blob: 9cc219e5a80a3922e12af79047fd1dcc83523d03 [file] [log] [blame]
Ira W. Snyder98397092011-11-23 08:25:58 -08001/*
ramneek mehresh3d7506f2012-04-18 19:39:53 +00002 * Copyright 2009-2010,2012 Freescale Semiconductor, Inc.
Ira W. Snyder98397092011-11-23 08:25:58 -08003 *
Wolfgang Denk1a459662013-07-08 09:37:19 +02004 * SPDX-License-Identifier: GPL-2.0+
Ira W. Snyder98397092011-11-23 08:25:58 -08005 */
6
7#ifndef __CONFIG_H
8#define __CONFIG_H
9
10/* The P2020COME board is only booted via the Freescale On-Chip ROM */
11#define CONFIG_SYS_RAMBOOT
12#define CONFIG_SYS_EXTRA_ENV_RELOC
13
14#define CONFIG_SYS_TEXT_BASE 0xf8f80000
15#define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc
16
17#ifdef CONFIG_SDCARD
18#define CONFIG_RAMBOOT_SDCARD 1
19#endif
20
21#ifdef CONFIG_SPIFLASH
22#define CONFIG_RAMBOOT_SPIFLASH 1
23#endif
24
25#ifndef CONFIG_SYS_MONITOR_BASE
26#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
27#endif
28
29/* High Level Configuration Options */
30#define CONFIG_BOOKE 1 /* BOOKE */
31#define CONFIG_E500 1 /* BOOKE e500 family */
32#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/P1020/P2020,etc*/
33#define CONFIG_P2020 1
34#define CONFIG_P2020COME 1
35#define CONFIG_FSL_ELBC 1 /* Enable eLBC Support */
36#define CONFIG_MP
37
38#define CONFIG_PCI 1 /* Enable PCI/PCIE */
39#if defined(CONFIG_PCI)
40#define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */
41#define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */
42#define CONFIG_PCIE3 1 /* PCIE controller 3 (slot 3) */
43
44#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
Gabor Juhos842033e2013-05-30 07:06:12 +000045#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
Ira W. Snyder98397092011-11-23 08:25:58 -080046#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
47#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
48#endif /* #if defined(CONFIG_PCI) */
49#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
50#define CONFIG_TSEC_ENET /* tsec ethernet support */
51#define CONFIG_ENV_OVERWRITE
52
53#if defined(CONFIG_PCI)
54#define CONFIG_E1000 1 /* E1000 pci Ethernet card */
55#endif
56
57#ifndef __ASSEMBLY__
58extern unsigned long get_board_ddr_clk(unsigned long dummy);
59extern unsigned long get_board_sys_clk(unsigned long dummy);
60#endif
61
62/*
63 * For P2020COME DDRCLK and SYSCLK are from the same oscillator
64 * For DA phase the SYSCLK is 66MHz
65 * For EA phase the SYSCLK is 100MHz
66 */
67#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0)
68#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
69
70#define CONFIG_HWCONFIG
71
72/*
73 * These can be toggled for performance analysis, otherwise use default.
