blob: 723892261466d60c364b8362ea00121b0bd3c82a [file] [log] [blame]
wdenkc6097192002-11-03 00:24:07 +00001/*
2 * See file CREDITS for list of people who contributed to this
3 * project.
4 *
5 * This program is free software; you can redistribute it and/or
6 * modify it under the terms of the GNU General Public License as
7 * published by the Free Software Foundation; either version 2 of
8 * the License, or (at your option) any later version.
9 *
10 * This program is distributed in the hope that it will be useful,
11 * but WITHOUT ANY WARRANTY; without even the implied warranty of
12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
13 * GNU General Public License for more details.
14 *
15 * You should have received a copy of the GNU General Public License
16 * along with this program; if not, write to the Free Software
17 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
18 * MA 02111-1307 USA
19 */
20
21#include <common.h>
22
Jon Loeliger07d38a12007-07-09 17:30:01 -050023#if defined(CONFIG_CMD_NET) \
Jon Loeligerd5be43d2007-06-11 19:02:10 -050024 && defined(CONFIG_NET_MULTI) && defined(CONFIG_TULIP)
wdenkc6097192002-11-03 00:24:07 +000025
26#include <malloc.h>
27#include <net.h>
28#include <pci.h>
29
wdenkc6097192002-11-03 00:24:07 +000030#undef DEBUG_SROM
31#undef DEBUG_SROM2
32
33#undef UPDATE_SROM
34
35/* PCI Registers.
36 */
37#define PCI_CFDA_PSM 0x43
38
39#define CFRV_RN 0x000000f0 /* Revision Number */
40
41#define WAKEUP 0x00 /* Power Saving Wakeup */
42#define SLEEP 0x80 /* Power Saving Sleep Mode */
43
44#define DC2114x_BRK 0x0020 /* CFRV break between DC21142 & DC21143 */
45
46/* Ethernet chip registers.
47 */
48#define DE4X5_BMR 0x000 /* Bus Mode Register */
49#define DE4X5_TPD 0x008 /* Transmit Poll Demand Reg */
50#define DE4X5_RRBA 0x018 /* RX Ring Base Address Reg */
51#define DE4X5_TRBA 0x020 /* TX Ring Base Address Reg */
52#define DE4X5_STS 0x028 /* Status Register */
53#define DE4X5_OMR 0x030 /* Operation Mode Register */
54#define DE4X5_SICR 0x068 /* SIA Connectivity Register */
55#define DE4X5_APROM 0x048 /* Ethernet Address PROM */
56
57/* Register bits.
58 */
59#define BMR_SWR 0x00000001 /* Software Reset */
60#define STS_TS 0x00700000 /* Transmit Process State */
61#define STS_RS 0x000e0000 /* Receive Process State */
62#define OMR_ST 0x00002000 /* Start/Stop Transmission Command */
63#define OMR_SR 0x00000002 /* Start/Stop Receive */
64#define OMR_PS 0x00040000 /* Port Select */
65#define OMR_SDP 0x02000000 /* SD Polarity - MUST BE ASSERTED */
66#define OMR_PM 0x00000080 /* Pass All Multicast */
67
68/* Descriptor bits.
69 */
70#define R_OWN 0x80000000 /* Own Bit */
71#define RD_RER 0x02000000 /* Receive End Of Ring */
72#define RD_LS 0x00000100 /* Last Descriptor */
73#define RD_ES 0x00008000 /* Error Summary */
74#define TD_TER 0x02000000 /* Transmit End Of Ring */
75#define T_OWN 0x80000000 /* Own Bit */
76#define TD_LS 0x40000000 /* Last Segment */
77#define TD_FS 0x20000000 /* First Segment */
78#define TD_ES 0x00008000 /* Error Summary */
79#define TD_SET 0x08000000 /* Setup Packet */
80
81/* The EEPROM commands include the alway-set leading bit. */
82#define SROM_WRITE_CMD 5
83#define SROM_READ_CMD 6
84#define SROM_ERASE_CMD 7
85
86#define SROM_HWADD 0x0014 /* Hardware Address offset in SROM */
