEN_1536 << MAC_RX_PKT_LEN_S) | |
| MAC_MODE | FORCE_MODE | |
| MAC_TX_EN | MAC_RX_EN | |
| BKOFF_EN | BACKPR_EN; |
| |
| switch (priv->phydev->speed) { |
| case SPEED_10: |
| mcr |= (SPEED_10M << FORCE_SPD_S); |
| break; |
| case SPEED_100: |
| mcr |= (SPEED_100M << FORCE_SPD_S); |
| break; |
| case SPEED_1000: |
| mcr |= (SPEED_1000M << FORCE_SPD_S); |
| break; |
| }; |
| |
| if (priv->phydev->link) |
| mcr |= FORCE_LINK; |
| |
| if (priv->phydev->duplex) { |
| mcr |= FORCE_DPX; |
| |
| if (priv->phydev->pause) |
| rmt_adv = LPA_PAUSE_CAP; |
| if (priv->phydev->asym_pause) |
| rmt_adv |= LPA_PAUSE_ASYM; |
| |
| if (priv->phydev->advertising & ADVERTISED_Pause) |
| lcl_adv |= ADVERTISE_PAUSE_CAP; |
| if (priv->phydev->advertising & ADVERTISED_Asym_Pause) |
| lcl_adv |= ADVERTISE_PAUSE_ASYM; |
| |
| flowctrl = mii_resolve_flowctrl_fdx(lcl_adv, rmt_adv); |
| |
| if (flowctrl & FLOW_CTRL_TX) |
| mcr |= FORCE_TX_FC; |
| if (flowctrl & FLOW_CTRL_RX) |
| mcr |= FORCE_RX_FC; |
| |
| debug("rx pause %s, tx pause %s\n", |
| flowctrl & FLOW_CTRL_RX ? "enabled" : "disabled", |
| flowctrl & FLOW_CTRL_TX ? "enabled" : "disabled"); |
| } |
| |
| mtk_gmac_write(priv, GMAC_PORT_MCR(priv->gmac_id), mcr); |
| } |
| |
| static int mtk_phy_start(struct mtk_eth_priv *priv) |
| { |
| struct phy_device *phydev = priv->phydev; |
| int ret; |
| |
| ret = phy_startup(phydev); |
| |
| if (ret) { |
| debug("Could not initialize PHY %s\n", phydev->dev->name); |
| return ret; |
| } |
| |
| if (!phydev->link) { |
| debug("%s: link down.\n", phydev->dev->name); |
| return 0; |
| } |
| |
| mtk_phy_link_adjust(priv); |
| |
| debug("Speed: %d, %s duplex%s\n", phydev->speed, |
| (phydev->duplex) ? "full" : "half", |
| (phydev->port == PORT_FIBRE) ? ", fiber mode" : ""); |
| |
| return 0; |
| } |
| |
| static int mtk_phy_probe(struct udevice *dev) |
| { |
| struct mtk_eth_priv *priv = dev_get_priv(dev); |
| struct phy_device *phydev; |
| |
| phydev = phy_connect(priv->mdio_bus, priv->phy_addr, dev, |
| priv->phy_interface); |
| if (!phydev) |
| return -ENODEV; |
| |
| phydev->supported &= PHY_GBIT_FEATURES; |
| phydev->advertising = phydev->supported; |
| |
| priv->phydev = phydev; |
| phy_config(phydev); |
| |
| return 0; |
| } |
| |
| static void mtk_sgmii_init(struct mtk_eth_priv *priv) |
| { |
| /* Set SGMII GEN2 speed(2.5G) */ |
| clrsetbits_le32(priv->sgmii_base + ((priv->soc == SOC_MT7622) ? |
| SGMSYS_GEN2_SPEED : SGMSYS_GEN2_SPEED_V2), |
| SGMSYS_SPEED_2500, SGMSYS_SPEED_2500); |
| |
| /* Disable SGMII AN */ |
| clrsetbits_le32(priv->sgmii_base + SGMSYS_PCS_CONTROL_1, |
| SGMII_AN_ENABLE, 0); |
| |