74 */
75#define CONFIG_L2_CACHE /* toggle L2 cache */
76#define CONFIG_BTB /* toggle branch prediction */
77
78#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
79
80#define CONFIG_ENABLE_36BIT_PHYS 1
81
82#ifdef CONFIG_PHYS_64BIT
83#define CONFIG_ADDR_MAP 1
84#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
85#endif
86
87#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
88#define CONFIG_SYS_MEMTEST_END 0x1fffffff
89#define CONFIG_PANIC_HANG /* do not reset board on panic */
90
Ira W. Snyder98397092011-11-23 08:25:58 -080091 /*
92 * Config the L2 Cache as L2 SRAM
93 */
94#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
95#ifdef CONFIG_PHYS_64BIT
96#define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull
97#else
98#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
99#endif
100#define CONFIG_SYS_L2_SIZE (512 << 10)
101#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR \
102 + CONFIG_SYS_L2_SIZE)
103
104#define CONFIG_SYS_CCSRBAR 0xffe00000
105#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
106
107/* DDR Setup */
108#define CONFIG_FSL_DDR3
109#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
110#define CONFIG_DDR_SPD
111
112#define CONFIG_DDR_ECC
113#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
114#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
115
116#define CONFIG_SYS_SDRAM_SIZE 2048ULL /* DDR size on P2020COME */
117#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
118#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
119
120#define CONFIG_NUM_DDR_CONTROLLERS 1
121#define CONFIG_DIMM_SLOTS_PER_CTLR 1
122#define CONFIG_CHIP_SELECTS_PER_CTRL 2
123
124#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
125#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
126#define CONFIG_SYS_DDR_SBE 0x00ff0000
127
128#define CONFIG_SYS_SPD_BUS_NUM 1
129#define SPD_EEPROM_ADDRESS 0x53
130
131/*
132 * Memory map
133 *
134 * 0x0000_0000 0x7fff_ffff DDR3 2G Cacheable
135 * 0x8000_0000 0x9fff_ffff PCI Express 3 Mem 1G non-cacheable
136 * 0xa000_0000 0xbfff_ffff PCI Express 2 Mem 1G non-cacheable
137 * 0xc000_0000 0xdfff_ffff PCI Express 1 Mem 1G non-cacheable
138 * 0xffc1_0000 0xffc1_ffff PCI Express 3 IO 64K non-cacheable
139 * 0xffc2_0000 0xffc2_ffff PCI Express 2 IO 64K non-cacheable
140 * 0xffc3_0000 0xffc3_ffff PCI Express 1 IO 64K non-cacheable
141 *
142 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
143 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
144 */
145
146/*
147 * Local Bus Definitions
148 */
149
150/* There is no NOR Flash on P2020COME */
151#define CONFIG_SYS_NO_FLASH
152
153#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
154#define CONFIG_HWCONFIG
155
156#define CONFIG_SYS_INIT_RAM_LOCK 1
157#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
158#ifdef CONFIG_PHYS_64BIT
159#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
160#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
161/* the assembler doesn't like typecast */
162#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
163 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
164 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
165#else
166#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
167#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
168#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
169#endif
170#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
171
172#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
173 - GENERATED_GBL_DATA_SIZE)
174#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
175
176#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
177#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
178
179/* Serial Port - controlled on board with jumper J8
180 * open - index 2
181 * shorted - index 1
182 */
183#define CONFIG_CONS_INDEX 1
184#define CONFIG_SYS_NS16550
185#define CONFIG_SYS_NS16550_SERIAL
186#define CONFIG_SYS_NS16550_REG_SIZE 1
187#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
188
Ira W. Snyder98397092011-11-23 08:25:58 -0800189#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
190
191#define CONFIG_SYS_BAUDRATE_TABLE \
192 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
193
194#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
195#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
196
197/* Use the HUSH parser */
198#define CONFIG_SYS_HUSH_PARSER
Ira W. Snyder98397092011-11-23 08:25:58 -0800199
200/*
201 * Pass open firmware flat tree
202 */
203#define CONFIG_OF_LIBFDT 1
204#define CONFIG_OF_BOARD_SETUP 1
205#define CONFIG_OF_STDOUT_VIA_ALIAS 1
206
207/* new uImage format support */
208#define CONFIG_FIT 1
209#define CONFIG_FIT_VERBOSE 1
210
211/* I2C */
Heiko Schocher00f792e2012-10-24 13:48:22 +0200212#define CONFIG_SYS_I2C
213#define CONFIG_SYS_I2C_FSL
214#define CONFIG_SYS_FSL_I2C_SPEED 400000
215#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
216#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
217#define CONFIG_SYS_FSL_I2C2_SPEED 400000
218#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
219#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
Ira W. Snyder98397092011-11-23 08:25:58 -0800220#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
Ira W. Snyder98397092011-11-23 08:25:58 -0800221
222/*
223 * I2C2 EEPROM
224 */
225#define CONFIG_ID_EEPROM
226#ifdef CONFIG_ID_EEPROM
227#define CONFIG_SYS_I2C_EEPROM_NXID
228#endif
229#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
230#define CONFIG_SYS_I2C_EEPROM_ADDR2 0x18
231#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
232#define CONFIG_SYS_EEPROM_BUS_NUM 0
233#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
234
235/*
236 * eSPI - Enhanced SPI
237 */
238#define CONFIG_FSL_ESPI
239#define CONFIG_SPI_FLASH
240#define CONFIG_SPI_FLASH_STMICRO
241#define CONFIG_CMD_SF
242#define CONFIG_SF_DEFAULT_SPEED 10000000
243#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
244
245/*
246 * General PCI
247 * Memory space is mapped 1-1, but I/O space must start from 0.