87#define SROM_RD 0x00004000 /* Read from Boot ROM */
wdenkc935d3b2004-01-03 19:43:48 +000088#define EE_DATA_WRITE 0x04 /* EEPROM chip data in. */
89#define EE_WRITE_0 0x4801
90#define EE_WRITE_1 0x4805
91#define EE_DATA_READ 0x08 /* EEPROM chip data out. */
wdenkc6097192002-11-03 00:24:07 +000092#define SROM_SR 0x00000800 /* Select Serial ROM when set */
93
94#define DT_IN 0x00000004 /* Serial Data In */
95#define DT_CLK 0x00000002 /* Serial ROM Clock */
96#define DT_CS 0x00000001 /* Serial ROM Chip Select */
97
98#define POLL_DEMAND 1
99
wdenk63f34912004-01-02 15:01:32 +0000100#ifdef CONFIG_TULIP_FIX_DAVICOM
101#define RESET_DM9102(dev) {\
102 unsigned long i;\
103 i=INL(dev, 0x0);\
104 udelay(1000);\
105 OUTL(dev, i | BMR_SWR, DE4X5_BMR);\
106 udelay(1000);\
107}
108#else
wdenkc6097192002-11-03 00:24:07 +0000109#define RESET_DE4X5(dev) {\
110 int i;\
111 i=INL(dev, DE4X5_BMR);\
112 udelay(1000);\
113 OUTL(dev, i | BMR_SWR, DE4X5_BMR);\
114 udelay(1000);\
115 OUTL(dev, i, DE4X5_BMR);\
116 udelay(1000);\
117 for (i=0;i<5;i++) {INL(dev, DE4X5_BMR); udelay(10000);}\
118 udelay(1000);\
119}
wdenk63f34912004-01-02 15:01:32 +0000120#endif
wdenkc6097192002-11-03 00:24:07 +0000121
122#define START_DE4X5(dev) {\
123 s32 omr; \
124 omr = INL(dev, DE4X5_OMR);\
125 omr |= OMR_ST | OMR_SR;\
126 OUTL(dev, omr, DE4X5_OMR); /* Enable the TX and/or RX */\
127}
128
129#define STOP_DE4X5(dev) {\
130 s32 omr; \
131 omr = INL(dev, DE4X5_OMR);\
132 omr &= ~(OMR_ST|OMR_SR);\
133 OUTL(dev, omr, DE4X5_OMR); /* Disable the TX and/or RX */ \
134}
135
136#define NUM_RX_DESC PKTBUFSRX
wdenk63f34912004-01-02 15:01:32 +0000137#ifndef CONFIG_TULIP_FIX_DAVICOM
138 #define NUM_TX_DESC 1 /* Number of TX descriptors */
139#else
140 #define NUM_TX_DESC 4
141#endif
wdenkc6097192002-11-03 00:24:07 +0000142#define RX_BUFF_SZ PKTSIZE_ALIGN
143
144#define TOUT_LOOP 1000000
145
146#define SETUP_FRAME_LEN 192
147#define ETH_ALEN 6
148
wdenkc6097192002-11-03 00:24:07 +0000149struct de4x5_desc {
150 volatile s32 status;
151 u32 des1;
152 u32 buf;
153 u32 next;
154};
155
wdenk63f34912004-01-02 15:01:32 +0000156static struct de4x5_desc rx_ring[NUM_RX_DESC] __attribute__ ((aligned(32))); /* RX descriptor ring */
157static struct de4x5_desc tx_ring[NUM_TX_DESC] __attribute__ ((aligned(32))); /* TX descriptor ring */
wdenkc6097192002-11-03 00:24:07 +0000158static int rx_new; /* RX descriptor ring pointer */
159static int tx_new; /* TX descriptor ring pointer */
160
161static char rxRingSize;
162static char txRingSize;
163
wdenkc935d3b2004-01-03 19:43:48 +0000164#if defined(UPDATE_SROM) || !defined(CONFIG_TULIP_FIX_DAVICOM)
wdenkc6097192002-11-03 00:24:07 +0000165static void sendto_srom(struct eth_device* dev, u_int command, u_long addr);
166static int getfrom_srom(struct eth_device* dev, u_long addr);
wdenkc935d3b2004-01-03 19:43:48 +0000167static int do_eeprom_cmd(struct eth_device *dev, u_long ioaddr,int cmd,int cmd_len);
168static int do_read_eeprom(struct eth_device *dev,u_long ioaddr,int location,int addr_len);
169#endif /* UPDATE_SROM || !CONFIG_TULIP_FIX_DAVICOM */
wdenkc6097192002-11-03 00:24:07 +0000170#ifdef UPDATE_SROM
171static int write_srom(struct eth_device *dev, u_long ioaddr, int index, int new_value);
172static void update_srom(struct eth_device *dev, bd_t *bis);
173#endif
