| Sandeep Sheriker Mallikarjun | 83a9f0a | 2019-09-27 13:08:56 +0000 | [diff] [blame] | 1 | CONFIG_ARM=y |
| 2 | CONFIG_ARCH_AT91=y |
| 3 | CONFIG_SYS_TEXT_BASE=0x23f00000 |
| 4 | CONFIG_TARGET_SAM9X60EK=y |
| 5 | CONFIG_SYS_MALLOC_F_LEN=0x2000 |
| 6 | CONFIG_ENV_SIZE=0x4000 |
| 7 | CONFIG_NR_DRAM_BANKS=8 |
| 8 | CONFIG_DEBUG_UART_BOARD_INIT=y |
| 9 | CONFIG_DEBUG_UART_BASE=0xfffff200 |
| 10 | CONFIG_DEBUG_UART_CLOCK=200000000 |
| 11 | CONFIG_DEBUG_UART=y |
| 12 | CONFIG_FIT=y |
| 13 | CONFIG_SD_BOOT=y |
| 14 | CONFIG_BOOTDELAY=3 |
| 15 | CONFIG_USE_BOOTARGS=y |
| 16 | CONFIG_BOOTARGS="mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait" |
| 17 | CONFIG_SYS_CONSOLE_IS_IN_ENV=y |
| 18 | # CONFIG_DISPLAY_BOARDINFO is not set |
| 19 | CONFIG_HUSH_PARSER=y |
| 20 | CONFIG_SYS_PROMPT="U-Boot> " |
| 21 | CONFIG_CMD_BOOTZ=y |
| 22 | CONFIG_CMD_MMC=y |
| 23 | # CONFIG_CMD_SETEXPR is not set |
| 24 | CONFIG_CMD_DHCP=y |
| 25 | CONFIG_CMD_MII=y |
| 26 | CONFIG_CMD_PING=y |
| 27 | CONFIG_CMD_FAT=y |
| 28 | CONFIG_OF_CONTROL=y |
| 29 | CONFIG_DEFAULT_DEVICE_TREE="sam9x60ek" |
| 30 | CONFIG_ENV_IS_IN_FAT=y |
| 31 | CONFIG_ENV_FAT_DEVICE_AND_PART="0:1" |
| 32 | CONFIG_DM=y |
| 33 | CONFIG_CLK=y |
| 34 | CONFIG_CLK_AT91=y |
| 35 | CONFIG_AT91_GENERIC_CLK=y |
| 36 | CONFIG_DM_GPIO=y |
| 37 | CONFIG_AT91_GPIO=y |
| 38 | CONFIG_DM_MMC=y |
| 39 | CONFIG_MMC_SDHCI=y |
| 40 | CONFIG_MMC_SDHCI_ATMEL=y |
| 41 | CONFIG_PHY_MICREL=y |
| 42 | CONFIG_DM_ETH=y |
| 43 | CONFIG_MACB=y |
| 44 | CONFIG_PINCTRL=y |
| 45 | CONFIG_PINCTRL_AT91=y |
| 46 | CONFIG_DM_SERIAL=y |
| 47 | CONFIG_DEBUG_UART_ATMEL=y |
| 48 | CONFIG_DEBUG_UART_ANNOUNCE=y |
| 49 | CONFIG_ATMEL_USART=y |
| 50 | CONFIG_TIMER=y |
| 51 | CONFIG_ATMEL_PIT_TIMER=y |
| Eugen Hristev | 0cf837f | 2019-09-30 07:29:02 +0000 | [diff] [blame^] | 52 | CONFIG_W1=y |
| 53 | CONFIG_W1_GPIO=y |
| 54 | CONFIG_W1_EEPROM=y |
| 55 | CONFIG_W1_EEPROM_DS24XXX=y |
| Sandeep Sheriker Mallikarjun | 83a9f0a | 2019-09-27 13:08:56 +0000 | [diff] [blame] | 56 | CONFIG_OF_LIBFDT_OVERLAY=y |