board/udoo/udoo.c

// SPDX-License-Identifier: GPL-2.0+
/*
 * Copyright (C) 2013 Freescale Semiconductor, Inc.
 *
 * Author: Fabio Estevam <fabio.estevam@freescale.com>
 */

#include <init.h>
#include <net.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <env.h>
#include <malloc.h>
#include <asm/arch/mx6-pins.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/sata.h>
#include <mmc.h>
#include <fsl_esdhc_imx.h>
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
#include <micrel.h>
#include <miiphy.h>
#include <netdev.h>

DECLARE_GLOBAL_DATA_PTR;

#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)

#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

#define WDT_EN		IMX_GPIO_NR(5, 4)
#define WDT_TRG		IMX_GPIO_NR(3, 19)

int dram_init(void)
{
	gd->ram_size = imx_ddr_size();

	return 0;
}

static iomux_v3_cfg_t const uart2_pads[] = {
	IOMUX_PADS(PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
	IOMUX_PADS(PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};

static iomux_v3_cfg_t const usdhc3_pads[] = {
	IOMUX_PADS(PAD_SD3_CLK__SD3_CLK    | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
	IOMUX_PADS(PAD_SD3_CMD__SD3_CMD    | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
	IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
	IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
	IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
	IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
};

static iomux_v3_cfg_t const wdog_pads[] = {
	IOMUX_PADS(PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL)),
	IOMUX_PADS(PAD_EIM_D19__GPIO3_IO19),
};

int mx6_rgmii_rework(struct phy_device *phydev)
{
	/*
	 * Bug: Apparently uDoo does not works with Gigabit switches...
	 * Limiting speed to 10/100Mbps, and setting master mode, seems to
	 * be the only way to have a successfull PHY auto negotiation.
	 * How to fix: Understand why Linux kernel do not have this issue.
	 */
	phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000, 0x1c00);

	/* control data pad skew - devaddr = 0x02, register = 0x04 */
	ksz9031_phy_extended_write(phydev, 0x02,
				   MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
	/* rx data pad skew - devaddr = 0x02, register = 0x05 */
	ksz9031_phy_extended_write(phydev, 0x02,
				   MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
	/* tx data pad skew - devaddr = 0x02, register = 0x05 */
	ksz9031_phy_extended_write(phydev, 0x02,
				   MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
	/* gtx and rx clock pad skew - devaddr = 0x02, register = 0x08 */
	ksz9031_phy_extended_write(phydev, 0x02,
				   MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x03FF);
	return 0;
}

static iomux_v3_cfg_t const enet_pads1[] = {
	IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	/* RGMII reset */
	IOMUX_PADS(PAD_EIM_D23__GPIO3_IO23		| MUX_PAD_CTRL(NO_PAD_CTRL)),
	/* Ethernet power supply */
	IOMUX_PADS(PAD_EIM_EB3__GPIO2_IO31		| MUX_PAD_CTRL(NO_PAD_CTRL)),
	/* pin 32 - 1 - (MODE0) all */
	IOMUX_PADS(PAD_RGMII_RD0__GPIO6_IO25		| MUX_PAD_CTRL(NO_PAD_CTRL)),
	/* pin 31 - 1 - (MODE1) all */
	IOMUX_PADS(PAD_RGMII_RD1__GPIO6_IO27		| MUX_PAD_CTRL(NO_PAD_CTRL)),
	/* pin 28 - 1 - (MODE2) all */
	IOMUX_PADS(PAD_RGMII_RD2__GPIO6_IO28		| MUX_PAD_CTRL(NO_PAD_CTRL)),
	/* pin 27 - 1 - (MODE3) all */
	IOMUX_PADS(PAD_RGMII_RD3__GPIO6_IO29		| MUX_PAD_CTRL(NO_PAD_CTRL)),
	/* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */
	IOMUX_PADS(PAD_RGMII_RX_CTL__GPIO6_IO24	| MUX_PAD_CTRL(NO_PAD_CTRL)),
};

