blob: cfec59e8605003040f71f705c623e7d4e78f4a8e [file] [log] [blame]
Mario Sixddc935f2019-01-21 09:17:40 +01001/* SPDX-License-Identifier: GPL-2.0+ */
2/*
3 * (C) Copyright 2006-2010
4 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 */
6
7/*
8 * mpc8349emds board configuration file
9 *
10 */
11
12#ifndef __CONFIG_H
13#define __CONFIG_H
14
15/*
16 * High Level Configuration Options
17 */
18#define CONFIG_E300 1 /* E300 Family */
19
Mario Sixddc935f2019-01-21 09:17:40 +010020#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
Mario Sixddc935f2019-01-21 09:17:40 +010021
22/*
23 * DDR Setup
24 */
25#define CONFIG_DDR_ECC /* support DDR ECC function */
26#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
27#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
28
29/*
30 * SYS_FSL_DDR2 is selected in Kconfig to use unified DDR driver
31 * unselect it to use old spd_sdram.c
32 */
33#define CONFIG_SYS_SPD_BUS_NUM 0
34#define SPD_EEPROM_ADDRESS1 0x52
35#define SPD_EEPROM_ADDRESS2 0x51
36#define CONFIG_DIMM_SLOTS_PER_CTLR 2
37#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
38#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
39#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
40
41/*
42 * 32-bit data path mode.
43 *
44 * Please note that using this mode for devices with the real density of 64-bit
45 * effectively reduces the amount of available memory due to the effect of
46 * wrapping around while translating address to row/columns, for example in the
47 * 256MB module the upper 128MB get aliased with contents of the lower
48 * 128MB); normally this define should be used for devices with real 32-bit
49 * data path.
50 */
51#undef CONFIG_DDR_32BIT
52
Mario Six8a81bfd2019-01-21 09:18:15 +010053#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory*/
Mario Sixddc935f2019-01-21 09:17:40 +010054#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
55 | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
56#undef CONFIG_DDR_2T_TIMING
57
58/*
59 * DDRCDR - DDR Control Driver Register
60 */
61#define CONFIG_SYS_DDRCDR_VALUE 0x80080001
62
63#if defined(CONFIG_SPD_EEPROM)
64/*
65 * Determine DDR configuration from I2C interface.
66 */
67#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
68#else
69/*
70 * Manually set up DDR parameters
71 */
72#define CONFIG_SYS_DDR_SIZE 256 /* MB */
73#if defined(CONFIG_DDR_II)
74#define CONFIG_SYS_DDRCDR 0x80080001
75#define CONFIG_SYS_DDR_CS2_BNDS 0x0000000f
76#define CONFIG_SYS_DDR_CS2_CONFIG 0x80330102
77#define CONFIG_SYS_DDR_TIMING_0 0x00220802
78#define CONFIG_SYS_DDR_TIMING_1 0x38357322
79#define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8
80#define CONFIG_SYS_DDR_TIMING_3 0x00000000
81#define CONFIG_SYS_DDR_CLK_CNTL 0x02000000
82#define CONFIG_SYS_DDR_MODE 0x47d00432
83#define CONFIG_SYS_DDR_MODE2 0x8000c000
84#define CONFIG_SYS_DDR_INTERVAL 0x03cf0080
85#define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000
86#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
87#else
88#define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \
89 | CSCONFIG_ROW_BIT_13 \
90 | CSCONFIG_COL_BIT_10)
91#define CONFIG_SYS_DDR_TIMING_1 0x36332321
92#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
93#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
94#define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */
95
96#if defined(CONFIG_DDR_32BIT)
97/* set burst length to 8 for 32-bit data path */
98 /* DLL,normal,seq,4/2.5, 8 burst len */
99#define CONFIG_SYS_DDR_MODE 0x00000023
100#else
101/* the default burst length is 4 - for 64-bit data path */
102 /* DLL,normal,seq,4/2.5, 4 burst len */
103#define CONFIG_SYS_DDR_MODE 0x00000022
104#endif
105#endif
106#endif
107
108/*
109 * SDRAM on the Local Bus
110 */
111#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */
112#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
113
114/*
115 * FLASH on the Local Bus
116 */
117#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */
118#define CONFIG_SYS_FLASH_SIZE 32 /* max flash size in MB */
119
Mario Sixddc935f2019-01-21 09:17:40 +0100120#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
121#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
122
123#undef CONFIG_SYS_FLASH_CHECKSUM
124#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
125#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
126
127#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
128
129#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
130#define CONFIG_SYS_RAMBOOT
131#else
132#undef CONFIG_SYS_RAMBOOT
133#endif
134
135/*
136 * BCSR register on local bus 32KB, 8-bit wide for MDS config reg
137 */
138#define CONFIG_SYS_BCSR 0xE2400000
139 /* Access window base at BCSR base */
Mario Sixddc935f2019-01-21 09:17:40 +0100140#define CONFIG_SYS_INIT_RAM_LOCK 1
141#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */
142#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
143
144#define CONFIG_SYS_GBL_DATA_OFFSET \
145 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
146#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
147
148#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
149#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
150
151/*
Mario Sixddc935f2019-01-21 09:17:40 +0100152 * The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory.