248 */
249#if defined(CONFIG_PCI)
250
251/* controller 3, Slot 3, tgtid 3, Base address 8000 */
252#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
253#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
254#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
255#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
256#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc10000
257#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
258#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc10000
259#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
260
261/* controller 2, Slot 2, tgtid 2, Base address 9000 */
262#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
263#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
264#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
265#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
266#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc20000
267#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
268#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc20000
269#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
270
271/* controller 1, Slot 1, tgtid 1, Base address a000 */
272#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
273#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
274#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
275#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
276#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc30000
277#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
278#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc30000
279#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
280
281#define CONFIG_PCI_PNP /* do pci plug-and-play */
282
283#undef CONFIG_EEPRO100
284#undef CONFIG_TULIP
285#undef CONFIG_RTL8139
286
287#ifdef CONFIG_RTL8139
288/* This macro is used by RTL8139 but not defined in PPC architecture */
289#define KSEG1ADDR(x) (x)
290#define _IO_BASE 0x00000000
291#endif
292
Ira W. Snyder98397092011-11-23 08:25:58 -0800293#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
294#define CONFIG_DOS_PARTITION
295
296#endif /* CONFIG_PCI */
297
298#if defined(CONFIG_TSEC_ENET)
299#define CONFIG_MII 1 /* MII PHY management */
300#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
301#define CONFIG_TSEC1 1
302#define CONFIG_TSEC1_NAME "eTSEC1"
303#define CONFIG_TSEC2 1
304#define CONFIG_TSEC2_NAME "eTSEC2"
305#define CONFIG_TSEC3 1
306#define CONFIG_TSEC3_NAME "eTSEC3"
307
308#define TSEC1_PHY_ADDR 0
309#define TSEC2_PHY_ADDR 2
310#define TSEC3_PHY_ADDR 1
311
312#undef CONFIG_VSC7385_ENET
313
314#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
315#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
316#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
317
318#define TSEC1_PHYIDX 0
319#define TSEC2_PHYIDX 0
320#define TSEC3_PHYIDX 0
321
322#define CONFIG_ETHPRIME "eTSEC1"
323
324#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
325
326#endif /* CONFIG_TSEC_ENET */
327
328/*
329 * Environment
330 */
331#if defined(CONFIG_RAMBOOT_SDCARD)
332 #define CONFIG_ENV_IS_IN_MMC 1
Fabio Estevam4394d0c2012-01-11 09:20:50 +0000333 #define CONFIG_FSL_FIXED_MMC_LOCATION
Ira W. Snyder98397092011-11-23 08:25:58 -0800334 #define CONFIG_ENV_SIZE 0x2000
335 #define CONFIG_SYS_MMC_ENV_DEV 0
336#elif defined(CONFIG_RAMBOOT_SPIFLASH)
337 #define CONFIG_ENV_IS_IN_SPI_FLASH
338 #define CONFIG_ENV_SPI_BUS 0
339 #define CONFIG_ENV_SPI_CS 0
340 #define CONFIG_ENV_SPI_MAX_HZ 10000000
341 #define CONFIG_ENV_SPI_MODE 0
342 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
343 #define CONFIG_ENV_SECT_SIZE 0x10000
344 #define CONFIG_ENV_SIZE 0x2000
345#endif
346
347#define CONFIG_LOADS_ECHO 1
348#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
349
350/*
351 * Command line configuration.
