cpu/mpc8xx/scc.c

/*
 * File:  scc.c
 * Description:
 * 	Basic ET HW initialization and packet RX/TX routines
 *
 * NOTE  <<<IMPORTANT:  PLEASE READ>>>:
 *     Do not cache Rx/Tx buffers!
 */

/*
 * MPC823 <-> MC68160 Connections:
 *
 * Setup MPC823 to work with MC68160 Enhanced Ethernet
 * Serial Tranceiver as follows:
 *
 * MPC823 Signal                MC68160  Comments
 * ------ ------                -------  --------
 * PA-12 ETHTX    -------->   TX       Eth. Port Transmit Data
 * PB-18 E_TENA   -------->   TENA     Eth. Transmit Port Enable
 * PA-5 ETHTCK    <--------   TCLK     Eth. Port Transmit Clock
 * PA-13 ETHRX    <--------   RX       Eth. Port Receive Data
 * PC-8 E_RENA    <--------   RENA     Eth. Receive Enable
 * PA-6 ETHRCK    <--------   RCLK     Eth. Port Receive Clock
 * PC-9 E_CLSN    <--------   CLSN     Eth. Port Collision Indication
 *
 * FADS Board Signal              MC68160  Comments
 * -----------------              -------  --------
 * (BCSR1) ETHEN*     -------->  CS2      Eth. Port Enable
 * (BSCR4) TPSQEL*    -------->  TPSQEL   Twisted Pair Signal Quality Error Test Enable
 * (BCSR4) TPFLDL*    -------->  TPFLDL   Twisted Pair Full-Duplex
 * (BCSR4) ETHLOOP    -------->  LOOP     Eth. Port Diagnostic Loop-Back
 *
 */

#include <common.h>
#include <malloc.h>
#include <commproc.h>
#include <net.h>
#include <command.h>

#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(SCC_ENET)

/* Ethernet Transmit and Receive Buffers */
#define DBUF_LENGTH  1520

#define TX_BUF_CNT 2

#define TOUT_LOOP 100

static char txbuf[DBUF_LENGTH];

static uint rxIdx;	/* index of the current RX buffer */
static uint txIdx;	/* index of the current TX buffer */

/*
  * SCC Ethernet Tx and Rx buffer descriptors allocated at the
  *  immr->udata_bd address on Dual-Port RAM
  * Provide for Double Buffering
  */

typedef volatile struct CommonBufferDescriptor {
    cbd_t rxbd[PKTBUFSRX];	/* Rx BD */
    cbd_t txbd[TX_BUF_CNT];	/* Tx BD */
} RTXBD;

static RTXBD *rtx;

static int scc_send(struct eth_device* dev, volatile void *packet, int length);
static int scc_recv(struct eth_device* dev);
static int scc_init (struct eth_device* dev, bd_t * bd);
static void scc_halt(struct eth_device* dev);

int scc_initialize(bd_t *bis)
{
	struct eth_device* dev;

	dev = (struct eth_device*) malloc(sizeof *dev);
	memset(dev, 0, sizeof *dev);

	sprintf(dev->name, "SCC ETHERNET");
	dev->iobase = 0;
	dev->priv   = 0;
	dev->init   = scc_init;
	dev->halt   = scc_halt;
	dev->send   = scc_send;
	dev->recv   = scc_recv;

	eth_register(dev);

	return 1;
}

static int scc_send(struct eth_device* dev, volatile void *packet, int length)
{
	int i, j=0;
#if 0
	volatile char *in, *out;
#endif

	/* section 16.9.23.3
	 * Wait for ready
	 */
#if 0
	while (rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY);
	out = (char *)(rtx->txbd[txIdx].cbd_bufaddr);
	in = packet;
	for(i = 0; i < length; i++) {
		*out++ = *in++;
	}
	rtx->txbd[txIdx].cbd_datlen = length;
	rtx->txbd[txIdx].cbd_sc |= (BD_ENET_TX_READY | BD_ENET_TX_LAST);
	while (rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) j++;

