blob: 1b5b70512d1446b2c6af340de5655eb5492d685d [file] [log] [blame]
Marek Vasutdae0f5c2014-07-22 02:34:52 +02001/*
2 * S3C24xx SD/MMC driver
3 *
4 * Based on OpenMoko S3C24xx driver by Harald Welte <laforge@openmoko.org>
5 *
6 * Copyright (C) 2014 Marek Vasut <marex@denx.de>
7 *
8 * SPDX-License-Identifier: GPL-2.0+
9 */
10
11#include <common.h>
12#include <malloc.h>
13#include <mmc.h>
14#include <errno.h>
15#include <asm/arch/s3c24x0_cpu.h>
16#include <asm/io.h>
17#include <asm/unaligned.h>
18
19#define S3C2440_SDICON_SDRESET (1 << 8)
20#define S3C2410_SDICON_FIFORESET (1 << 1)
21#define S3C2410_SDICON_CLOCKTYPE (1 << 0)
22
23#define S3C2410_SDICMDCON_LONGRSP (1 << 10)
24#define S3C2410_SDICMDCON_WAITRSP (1 << 9)
25#define S3C2410_SDICMDCON_CMDSTART (1 << 8)
26#define S3C2410_SDICMDCON_SENDERHOST (1 << 6)
27#define S3C2410_SDICMDCON_INDEX 0x3f
28
29#define S3C2410_SDICMDSTAT_CRCFAIL (1 << 12)
30#define S3C2410_SDICMDSTAT_CMDSENT (1 << 11)
31#define S3C2410_SDICMDSTAT_CMDTIMEOUT (1 << 10)
32#define S3C2410_SDICMDSTAT_RSPFIN (1 << 9)
33
34#define S3C2440_SDIDCON_DS_WORD (2 << 22)
35#define S3C2410_SDIDCON_TXAFTERRESP (1 << 20)
36#define S3C2410_SDIDCON_RXAFTERCMD (1 << 19)
37#define S3C2410_SDIDCON_BLOCKMODE (1 << 17)
38#define S3C2410_SDIDCON_WIDEBUS (1 << 16)
39#define S3C2440_SDIDCON_DATSTART (1 << 14)
40#define S3C2410_SDIDCON_XFER_RXSTART (2 << 12)
41#define S3C2410_SDIDCON_XFER_TXSTART (3 << 12)
42#define S3C2410_SDIDCON_BLKNUM 0x7ff
43
44#define S3C2410_SDIDSTA_FIFOFAIL (1 << 8)
45#define S3C2410_SDIDSTA_CRCFAIL (1 << 7)
46#define S3C2410_SDIDSTA_RXCRCFAIL (1 << 6)
47#define S3C2410_SDIDSTA_DATATIMEOUT (1 << 5)
48#define S3C2410_SDIDSTA_XFERFINISH (1 << 4)
49
50#define S3C2410_SDIFSTA_TFHALF (1 << 11)
51#define S3C2410_SDIFSTA_COUNTMASK 0x7f
52
53/*
54 * WARNING: We only support one SD IP block.
55 * NOTE: It's not likely there will ever exist an S3C24xx with two,
56 * at least not in this universe all right.