352 */
353#include <config_cmd_default.h>
354
355#define CONFIG_CMD_ELF
356#define CONFIG_CMD_I2C
357#define CONFIG_CMD_IRQ
358#define CONFIG_CMD_MII
359#define CONFIG_CMD_PING
360#define CONFIG_CMD_SETEXPR
361#define CONFIG_CMD_REGINFO
362
363#if defined(CONFIG_PCI)
364#define CONFIG_CMD_NET
365#define CONFIG_CMD_PCI
366#endif
367
368#undef CONFIG_WATCHDOG /* watchdog disabled */
369
370#define CONFIG_MMC 1
371
372#ifdef CONFIG_MMC
373#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
374#define CONFIG_CMD_MMC
375#define CONFIG_DOS_PARTITION
376#define CONFIG_FSL_ESDHC
377#define CONFIG_GENERIC_MMC
378#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
379#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
380#endif /* CONFIG_MMC */
381
ramneek mehresh3d7506f2012-04-18 19:39:53 +0000382#define CONFIG_HAS_FSL_DR_USB
383#ifdef CONFIG_HAS_FSL_DR_USB
Ira W. Snyder98397092011-11-23 08:25:58 -0800384#define CONFIG_USB_EHCI
385
386#ifdef CONFIG_USB_EHCI
387#define CONFIG_CMD_USB
388#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
389#define CONFIG_USB_EHCI_FSL
390#define CONFIG_USB_STORAGE
ramneek mehresh3d7506f2012-04-18 19:39:53 +0000391#endif
Ira W. Snyder98397092011-11-23 08:25:58 -0800392#endif
393
394#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
395#define CONFIG_CMD_EXT2
396#define CONFIG_CMD_FAT
397#define CONFIG_DOS_PARTITION
398#endif
399
400/* Misc Extra Settings */
Ira W. Snyder98397092011-11-23 08:25:58 -0800401#define CONFIG_CMD_DHCP 1
402
403#define CONFIG_CMD_DATE 1
404#define CONFIG_RTC_M41T62 1
405#define CONFIG_SYS_RTC_BUS_NUM 1
406#define CONFIG_SYS_I2C_RTC_ADDR 0x68
407
408/*
409 * Miscellaneous configurable options
410 */
411#define CONFIG_SYS_LONGHELP /* undef to save memory */
412#define CONFIG_CMDLINE_EDITING /* Command-line editing */
413#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
414#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
Ira W. Snyder98397092011-11-23 08:25:58 -0800415#if defined(CONFIG_CMD_KGDB)
416#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
417#else
418#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
419#endif
420#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
421 /* Print Buffer Size */
422#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
423#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
Ira W. Snyder98397092011-11-23 08:25:58 -0800424
425/*
426 * For booting Linux, the board info and command line data
427 * have to be in the first 64 MB of memory, since this is
428 * the maximum mapped by the Linux kernel during initialization.
429 */
430#define CONFIG_SYS_BOOTMAPSZ (64 << 20)
431#define CONFIG_SYS_BOOTM_LEN (64 << 20)
432
433#if defined(CONFIG_CMD_KGDB)
434#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
435#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
436#endif
437
438/*
439 * Environment Configuration
440 */
441
442/* The mac addresses for all ethernet interface */
443#if defined(CONFIG_TSEC_ENET)
444#define CONFIG_HAS_ETH0
445#define CONFIG_HAS_ETH1
446#define CONFIG_HAS_ETH2
447#define CONFIG_HAS_ETH3
448#endif
449
450#define CONFIG_HOSTNAME unknown
451#define CONFIG_ROOTPATH "/opt/nfsroot"
452#define CONFIG_BOOTFILE "uImage"
453#define CONFIG_UBOOTPATH u-boot.bin
454
455/* default location for tftp and bootm */
456#define CONFIG_LOADADDR 1000000
457
458#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
459#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
460
461#define CONFIG_BAUDRATE 115200
462
463#define CONFIG_EXTRA_ENV_SETTINGS \
