include/configs/at91sam9260ek.h

/*
 * (C) Copyright 2007-2008
 * Stelian Pop <stelian@popies.net>
 * Lead Tech Design <www.leadtechdesign.com>
 *
 * Configuation settings for the AT91SAM9260EK & AT91SAM9G20EK boards.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * SoC must be defined first, before hardware.h is included.
 * In this case SoC is defined in boards.cfg.
 */
#include <asm/hardware.h>

/*
 * Warning: changing CONFIG_SYS_TEXT_BASE requires
 * adapting the initial boot program.
 * Since the linker has to swallow that define, we must use a pure
 * hex number here!
 */

/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK	32768		/* slow clock xtal */
#define CONFIG_SYS_AT91_MAIN_CLOCK	18432000	/* main clock xtal */

/* Define actual evaluation board type from used processor type */
#ifdef CONFIG_AT91SAM9G20
# define CONFIG_AT91SAM9G20EK	/* It's an Atmel AT91SAM9G20 EK */
#else
# define CONFIG_AT91SAM9260EK	/* It's an Atmel AT91SAM9260 EK */
#endif

/* Misc CPU related */
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT

/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE	1

/*
 * SDRAM: 1 bank, min 32, max 128 MB
 * Initialized before u-boot gets started.
 */
#define CONFIG_NR_DRAM_BANKS		1
#define CONFIG_SYS_SDRAM_BASE		ATMEL_BASE_CS1
#define CONFIG_SYS_SDRAM_SIZE		0x04000000

/*
 * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM,
 * leaving the correct space for initial global data structure above
 * that address while providing maximum stack area below.
 */
#ifdef CONFIG_AT91SAM9XE
# define CONFIG_SYS_INIT_SP_ADDR \
	(ATMEL_BASE_SRAM + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
#else
# define CONFIG_SYS_INIT_SP_ADDR \
	(ATMEL_BASE_SRAM1 + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif

/*
 * The (arm)linux board id set by generic code depending on configured board
 * (see boards.cfg for different boards)
 */
#ifdef CONFIG_AT91SAM9G20
	/* the sam9g20 variants have two different board ids */
# ifdef CONFIG_AT91SAM9G20EK_2MMC
	/* we may be setup for the 2MMC variant of at91sam9g20ek */
#  define CONFIG_MACH_TYPE MACH_TYPE_AT91SAM9G20EK_2MMC
# else
	/* or the normal at91sam9g20ek */
#  define CONFIG_MACH_TYPE MACH_TYPE_AT91SAM9G20EK
# endif
#else
	/* otherwise default to good old at91sam9260ek */
# define CONFIG_MACH_TYPE MACH_TYPE_AT91SAM9260EK
#endif

/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_SYS_NAND_BASE		ATMEL_BASE_CS3
#define CONFIG_SYS_NAND_DBW_8
#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
#define CONFIG_SYS_NAND_ENABLE_PIN	AT91_PIN_PC14
#define CONFIG_SYS_NAND_READY_PIN	AT91_PIN_PC13
#endif

/* USB */
#define CONFIG_USB_ATMEL
#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW		1
#define CONFIG_SYS_USB_OHCI_CPU_INIT		1
#define CONFIG_SYS_USB_OHCI_REGS_BASE		0x00500000	/* AT91SAM9260_UHP_BASE */
#define CONFIG_SYS_USB_OHCI_SLOT_NAME		"at91sam9260"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2

#define CONFIG_SYS_LOAD_ADDR			0x22000000	/* load address */

#define CONFIG_SYS_MEMTEST_START		CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END			0x23e00000

#ifdef CONFIG_SYS_USE_DATAFLASH_CS0

/* bootstrap + u-boot + env + linux in dataflash on CS0 */
#define CONFIG_ENV_OFFSET	0x4200
#define CONFIG_ENV_SIZE		0x4200
#define CONFIG_ENV_SECT_SIZE	0x210
#define CONFIG_ENV_SPI_MAX_HZ	15000000
#define CONFIG_BOOTCOMMAND	"sf probe 0:0; " \
				"sf read 0x22000000 0x84000 0x294000; " \
				"bootm 0x22000000"

#elif CONFIG_SYS_USE_DATAFLASH_CS1

#define CONFIG_ENV_OFFSET	0x4200
#define CONFIG_ENV_SIZE		0x4200
#define CONFIG_ENV_SECT_SIZE	0x210
#define CONFIG_ENV_SPI_MAX_HZ	15000000
#define CONFIG_BOOTCOMMAND	"sf probe 0:1; " \
				"sf read 0x22000000 0x84000 0x294000; " \
				"bootm 0x22000000"

#elif defined(CONFIG_SYS_USE_NANDFLASH)

/* bootstrap + u-boot + env + linux in nandflash */
#define CONFIG_ENV_OFFSET		0x120000
#define CONFIG_ENV_OFFSET_REDUND	0x100000
#define CONFIG_ENV_SIZE		0x20000		/* 1 sector = 128 kB */
#define CONFIG_BOOTCOMMAND	"nand read 0x22000000 0x200000 0x300000; bootm"

#else	/* CONFIG_SYS_USE_MMC */
/* bootstrap + u-boot + env + linux in mmc */
/* For FAT system, most cases it should be in the reserved sector */
#define CONFIG_ENV_OFFSET		0x2000
#define CONFIG_ENV_SIZE			0x1000
#define CONFIG_SYS_MMC_ENV_DEV		0

#define CONFIG_BOOTCOMMAND						\
	"fatload mmc 0:1 0x22000000 uImage; bootm"
#endif

/*
 * Size of malloc() pool
 */
#define CONFIG_SYS_MALLOC_LEN		ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)

#endif