#ifdef ET_DEBUG
	printf("cycles: %d    status: %x\n", j, rtx->txbd[txIdx].cbd_sc);
#endif
	i = (rtx->txbd[txIdx++].cbd_sc & BD_ENET_TX_STATS) /* return only status bits */;

	/* wrap around buffer index when necessary */
	if (txIdx >= TX_BUF_CNT) txIdx = 0;
#endif

	while ((rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) && (j<TOUT_LOOP)) {
		udelay (1);	/* will also trigger Wd if needed */
		j++;
	}
	if (j>=TOUT_LOOP) printf("TX not ready\n");
	rtx->txbd[txIdx].cbd_bufaddr = (uint)packet;
	rtx->txbd[txIdx].cbd_datlen = length;
	rtx->txbd[txIdx].cbd_sc |= (BD_ENET_TX_READY | BD_ENET_TX_LAST |BD_ENET_TX_WRAP);
	while ((rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) && (j<TOUT_LOOP)) {
		udelay (1);	/* will also trigger Wd if needed */
		j++;
	}
	if (j>=TOUT_LOOP) printf("TX timeout\n");
#ifdef ET_DEBUG
	printf("cycles: %d    status: %x\n", j, rtx->txbd[txIdx].cbd_sc);
#endif
	i = (rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_STATS) /* return only status bits */;
	return i;
}

static int scc_recv(struct eth_device* dev)
{
	int length;

   for (;;) {
	/* section 16.9.23.2 */
	if (rtx->rxbd[rxIdx].cbd_sc & BD_ENET_RX_EMPTY) {
		length = -1;
		break;     /* nothing received - leave for() loop */
	}

	length = rtx->rxbd[rxIdx].cbd_datlen;

	if (rtx->rxbd[rxIdx].cbd_sc & 0x003f) {
#ifdef ET_DEBUG
		printf("err: %x\n", rtx->rxbd[rxIdx].cbd_sc);
#endif
	} else {
		/* Pass the packet up to the protocol layers. */
		NetReceive(NetRxPackets[rxIdx], length - 4);
	}


	/* Give the buffer back to the SCC. */
	rtx->rxbd[rxIdx].cbd_datlen = 0;

	/* wrap around buffer index when necessary */
	if ((rxIdx + 1) >= PKTBUFSRX) {
	   rtx->rxbd[PKTBUFSRX - 1].cbd_sc = (BD_ENET_RX_WRAP | BD_ENET_RX_EMPTY);
	   rxIdx = 0;
	} else {
	   rtx->rxbd[rxIdx].cbd_sc = BD_ENET_RX_EMPTY;
	   rxIdx++;
	}
   }
   return length;
}

/**************************************************************
  *
  * SCC Ethernet Initialization Routine
  *
  *************************************************************/

static int scc_init(struct eth_device* dev, bd_t *bis)
{

    int i;
    scc_enet_t *pram_ptr;

    volatile immap_t *immr = (immap_t *)CFG_IMMR;

#ifdef CONFIG_FADS
#if defined(CONFIG_MPC86xADS) || defined(CONFIG_MPC860T)
    /* The MPC86xADS/FADS860T don't use the MODEM_EN or DATA_VOICE signals. */
    *((uint *) BCSR4) &= ~BCSR4_ETHLOOP;
    *((uint *) BCSR4) |= BCSR4_TFPLDL|BCSR4_TPSQEL;
    *((uint *) BCSR1) &= ~BCSR1_ETHEN;
#else
    *((uint *) BCSR4) &= ~(BCSR4_ETHLOOP|BCSR4_MODEM_EN);
    *((uint *) BCSR4) |= BCSR4_TFPLDL|BCSR4_TPSQEL|BCSR4_DATA_VOICE;
    *((uint *) BCSR1) &= ~BCSR1_ETHEN;
#endif
#endif

    pram_ptr = (scc_enet_t *)&(immr->im_cpm.cp_dparam[PROFF_ENET]);

    rxIdx = 0;
    txIdx = 0;