wdenkc935d3b2004-01-03 19:43:48 +0000174#ifndef CONFIG_TULIP_FIX_DAVICOM
175static int read_srom(struct eth_device *dev, u_long ioaddr, int index);
wdenkc6097192002-11-03 00:24:07 +0000176static void read_hw_addr(struct eth_device* dev, bd_t * bis);
wdenkc935d3b2004-01-03 19:43:48 +0000177#endif /* CONFIG_TULIP_FIX_DAVICOM */
wdenkc6097192002-11-03 00:24:07 +0000178static void send_setup_frame(struct eth_device* dev, bd_t * bis);
179
180static int dc21x4x_init(struct eth_device* dev, bd_t* bis);
181static int dc21x4x_send(struct eth_device* dev, volatile void *packet, int length);
182static int dc21x4x_recv(struct eth_device* dev);
183static void dc21x4x_halt(struct eth_device* dev);
184#ifdef CONFIG_TULIP_SELECT_MEDIA
185extern void dc21x4x_select_media(struct eth_device* dev);
186#endif
187
wdenk42d1f032003-10-15 23:53:47 +0000188#if defined(CONFIG_E500)
189#define phys_to_bus(a) (a)
190#else
wdenkc6097192002-11-03 00:24:07 +0000191#define phys_to_bus(a) pci_phys_to_mem((pci_dev_t)dev->priv, a)
wdenk42d1f032003-10-15 23:53:47 +0000192#endif
wdenkc6097192002-11-03 00:24:07 +0000193
194static int INL(struct eth_device* dev, u_long addr)
195{
196 return le32_to_cpu(*(volatile u_long *)(addr + dev->iobase));
197}
198
199static void OUTL(struct eth_device* dev, int command, u_long addr)
200{
201 *(volatile u_long *)(addr + dev->iobase) = cpu_to_le32(command);
202}
203
204static struct pci_device_id supported[] = {
205 { PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_TULIP_FAST },
206 { PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_21142 },
wdenk63f34912004-01-02 15:01:32 +0000207#ifdef CONFIG_TULIP_FIX_DAVICOM
208 { PCI_VENDOR_ID_DAVICOM, PCI_DEVICE_ID_DAVICOM_DM9102A },
209#endif
wdenkc6097192002-11-03 00:24:07 +0000210 { }
211};
212
213int dc21x4x_initialize(bd_t *bis)
214{
215 int idx=0;
216 int card_number = 0;
Wolfgang Denk77ddac92005-10-13 16:45:02 +0200217 unsigned int cfrv;
wdenkc6097192002-11-03 00:24:07 +0000218 unsigned char timer;
219 pci_dev_t devbusfn;
220 unsigned int iobase;
221 unsigned short status;
222 struct eth_device* dev;
223
224 while(1) {
225 devbusfn = pci_find_devices(supported, idx++);
226 if (devbusfn == -1) {
227 break;
228 }
229
230 /* Get the chip configuration revision register. */
231 pci_read_config_dword(devbusfn, PCI_REVISION_ID, &cfrv);
232
wdenk63f34912004-01-02 15:01:32 +0000233#ifndef CONFIG_TULIP_FIX_DAVICOM
wdenkc6097192002-11-03 00:24:07 +0000234 if ((cfrv & CFRV_RN) < DC2114x_BRK ) {
235 printf("Error: The chip is not DC21143.\n");
236 continue;
237 }
wdenk63f34912004-01-02 15:01:32 +0000238#endif
wdenkc6097192002-11-03 00:24:07 +0000239
240 pci_read_config_word(devbusfn, PCI_COMMAND, &status);
241 status |=
242#ifdef CONFIG_TULIP_USE_IO
243 PCI_COMMAND_IO |
244#else
245 PCI_COMMAND_MEMORY |
246#endif
247 PCI_COMMAND_MASTER;
248 pci_write_config_word(devbusfn, PCI_COMMAND, status);
249
250 pci_read_config_word(devbusfn, PCI_COMMAND, &status);
251 if (!(status & PCI_COMMAND_IO)) {
252 printf("Error: Can not enable I/O access.\n");
253 continue;
254 }
255
256 if (!(status & PCI_COMMAND_IO)) {
257 printf("Error: Can not enable I/O access.\n");
258 continue;
259 }
260
261 if (!(status & PCI_COMMAND_MASTER)) {
262 printf("Error: Can not enable Bus Mastering.\n");
263 continue;