| /* SGMII force mode setting */ |
| writel(SGMII_FORCE_MODE, priv->sgmii_base + SGMSYS_SGMII_MODE); |
| |
| /* Release PHYA power down state */ |
| clrsetbits_le32(priv->sgmii_base + SGMSYS_QPHY_PWR_STATE_CTRL, |
| SGMII_PHYA_PWD, 0); |
| } |
| |
| static void mtk_mac_init(struct mtk_eth_priv *priv) |
| { |
| int i, ge_mode = 0; |
| u32 mcr; |
| |
| switch (priv->phy_interface) { |
| case PHY_INTERFACE_MODE_RGMII_RXID: |
| case PHY_INTERFACE_MODE_RGMII: |
| ge_mode = GE_MODE_RGMII; |
| break; |
| case PHY_INTERFACE_MODE_SGMII: |
| ge_mode = GE_MODE_RGMII; |
| mtk_ethsys_rmw(priv, ETHSYS_SYSCFG0_REG, SYSCFG0_SGMII_SEL_M, |
| SYSCFG0_SGMII_SEL(priv->gmac_id)); |
| mtk_sgmii_init(priv); |
| break; |
| case PHY_INTERFACE_MODE_MII: |
| case PHY_INTERFACE_MODE_GMII: |
| ge_mode = GE_MODE_MII; |
| break; |
| case PHY_INTERFACE_MODE_RMII: |
| ge_mode = GE_MODE_RMII; |
| break; |
| default: |
| break; |
| } |
| |
| /* set the gmac to the right mode */ |
| mtk_ethsys_rmw(priv, ETHSYS_SYSCFG0_REG, |
| SYSCFG0_GE_MODE_M << SYSCFG0_GE_MODE_S(priv->gmac_id), |
| ge_mode << SYSCFG0_GE_MODE_S(priv->gmac_id)); |
| |
| if (priv->force_mode) { |
| mcr = (IPG_96BIT_WITH_SHORT_IPG << IPG_CFG_S) | |
| (MAC_RX_PKT_LEN_1536 << MAC_RX_PKT_LEN_S) | |
| MAC_MODE | FORCE_MODE | |
| MAC_TX_EN | MAC_RX_EN | |
| BKOFF_EN | BACKPR_EN | |
| FORCE_LINK; |
| |
| switch (priv->speed) { |
| case SPEED_10: |
| mcr |= SPEED_10M << FORCE_SPD_S; |
| break; |
| case SPEED_100: |
| mcr |= SPEED_100M << FORCE_SPD_S; |
| break; |
| case SPEED_1000: |
| mcr |= SPEED_1000M << FORCE_SPD_S; |
| break; |
| } |
| |
| if (priv->duplex) |
| mcr |= FORCE_DPX; |
| |
| mtk_gmac_write(priv, GMAC_PORT_MCR(priv->gmac_id), mcr); |
| } |
| |
| if (priv->soc == SOC_MT7623) { |
| /* Lower Tx Driving for TRGMII path */ |
| for (i = 0 ; i < NUM_TRGMII_CTRL; i++) |
| mtk_gmac_write(priv, GMAC_TRGMII_TD_ODT(i), |
| (8 << TD_DM_DRVP_S) | |
| (8 << TD_DM_DRVN_S)); |
| |
| mtk_gmac_rmw(priv, GMAC_TRGMII_RCK_CTRL, 0, |
| RX_RST | RXC_DQSISEL); |
| mtk_gmac_rmw(priv, GMAC_TRGMII_RCK_CTRL, RX_RST, 0); |
| } |
| } |
| |
| static void mtk_eth_fifo_init(struct mtk_eth_priv *priv) |
| { |
| char *pkt_base = priv->pkt_pool; |
| int i; |
| |
| mtk_pdma_rmw(priv, PDMA_GLO_CFG_REG, 0xffff0000, 0); |
| udelay(500); |
| |
| memset(priv->tx_ring_noc, 0, NUM_TX_DESC * sizeof(struct pdma_txdesc)); |
| memset(priv->rx_ring_noc, 0, NUM_RX_DESC * sizeof(struct pdma_rxdesc)); |
| memset(priv->pkt_pool, 0, TOTAL_PKT_BUF_SIZE); |
| |
| flush_dcache_range((ulong)pkt_base, |
| (ulong)(pkt_base + TOTAL_PKT_BUF_SIZE)); |
| |
| priv->rx_dma_owner_idx0 = 0; |