464 "hwconfig=fsl_ddr:ecc=on\0" \
465 "bootcmd=run sdboot\0" \
466 "sdboot=setenv bootargs root=/dev/mmcblk0p2 rw " \
467 "rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\
468 "$othbootargs; mmcinfo; " \
469 "ext2load mmc 0:2 $loadaddr /boot/$bootfile; " \
470 "ext2load mmc 0:2 $fdtaddr /boot/$fdtfile; " \
471 "bootm $loadaddr - $fdtaddr\0" \
472 "sdfatboot=setenv bootargs root=/dev/ram rw " \
473 "rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\
474 "$othbootargs; mmcinfo; " \
475 "fatload mmc 0:1 $loadaddr $bootfile; " \
476 "fatload mmc 0:1 $fdtaddr $fdtfile; " \
477 "fatload mmc 0:1 $ramdiskaddr $ramdiskfile; " \
478 "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
479 "usbboot=setenv bootargs root=/dev/sda1 rw " \
480 "rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\
481 "$othbootargs; " \
482 "usb start; " \
483 "ext2load usb 0:1 $loadaddr /boot/$bootfile; " \
484 "ext2load usb 0:1 $fdtaddr /boot/$fdtfile; " \
485 "bootm $loadaddr - $fdtaddr\0" \
486 "usbfatboot=setenv bootargs root=/dev/ram rw " \
487 "console=$consoledev,$baudrate $othbootargs; " \
488 "usb start; " \
489 "fatload usb 0:2 $loadaddr $bootfile; " \
490 "fatload usb 0:2 $fdtaddr $fdtfile; " \
491 "fatload usb 0:2 $ramdiskaddr $ramdiskfile; " \
492 "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
493 "usbext2boot=setenv bootargs root=/dev/ram rw " \
494 "console=$consoledev,$baudrate $othbootargs; " \
495 "usb start; " \
496 "ext2load usb 0:4 $loadaddr $bootfile; " \
497 "ext2load usb 0:4 $fdtaddr $fdtfile; " \
498 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile; " \
499 "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
500 "upgradespi=sf probe 0; " \
501 "setenv startaddr 0; " \
502 "setenv erasesize a0000; " \
503 "tftp 1000000 $tftppath/$uboot_spi; " \
504 "sf erase $startaddr $erasesize; " \
505 "sf write 1000000 $startaddr $filesize; " \
506 "sf erase 100000 120000\0" \
507 "clearspienv=sf probe 0;sf erase 100000 20000\0" \
508 "othbootargs=ramdisk_size=700000 cache-sram-size=0x10000\0" \
509 "netdev=eth0\0" \
510 "rootdelaysecond=15\0" \
511 "uboot_nor=u-boot-nor.bin\0" \
512 "uboot_spi=u-boot-p2020.spi\0" \
513 "uboot_sd=u-boot-p2020.bin\0" \
514 "consoledev=ttyS0\0" \
515 "ramdiskaddr=2000000\0" \
516 "ramdiskfile=rootfs-dev.ext2.img\0" \
517 "fdtaddr=c00000\0" \
518 "fdtfile=uImage-2.6.32-p2020.dtb\0" \
519 "tftppath=p2020\0"
520
521#define CONFIG_HDBOOT \
522 "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
523 "console=$consoledev,$baudrate $othbootargs;" \
524 "usb start;" \
525 "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
526 "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
527 "bootm $loadaddr - $fdtaddr"
528
529#define CONFIG_NFSBOOTCOMMAND \
530 "setenv bootargs root=/dev/nfs rw " \
531 "nfsroot=$serverip:$rootpath " \
532 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off "\
533 "console=$consoledev,$baudrate $othbootargs;" \
534 "tftp $loadaddr $tftppath/$bootfile;" \
535 "tftp $fdtaddr $tftppath/$fdtfile;" \
536 "bootm $loadaddr - $fdtaddr"
537
Wolfgang Denk6b62b9a2011-12-19 12:03:40 +0100538
Ira W. Snyder98397092011-11-23 08:25:58 -0800539#define CONFIG_RAMBOOTCOMMAND \
540 "setenv bootargs root=/dev/ram rw " \
541 "console=$consoledev,$baudrate $othbootargs;" \
542 "tftp $ramdiskaddr $tftppath/$ramdiskfile;" \
543 "tftp $loadaddr $tftppath/$bootfile;" \
544 "tftp $fdtaddr $tftppath/$fdtfile;" \
545 "bootm $loadaddr $ramdiskaddr $fdtaddr"
546
547#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
548
549#endif /* __CONFIG_H */