#ifdef CFG_ALLOC_DPRAM
    rtx = (RTXBD *) (immr->im_cpm.cp_dpmem +
		     dpram_alloc_align(sizeof(RTXBD), 8));
#else
    rtx = (RTXBD *) (immr->im_cpm.cp_dpmem + CPM_SCC_BASE);
#endif	/* 0 */

#if (defined(PA_ENET_RXD) && defined(PA_ENET_TXD))
    /* Configure port A pins for Txd and Rxd.
    */
    immr->im_ioport.iop_papar |=  (PA_ENET_RXD | PA_ENET_TXD);
    immr->im_ioport.iop_padir &= ~(PA_ENET_RXD | PA_ENET_TXD);
    immr->im_ioport.iop_paodr &=                ~PA_ENET_TXD;
#elif (defined(PB_ENET_RXD) && defined(PB_ENET_TXD))
    /* Configure port B pins for Txd and Rxd.
    */
    immr->im_cpm.cp_pbpar |=  (PB_ENET_RXD | PB_ENET_TXD);
    immr->im_cpm.cp_pbdir &= ~(PB_ENET_RXD | PB_ENET_TXD);
    immr->im_cpm.cp_pbodr &=                ~PB_ENET_TXD;
#else
#error Configuration Error: exactly ONE of PA_ENET_[RT]XD, PB_ENET_[RT]XD must be defined
#endif

#if defined(PC_ENET_LBK)
    /* Configure port C pins to disable External Loopback
     */
    immr->im_ioport.iop_pcpar &= ~PC_ENET_LBK;
    immr->im_ioport.iop_pcdir |=  PC_ENET_LBK;
    immr->im_ioport.iop_pcso  &= ~PC_ENET_LBK;
    immr->im_ioport.iop_pcdat &= ~PC_ENET_LBK; /* Disable Loopback */
#endif	/* PC_ENET_LBK */

    /* Configure port C pins to enable CLSN and RENA.
    */
    immr->im_ioport.iop_pcpar &= ~(PC_ENET_CLSN | PC_ENET_RENA);
    immr->im_ioport.iop_pcdir &= ~(PC_ENET_CLSN | PC_ENET_RENA);
    immr->im_ioport.iop_pcso  |=  (PC_ENET_CLSN | PC_ENET_RENA);

    /* Configure port A for TCLK and RCLK.
    */
    immr->im_ioport.iop_papar |=  (PA_ENET_TCLK | PA_ENET_RCLK);
    immr->im_ioport.iop_padir &= ~(PA_ENET_TCLK | PA_ENET_RCLK);

    /*
     * Configure Serial Interface clock routing -- see section 16.7.5.3
     * First, clear all SCC bits to zero, then set the ones we want.
     */

    immr->im_cpm.cp_sicr &= ~SICR_ENET_MASK;
    immr->im_cpm.cp_sicr |= SICR_ENET_CLKRT;


    /*
     * Initialize SDCR -- see section 16.9.23.7
     * SDMA configuration register
     */
    immr->im_siu_conf.sc_sdcr = 0x01;


    /*
     * Setup SCC Ethernet Parameter RAM
     */

    pram_ptr->sen_genscc.scc_rfcr = 0x18;  /* Normal Operation and Mot byte ordering */
    pram_ptr->sen_genscc.scc_tfcr = 0x18;  /* Mot byte ordering, Normal access */

    pram_ptr->sen_genscc.scc_mrblr = DBUF_LENGTH;	/* max. ET package len 1520 */

    pram_ptr->sen_genscc.scc_rbase = (unsigned int)(&rtx->rxbd[0]);      /* Set RXBD tbl start at Dual Port */
    pram_ptr->sen_genscc.scc_tbase = (unsigned int)(&rtx->txbd[0]);      /* Set TXBD tbl start at Dual Port */