| priv->tx_cpu_owner_idx0 = 0; |
| |
| for (i = 0; i < NUM_TX_DESC; i++) { |
| priv->tx_ring_noc[i].txd_info2.LS0 = 1; |
| priv->tx_ring_noc[i].txd_info2.DDONE = 1; |
| priv->tx_ring_noc[i].txd_info4.FPORT = priv->gmac_id + 1; |
| |
| priv->tx_ring_noc[i].txd_info1.SDP0 = virt_to_phys(pkt_base); |
| pkt_base += PKTSIZE_ALIGN; |
| } |
| |
| for (i = 0; i < NUM_RX_DESC; i++) { |
| priv->rx_ring_noc[i].rxd_info2.PLEN0 = PKTSIZE_ALIGN; |
| priv->rx_ring_noc[i].rxd_info1.PDP0 = virt_to_phys(pkt_base); |
| pkt_base += PKTSIZE_ALIGN; |
| } |
| |
| mtk_pdma_write(priv, TX_BASE_PTR_REG(0), |
| virt_to_phys(priv->tx_ring_noc)); |
| mtk_pdma_write(priv, TX_MAX_CNT_REG(0), NUM_TX_DESC); |
| mtk_pdma_write(priv, TX_CTX_IDX_REG(0), priv->tx_cpu_owner_idx0); |
| |
| mtk_pdma_write(priv, RX_BASE_PTR_REG(0), |
| virt_to_phys(priv->rx_ring_noc)); |
| mtk_pdma_write(priv, RX_MAX_CNT_REG(0), NUM_RX_DESC); |
| mtk_pdma_write(priv, RX_CRX_IDX_REG(0), NUM_RX_DESC - 1); |
| |
| mtk_pdma_write(priv, PDMA_RST_IDX_REG, RST_DTX_IDX0 | RST_DRX_IDX0); |
| } |
| |
| static int mtk_eth_start(struct udevice *dev) |
| { |
| struct mtk_eth_priv *priv = dev_get_priv(dev); |
| int ret; |
| |
| /* Reset FE */ |
| reset_assert(&priv->rst_fe); |
| udelay(1000); |
| reset_deassert(&priv->rst_fe); |
| mdelay(10); |
| |
| /* Packets forward to PDMA */ |
| mtk_gdma_write(priv, priv->gmac_id, GDMA_IG_CTRL_REG, GDMA_FWD_TO_CPU); |
| |
| if (priv->gmac_id == 0) |
| mtk_gdma_write(priv, 1, GDMA_IG_CTRL_REG, GDMA_FWD_DISCARD); |
| else |
| mtk_gdma_write(priv, 0, GDMA_IG_CTRL_REG, GDMA_FWD_DISCARD); |
| |
| udelay(500); |
| |
| mtk_eth_fifo_init(priv); |
| |
| /* Start PHY */ |
| if (priv->sw == SW_NONE) { |
| ret = mtk_phy_start(priv); |
| if (ret) |
| return ret; |
| } |
| |
| mtk_pdma_rmw(priv, PDMA_GLO_CFG_REG, 0, |
| TX_WB_DDONE | RX_DMA_EN | TX_DMA_EN); |
| udelay(500); |
| |
| return 0; |
| } |
| |
| static void mtk_eth_stop(struct udevice *dev) |
| { |
| struct mtk_eth_priv *priv = dev_get_priv(dev); |
| |
| mtk_pdma_rmw(priv, PDMA_GLO_CFG_REG, |
| TX_WB_DDONE | RX_DMA_EN | TX_DMA_EN, 0); |
| udelay(500); |
| |
| wait_for_bit_le32(priv->fe_base + PDMA_BASE + PDMA_GLO_CFG_REG, |
| RX_DMA_BUSY | TX_DMA_BUSY, 0, 5000, 0); |
| } |
| |
| static int mtk_eth_write_hwaddr(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_plat(dev); |
| struct mtk_eth_priv *priv = dev_get_priv(dev); |
| unsigned char *mac = pdata->enetaddr; |
| u32 macaddr_lsb, macaddr_msb; |
| |
| macaddr_msb = ((u32)mac[0] << 8) | (u32)mac[1]; |
| macaddr_lsb = ((u32)mac[2] << 24) | ((u32)mac[3] << 16) | |
| ((u32)mac[4] << 8) | (u32)mac[5]; |
| |