57 */
58static int wide_bus;
59
60static int
61s3cmmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
62{
63 struct s3c24x0_sdi *sdi_regs = s3c24x0_get_base_sdi();
64 uint32_t sdiccon, sdicsta, sdidcon, sdidsta, sdidat, sdifsta;
65 uint32_t sdicsta_wait_bit = S3C2410_SDICMDSTAT_CMDSENT;
66 unsigned int timeout = 100000;
67 int ret = 0, xfer_len, data_offset = 0;
68 const uint32_t sdidsta_err_mask = S3C2410_SDIDSTA_FIFOFAIL |
69 S3C2410_SDIDSTA_CRCFAIL | S3C2410_SDIDSTA_RXCRCFAIL |
70 S3C2410_SDIDSTA_DATATIMEOUT;
71
72
73 writel(0xffffffff, &sdi_regs->sdicsta);
74 writel(0xffffffff, &sdi_regs->sdidsta);
75 writel(0xffffffff, &sdi_regs->sdifsta);
76
77 /* Set up data transfer (if applicable). */
78 if (data) {
79 writel(data->blocksize, &sdi_regs->sdibsize);
80
81 sdidcon = data->blocks & S3C2410_SDIDCON_BLKNUM;
82 sdidcon |= S3C2410_SDIDCON_BLOCKMODE;
83#if defined(CONFIG_S3C2440)
84 sdidcon |= S3C2440_SDIDCON_DS_WORD | S3C2440_SDIDCON_DATSTART;
85#endif
86 if (wide_bus)
87 sdidcon |= S3C2410_SDIDCON_WIDEBUS;
88
89 if (data->flags & MMC_DATA_READ) {
90 sdidcon |= S3C2410_SDIDCON_RXAFTERCMD;
91 sdidcon |= S3C2410_SDIDCON_XFER_RXSTART;
92 } else {
93 sdidcon |= S3C2410_SDIDCON_TXAFTERRESP;
94 sdidcon |= S3C2410_SDIDCON_XFER_TXSTART;
95 }
96
97 writel(sdidcon, &sdi_regs->sdidcon);
98 }
99
100 /* Write CMD arg. */
101 writel(cmd->cmdarg, &sdi_regs->sdicarg);
102
103 /* Write CMD index. */
104 sdiccon = cmd->cmdidx & S3C2410_SDICMDCON_INDEX;
105 sdiccon |= S3C2410_SDICMDCON_SENDERHOST;
106 sdiccon |= S3C2410_SDICMDCON_CMDSTART;
107
108 /* Command with short response. */
109 if (cmd->resp_type & MMC_RSP_PRESENT) {
110 sdiccon |= S3C2410_SDICMDCON_WAITRSP;
111 sdicsta_wait_bit = S3C2410_SDICMDSTAT_RSPFIN;
112 }
113
114 /* Command with long response. */
115 if (cmd->resp_type & MMC_RSP_136)
116 sdiccon |= S3C2410_SDICMDCON_LONGRSP;
117
118 /* Start the command. */
119 writel(sdiccon, &sdi_regs->sdiccon);
120
121 /* Wait for the command to complete or for response. */
122 for (timeout = 100000; timeout; timeout--) {
123 sdicsta = readl(&sdi_regs->sdicsta);
124 if (sdicsta & sdicsta_wait_bit)
125 break;
126
127 if (sdicsta & S3C2410_SDICMDSTAT_CMDTIMEOUT)
128 timeout = 1;
129 }
130
131 /* Clean the status bits. */
132 setbits_le32(&sdi_regs->sdicsta, 0xf << 9);
133
134 if (!timeout) {
135 puts("S3C SDI: Command timed out!\n");
136 ret = TIMEOUT;
137 goto error;
138 }
139
140 /* Read out the response. */
141 if (cmd->resp_type & MMC_RSP_136) {
142 cmd->response[0] = readl(&sdi_regs->sdirsp0);
143 cmd->response[1] = readl(&sdi_regs->sdirsp1);
144 cmd->response[2] = readl(&sdi_regs->sdirsp2);
145 cmd->response[3] = readl(&sdi_regs->sdirsp3);
146 } else {
147 cmd->response[0] = readl(&sdi_regs->sdirsp0);
148 }
149
150 /* If there are no data, we're done. */
151 if (!data)
152 return 0;
153
154 xfer_len = data->blocksize * data->blocks;
155
156 while (xfer_len > 0) {
157 sdidsta = readl(&sdi_regs->sdidsta);
158 sdifsta = readl(&sdi_regs->sdifsta);
159
160 if (sdidsta & sdidsta_err_mask) {
161 printf("S3C SDI: Data error (sdta=0x%08x)\n", sdidsta);
162 ret = -EIO;
163 goto error;
164 }
165
166 if (data->flags & MMC_DATA_READ) {
167 if ((sdifsta & S3C2410_SDIFSTA_COUNTMASK) < 4)
168 continue;
169 sdidat = readl(&sdi_regs->sdidat);
170 put_unaligned_le32(sdidat, data->dest + data_offset);
171 } else { /* Write */
172 /* TX FIFO half full. */