    /*
     * Setup Receiver Buffer Descriptors (13.14.24.18)
     * Settings:
     *     Empty, Wrap
     */

    for (i = 0; i < PKTBUFSRX; i++)
    {
      rtx->rxbd[i].cbd_sc = BD_ENET_RX_EMPTY;
      rtx->rxbd[i].cbd_datlen = 0;                                 /* Reset */
      rtx->rxbd[i].cbd_bufaddr = (uint)NetRxPackets[i];
    }

    rtx->rxbd[PKTBUFSRX - 1].cbd_sc |= BD_ENET_RX_WRAP;

    /*
     * Setup Ethernet Transmitter Buffer Descriptors (13.14.24.19)
     * Settings:
     *    Add PADs to Short FRAMES, Wrap, Last, Tx CRC
     */

    for (i = 0; i < TX_BUF_CNT; i++)
    {
      rtx->txbd[i].cbd_sc = (BD_ENET_TX_PAD | BD_ENET_TX_LAST | BD_ENET_TX_TC);
      rtx->txbd[i].cbd_datlen = 0;                                 /* Reset */
      rtx->txbd[i].cbd_bufaddr = (uint) (&txbuf[0]);
    }

    rtx->txbd[TX_BUF_CNT - 1].cbd_sc |= BD_ENET_TX_WRAP;

    /*
     * Enter Command:  Initialize Rx Params for SCC
     */

    do {				/* Spin until ready to issue command	*/
	__asm__ ("eieio");
    } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
    /* Issue command */
    immr->im_cpm.cp_cpcr = ((CPM_CR_INIT_RX << 8) | (CPM_CR_ENET << 4) | CPM_CR_FLG);
    do {				/* Spin until command processed		*/
	__asm__ ("eieio");
    } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);

    /*
     * Ethernet Specific Parameter RAM
     *     see table 13-16, pg. 660,
     *     pg. 681 (example with suggested settings)
     */

    pram_ptr->sen_cpres  = ~(0x0);	/* Preset CRC */
    pram_ptr->sen_cmask  = 0xdebb20e3;	/* Constant Mask for CRC */
    pram_ptr->sen_crcec  = 0x0;		/* Error Counter CRC (unused) */
    pram_ptr->sen_alec   = 0x0;		/* Alignment Error Counter (unused) */
    pram_ptr->sen_disfc  = 0x0;		/* Discard Frame Counter (unused) */
    pram_ptr->sen_pads   = 0x8888;	/* Short Frame PAD Characters */

    pram_ptr->sen_retlim = 15;		/* Retry Limit Threshold */
    pram_ptr->sen_maxflr = 1518;	/* MAX Frame Length Register */
    pram_ptr->sen_minflr = 64;		/* MIN Frame Length Register */

    pram_ptr->sen_maxd1  = DBUF_LENGTH;	/* MAX DMA1 Length Register */
    pram_ptr->sen_maxd2  = DBUF_LENGTH;	/* MAX DMA2 Length Register */

    pram_ptr->sen_gaddr1 = 0x0;		/* Group Address Filter 1 (unused) */
    pram_ptr->sen_gaddr2 = 0x0;		/* Group Address Filter 2 (unused) */
    pram_ptr->sen_gaddr3 = 0x0;		/* Group Address Filter 3 (unused) */
    pram_ptr->sen_gaddr4 = 0x0;		/* Group Address Filter 4 (unused) */

