blob: 0f289cb0780d9aa57b1509b68b3df6d884ca4894 [file] [log] [blame]
Yuantian Tang353f36d2019-04-10 16:43:34 +08001/* SPDX-License-Identifier: GPL-2.0+ */
2/*
3 * Copyright 2019 NXP
4 */
5
6#ifndef __LS1028A_RDB_H
7#define __LS1028A_RDB_H
8
9#include "ls1028a_common.h"
10
11#define CONFIG_SYS_CLK_FREQ 100000000
12#define CONFIG_DDR_CLK_FREQ 100000000
13#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ / 4)
14
15#define CONFIG_SYS_RTC_BUS_NUM 0
16
17/* Store environment at top of flash */
Yuantian Tang353f36d2019-04-10 16:43:34 +080018
19#define CONFIG_DIMM_SLOTS_PER_CTLR 1
20
21#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
22
23#define CONFIG_QIXIS_I2C_ACCESS
Yuantian Tang353f36d2019-04-10 16:43:34 +080024
25/*
26 * QIXIS Definitions
27 */
28#define CONFIG_FSL_QIXIS
29
30#ifdef CONFIG_FSL_QIXIS
31#define QIXIS_BASE 0x7fb00000
32#define QIXIS_BASE_PHYS QIXIS_BASE
33#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
34#define QIXIS_LBMAP_SWITCH 2
35#define QIXIS_LBMAP_MASK 0xe0
36#define QIXIS_LBMAP_SHIFT 0x5
37#define QIXIS_LBMAP_DFLTBANK 0x00
38#define QIXIS_LBMAP_ALTBANK 0x00
39#define QIXIS_LBMAP_SD 0x00
40#define QIXIS_LBMAP_EMMC 0x00
41#define QIXIS_LBMAP_QSPI 0x00
42#define QIXIS_RCW_SRC_SD 0xf8
43#define QIXIS_RCW_SRC_EMMC 0xf9
44#define QIXIS_RCW_SRC_QSPI 0xff
45#define QIXIS_RST_CTL_RESET 0x31
46#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x10
47#define QIXIS_RCFG_CTL_RECONFIG_START 0x11
48#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
49#define QIXIS_RST_FORCE_MEM 0x01
50
51#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
52#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
53 CSPR_PORT_SIZE_8 | \
54 CSPR_MSEL_GPCM | \
55 CSPR_V)
56#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
57 CSOR_NOR_NOR_MODE_AVD_NOR | \
58 CSOR_NOR_TRHZ_80)
59#endif
60
61/* SATA */
62#ifndef CONFIG_CMD_EXT2
63#define CONFIG_CMD_EXT2
64#endif
65#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
66#define CONFIG_SYS_SCSI_MAX_LUN 1
67#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
68 CONFIG_SYS_SCSI_MAX_LUN)
69#define SCSI_VEND_ID 0x1b4b
70#define SCSI_DEV_ID 0x9170
71#define CONFIG_SCSI_DEV_LIST {SCSI_VEND_ID, SCSI_DEV_ID}
72#define CONFIG_SCSI_AHCI_PLAT
73#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
74
Yuantian Tanga023c3c2020-03-20 14:37:07 +080075/* Initial environment variables */
76#ifndef SPL_NO_ENV
77#undef CONFIG_EXTRA_ENV_SETTINGS
78#define CONFIG_EXTRA_ENV_SETTINGS \
79 "board=ls1028ardb\0" \
80 "hwconfig=fsl_ddr:bank_intlv=auto\0" \
81 "ramdisk_addr=0x800000\0" \
82 "ramdisk_size=0x2000000\0" \
83 "bootm_size=0x10000000\0" \
84 "fdt_addr=0x00f00000\0" \
85 "kernel_addr=0x01000000\0" \
86 "scriptaddr=0x80000000\0" \
87 "scripthdraddr=0x80080000\0" \
88 "fdtheader_addr_r=0x80100000\0" \
89 "kernelheader_addr_r=0x80200000\0" \
90 "load_addr=0xa0000000\0" \
91 "kernel_addr_r=0x81000000\0" \
92 "fdt_addr_r=0x90000000\0" \
93 "ramdisk_addr_r=0xa0000000\0" \