264 }
265
266 /* Check the latency timer for values >= 0x60. */
267 pci_read_config_byte(devbusfn, PCI_LATENCY_TIMER, &timer);
268
269 if (timer < 0x60) {
270 pci_write_config_byte(devbusfn, PCI_LATENCY_TIMER, 0x60);
271 }
272
273#ifdef CONFIG_TULIP_USE_IO
274 /* read BAR for memory space access */
275 pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_0, &iobase);
276 iobase &= PCI_BASE_ADDRESS_IO_MASK;
277#else
278 /* read BAR for memory space access */
279 pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_1, &iobase);
280 iobase &= PCI_BASE_ADDRESS_MEM_MASK;
281#endif
wdenkc935d3b2004-01-03 19:43:48 +0000282 debug ("dc21x4x: DEC 21142 PCI Device @0x%x\n", iobase);
wdenkc6097192002-11-03 00:24:07 +0000283
284 dev = (struct eth_device*) malloc(sizeof *dev);
285
wdenk63f34912004-01-02 15:01:32 +0000286#ifdef CONFIG_TULIP_FIX_DAVICOM
wdenkc935d3b2004-01-03 19:43:48 +0000287 sprintf(dev->name, "Davicom#%d", card_number);
wdenk63f34912004-01-02 15:01:32 +0000288#else
wdenkc935d3b2004-01-03 19:43:48 +0000289 sprintf(dev->name, "dc21x4x#%d", card_number);
wdenk63f34912004-01-02 15:01:32 +0000290#endif
291
wdenkc6097192002-11-03 00:24:07 +0000292#ifdef CONFIG_TULIP_USE_IO
293 dev->iobase = pci_io_to_phys(devbusfn, iobase);
294#else
295 dev->iobase = pci_mem_to_phys(devbusfn, iobase);
296#endif
297 dev->priv = (void*) devbusfn;
298 dev->init = dc21x4x_init;
299 dev->halt = dc21x4x_halt;
300 dev->send = dc21x4x_send;
301 dev->recv = dc21x4x_recv;
302
303 /* Ensure we're not sleeping. */
304 pci_write_config_byte(devbusfn, PCI_CFDA_PSM, WAKEUP);
305
306 udelay(10 * 1000);
307
wdenk63f34912004-01-02 15:01:32 +0000308#ifndef CONFIG_TULIP_FIX_DAVICOM
wdenkc935d3b2004-01-03 19:43:48 +0000309 read_hw_addr(dev, bis);
wdenk63f34912004-01-02 15:01:32 +0000310#endif
wdenkc6097192002-11-03 00:24:07 +0000311 eth_register(dev);
312
313 card_number++;
314 }
315
316 return card_number;
317}
318
319static int dc21x4x_init(struct eth_device* dev, bd_t* bis)
320{
321 int i;
322 int devbusfn = (int) dev->priv;
323
324 /* Ensure we're not sleeping. */
325 pci_write_config_byte(devbusfn, PCI_CFDA_PSM, WAKEUP);
326
wdenk63f34912004-01-02 15:01:32 +0000327#ifdef CONFIG_TULIP_FIX_DAVICOM
328 RESET_DM9102(dev);
329#else
wdenkc6097192002-11-03 00:24:07 +0000330 RESET_DE4X5(dev);
wdenk63f34912004-01-02 15:01:32 +0000331#endif
wdenkc6097192002-11-03 00:24:07 +0000332
333 if ((INL(dev, DE4X5_STS) & (STS_TS | STS_RS)) != 0) {
334 printf("Error: Cannot reset ethernet controller.\n");
Ben Warren422b1a02008-01-09 18:15:53 -0500335 return -1;
wdenkc6097192002-11-03 00:24:07 +0000336 }
337
338#ifdef CONFIG_TULIP_SELECT_MEDIA
339 dc21x4x_select_media(dev);
340#else
341 OUTL(dev, OMR_SDP | OMR_PS | OMR_PM, DE4X5_OMR);
342#endif
343
344 for (i = 0; i < NUM_RX_DESC; i++) {
345 rx_ring[i].status = cpu_to_le32(R_OWN);
346 rx_ring[i].des1 = cpu_to_le32(RX_BUFF_SZ);
347 rx_ring[i].buf = cpu_to_le32(phys_to_bus((u32) NetRxPackets[i]));
wdenk63f34912004-01-02 15:01:32 +0000348#ifdef CONFIG_TULIP_FIX_DAVICOM
349 rx_ring[i].next = cpu_to_le32(phys_to_bus((u32) &rx_ring[(i+1) % NUM_RX_DESC]));
350#else
wdenkc6097192002-11-03 00:24:07 +0000351 rx_ring[i].next = 0;
wdenk63f34912004-01-02 15:01:32 +0000352#endif
wdenkc6097192002-11-03 00:24:07 +0000353 }
354
355 for (i=0; i < NUM_TX_DESC; i++) {