#define ea eth_get_dev()->enetaddr
    pram_ptr->sen_paddrh = (ea[5] << 8) + ea[4];
    pram_ptr->sen_paddrm = (ea[3] << 8) + ea[2];
    pram_ptr->sen_paddrl = (ea[1] << 8) + ea[0];
#undef ea

    pram_ptr->sen_pper   = 0x0;		/* Persistence (unused) */
    pram_ptr->sen_iaddr1 = 0x0;		/* Individual Address Filter 1 (unused) */
    pram_ptr->sen_iaddr2 = 0x0;		/* Individual Address Filter 2 (unused) */
    pram_ptr->sen_iaddr3 = 0x0;		/* Individual Address Filter 3 (unused) */
    pram_ptr->sen_iaddr4 = 0x0;		/* Individual Address Filter 4 (unused) */
    pram_ptr->sen_taddrh = 0x0;		/* Tmp Address (MSB) (unused) */
    pram_ptr->sen_taddrm = 0x0;		/* Tmp Address (unused) */
    pram_ptr->sen_taddrl = 0x0;		/* Tmp Address (LSB) (unused) */

    /*
     * Enter Command:  Initialize Tx Params for SCC
     */

    do {				/* Spin until ready to issue command	*/
	__asm__ ("eieio");
    } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
    /* Issue command */
    immr->im_cpm.cp_cpcr = ((CPM_CR_INIT_TX << 8) | (CPM_CR_ENET << 4) | CPM_CR_FLG);
    do {				/* Spin until command processed		*/
	__asm__ ("eieio");
    } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);

    /*
     * Mask all Events in SCCM - we use polling mode
     */
    immr->im_cpm.cp_scc[SCC_ENET].scc_sccm = 0;

    /*
     * Clear Events in SCCE -- Clear bits by writing 1's
     */

    immr->im_cpm.cp_scc[SCC_ENET].scc_scce = ~(0x0);


    /*
     * Initialize GSMR High 32-Bits
     * Settings:  Normal Mode
     */

    immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrh = 0;

    /*
     * Initialize GSMR Low 32-Bits, but do not Enable Transmit/Receive
     * Settings:
     *     TCI = Invert
     *     TPL =  48 bits
     *     TPP = Repeating 10's
     *     MODE = Ethernet
     */

    immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl = (	SCC_GSMRL_TCI	 |	\
						SCC_GSMRL_TPL_48 |	\
						SCC_GSMRL_TPP_10 |	\
						SCC_GSMRL_MODE_ENET);

    /*
     * Initialize the DSR -- see section 13.14.4 (pg. 513) v0.4
     */

    immr->im_cpm.cp_scc[SCC_ENET].scc_dsr = 0xd555;

    /*
     * Initialize the PSMR
     * Settings:
     *	CRC = 32-Bit CCITT
     *	NIB = Begin searching for SFD 22 bits after RENA
     *	FDE = Full Duplex Enable
     *	LPB = Loopback Enable (Needed when FDE is set)
     *	BRO = Reject broadcast packets
     *	PROMISCOUS = Catch all packets regardless of dest. MAC adress
     */
    immr->im_cpm.cp_scc[SCC_ENET].scc_psmr  =	SCC_PSMR_ENCRC	|
						SCC_PSMR_NIB22	|
#if defined(CONFIG_SCC_ENET_FULL_DUPLEX)
						SCC_PSMR_FDE	|
						SCC_PSMR_LPB	|
#endif
#if defined(CONFIG_SCC_ENET_NO_BROADCAST)
						SCC_PSMR_BRO	|
#endif
#if defined(CONFIG_SCC_ENET_PROMISCOUS)
						SCC_PSMR_PRO	|
#endif
						0;

    /*
     * Configure Ethernet TENA Signal
     */

#if (defined(PC_ENET_TENA) && !defined(PB_ENET_TENA))
    immr->im_ioport.iop_pcpar |=  PC_ENET_TENA;
    immr->im_ioport.iop_pcdir &= ~PC_ENET_TENA;
#elif (defined(PB_ENET_TENA) && !defined(PC_ENET_TENA))
    immr->im_cpm.cp_pbpar |= PB_ENET_TENA;
    immr->im_cpm.cp_pbdir |= PB_ENET_TENA;
#else
#error Configuration Error: exactly ONE of PB_ENET_TENA, PC_ENET_TENA must be defined
#endif