| mtk_gdma_write(priv, priv->gmac_id, GDMA_MAC_MSB_REG, macaddr_msb); |
| mtk_gdma_write(priv, priv->gmac_id, GDMA_MAC_LSB_REG, macaddr_lsb); |
| |
| return 0; |
| } |
| |
| static int mtk_eth_send(struct udevice *dev, void *packet, int length) |
| { |
| struct mtk_eth_priv *priv = dev_get_priv(dev); |
| u32 idx = priv->tx_cpu_owner_idx0; |
| void *pkt_base; |
| |
| if (!priv->tx_ring_noc[idx].txd_info2.DDONE) { |
| debug("mtk-eth: TX DMA descriptor ring is full\n"); |
| return -EPERM; |
| } |
| |
| pkt_base = (void *)phys_to_virt(priv->tx_ring_noc[idx].txd_info1.SDP0); |
| memcpy(pkt_base, packet, length); |
| flush_dcache_range((ulong)pkt_base, (ulong)pkt_base + |
| roundup(length, ARCH_DMA_MINALIGN)); |
| |
| priv->tx_ring_noc[idx].txd_info2.SDL0 = length; |
| priv->tx_ring_noc[idx].txd_info2.DDONE = 0; |
| |
| priv->tx_cpu_owner_idx0 = (priv->tx_cpu_owner_idx0 + 1) % NUM_TX_DESC; |
| mtk_pdma_write(priv, TX_CTX_IDX_REG(0), priv->tx_cpu_owner_idx0); |
| |
| return 0; |
| } |
| |
| static int mtk_eth_recv(struct udevice *dev, int flags, uchar **packetp) |
| { |
| struct mtk_eth_priv *priv = dev_get_priv(dev); |
| u32 idx = priv->rx_dma_owner_idx0; |
| uchar *pkt_base; |
| u32 length; |
| |
| if (!priv->rx_ring_noc[idx].rxd_info2.DDONE) { |
| debug("mtk-eth: RX DMA descriptor ring is empty\n"); |
| return -EAGAIN; |
| } |
| |
| length = priv->rx_ring_noc[idx].rxd_info2.PLEN0; |
| pkt_base = (void *)phys_to_virt(priv->rx_ring_noc[idx].rxd_info1.PDP0); |
| invalidate_dcache_range((ulong)pkt_base, (ulong)pkt_base + |
| roundup(length, ARCH_DMA_MINALIGN)); |
| |
| if (packetp) |
| *packetp = pkt_base; |
| |
| return length; |
| } |
| |
| static int mtk_eth_free_pkt(struct udevice *dev, uchar *packet, int length) |
| { |
| struct mtk_eth_priv *priv = dev_get_priv(dev); |
| u32 idx = priv->rx_dma_owner_idx0; |
| |
| priv->rx_ring_noc[idx].rxd_info2.DDONE = 0; |
| priv->rx_ring_noc[idx].rxd_info2.LS0 = 0; |
| priv->rx_ring_noc[idx].rxd_info2.PLEN0 = PKTSIZE_ALIGN; |
| |
| mtk_pdma_write(priv, RX_CRX_IDX_REG(0), idx); |
| priv->rx_dma_owner_idx0 = (priv->rx_dma_owner_idx0 + 1) % NUM_RX_DESC; |
| |
| return 0; |
| } |
| |
| static int mtk_eth_probe(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_plat(dev); |
| struct mtk_eth_priv *priv = dev_get_priv(dev); |
| ulong iobase = pdata->iobase; |
| int ret; |
| |
| /* Frame Engine Register Base */ |
| priv->fe_base = (void *)iobase; |
| |
| /* GMAC Register Base */ |
| priv->gmac_base = (void *)(iobase + GMAC_BASE); |
| |
| /* MDIO register */ |
| ret = mtk_mdio_register(dev); |
| if (ret) |
| return ret; |
| |
| /* Prepare for tx/rx rings */ |