356 tx_ring[i].status = 0;
357 tx_ring[i].des1 = 0;
358 tx_ring[i].buf = 0;
wdenk63f34912004-01-02 15:01:32 +0000359
360#ifdef CONFIG_TULIP_FIX_DAVICOM
wdenk3a473b22004-01-03 00:43:19 +0000361 tx_ring[i].next = cpu_to_le32(phys_to_bus((u32) &tx_ring[(i+1) % NUM_TX_DESC]));
wdenk63f34912004-01-02 15:01:32 +0000362#else
wdenkc6097192002-11-03 00:24:07 +0000363 tx_ring[i].next = 0;
wdenk63f34912004-01-02 15:01:32 +0000364#endif
wdenkc6097192002-11-03 00:24:07 +0000365 }
366
367 rxRingSize = NUM_RX_DESC;
368 txRingSize = NUM_TX_DESC;
369
370 /* Write the end of list marker to the descriptor lists. */
371 rx_ring[rxRingSize - 1].des1 |= cpu_to_le32(RD_RER);
372 tx_ring[txRingSize - 1].des1 |= cpu_to_le32(TD_TER);
373
374 /* Tell the adapter where the TX/RX rings are located. */
375 OUTL(dev, phys_to_bus((u32) &rx_ring), DE4X5_RRBA);
376 OUTL(dev, phys_to_bus((u32) &tx_ring), DE4X5_TRBA);
377
378 START_DE4X5(dev);
379
380 tx_new = 0;
381 rx_new = 0;
382
383 send_setup_frame(dev, bis);
384
Ben Warren422b1a02008-01-09 18:15:53 -0500385 return 0;
wdenkc6097192002-11-03 00:24:07 +0000386}
387
388static int dc21x4x_send(struct eth_device* dev, volatile void *packet, int length)
389{
390 int status = -1;
391 int i;
392
393 if (length <= 0) {
394 printf("%s: bad packet size: %d\n", dev->name, length);
395 goto Done;
396 }
397
398 for(i = 0; tx_ring[tx_new].status & cpu_to_le32(T_OWN); i++) {
399 if (i >= TOUT_LOOP) {
400 printf("%s: tx error buffer not ready\n", dev->name);
401 goto Done;
402 }
403 }
404
405 tx_ring[tx_new].buf = cpu_to_le32(phys_to_bus((u32) packet));
406 tx_ring[tx_new].des1 = cpu_to_le32(TD_TER | TD_LS | TD_FS | length);
407 tx_ring[tx_new].status = cpu_to_le32(T_OWN);
408
409 OUTL(dev, POLL_DEMAND, DE4X5_TPD);
410
411 for(i = 0; tx_ring[tx_new].status & cpu_to_le32(T_OWN); i++) {
412 if (i >= TOUT_LOOP) {
413 printf(".%s: tx buffer not ready\n", dev->name);
414 goto Done;
415 }
416 }
417
418 if (le32_to_cpu(tx_ring[tx_new].status) & TD_ES) {
419#if 0 /* test-only */
420 printf("TX error status = 0x%08X\n",
wdenkc935d3b2004-01-03 19:43:48 +0000421 le32_to_cpu(tx_ring[tx_new].status));
wdenkc6097192002-11-03 00:24:07 +0000422#endif
wdenk63f34912004-01-02 15:01:32 +0000423 tx_ring[tx_new].status = 0x0;
wdenkc6097192002-11-03 00:24:07 +0000424 goto Done;
425 }
426
427 status = length;
428
429 Done:
wdenk63f34912004-01-02 15:01:32 +0000430 tx_new = (tx_new+1) % NUM_TX_DESC;
wdenkc6097192002-11-03 00:24:07 +0000431 return status;
432}
433
434static int dc21x4x_recv(struct eth_device* dev)
435{
436 s32 status;
437 int length = 0;
438
439 for ( ; ; ) {
440 status = (s32)le32_to_cpu(rx_ring[rx_new].status);
441
442 if (status & R_OWN) {
443 break;
444 }
445
446 if (status & RD_LS) {
447 /* Valid frame status.
448 */
449 if (status & RD_ES) {
450
451 /* There was an error.
452 */
453 printf("RX error status = 0x%08X\n", status);
454 } else {
455 /* A valid frame received.
456 */
457 length = (le32_to_cpu(rx_ring[rx_new].status) >> 16);
458
459 /* Pass the packet up to the protocol
460 * layers.
461 */
462 NetReceive(NetRxPackets[rx_new], length - 4);
463 }
464
465 /* Change buffer ownership for this frame, back
466 * to the adapter.
467 */
468 rx_ring[rx_new].status = cpu_to_le32(R_OWN);
469 }
470
471 /* Update entry information.