#if defined(CONFIG_ADS) && defined(CONFIG_MPC860)
    /*
     * Port C is used to control the PHY,MC68160.
     */
    immr->im_ioport.iop_pcdir |=
	(PC_ENET_ETHLOOP | PC_ENET_TPFLDL | PC_ENET_TPSQEL);

    immr->im_ioport.iop_pcdat |= PC_ENET_TPFLDL;
    immr->im_ioport.iop_pcdat &= ~(PC_ENET_ETHLOOP | PC_ENET_TPSQEL);
    *((uint *) BCSR1) &= ~BCSR1_ETHEN;
#endif	/* MPC860ADS */

#if defined(CONFIG_AMX860)
    /*
     * Port B is used to control the PHY,MC68160.
     */
    immr->im_cpm.cp_pbdir |=
	(PB_ENET_ETHLOOP | PB_ENET_TPFLDL | PB_ENET_TPSQEL);

    immr->im_cpm.cp_pbdat |= PB_ENET_TPFLDL;
    immr->im_cpm.cp_pbdat &= ~(PB_ENET_ETHLOOP | PB_ENET_TPSQEL);

    immr->im_ioport.iop_pddir |= PD_ENET_ETH_EN;
    immr->im_ioport.iop_pddat &= ~PD_ENET_ETH_EN;
#endif  /* AMX860 */

#ifdef CONFIG_RPXCLASSIC
    *((uchar *)BCSR0) &= ~BCSR0_ETHLPBK;
    *((uchar *)BCSR0) |= (BCSR0_ETHEN | BCSR0_COLTEST | BCSR0_FULLDPLX);
#endif

#ifdef CONFIG_RPXLITE
    *((uchar *)BCSR0) |= BCSR0_ETHEN ;
#endif

#ifdef CONFIG_MBX
    board_ether_init();
#endif

#if defined(CONFIG_NETVIA)
#if defined(PA_ENET_PDN)
    immr->im_ioport.iop_papar &= ~PA_ENET_PDN;
    immr->im_ioport.iop_padir |=  PA_ENET_PDN;
    immr->im_ioport.iop_padat |=  PA_ENET_PDN;
#elif defined(PB_ENET_PDN)
    immr->im_cpm.cp_pbpar &= ~PB_ENET_PDN;
    immr->im_cpm.cp_pbdir |=  PB_ENET_PDN;
    immr->im_cpm.cp_pbdat |=  PB_ENET_PDN;
#elif defined(PC_ENET_PDN)
    immr->im_ioport.iop_pcpar &= ~PC_ENET_PDN;
    immr->im_ioport.iop_pcdir |=  PC_ENET_PDN;
    immr->im_ioport.iop_pcdat |=  PC_ENET_PDN;
#elif defined(PD_ENET_PDN)
    immr->im_ioport.iop_pdpar &= ~PD_ENET_PDN;
    immr->im_ioport.iop_pddir |=  PD_ENET_PDN;
    immr->im_ioport.iop_pddat |=  PD_ENET_PDN;
#endif
#endif

    /*
     * Set the ENT/ENR bits in the GSMR Low -- Enable Transmit/Receive
     */

    immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);

    /*
     * Work around transmit problem with first eth packet
     */
#if defined (CONFIG_FADS)
    udelay(10000);	/* wait 10 ms */
#elif defined (CONFIG_AMX860) || defined(CONFIG_RPXCLASSIC)
    udelay(100000);	/* wait 100 ms */
#endif

    return 1;
}


static void scc_halt(struct eth_device* dev)
{
    volatile immap_t *immr = (immap_t *)CFG_IMMR;
    immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
}

#if 0
void restart(void)
{
   volatile immap_t *immr = (immap_t *)CFG_IMMR;
   immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
}
#endif

#endif	/* CFG_CMD_NET, SCC_ENET */