blob: ed1334d98593e9eed17bfb0f6eca43964c3a1898 [file] [log] [blame]
Shengzhou Liuc4d0e812013-11-22 17:39:11 +08001/*
2 * Copyright 2013 Freescale Semiconductor, Inc.
3 *
4 * This program is free software; you can redistribute it and/or
5 * modify it under the terms of the GNU General Public License
6 * Version 2 or later as published by the Free Software Foundation.
7 */
8
9#include <common.h>
10#include <i2c.h>
11#include <hwconfig.h>
12#include <asm/mmu.h>
13#include <fsl_ddr_sdram.h>
14#include <fsl_ddr_dimm_params.h>
15#include <asm/fsl_law.h>
16#include "ddr.h"
17
18DECLARE_GLOBAL_DATA_PTR;
19
20void fsl_ddr_board_options(memctl_options_t *popts,
21 dimm_params_t *pdimm,
22 unsigned int ctrl_num)
23{
24 const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
25 ulong ddr_freq;
26
Shengzhou Liu3fdc8272014-01-13 13:01:06 +080027 if (ctrl_num > 1) {
Shengzhou Liuc4d0e812013-11-22 17:39:11 +080028 printf("Not supported controller number %d\n", ctrl_num);
29 return;
30 }
31 if (!pdimm->n_ranks)
32 return;
33
34 /*
35 * we use identical timing for all slots. If needed, change the code
36 * to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
37 */
38 if (popts->registered_dimm_en)
39 pbsp = rdimms[0];
40 else
41 pbsp = udimms[0];
42
Shengzhou Liu3fdc8272014-01-13 13:01:06 +080043 /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
Shengzhou Liuc4d0e812013-11-22 17:39:11 +080044 * freqency and n_banks specified in board_specific_parameters table.
45 */
46 ddr_freq = get_ddr_freq(0) / 1000000;
47 while (pbsp->datarate_mhz_high) {
48 if (pbsp->n_ranks == pdimm->n_ranks &&
49 (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
50 if (ddr_freq <= pbsp->datarate_mhz_high) {
Shengzhou Liuc4d0e812013-11-22 17:39:11 +080051 popts->clk_adjust = pbsp->clk_adjust;
52 popts->wrlvl_start = pbsp->wrlvl_start;
53 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
54 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
Shengzhou Liuc4d0e812013-11-22 17:39:11 +080055 goto found;
56 }
57 pbsp_highest = pbsp;
58 }
59 pbsp++;
60 }
61
62 if (pbsp_highest) {
63 printf("Error: board specific timing not found");
64 printf("for data rate %lu MT/s\n", ddr_freq);
65 printf("Trying to use the highest speed (%u) parameters\n",
66 pbsp_highest->datarate_mhz_high);
Shengzhou Liuc4d0e812013-11-22 17:39:11 +080067 popts->clk_adjust = pbsp_highest->clk_adjust;
68 popts->wrlvl_start = pbsp_highest->wrlvl_start;
69 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
70 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
Shengzhou Liuc4d0e812013-11-22 17:39:11 +080071 } else {
72 panic("DIMM is not supported by this board");
73 }
74found:
75 debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
76 "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, "
77 "wrlvl_ctrl_3 0x%x\n",
78 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
79 pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
80 pbsp->wrlvl_ctl_3);
81
82 /*
83 * Factors to consider for half-strength driver enable:
84 * - number of DIMMs installed
85 */
86 popts->half_strength_driver_enable = 0;
87 /*
88 * Write leveling override
89 */
90 popts->wrlvl_override = 1;
91 popts->wrlvl_sample = 0xf;
92
93 /*
94 * Rtt and Rtt_WR override
95 */
96 popts->rtt_override = 0;
97
98 /* Enable ZQ calibration */
99 popts->zq_en = 1;
100
101 /* DHC_EN =1, ODT = 75 Ohm */
102 popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
103 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
104}
105
106phys_size_t initdram(int board_type)
107{
108 phys_size_t dram_size;
109
110 puts("Initializing....using SPD\n");
111
112 dram_size = fsl_ddr_sdram();
113
114 dram_size = setup_ddr_tlbs(dram_size / 0x100000);
115 dram_size *= 0x100000;
116
117 puts(" DDR: ");
118 return dram_size;
119}