472 */
473 rx_new = (rx_new + 1) % rxRingSize;
474 }
475
476 return length;
477}
478
479static void dc21x4x_halt(struct eth_device* dev)
480{
481 int devbusfn = (int) dev->priv;
482
483 STOP_DE4X5(dev);
484 OUTL(dev, 0, DE4X5_SICR);
485
486 pci_write_config_byte(devbusfn, PCI_CFDA_PSM, SLEEP);
487}
488
489static void send_setup_frame(struct eth_device* dev, bd_t *bis)
490{
491 int i;
492 char setup_frame[SETUP_FRAME_LEN];
493 char *pa = &setup_frame[0];
494
495 memset(pa, 0xff, SETUP_FRAME_LEN);
496
497 for (i = 0; i < ETH_ALEN; i++) {
498 *(pa + (i & 1)) = dev->enetaddr[i];
499 if (i & 0x01) {
500 pa += 4;
501 }
502 }
503
504 for(i = 0; tx_ring[tx_new].status & cpu_to_le32(T_OWN); i++) {
505 if (i >= TOUT_LOOP) {
506 printf("%s: tx error buffer not ready\n", dev->name);
507 goto Done;
508 }
509 }
510
511 tx_ring[tx_new].buf = cpu_to_le32(phys_to_bus((u32) &setup_frame[0]));
512 tx_ring[tx_new].des1 = cpu_to_le32(TD_TER | TD_SET| SETUP_FRAME_LEN);
513 tx_ring[tx_new].status = cpu_to_le32(T_OWN);
514
515 OUTL(dev, POLL_DEMAND, DE4X5_TPD);
516
517 for(i = 0; tx_ring[tx_new].status & cpu_to_le32(T_OWN); i++) {
518 if (i >= TOUT_LOOP) {
519 printf("%s: tx buffer not ready\n", dev->name);
520 goto Done;
521 }
522 }
523
524 if (le32_to_cpu(tx_ring[tx_new].status) != 0x7FFFFFFF) {
525 printf("TX error status2 = 0x%08X\n", le32_to_cpu(tx_ring[tx_new].status));
526 }
wdenk63f34912004-01-02 15:01:32 +0000527 tx_new = (tx_new+1) % NUM_TX_DESC;
528
wdenkc6097192002-11-03 00:24:07 +0000529Done:
530 return;
531}
532
wdenkc935d3b2004-01-03 19:43:48 +0000533#if defined(UPDATE_SROM) || !defined(CONFIG_TULIP_FIX_DAVICOM)
wdenkc6097192002-11-03 00:24:07 +0000534/* SROM Read and write routines.
535 */
wdenkc6097192002-11-03 00:24:07 +0000536static void
537sendto_srom(struct eth_device* dev, u_int command, u_long addr)
538{
539 OUTL(dev, command, addr);
540 udelay(1);
541}
542
543static int
544getfrom_srom(struct eth_device* dev, u_long addr)
545{
546 s32 tmp;
547
548 tmp = INL(dev, addr);
549 udelay(1);
550
551 return tmp;
552}
553
554/* Note: this routine returns extra data bits for size detection. */
555static int do_read_eeprom(struct eth_device *dev, u_long ioaddr, int location, int addr_len)
556{
557 int i;
558 unsigned retval = 0;
559 int read_cmd = location | (SROM_READ_CMD << addr_len);
560
561 sendto_srom(dev, SROM_RD | SROM_SR, ioaddr);
562 sendto_srom(dev, SROM_RD | SROM_SR | DT_CS, ioaddr);
563
564#ifdef DEBUG_SROM
565 printf(" EEPROM read at %d ", location);
566#endif
567
568 /* Shift the read command bits out. */
569 for (i = 4 + addr_len; i >= 0; i--) {
570 short dataval = (read_cmd & (1 << i)) ? EE_DATA_WRITE : 0;
571 sendto_srom(dev, SROM_RD | SROM_SR | DT_CS | dataval, ioaddr);
572 udelay(10);
573 sendto_srom(dev, SROM_RD | SROM_SR | DT_CS | dataval | DT_CLK, ioaddr);
574 udelay(10);
575#ifdef DEBUG_SROM2
576 printf("%X", getfrom_srom(dev, ioaddr) & 15);
577#endif
578 retval = (retval << 1) | ((getfrom_srom(dev, ioaddr) & EE_DATA_READ) ? 1 : 0);
579 }
580
581 sendto_srom(dev, SROM_RD | SROM_SR | DT_CS, ioaddr);
582
583#ifdef DEBUG_SROM2
584 printf(" :%X:", getfrom_srom(dev, ioaddr) & 15);
585#endif
586
587 for (i = 16; i > 0; i--) {
588 sendto_srom(dev, SROM_RD | SROM_SR | DT_CS | DT_CLK, ioaddr);
589 udelay(10);
590#ifdef DEBUG_SROM2
591 printf("%X", getfrom_srom(dev, ioaddr) & 15);
592#endif
593 retval = (retval << 1) | ((getfrom_srom(dev, ioaddr) & EE_DATA_READ) ? 1 : 0);
594 sendto_srom(dev, SROM_RD | SROM_SR | DT_CS, ioaddr);
595 udelay(10);
596 }
597
598 /* Terminate the EEPROM access. */
599 sendto_srom(dev, SROM_RD | SROM_SR, ioaddr);
600
601#ifdef DEBUG_SROM2
602 printf(" EEPROM value at %d is %5.5x.\n", location, retval);
603#endif
604
605 return retval;
606}
wdenkc935d3b2004-01-03 19:43:48 +0000607#endif /* UPDATE_SROM || !CONFIG_TULIP_FIX_DAVICOM */
wdenkc6097192002-11-03 00:24:07 +0000608
wdenkc935d3b2004-01-03 19:43:48 +0000609/* This executes a generic EEPROM command, typically a write or write
610 * enable. It returns the data output from the EEPROM, and thus may
611 * also be used for reads.
