blob: d007f58764d4facbb7b1c8cba0882a2c41e8c4ac [file] [log] [blame]
Neil Armstrong96e7b5a2017-11-27 10:16:19 +01001U-Boot for LibreTech CC
2=======================
3
4LibreTech CC is a single board computer manufactured by Libre Technology
5with the following specifications:
6
Neil Armstrongc95848c2018-06-27 17:19:02 +02007 - Amlogic S905X ARM Cortex-A53 quad-core SoC @ 1.5GHz
Neil Armstrong96e7b5a2017-11-27 10:16:19 +01008 - ARM Mali 450 GPU
9 - 2GB DDR3 SDRAM
Neil Armstrongc95848c2018-06-27 17:19:02 +020010 - 10/100 Ethernet
Neil Armstrong96e7b5a2017-11-27 10:16:19 +010011 - HDMI 2.0 4K/60Hz display
12 - 40-pin GPIO header
Neil Armstrongc95848c2018-06-27 17:19:02 +020013 - 4 x USB 2.0 Host
Neil Armstrong96e7b5a2017-11-27 10:16:19 +010014 - eMMC, microSD
15 - Infrared receiver
16
17Schematics are available on the manufacturer website.
18
19Currently the U-Boot port supports the following devices:
20 - serial
21 - eMMC, microSD
22 - Ethernet
Neil Armstrongc95848c2018-06-27 17:19:02 +020023 - I2C
24 - Regulators
25 - Reset controller
26 - Clock controller
27 - USB Host
28 - ADC
Neil Armstrong96e7b5a2017-11-27 10:16:19 +010029
30U-Boot compilation
31==================
32
33 > export ARCH=arm
34 > export CROSS_COMPILE=aarch64-none-elf-
35 > make libretech-cc_defconfig
36 > make
37
38Image creation
39==============
40
41Amlogic doesn't provide sources for the firmware and for tools needed
42to create the bootloader image, so it is necessary to obtain them from
43the git tree published by the board vendor:
44
45 > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
46 > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
47 > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
48 > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
49 > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
50 > git clone https://github.com/BayLibre/u-boot.git -b libretech-cc amlogic-u-boot
51 > cd amlogic-u-boot
52 > make libretech_cc_defconfig
53 > make
54 > export FIPDIR=$PWD/fip
55
56Go back to mainline U-Boot source tree then :
57 > mkdir fip
58
59 > cp $FIPDIR/gxl/bl2.bin fip/
60 > cp $FIPDIR/gxl/acs.bin fip/
61 > cp $FIPDIR/gxl/bl21.bin fip/
62 > cp $FIPDIR/gxl/bl30.bin fip/
63 > cp $FIPDIR/gxl/bl301.bin fip/
64 > cp $FIPDIR/gxl/bl31.img fip/
65 > cp u-boot.bin fip/bl33.bin
66
67 > $FIPDIR/blx_fix.sh \
68 fip/bl30.bin \
69 fip/zero_tmp \
70 fip/bl30_zero.bin \
71 fip/bl301.bin \
72 fip/bl301_zero.bin \
73 fip/bl30_new.bin \
74 bl30
75
76 > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
77
78 > $FIPDIR/blx_fix.sh \
79 fip/bl2_acs.bin \
80 fip/zero_tmp \
81 fip/bl2_zero.bin \
82 fip/bl21.bin \
83 fip/bl21_zero.bin \
84 fip/bl2_new.bin \
85 bl2
86
87 > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin
88 > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img
89 > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin
90 > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig
91 > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \
92 --output fip/u-boot.bin \
93 --bl2 fip/bl2.n.bin.sig \
94 --bl30 fip/bl30_new.bin.enc \
95 --bl31 fip/bl31.img.enc \
96 --bl33 fip/bl33.bin.enc
97
98and then write the image to SD with:
99
100 > DEV=/dev/your_sd_device
101 > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
102 > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444