94 "kernel_start=0x1000000\0" \
95 "kernelheader_start=0x600000\0" \
96 "kernel_load=0xa0000000\0" \
97 "kernel_size=0x2800000\0" \
98 "kernelheader_size=0x40000\0" \
99 "kernel_addr_sd=0x8000\0" \
100 "kernel_size_sd=0x14000\0" \
101 "kernelhdr_addr_sd=0x3000\0" \
102 "kernelhdr_size_sd=0x20\0" \
103 "console=ttyS0,115200\0" \
104 "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
105 BOOTENV \
106 "boot_scripts=ls1028ardb_boot.scr\0" \
107 "boot_script_hdr=hdr_ls1028ardb_bs.out\0" \
108 "scan_dev_for_boot_part=" \
109 "part list ${devtype} ${devnum} devplist; " \
110 "env exists devplist || setenv devplist 1; " \
111 "for distro_bootpart in ${devplist}; do " \
112 "if fstype ${devtype} " \
113 "${devnum}:${distro_bootpart} " \
114 "bootfstype; then " \
115 "run scan_dev_for_boot; " \
116 "fi; " \
117 "done\0" \
118 "scan_dev_for_boot=" \
119 "echo Scanning ${devtype} " \
120 "${devnum}:${distro_bootpart}...; " \
121 "for prefix in ${boot_prefixes}; do " \
122 "run scan_dev_for_scripts; " \
123 "done;" \
124 "\0" \
125 "boot_a_script=" \
126 "load ${devtype} ${devnum}:${distro_bootpart} " \
127 "${scriptaddr} ${prefix}${script}; " \
128 "env exists secureboot && load ${devtype} " \
129 "${devnum}:${distro_bootpart} " \
130 "${scripthdraddr} ${prefix}${boot_script_hdr} " \
131 "&& esbc_validate ${scripthdraddr};" \
132 "source ${scriptaddr}\0" \
133 "xspi_bootcmd=echo Trying load from FlexSPI flash ...;" \
134 "sf probe 0:0 && sf read $load_addr " \
135 "$kernel_start $kernel_size ; env exists secureboot &&" \
136 "sf read $kernelheader_addr_r $kernelheader_start " \
137 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
138 " bootm $load_addr#$board\0" \
139 "xspi_hdploadcmd=echo Trying load HDP firmware from FlexSPI...;" \
140 "sf probe 0:0 && sf read $load_addr 0x940000 0x30000 " \
141 "&& hdp load $load_addr 0x2000\0" \
142 "sd_bootcmd=echo Trying load from SD ...;" \
143 "mmc dev 0;mmcinfo; mmc read $load_addr " \
144 "$kernel_addr_sd $kernel_size_sd && " \
145 "env exists secureboot && mmc read $kernelheader_addr_r " \
146 "$kernelhdr_addr_sd $kernelhdr_size_sd " \
147 " && esbc_validate ${kernelheader_addr_r};" \
148 "bootm $load_addr#$board\0" \
149 "sd_hdploadcmd=echo Trying load HDP firmware from SD..;" \
150 "mmc dev 0;mmcinfo;mmc read $load_addr 0x4a00 0x200 " \
151 "&& hdp load $load_addr 0x2000\0" \
152 "emmc_bootcmd=echo Trying load from EMMC ..;" \
153 "mmc dev 1;mmcinfo; mmc read $load_addr " \
154 "$kernel_addr_sd $kernel_size_sd && " \
155 "env exists secureboot && mmc read $kernelheader_addr_r " \
156 "$kernelhdr_addr_sd $kernelhdr_size_sd " \
157 " && esbc_validate ${kernelheader_addr_r};" \
158 "bootm $load_addr#$board\0" \
159 "emmc_hdploadcmd=echo Trying load HDP firmware from EMMC..;" \
160 "mmc dev 1;mmcinfo;mmc read $load_addr 0x4a00 0x200 " \
161 "&& hdp load $load_addr 0x2000\0"
162#endif
Yuantian Tang353f36d2019-04-10 16:43:34 +0800163#endif /* __LS1028A_RDB_H */