static iomux_v3_cfg_t const enet_pads2[] = {
	IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
	IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
};

static void setup_iomux_enet(void)
{
	SETUP_IOMUX_PADS(enet_pads1);
	udelay(20);
	gpio_direction_output(IMX_GPIO_NR(2, 31), 1); /* Power supply on */

	gpio_direction_output(IMX_GPIO_NR(3, 23), 0); /* assert PHY rst */

	gpio_direction_output(IMX_GPIO_NR(6, 24), 1);
	gpio_direction_output(IMX_GPIO_NR(6, 25), 1);
	gpio_direction_output(IMX_GPIO_NR(6, 27), 1);
	gpio_direction_output(IMX_GPIO_NR(6, 28), 1);
	gpio_direction_output(IMX_GPIO_NR(6, 29), 1);
	udelay(1000);

	gpio_set_value(IMX_GPIO_NR(3, 23), 1); /* deassert PHY rst */

	/* Need 100ms delay to exit from reset. */
	udelay(1000 * 100);

	gpio_free(IMX_GPIO_NR(6, 24));
	gpio_free(IMX_GPIO_NR(6, 25));
	gpio_free(IMX_GPIO_NR(6, 27));
	gpio_free(IMX_GPIO_NR(6, 28));
	gpio_free(IMX_GPIO_NR(6, 29));

	SETUP_IOMUX_PADS(enet_pads2);
}

static void setup_iomux_uart(void)
{
	SETUP_IOMUX_PADS(uart2_pads);
}

static void setup_iomux_wdog(void)
{
	SETUP_IOMUX_PADS(wdog_pads);
	gpio_direction_output(WDT_TRG, 0);
	gpio_direction_output(WDT_EN, 1);
	gpio_direction_input(WDT_TRG);
}

static struct fsl_esdhc_cfg usdhc_cfg = { USDHC3_BASE_ADDR };

int board_mmc_getcd(struct mmc *mmc)
{
	return 1; /* Always present */
}

int board_eth_init(struct bd_info *bis)
{
	uint32_t base = IMX_FEC_BASE;
	struct mii_dev *bus = NULL;
	struct phy_device *phydev = NULL;
	int ret;

	setup_iomux_enet();

#ifdef CONFIG_FEC_MXC
	bus = fec_get_miibus(base, -1);
	if (!bus)
		return -EINVAL;
	/* scan phy 4,5,6,7 */
	phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII);

	if (!phydev) {
		ret = -EINVAL;
		goto free_bus;
	}
	printf("using phy at %d\n", phydev->addr);
	ret  = fec_probe(bis, -1, base, bus, phydev);
	if (ret)
		goto free_phydev;
#endif
	return 0;

free_phydev:
	free(phydev);
free_bus:
	free(bus);
	return ret;
}

int board_mmc_init(struct bd_info *bis)
{
	SETUP_IOMUX_PADS(usdhc3_pads);
	usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
	usdhc_cfg.max_bus_width = 4;

	return fsl_esdhc_initialize(bis, &usdhc_cfg);
}

int board_early_init_f(void)
{
	setup_iomux_wdog();
	setup_iomux_uart();

	return 0;
}

int board_phy_config(struct phy_device *phydev)
{
	mx6_rgmii_rework(phydev);
	if (phydev->drv->config)
		phydev->drv->config(phydev);

	return 0;
}

int board_init(void)
{
	/* address of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

#ifdef CONFIG_SATA
	setup_sata();
#endif
	return 0;
}

int board_late_init(void)
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
	if (is_cpu_type(MXC_CPU_MX6Q))
		env_set("board_rev", "MX6Q");
	else
		env_set("board_rev", "MX6DL");
#endif
	return 0;
}

int checkboard(void)
{
	if (is_cpu_type(MXC_CPU_MX6Q))
		puts("Board: Udoo Quad\n");
	else
		puts("Board: Udoo DualLite\n");

	return 0;
}