Tom Rini | 83d290c | 2018-05-06 17:58:06 -0400 | [diff] [blame] | 1 | // SPDX-License-Identifier: GPL-2.0+ |
Matt Porter | f485c8a | 2013-03-20 05:38:13 +0000 | [diff] [blame] | 2 | /* |
| 3 | * ET1011C PHY driver |
| 4 | * |
| 5 | * Derived from Linux kernel driver by Chaithrika U S |
| 6 | * Copyright (C) 2013, Texas Instruments, Incorporated - http://www.ti.com/ |
Matt Porter | f485c8a | 2013-03-20 05:38:13 +0000 | [diff] [blame] | 7 | */ |
| 8 | #include <config.h> |
| 9 | #include <phy.h> |
| 10 | |
| 11 | #define ET1011C_CONFIG_REG (0x16) |
| 12 | #define ET1011C_TX_FIFO_MASK (0x3 << 12) |
| 13 | #define ET1011C_TX_FIFO_DEPTH_8 (0x0 << 12) |
| 14 | #define ET1011C_TX_FIFO_DEPTH_16 (0x1 << 12) |
| 15 | #define ET1011C_INTERFACE_MASK (0x7 << 0) |
| 16 | #define ET1011C_GMII_INTERFACE (0x2 << 0) |
| 17 | #define ET1011C_SYS_CLK_EN (0x1 << 4) |
| 18 | #define ET1011C_TX_CLK_EN (0x1 << 5) |
| 19 | |
| 20 | #define ET1011C_STATUS_REG (0x1A) |
| 21 | #define ET1011C_DUPLEX_STATUS (0x1 << 7) |
| 22 | #define ET1011C_SPEED_MASK (0x3 << 8) |
| 23 | #define ET1011C_SPEED_1000 (0x2 << 8) |
| 24 | #define ET1011C_SPEED_100 (0x1 << 8) |
| 25 | #define ET1011C_SPEED_10 (0x0 << 8) |
| 26 | |
| 27 | static int et1011c_config(struct phy_device *phydev) |
| 28 | { |
| 29 | int ctl = 0; |
| 30 | ctl = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR); |
| 31 | if (ctl < 0) |
| 32 | return ctl; |
| 33 | ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 | |
| 34 | BMCR_ANENABLE); |
| 35 | /* First clear the PHY */ |
| 36 | phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, ctl | BMCR_RESET); |
| 37 | |
| 38 | return genphy_config_aneg(phydev); |
| 39 | } |
| 40 | |
| 41 | static int et1011c_parse_status(struct phy_device *phydev) |
| 42 | { |
| 43 | int mii_reg; |
| 44 | int speed; |
| 45 | |
| 46 | mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, ET1011C_STATUS_REG); |
| 47 | |
| 48 | if (mii_reg & ET1011C_DUPLEX_STATUS) |
| 49 | phydev->duplex = DUPLEX_FULL; |
| 50 | else |
| 51 | phydev->duplex = DUPLEX_HALF; |
| 52 | |
| 53 | speed = mii_reg & ET1011C_SPEED_MASK; |
| 54 | switch (speed) { |
| 55 | case ET1011C_SPEED_1000: |
| 56 | phydev->speed = SPEED_1000; |
| 57 | mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, ET1011C_CONFIG_REG); |
| 58 | mii_reg &= ~ET1011C_TX_FIFO_MASK; |
| 59 | phy_write(phydev, MDIO_DEVAD_NONE, ET1011C_CONFIG_REG, |
| 60 | mii_reg | |
| 61 | ET1011C_GMII_INTERFACE | |
| 62 | ET1011C_SYS_CLK_EN | |
| 63 | #ifdef CONFIG_PHY_ET1011C_TX_CLK_FIX |
| 64 | ET1011C_TX_CLK_EN | |
| 65 | #endif |
| 66 | ET1011C_TX_FIFO_DEPTH_16); |
| 67 | break; |
| 68 | case ET1011C_SPEED_100: |
| 69 | phydev->speed = SPEED_100; |
| 70 | break; |
| 71 | case ET1011C_SPEED_10: |
| 72 | phydev->speed = SPEED_10; |
| 73 | break; |
| 74 | } |
| 75 | |
| 76 | return 0; |
| 77 | } |
| 78 | |
| 79 | static int et1011c_startup(struct phy_device *phydev) |
| 80 | { |
Michal Simek | b733c27 | 2016-05-18 12:46:12 +0200 | [diff] [blame] | 81 | int ret; |
| 82 | |
| 83 | ret = genphy_update_link(phydev); |
| 84 | if (ret) |
| 85 | return ret; |
| 86 | |
| 87 | return et1011c_parse_status(phydev); |
Matt Porter | f485c8a | 2013-03-20 05:38:13 +0000 | [diff] [blame] | 88 | } |
| 89 | |
| 90 | static struct phy_driver et1011c_driver = { |
| 91 | .name = "ET1011C", |
| 92 | .uid = 0x0282f014, |
| 93 | .mask = 0xfffffff0, |
| 94 | .features = PHY_GBIT_FEATURES, |
| 95 | .config = &et1011c_config, |
| 96 | .startup = &et1011c_startup, |
| 97 | }; |
| 98 | |
| 99 | int phy_et1011c_init(void) |
| 100 | { |
| 101 | phy_register(&et1011c_driver); |
| 102 | |
| 103 | return 0; |
| 104 | } |