153 */
154
155/* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */
156/*
157 * Base Register 2 and Option Register 2 configure SDRAM.
158 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
159 *
160 * For BR2, need:
161 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
162 * port-size = 32-bits = BR2[19:20] = 11
163 * no parity checking = BR2[21:22] = 00
164 * SDRAM for MSEL = BR2[24:26] = 011
165 * Valid = BR[31] = 1
166 *
167 * 0 4 8 12 16 20 24 28
168 * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
169 */
170
Mario Sixddc935f2019-01-21 09:17:40 +0100171/*
172 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
173 *
174 * For OR2, need:
175 * 64MB mask for AM, OR2[0:7] = 1111 1100
176 * XAM, OR2[17:18] = 11
177 * 9 columns OR2[19-21] = 010
178 * 13 rows OR2[23-25] = 100
179 * EAD set for extra time OR[31] = 1
180 *
181 * 0 4 8 12 16 20 24 28
182 * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
183 */
184
Mario Sixddc935f2019-01-21 09:17:40 +0100185
186 /* LB sdram refresh timer, about 6us */
187#define CONFIG_SYS_LBC_LSRT 0x32000000
188 /* LB refresh timer prescal, 266MHz/32 */
189#define CONFIG_SYS_LBC_MRTPR 0x20000000
190
191#define CONFIG_SYS_LBC_LSDMR_COMMON (LSDMR_RFEN \
192 | LSDMR_BSMA1516 \
193 | LSDMR_RFCR8 \
194 | LSDMR_PRETOACT6 \
195 | LSDMR_ACTTORW3 \
196 | LSDMR_BL8 \
197 | LSDMR_WRC3 \
198 | LSDMR_CL3)
199
200/*
201 * SDRAM Controller configuration sequence.
202 */
203#define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
204#define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
205#define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
206#define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
207#define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
208
209/*
210 * Serial Port
211 */
212#define CONFIG_SYS_NS16550_SERIAL
213#define CONFIG_SYS_NS16550_REG_SIZE 1
214#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
215
216#define CONFIG_SYS_BAUDRATE_TABLE \
217 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
218
219#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
220#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
221
222/* I2C */
223#define CONFIG_SYS_I2C
224#define CONFIG_SYS_I2C_FSL
225#define CONFIG_SYS_FSL_I2C_SPEED 400000
226#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
227#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
228#define CONFIG_SYS_FSL_I2C2_SPEED 400000
229#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
230#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
231#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
232
233/* SPI */
234#undef CONFIG_SOFT_SPI /* SPI bit-banged */
235
236/* GPIOs. Used as SPI chip selects */
237#define CONFIG_SYS_GPIO1_PRELIM
238#define CONFIG_SYS_GPIO1_DIR 0xC0000000 /* SPI CS on 0, LED on 1 */
239#define CONFIG_SYS_GPIO1_DAT 0xC0000000 /* Both are active LOW */
240
241/* TSEC */
242#define CONFIG_SYS_TSEC1_OFFSET 0x24000
243#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
244#define CONFIG_SYS_TSEC2_OFFSET 0x25000
245#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
246
247/* USB */
248#define CONFIG_SYS_USE_MPC834XSYS_USB_PHY 1 /* Use SYS board PHY */
249
250/*
251 * General PCI
252 * Addresses are mapped 1-1.