173 if (!(sdifsta & S3C2410_SDIFSTA_TFHALF))
174 continue;
175
176 /* TX FIFO is below 32b full, write. */
177 sdidat = get_unaligned_le32(data->src + data_offset);
178 writel(sdidat, &sdi_regs->sdidat);
179 }
180 data_offset += 4;
181 xfer_len -= 4;
182 }
183
184 /* Wait for the command to complete or for response. */
185 for (timeout = 100000; timeout; timeout--) {
186 sdidsta = readl(&sdi_regs->sdidsta);
187 if (sdidsta & S3C2410_SDIDSTA_XFERFINISH)
188 break;
189
190 if (sdidsta & S3C2410_SDIDSTA_DATATIMEOUT)
191 timeout = 1;
192 }
193
194 /* Clear status bits. */
195 writel(0x6f8, &sdi_regs->sdidsta);
196
197 if (!timeout) {
198 puts("S3C SDI: Command timed out!\n");
199 ret = TIMEOUT;
200 goto error;
201 }
202
203 writel(0, &sdi_regs->sdidcon);
204
205 return 0;
206error:
207 return ret;
208}
209
210static void s3cmmc_set_ios(struct mmc *mmc)
211{
212 struct s3c24x0_sdi *sdi_regs = s3c24x0_get_base_sdi();
213 uint32_t divider = 0;
214
215 wide_bus = (mmc->bus_width == 4);
216
217 if (!mmc->clock)
218 return;
219
220 divider = DIV_ROUND_UP(get_PCLK(), mmc->clock);
221 if (divider)
222 divider--;
223
224 writel(divider, &sdi_regs->sdipre);
225 mdelay(125);
226}
227
228static int s3cmmc_init(struct mmc *mmc)
229{
230 struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power();
231 struct s3c24x0_sdi *sdi_regs = s3c24x0_get_base_sdi();
232
233 /* Start the clock. */
234 setbits_le32(&clk_power->clkcon, 1 << 9);
235
236#if defined(CONFIG_S3C2440)
237 writel(S3C2440_SDICON_SDRESET, &sdi_regs->sdicon);
238 mdelay(10);
239 writel(0x7fffff, &sdi_regs->sdidtimer);
240#else
241 writel(0xffff, &sdi_regs->sdidtimer);
242#endif
243 writel(MMC_MAX_BLOCK_LEN, &sdi_regs->sdibsize);
244 writel(0x0, &sdi_regs->sdiimsk);
245
246 writel(S3C2410_SDICON_FIFORESET | S3C2410_SDICON_CLOCKTYPE,
247 &sdi_regs->sdicon);
248
249 mdelay(125);
250
251 return 0;
252}
253
254struct s3cmmc_priv {
255 struct mmc_config cfg;
256 int (*getcd)(struct mmc *);
257 int (*getwp)(struct mmc *);
258};
259
260static int s3cmmc_getcd(struct mmc *mmc)
261{
262 struct s3cmmc_priv *priv = mmc->priv;
263 if (priv->getcd)
264 return priv->getcd(mmc);
265 else
266 return 0;
267}
268
269static int s3cmmc_getwp(struct mmc *mmc)
270{
271 struct s3cmmc_priv *priv = mmc->priv;
272 if (priv->getwp)
273 return priv->getwp(mmc);
274 else
275 return 0;
276}
277
278static const struct mmc_ops s3cmmc_ops = {
279 .send_cmd = s3cmmc_send_cmd,
280 .set_ios = s3cmmc_set_ios,
281 .init = s3cmmc_init,
282 .getcd = s3cmmc_getcd,
283 .getwp = s3cmmc_getwp,
284};
285
286int s3cmmc_initialize(bd_t *bis, int (*getcd)(struct mmc *),
287 int (*getwp)(struct mmc *))
288{
289 struct s3cmmc_priv *priv;
290 struct mmc *mmc;
291 struct mmc_config *cfg;
292
293 priv = calloc(1, sizeof(*priv));
294 if (!priv)
295 return -ENOMEM;
296 cfg = &priv->cfg;
297
298 cfg->name = "S3C MMC";
299 cfg->ops = &s3cmmc_ops;
300 cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34;
301 cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_HC | MMC_MODE_HS;
302 cfg->f_min = 400000;
303 cfg->f_max = get_PCLK() / 2;
304 cfg->b_max = 0x80;
305
306#if defined(CONFIG_S3C2410)
307 /*
308 * S3C2410 has some bug that prevents reliable
309 * operation at higher speed
310 */
311 cfg->f_max /= 2;
312#endif
313
314 mmc = mmc_create(cfg, priv);
315 if (!mmc) {
316 free(priv);
317 return -ENOMEM;
318 }
319
320 return 0;
321}