blob: db6ad99efea10da9a5f07dd33034dc498aad7d6d [file] [log] [blame]
Stefan Roesea4884832014-10-22 12:13:19 +02001/*
2 * Copyright (C) 2014 Stefan Roese <sr@denx.de>
3 *
4 * SPDX-License-Identifier: GPL-2.0+
5 */
6
7#include <common.h>
8#include <miiphy.h>
9#include <asm/io.h>
10#include <asm/arch/cpu.h>
11#include <asm/arch/soc.h>
12#include <linux/mbus.h>
13
Stefan Roese29b103c2015-04-20 09:28:12 +020014#include "../drivers/ddr/marvell/axp/ddr3_hw_training.h"
15#include "../arch/arm/mach-mvebu/serdes/axp/high_speed_env_spec.h"
Stefan Roesee7778ec2015-01-19 11:33:47 +010016
Stefan Roesea4884832014-10-22 12:13:19 +020017DECLARE_GLOBAL_DATA_PTR;
18
19/* Base addresses for the external device chip selects */
20#define DEV_CS0_BASE 0xe0000000
21#define DEV_CS1_BASE 0xe1000000
22#define DEV_CS2_BASE 0xe2000000
23#define DEV_CS3_BASE 0xe3000000
24
Stefan Roesee7778ec2015-01-19 11:33:47 +010025/* DDR3 static configuration */
26MV_DRAM_MC_INIT ddr3_b0_maxbcm[MV_MAX_DDR3_STATIC_SIZE] = {
27 {0x00001400, 0x7301CC30}, /* DDR SDRAM Configuration Register */
28 {0x00001404, 0x30000820}, /* Dunit Control Low Register */
29 {0x00001408, 0x5515BAAB}, /* DDR SDRAM Timing (Low) Register */
30 {0x0000140C, 0x38DA3F97}, /* DDR SDRAM Timing (High) Register */
31 {0x00001410, 0x20100005}, /* DDR SDRAM Address Control Register */
32 {0x00001414, 0x0000F3FF}, /* DDR SDRAM Open Pages Control Reg */
33 {0x00001418, 0x00000e00}, /* DDR SDRAM Operation Register */
34 {0x0000141C, 0x00000672}, /* DDR SDRAM Mode Register */
35 {0x00001420, 0x00000004}, /* DDR SDRAM Extended Mode Register */
36 {0x00001424, 0x0000F3FF}, /* Dunit Control High Register */
37 {0x00001428, 0x0011A940}, /* Dunit Control High Register */
38 {0x0000142C, 0x014C5134}, /* Dunit Control High Register */
39 {0x0000147C, 0x0000D771},
40
41 {0x00001494, 0x00010000}, /* DDR SDRAM ODT Control (Low) Reg */
42 {0x0000149C, 0x00000001}, /* DDR Dunit ODT Control Register */
43 {0x000014A0, 0x00000001},
44 {0x000014A8, 0x00000101},
45
46 /* Recommended Settings from Marvell for 4 x 16 bit devices: */
47 {0x000014C0, 0x192424C9}, /* DRAM addr and Ctrl Driving Strenght*/
48 {0x000014C4, 0xAAA24C9}, /* DRAM Data and DQS Driving Strenght */
49
50 /*
51 * DO NOT Modify - Open Mbus Window - 2G - Mbus is required for the
52 * training sequence
53 */
54 {0x000200e8, 0x3FFF0E01},
55 {0x00020184, 0x3FFFFFE0}, /* Close fast path Window to - 2G */
56
57 {0x0001504, 0x3FFFFFE1}, /* CS0 Size */
58 {0x000150C, 0x00000000}, /* CS1 Size */
59 {0x0001514, 0x00000000}, /* CS2 Size */
60 {0x000151C, 0x00000000}, /* CS3 Size */
61
62 {0x0020220, 0x00000007}, /* Reserved */
63
64 {0x00001538, 0x0000000B}, /* Read Data Sample Delays Register */
65 {0x0000153C, 0x0000000B}, /* Read Data Ready Delay Register */
66
67 {0x000015D0, 0x00000670}, /* MR0 */
68 {0x000015D4, 0x00000044}, /* MR1 */
69 {0x000015D8, 0x00000018}, /* MR2 */
70 {0x000015DC, 0x00000000}, /* MR3 */
71 {0x000015E0, 0x00000001},
72 {0x000015E4, 0x00203c18}, /* ZQDS Configuration Register */
73 {0x000015EC, 0xF800A225}, /* DDR PHY */
74
75 {0x0, 0x0}
76};
77
78MV_DRAM_MODES maxbcm_ddr_modes[MV_DDR3_MODES_NUMBER] = {
79 {"maxbcm_1600-800", 0xB, 0x5, 0x0, A0, ddr3_b0_maxbcm, NULL},
80};
81
82extern MV_SERDES_CHANGE_M_PHY serdes_change_m_phy[];
83
84/* MAXBCM: SERDES 0-4 PCIE, Serdes 7 = SGMII 0, all others = unconnected */
85MV_BIN_SERDES_CFG maxbcm_serdes_cfg[] = {
86 { MV_PEX_ROOT_COMPLEX, 0x20011111, 0x00000000,
87 { PEX_BUS_MODE_X1, PEX_BUS_MODE_X1, PEX_BUS_DISABLED,
88 PEX_BUS_DISABLED },
89 0x1f, serdes_change_m_phy
90 }
91};
92
93MV_DRAM_MODES *ddr3_get_static_ddr_mode(void)
94{
95 /* Only one mode supported for this board */
96 return &maxbcm_ddr_modes[0];
97}
98
99MV_BIN_SERDES_CFG *board_serdes_cfg_get(u8 pex_mode)
100{
101 return &maxbcm_serdes_cfg[0];
102}
Stefan Roesea4884832014-10-22 12:13:19 +0200103
104int board_early_init_f(void)
105{
106 /*
107 * Don't configure MPP (pin multiplexing) and GPIO here,
108 * its already done in bin_hdr
109 */
110
111 /*
112 * Setup some board specific mbus address windows
113 */
114 mbus_dt_setup_win(&mbus_state, DEV_CS0_BASE, 16 << 20,
115 CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS0);
116 mbus_dt_setup_win(&mbus_state, DEV_CS1_BASE, 16 << 20,
117 CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS1);
118 mbus_dt_setup_win(&mbus_state, DEV_CS2_BASE, 16 << 20,
119 CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS2);
120 mbus_dt_setup_win(&mbus_state, DEV_CS3_BASE, 16 << 20,
121 CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS3);
122
123 return 0;
124}
125
126int board_init(void)
127{
128 /* adress of boot parameters */
129 gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
130
131 return 0;
132}
133
134int checkboard(void)
135{
136 puts("Board: maxBCM\n");
137
138 return 0;
139}
140
Stefan Roesea4884832014-10-22 12:13:19 +0200141/* Configure and enable MV88E6185 switch */
Stefan Roesee3b9c982015-11-19 07:46:15 +0100142int board_phy_config(struct phy_device *phydev)
Stefan Roesea4884832014-10-22 12:13:19 +0200143{
Stefan Roesee3b9c982015-11-19 07:46:15 +0100144 /*
145 * todo:
146 * Fill this with the real setup / config code.
147 * Please see board/Marvell/db-mv784mp-gp/db-mv784mp-gp.c
148 * for details.
149 */
150 printf("88E6185 Initialized\n");
151 return 0;
Stefan Roesea4884832014-10-22 12:13:19 +0200152}