612 */
613#if defined(UPDATE_SROM) || !defined(CONFIG_TULIP_FIX_DAVICOM)
wdenkc6097192002-11-03 00:24:07 +0000614static int do_eeprom_cmd(struct eth_device *dev, u_long ioaddr, int cmd, int cmd_len)
615{
616 unsigned retval = 0;
617
618#ifdef DEBUG_SROM
619 printf(" EEPROM op 0x%x: ", cmd);
620#endif
621
622 sendto_srom(dev,SROM_RD | SROM_SR | DT_CS | DT_CLK, ioaddr);
623
624 /* Shift the command bits out. */
625 do {
626 short dataval = (cmd & (1 << cmd_len)) ? EE_WRITE_1 : EE_WRITE_0;
627 sendto_srom(dev,dataval, ioaddr);
628 udelay(10);
629
630#ifdef DEBUG_SROM2
631 printf("%X", getfrom_srom(dev,ioaddr) & 15);
632#endif
633
634 sendto_srom(dev,dataval | DT_CLK, ioaddr);
635 udelay(10);
636 retval = (retval << 1) | ((getfrom_srom(dev,ioaddr) & EE_DATA_READ) ? 1 : 0);
637 } while (--cmd_len >= 0);
638 sendto_srom(dev,SROM_RD | SROM_SR | DT_CS, ioaddr);
639
640 /* Terminate the EEPROM access. */
641 sendto_srom(dev,SROM_RD | SROM_SR, ioaddr);
642
643#ifdef DEBUG_SROM
644 printf(" EEPROM result is 0x%5.5x.\n", retval);
645#endif
646
647 return retval;
648}
wdenkc935d3b2004-01-03 19:43:48 +0000649#endif /* UPDATE_SROM || !CONFIG_TULIP_FIX_DAVICOM */
wdenkc6097192002-11-03 00:24:07 +0000650
wdenkc935d3b2004-01-03 19:43:48 +0000651#ifndef CONFIG_TULIP_FIX_DAVICOM
wdenkc6097192002-11-03 00:24:07 +0000652static int read_srom(struct eth_device *dev, u_long ioaddr, int index)
653{
654 int ee_addr_size = do_read_eeprom(dev, ioaddr, 0xff, 8) & 0x40000 ? 8 : 6;
655
656 return do_eeprom_cmd(dev, ioaddr,
657 (((SROM_READ_CMD << ee_addr_size) | index) << 16)
658 | 0xffff, 3 + ee_addr_size + 16);
659}
wdenkc935d3b2004-01-03 19:43:48 +0000660#endif /* CONFIG_TULIP_FIX_DAVICOM */
wdenkc6097192002-11-03 00:24:07 +0000661
662#ifdef UPDATE_SROM
663static int write_srom(struct eth_device *dev, u_long ioaddr, int index, int new_value)
664{
665 int ee_addr_size = do_read_eeprom(dev, ioaddr, 0xff, 8) & 0x40000 ? 8 : 6;
666 int i;
667 unsigned short newval;
668
669 udelay(10*1000); /* test-only */
670
671#ifdef DEBUG_SROM
672 printf("ee_addr_size=%d.\n", ee_addr_size);
673 printf("Writing new entry 0x%4.4x to offset %d.\n", new_value, index);
674#endif
675
676 /* Enable programming modes. */
677 do_eeprom_cmd(dev, ioaddr, (0x4f << (ee_addr_size-4)), 3+ee_addr_size);
678
679 /* Do the actual write. */
680 do_eeprom_cmd(dev, ioaddr,
681 (((SROM_WRITE_CMD<<ee_addr_size)|index) << 16) | new_value,
682 3 + ee_addr_size + 16);
683
684 /* Poll for write finished. */
685 sendto_srom(dev, SROM_RD | SROM_SR | DT_CS, ioaddr);
686 for (i = 0; i < 10000; i++) /* Typical 2000 ticks */
687 if (getfrom_srom(dev, ioaddr) & EE_DATA_READ)
688 break;
689
690#ifdef DEBUG_SROM
691 printf(" Write finished after %d ticks.\n", i);
692#endif
693