| priv->tx_ring_noc = (struct pdma_txdesc *) |
| noncached_alloc(sizeof(struct pdma_txdesc) * NUM_TX_DESC, |
| ARCH_DMA_MINALIGN); |
| priv->rx_ring_noc = (struct pdma_rxdesc *) |
| noncached_alloc(sizeof(struct pdma_rxdesc) * NUM_RX_DESC, |
| ARCH_DMA_MINALIGN); |
| |
| /* Set MAC mode */ |
| mtk_mac_init(priv); |
| |
| /* Probe phy if switch is not specified */ |
| if (priv->sw == SW_NONE) |
| return mtk_phy_probe(dev); |
| |
| /* Initialize switch */ |
| return mt753x_switch_init(priv); |
| } |
| |
| static int mtk_eth_remove(struct udevice *dev) |
| { |
| struct mtk_eth_priv *priv = dev_get_priv(dev); |
| |
| /* MDIO unregister */ |
| mdio_unregister(priv->mdio_bus); |
| mdio_free(priv->mdio_bus); |
| |
| /* Stop possibly started DMA */ |
| mtk_eth_stop(dev); |
| |
| return 0; |
| } |
| |
| static int mtk_eth_of_to_plat(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_plat(dev); |
| struct mtk_eth_priv *priv = dev_get_priv(dev); |
| struct ofnode_phandle_args args; |
| struct regmap *regmap; |
| const char *str; |
| ofnode subnode; |
| int ret; |
| |
| priv->soc = dev_get_driver_data(dev); |
| |
| pdata->iobase = dev_read_addr(dev); |
| |
| /* get corresponding ethsys phandle */ |
| ret = dev_read_phandle_with_args(dev, "mediatek,ethsys", NULL, 0, 0, |
| &args); |
| if (ret) |
| return ret; |
| |
| regmap = syscon_node_to_regmap(args.node); |
| if (IS_ERR(regmap)) |
| return PTR_ERR(regmap); |
| |
| priv->ethsys_base = regmap_get_range(regmap, 0); |
| if (!priv->ethsys_base) { |
| dev_err(dev, "Unable to find ethsys\n"); |
| return -ENODEV; |
| } |
| |
| /* Reset controllers */ |
| ret = reset_get_by_name(dev, "fe", &priv->rst_fe); |
| if (ret) { |
| printf("error: Unable to get reset ctrl for frame engine\n"); |
| return ret; |
| } |
| |
| priv->gmac_id = dev_read_u32_default(dev, "mediatek,gmac-id", 0); |
| |
| /* Interface mode is required */ |
| pdata->phy_interface = dev_read_phy_mode(dev); |
| priv->phy_interface = pdata->phy_interface; |
| if (pdata->phy_interface == PHY_INTERFACE_MODE_NA) { |
| printf("error: phy-mode is not set\n"); |
| return -EINVAL; |
| } |
| |
| /* Force mode or autoneg */ |
| subnode = ofnode_find_subnode(dev_ofnode(dev), "fixed-link"); |
| if (ofnode_valid(subnode)) { |
| priv->force_mode = 1; |
| priv->speed = ofnode_read_u32_default(subnode, "speed", 0); |
| priv->duplex = ofnode_read_bool(subnode, "full-duplex"); |
| |
| if (priv->speed != SPEED_10 && priv->speed != SPEED_100 && |
| priv->speed != SPEED_1000) { |
| printf("error: no valid speed set in fixed-link\n"); |
| return -EINVAL; |
| } |
| } |
| |
