blob: e978cf8c824ff3b7b012a3dca011835bcb62451a [file] [log] [blame]
Matthias Kaehlcke403ce1f2009-07-16 21:19:29 +02001/*
2 * (C) Copyright 2006
3 * KwikByte <kb9200_dev@kwikbyte.com>
4 *
5 * (C) Copyright 2009
6 * Matthias Kaehlcke <matthias@kaehlcke.net>
7 *
Wolfgang Denk1a459662013-07-08 09:37:19 +02008 * SPDX-License-Identifier: GPL-2.0+
Matthias Kaehlcke403ce1f2009-07-16 21:19:29 +02009 */
10
11#include <common.h>
12#include <asm/io.h>
13#include <asm/arch/AT91RM9200.h>
14#include <asm/arch/hardware.h>
15
16#include <nand.h>
17
18/*
19 * hardware specific access to control-lines
20 */
21
22#define MASK_ALE (1 << 22) /* our ALE is A22 */
23#define MASK_CLE (1 << 21) /* our CLE is A21 */
24
25#define KB9202_NAND_NCE (1 << 28) /* EN* on D28 */
26#define KB9202_NAND_BUSY (1 << 29) /* RB* on D29 */
27
28#define KB9202_SMC2_NWS (1 << 2)
29#define KB9202_SMC2_TDF (1 << 8)
30#define KB9202_SMC2_RWSETUP (1 << 24)
31#define KB9202_SMC2_RWHOLD (1 << 29)
32
33/*
34 * Board-specific function to access device control signals
35 */
36static void kb9202_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
37{
Scott Wood17cb4b82016-05-30 13:57:56 -050038 struct nand_chip *this = mtd_to_nand(mtd);
Matthias Kaehlcke403ce1f2009-07-16 21:19:29 +020039
40 if (ctrl & NAND_CTRL_CHANGE) {
41 ulong IO_ADDR_W = (ulong) this->IO_ADDR_W;
42
43 /* clear ALE and CLE bits */
44 IO_ADDR_W &= ~(MASK_ALE | MASK_CLE);
45
46 if (ctrl & NAND_CLE)
47 IO_ADDR_W |= MASK_CLE;
48
49 if (ctrl & NAND_ALE)
50 IO_ADDR_W |= MASK_ALE;
51
52 this->IO_ADDR_W = (void *) IO_ADDR_W;
53
54 if (ctrl & NAND_NCE)
55 writel(KB9202_NAND_NCE, AT91C_PIOC_CODR);
56 else
57 writel(KB9202_NAND_NCE, AT91C_PIOC_SODR);
58 }
59
60 if (cmd != NAND_CMD_NONE)
61 writeb(cmd, this->IO_ADDR_W);
62}
63
64
65/*
66 * Board-specific function to access the device ready signal.
67 */
68static int kb9202_nand_ready(struct mtd_info *mtd)
69{
70 return readl(AT91C_PIOC_PDSR) & KB9202_NAND_BUSY;
71}
72
73
74/*
75 * Board-specific NAND init. Copied from include/linux/mtd/nand.h for reference.
76 *
77 * struct nand_chip - NAND Private Flash Chip Data
78 * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the flash device
79 * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the flash device
80 * @hwcontrol: [BOARDSPECIFIC] hardwarespecific function for accesing control-lines
81 * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing device ready/busy line
82 * If set to NULL no access to ready/busy is available and the ready/busy information
83 * is read from the chip status register
84 * @enable_hwecc: [BOARDSPECIFIC] function to enable (reset) hardware ecc generator. Must only
85 * be provided if a hardware ECC is available
86 * @eccmode: [BOARDSPECIFIC] mode of ecc, see defines
87 * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transfering data from array to read regs (tR)
88 * @options: [BOARDSPECIFIC] various chip options. They can partly be set to inform nand_scan about
89 * special functionality. See the defines for further explanation
90*/
91/*
92 * This routine initializes controller and GPIOs.
93 */
94int board_nand_init(struct nand_chip *nand)
95{
96 unsigned int value;
97
98 nand->ecc.mode = NAND_ECC_SOFT;
99 nand->cmd_ctrl = kb9202_nand_hwcontrol;
100 nand->dev_ready = kb9202_nand_ready;
101
102 /* in case running outside of bootloader */
103 writel(1 << AT91C_ID_PIOC, AT91C_PMC_PCER);
104
105 /* setup nand flash access (allow ample margin) */
106 /* 4 wait states, 1 setup, 1 hold, 1 float for 8-bit device */
107 writel(AT91C_SMC2_WSEN | KB9202_SMC2_NWS | KB9202_SMC2_TDF |
108 AT91C_SMC2_DBW_8 | KB9202_SMC2_RWSETUP | KB9202_SMC2_RWHOLD,
109 AT91C_SMC_CSR3);
110
111 /* enable internal NAND controller */
112 value = readl(AT91C_EBI_CSA);
113 value |= AT91C_EBI_CS3A_SMC_SmartMedia;
114 writel(value, AT91C_EBI_CSA);
115
116 /* enable SMOE/SMWE */
117 writel(AT91C_PC1_BFRDY_SMOE | AT91C_PC3_BFBAA_SMWE, AT91C_PIOC_ASR);
118 writel(AT91C_PC1_BFRDY_SMOE | AT91C_PC3_BFBAA_SMWE, AT91C_PIOC_PDR);
119 writel(AT91C_PC1_BFRDY_SMOE | AT91C_PC3_BFBAA_SMWE, AT91C_PIOC_OER);
120
121 /* set NCE to high */
122 writel(KB9202_NAND_NCE, AT91C_PIOC_SODR);
123
124 /* disable output on pin connected to the busy line of the NAND */
125 writel(KB9202_NAND_BUSY, AT91C_PIOC_ODR);
126
127 /* enable the PIO to control NCE and BUSY */
128 writel(KB9202_NAND_NCE | KB9202_NAND_BUSY, AT91C_PIOC_PER);
129
130 /* enable output for NCE */
131 writel(KB9202_NAND_NCE, AT91C_PIOC_OER);
132
133 return (0);
134}