253 */
254#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
255#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
256#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
257#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
258#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
259#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
260#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
261#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
262#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
263
264#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
265#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
266#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
267#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
268#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
269#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
270#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
271#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
272#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
273
274#if defined(CONFIG_PCI)
275
Mario Sixddc935f2019-01-21 09:17:40 +0100276#define CONFIG_83XX_PCI_STREAMING
277
Mario Sixddc935f2019-01-21 09:17:40 +0100278
279#if !defined(CONFIG_PCI_PNP)
280 #define PCI_ENET0_IOADDR 0xFIXME
281 #define PCI_ENET0_MEMADDR 0xFIXME
282 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
283#endif
284
285#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
286#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
287
288#endif /* CONFIG_PCI */
289
290/*
291 * TSEC configuration
292 */
293
294#if defined(CONFIG_TSEC_ENET)
295
296#define CONFIG_GMII 1 /* MII PHY management */
297#define CONFIG_TSEC1 1
298#define CONFIG_TSEC1_NAME "TSEC0"
299#define CONFIG_TSEC2 1
300#define CONFIG_TSEC2_NAME "TSEC1"
301#define TSEC1_PHY_ADDR 0
302#define TSEC2_PHY_ADDR 1
303#define TSEC1_PHYIDX 0
304#define TSEC2_PHYIDX 0
305#define TSEC1_FLAGS TSEC_GIGABIT
306#define TSEC2_FLAGS TSEC_GIGABIT
307
308/* Options are: TSEC[0-1] */
309#define CONFIG_ETHPRIME "TSEC0"
310
311#endif /* CONFIG_TSEC_ENET */
312
313/*
314 * Configure on-board RTC
315 */
316#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
317#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
318
319/*
320 * Environment
321 */
322#ifndef CONFIG_SYS_RAMBOOT
Mario Sixddc935f2019-01-21 09:17:40 +0100323/* Address and size of Redundant Environment Sector */
Mario Sixddc935f2019-01-21 09:17:40 +0100324#endif
325
326#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
327#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
328
329/*
330 * BOOTP options
331 */
332#define CONFIG_BOOTP_BOOTFILESIZE
333
Mario Sixddc935f2019-01-21 09:17:40 +0100334#undef CONFIG_WATCHDOG /* watchdog disabled */
335
336/*
337 * Miscellaneous configurable options
338 */
339#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
340
341/*
342 * For booting Linux, the board info and command line data
343 * have to be in the first 256 MB of memory, since this is
344 * the maximum mapped by the Linux kernel during initialization.
345 */
346 /* Initial Memory map for Linux*/
347#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
348#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
349
350#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
351
Mario Sixddc935f2019-01-21 09:17:40 +0100352/*
353 * System performance
354 */
Mario Sixddc935f2019-01-21 09:17:40 +0100355#define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */
356#define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */
357#define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */
358#define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */
359
360/* System IO Config */
361#define CONFIG_SYS_SICRH 0
362#define CONFIG_SYS_SICRL SICRL_LDP_A
363
Mario Sixddc935f2019-01-21 09:17:40 +0100364#ifdef CONFIG_PCI
365#define CONFIG_PCI_INDIRECT_BRIDGE
Mario Sixddc935f2019-01-21 09:17:40 +0100366#endif
367
Mario Sixddc935f2019-01-21 09:17:40 +0100368#if defined(CONFIG_CMD_KGDB)
369#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
370#endif
371
372/*
373 * Environment Configuration
374 */
Mario Sixddc935f2019-01-21 09:17:40 +0100375
376#if defined(CONFIG_TSEC_ENET)
377#define CONFIG_HAS_ETH1
378#define CONFIG_HAS_ETH0
379#endif
380
381#define CONFIG_HOSTNAME "mpc8349emds"
382#define CONFIG_ROOTPATH "/nfsroot/rootfs"
383#define CONFIG_BOOTFILE "uImage"
384
385#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
386
Mario Sixddc935f2019-01-21 09:17:40 +0100387#define CONFIG_EXTRA_ENV_SETTINGS \
388 "netdev=eth0\0" \
389 "hostname=mpc8349emds\0" \
390 "nfsargs=setenv bootargs root=/dev/nfs rw " \
391 "nfsroot=${serverip}:${rootpath}\0" \
392 "ramargs=setenv bootargs root=/dev/ram rw\0" \
393 "addip=setenv bootargs ${bootargs} " \
394 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
395 ":${hostname}:${netdev}:off panic=1\0" \
396 "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
397 "flash_nfs=run nfsargs addip addtty;" \
398 "bootm ${kernel_addr}\0" \
399 "flash_self=run ramargs addip addtty;" \
400 "bootm ${kernel_addr} ${ramdisk_addr}\0" \
401 "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
402 "bootm\0" \
403 "load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0" \
404 "update=protect off fe000000 fe03ffff; " \
405 "era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\
406 "upd=run load update\0" \
407 "fdtaddr=780000\0" \
408 "fdtfile=mpc834x_mds.dtb\0" \
409 ""
410
411#define CONFIG_NFSBOOTCOMMAND \
412 "setenv bootargs root=/dev/nfs rw " \
413 "nfsroot=$serverip:$rootpath " \
414 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
415 "$netdev:off " \
416 "console=$consoledev,$baudrate $othbootargs;" \
417 "tftp $loadaddr $bootfile;" \
418 "tftp $fdtaddr $fdtfile;" \
419 "bootm $loadaddr - $fdtaddr"
420
421#define CONFIG_RAMBOOTCOMMAND \
422 "setenv bootargs root=/dev/ram rw " \
423 "console=$consoledev,$baudrate $othbootargs;" \
424 "tftp $ramdiskaddr $ramdiskfile;" \
425 "tftp $loadaddr $bootfile;" \
426 "tftp $fdtaddr $fdtfile;" \
427 "bootm $loadaddr $ramdiskaddr $fdtaddr"
428
429#define CONFIG_BOOTCOMMAND "run flash_self"
430
431#endif /* __CONFIG_H */