694 /* Disable programming. */
695 do_eeprom_cmd(dev, ioaddr, (0x40 << (ee_addr_size-4)), 3 + ee_addr_size);
696
697 /* And read the result. */
698 newval = do_eeprom_cmd(dev, ioaddr,
699 (((SROM_READ_CMD<<ee_addr_size)|index) << 16)
700 | 0xffff, 3 + ee_addr_size + 16);
701#ifdef DEBUG_SROM
702 printf(" New value at offset %d is %4.4x.\n", index, newval);
703#endif
704 return 1;
705}
706#endif
707
wdenkc935d3b2004-01-03 19:43:48 +0000708#ifndef CONFIG_TULIP_FIX_DAVICOM
wdenkc6097192002-11-03 00:24:07 +0000709static void read_hw_addr(struct eth_device *dev, bd_t *bis)
710{
Wolfgang Denk77ddac92005-10-13 16:45:02 +0200711 u_short tmp, *p = (u_short *)(&dev->enetaddr[0]);
wdenkc6097192002-11-03 00:24:07 +0000712 int i, j = 0;
713
714 for (i = 0; i < (ETH_ALEN >> 1); i++) {
715 tmp = read_srom(dev, DE4X5_APROM, ((SROM_HWADD >> 1) + i));
716 *p = le16_to_cpu(tmp);
717 j += *p++;
718 }
719
720 if ((j == 0) || (j == 0x2fffd)) {
721 memset (dev->enetaddr, 0, ETH_ALEN);
wdenkc935d3b2004-01-03 19:43:48 +0000722 debug ("Warning: can't read HW address from SROM.\n");
wdenkc6097192002-11-03 00:24:07 +0000723 goto Done;
724 }
725
726 return;
727
728Done:
729#ifdef UPDATE_SROM
730 update_srom(dev, bis);
731#endif
732 return;
733}
wdenkc935d3b2004-01-03 19:43:48 +0000734#endif /* CONFIG_TULIP_FIX_DAVICOM */
wdenkc6097192002-11-03 00:24:07 +0000735
736#ifdef UPDATE_SROM
737static void update_srom(struct eth_device *dev, bd_t *bis)
738{
739 int i;
740 static unsigned short eeprom[0x40] = {
741 0x140b, 0x6610, 0x0000, 0x0000, /* 00 */
742 0x0000, 0x0000, 0x0000, 0x0000, /* 04 */
743 0x00a3, 0x0103, 0x0000, 0x0000, /* 08 */
744 0x0000, 0x1f00, 0x0000, 0x0000, /* 0c */
745 0x0108, 0x038d, 0x0000, 0x0000, /* 10 */
746 0xe078, 0x0001, 0x0040, 0x0018, /* 14 */
747 0x0000, 0x0000, 0x0000, 0x0000, /* 18 */
748 0x0000, 0x0000, 0x0000, 0x0000, /* 1c */
749 0x0000, 0x0000, 0x0000, 0x0000, /* 20 */
750 0x0000, 0x0000, 0x0000, 0x0000, /* 24 */
751 0x0000, 0x0000, 0x0000, 0x0000, /* 28 */
752 0x0000, 0x0000, 0x0000, 0x0000, /* 2c */
753 0x0000, 0x0000, 0x0000, 0x0000, /* 30 */
754 0x0000, 0x0000, 0x0000, 0x0000, /* 34 */
755 0x0000, 0x0000, 0x0000, 0x0000, /* 38 */
756 0x0000, 0x0000, 0x0000, 0x4e07, /* 3c */
757 };
758
759 /* Ethernet Addr... */
760 eeprom[0x0a] = ((bis->bi_enetaddr[1] & 0xff) << 8) | (bis->bi_enetaddr[0] & 0xff);
761 eeprom[0x0b] = ((bis->bi_enetaddr[3] & 0xff) << 8) | (bis->bi_enetaddr[2] & 0xff);
762 eeprom[0x0c] = ((bis->bi_enetaddr[5] & 0xff) << 8) | (bis->bi_enetaddr[4] & 0xff);
763
764 for (i=0; i<0x40; i++)
765 {
766 write_srom(dev, DE4X5_APROM, i, eeprom[i]);
767 }
768}
wdenkc935d3b2004-01-03 19:43:48 +0000769#endif /* UPDATE_SROM */
wdenkc6097192002-11-03 00:24:07 +0000770
Jon Loeligerddb5d86f2007-07-10 11:13:21 -0500771#endif