| if (priv->phy_interface == PHY_INTERFACE_MODE_SGMII) { |
| /* get corresponding sgmii phandle */ |
| ret = dev_read_phandle_with_args(dev, "mediatek,sgmiisys", |
| NULL, 0, 0, &args); |
| if (ret) |
| return ret; |
| |
| regmap = syscon_node_to_regmap(args.node); |
| |
| if (IS_ERR(regmap)) |
| return PTR_ERR(regmap); |
| |
| priv->sgmii_base = regmap_get_range(regmap, 0); |
| |
| if (!priv->sgmii_base) { |
| dev_err(dev, "Unable to find sgmii\n"); |
| return -ENODEV; |
| } |
| } |
| |
| /* check for switch first, otherwise phy will be used */ |
| priv->sw = SW_NONE; |
| priv->switch_init = NULL; |
| str = dev_read_string(dev, "mediatek,switch"); |
| |
| if (str) { |
| if (!strcmp(str, "mt7530")) { |
| priv->sw = SW_MT7530; |
| priv->switch_init = mt7530_setup; |
| priv->mt753x_smi_addr = MT753X_DFL_SMI_ADDR; |
| } else if (!strcmp(str, "mt7531")) { |
| priv->sw = SW_MT7531; |
| priv->switch_init = mt7531_setup; |
| priv->mt753x_smi_addr = MT753X_DFL_SMI_ADDR; |
| } else { |
| printf("error: unsupported switch\n"); |
| return -EINVAL; |
| } |
| |
| priv->mcm = dev_read_bool(dev, "mediatek,mcm"); |
| if (priv->mcm) { |
| ret = reset_get_by_name(dev, "mcm", &priv->rst_mcm); |
| if (ret) { |
| printf("error: no reset ctrl for mcm\n"); |
| return ret; |
| } |
| } else { |
| gpio_request_by_name(dev, "reset-gpios", 0, |
| &priv->rst_gpio, GPIOD_IS_OUT); |
| } |
| } else { |
| ret = dev_read_phandle_with_args(dev, "phy-handle", NULL, 0, |
| 0, &args); |
| if (ret) { |
| printf("error: phy-handle is not specified\n"); |
| return ret; |
| } |
| |
| priv->phy_addr = ofnode_read_s32_default(args.node, "reg", -1); |
| if (priv->phy_addr < 0) { |
| printf("error: phy address is not specified\n"); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static const struct udevice_id mtk_eth_ids[] = { |
| { .compatible = "mediatek,mt7629-eth", .data = SOC_MT7629 }, |
| { .compatible = "mediatek,mt7623-eth", .data = SOC_MT7623 }, |
| { .compatible = "mediatek,mt7622-eth", .data = SOC_MT7622 }, |
| {} |
| }; |
| |
| static const struct eth_ops mtk_eth_ops = { |
| .start = mtk_eth_start, |
| .stop = mtk_eth_stop, |
| .send = mtk_eth_send, |
| .recv = mtk_eth_recv, |
| .free_pkt = mtk_eth_free_pkt, |
| .write_hwaddr = mtk_eth_write_hwaddr, |
| }; |
| |
| U_BOOT_DRIVER(mtk_eth) = { |
| .name = "mtk-eth", |
| .id = UCLASS_ETH, |
| .of_match = mtk_eth_ids, |
| .of_to_plat = mtk_eth_of_to_plat, |
| .plat_auto = sizeof(struct eth_pdata), |
| .probe = mtk_eth_probe, |
| .remove = mtk_eth_remove, |
| .ops = &mtk_eth_ops, |
| .priv_auto = sizeof(struct mtk_eth_priv), |
| .flags = DM_FLAG_ALLOC_PRIV_DMA, |
| }; |