blob: ca3f3f7a7110f7adc0768762b74b90f714957e15 [file] [log] [blame]
Tom Rini83d290c2018-05-06 17:58:06 -04001/* SPDX-License-Identifier: GPL-2.0+ */
Bin Meng98af34f2016-02-17 00:16:22 -08002/*
3 * Copyright (C) 2016, Bin Meng <bmeng.cn@gmail.com>
Bin Meng98af34f2016-02-17 00:16:22 -08004 */
5
6#ifndef _SMSC_SIO1007_H_
7#define _SMSC_SIO1007_H_
8
9/*
10 * The I/O base address of SIO1007 at power-up is determined by the SYSOPT0
11 * and SYSOPT1 pins at the deasserting edge of PCIRST#. The combination of
12 * SYSOPT0 and SYSOPT1 determines one of the following addresses.
13 */
14#define SIO1007_IOPORT0 0x002e
15#define SIO1007_IOPORT1 0x004e
16#define SIO1007_IOPORT2 0x162e
17#define SIO1007_IOPORT3 0x164e
18
19/* SIO1007 registers */
20
21#define DEV_POWER_CTRL 0x02
22#define UART1_POWER_ON (1 << 3)
23#define UART2_POWER_ON (1 << 7)
24
25#define UART1_IOBASE 0x24
26#define UART2_IOBASE 0x25
27#define UART_IRQ 0x28
28
29#define RTR_IOBASE_HIGH 0x21
30#define RTR_IOBASE_LOW 0x30
31
32#define GPIO0_DIR 0x31
33#define GPIO1_DIR 0x35
34#define GPIO_DIR_INPUT 0
35#define GPIO_DIR_OUTPUT 1
36
37#define GPIO0_POL 0x32
38#define GPIO1_POL 0x36
39#define GPIO_POL_NO_INVERT 0
40#define GPIO_POL_INVERT 1
41
42#define GPIO0_TYPE 0x33
43#define GPIO1_TYPE 0x37
44#define GPIO_TYPE_PUSH_PULL 0
45#define GPIO_TYPE_OPEN_DRAIN 1
46
47#define DEV_ACTIVATE 0x3a
48#define RTR_EN (1 << 1)
49
50/* Runtime register offset */
51
52#define GPIO0_DATA 0xc
53#define GPIO1_DATA 0xe
54
55/* Number of serial ports supported */
56#define SIO1007_UART_NUM 2
57
58/* Number of gpio pins supported */
59#define GPIO_NUM_PER_GROUP 8
60#define GPIO_GROUP_NUM 2
61#define SIO1007_GPIO_NUM (GPIO_NUM_PER_GROUP * GPIO_GROUP_NUM)
62
63/**
64 * Configure the I/O port address of the specified serial device and
65 * enable the serial device.
66 *
67 * @port: SIO1007 I/O port address
68 * @num: serial device number (0 or 1)
69 * @iobase: processor I/O port address to assign to this serial device
70 * @irq: processor IRQ number to assign to this serial device
71 */
72void sio1007_enable_serial(int port, int num, int iobase, int irq);
73
74/**
75 * Configure the I/O port address of the runtime register block and
76 * enable the address decoding.
77 *
78 * @port: SIO1007 I/O port address
79 * @iobase: processor I/O port address to assign to the runtime registers
80 */
81void sio1007_enable_runtime(int port, int iobase);
82
83/**
84 * Configure the direction/polority/type of a specified GPIO pin
85 *
86 * @port: SIO1007 I/O port address
87 * @gpio: GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
88 * @dir: GPIO_DIR_INPUT or GPIO_DIR_OUTPUT
89 * @pol: GPIO_POL_NO_INVERT or GPIO_POL_INVERT
90 * @type: GPIO_TYPE_PUSH_PULL or GPIO_TYPE_OPEN_DRAIN
91 */
92void sio1007_gpio_config(int port, int gpio, int dir, int pol, int type);
93
94/**
95 * Get a GPIO pin value.
96 * This will work whether the GPIO is an input or an output.
97 *
98 * @port: runtime register block I/O port address
99 * @gpio: GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
100 * @return: 0 if low, 1 if high, -EINVAL if gpio number is invalid
101 */
102int sio1007_gpio_get_value(int port, int gpio);
103
104/**
105 * Set a GPIO pin value.
106 * This will only work when the GPIO is configured as an output.
107 *
108 * @port: runtime register block I/O port address
109 * @gpio: GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
110 * @val: 0 if low, 1 if high
111 */
112void sio1007_gpio_set_value(int port, int gpio, int val);
113
114#endif /* _SMSC_SIO1007_H_ */