blob: f79bb9dcdd5f76235b4697aa9ce13f429c9af84c [file] [log] [blame]
Enric Balletbò i Serra9d1b2982015-09-07 07:43:20 +02001/*
2 * board.c
3 *
4 * Board functions for TCL SL50 board
5 *
6 * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
7 *
8 * SPDX-License-Identifier: GPL-2.0+
9 */
10
11#include <common.h>
12#include <errno.h>
13#include <spl.h>
14#include <asm/arch/cpu.h>
15#include <asm/arch/hardware.h>
16#include <asm/arch/omap.h>
17#include <asm/arch/ddr_defs.h>
18#include <asm/arch/clock.h>
19#include <asm/arch/gpio.h>
20#include <asm/arch/mmc_host_def.h>
21#include <asm/arch/sys_proto.h>
22#include <asm/arch/mem.h>
23#include <asm/io.h>
24#include <asm/emif.h>
25#include <asm/gpio.h>
26#include <i2c.h>
27#include <miiphy.h>
28#include <cpsw.h>
29#include <power/tps65217.h>
30#include <power/tps65910.h>
31#include <environment.h>
32#include <watchdog.h>
33#include <environment.h>
34#include "board.h"
35
36DECLARE_GLOBAL_DATA_PTR;
37
38static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
39
40#ifndef CONFIG_SKIP_LOWLEVEL_INIT
41
42static const struct ddr_data ddr3_sl50_data = {
43 .datardsratio0 = MT41K256M16HA125E_RD_DQS,
44 .datawdsratio0 = MT41K256M16HA125E_WR_DQS,
45 .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
46 .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
47};
48
49static const struct cmd_control ddr3_sl50_cmd_ctrl_data = {
50 .cmd0csratio = MT41K256M16HA125E_RATIO,
51 .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
52
53 .cmd1csratio = MT41K256M16HA125E_RATIO,
54 .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
55
56 .cmd2csratio = MT41K256M16HA125E_RATIO,
57 .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
58};
59
60static struct emif_regs ddr3_sl50_emif_reg_data = {
61 .sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
62 .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
63 .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
64 .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
65 .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
66 .zq_config = MT41K256M16HA125E_ZQ_CFG,
67 .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
68};
69
70#ifdef CONFIG_SPL_OS_BOOT
71int spl_start_uboot(void)
72{
73 /* break into full u-boot on 'c' */
74 if (serial_tstc() && serial_getc() == 'c')
75 return 1;
76
77#ifdef CONFIG_SPL_ENV_SUPPORT
78 env_init();
Simon Glass310fb142017-08-03 12:22:07 -060079 env_load();
Simon Glassbfebc8c2017-08-03 12:22:13 -060080 if (env_get_yesno("boot_os") != 1)
Enric Balletbò i Serra9d1b2982015-09-07 07:43:20 +020081 return 1;
82#endif
83
84 return 0;
85}
86#endif
87
88#define OSC (V_OSCK/1000000)
89const struct dpll_params dpll_ddr_sl50 = {
90 400, OSC-1, 1, -1, -1, -1, -1};
91
92void am33xx_spl_board_init(void)
93{
94 int mpu_vdd;
95
96 /* Get the frequency */
97 dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
98
99 /* BeagleBone PMIC Code */
100 int usb_cur_lim;
101
102 if (i2c_probe(TPS65217_CHIP_PM))
103 return;
104
105 /*
106 * Increase USB current limit to 1300mA or 1800mA and set
107 * the MPU voltage controller as needed.
108 */
109 if (dpll_mpu_opp100.m == MPUPLL_M_1000) {
110 usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA;
111 mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV;
112 } else {
113 usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
114 mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV;
115 }
116
117 if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
118 TPS65217_POWER_PATH,
119 usb_cur_lim,
120 TPS65217_USB_INPUT_CUR_LIMIT_MASK))
121 puts("tps65217_reg_write failure\n");
122
123 /* Set DCDC3 (CORE) voltage to 1.125V */
124 if (tps65217_voltage_update(TPS65217_DEFDCDC3,
125 TPS65217_DCDC_VOLT_SEL_1125MV)) {
126 puts("tps65217_voltage_update failure\n");
127 return;
128 }
129
130 /* Set CORE Frequencies to OPP100 */
131 do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
132
133 /* Set DCDC2 (MPU) voltage */
134 if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) {
135 puts("tps65217_voltage_update failure\n");
136 return;
137 }
138
139 /*
140 * Set LDO3 to 1.8V and LDO4 to 3.3V
141 */
142 if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
143 TPS65217_DEFLS1,
144 TPS65217_LDO_VOLTAGE_OUT_1_8,
145 TPS65217_LDO_MASK))
146 puts("tps65217_reg_write failure\n");
147
148 if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
149 TPS65217_DEFLS2,
150 TPS65217_LDO_VOLTAGE_OUT_3_3,
151 TPS65217_LDO_MASK))
152 puts("tps65217_reg_write failure\n");
153
154 /* Set MPU Frequency to what we detected now that voltages are set */
155 do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
156}
157
158const struct dpll_params *get_dpll_ddr_params(void)
159{
160 enable_i2c0_pin_mux();
161 i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
162
163 return &dpll_ddr_sl50;
164}
165
166void set_uart_mux_conf(void)
167{
168#if CONFIG_CONS_INDEX == 1
169 enable_uart0_pin_mux();
170#elif CONFIG_CONS_INDEX == 2
171 enable_uart1_pin_mux();
172#elif CONFIG_CONS_INDEX == 3
173 enable_uart2_pin_mux();
174#elif CONFIG_CONS_INDEX == 4
175 enable_uart3_pin_mux();
176#elif CONFIG_CONS_INDEX == 5
177 enable_uart4_pin_mux();
178#elif CONFIG_CONS_INDEX == 6
179 enable_uart5_pin_mux();
180#endif
181}
182
183void set_mux_conf_regs(void)
184{
185 enable_board_pin_mux();
186}
187
188const struct ctrl_ioregs ioregs_evmsk = {
189 .cm0ioctl = MT41J128MJT125_IOCTRL_VALUE,
190 .cm1ioctl = MT41J128MJT125_IOCTRL_VALUE,
191 .cm2ioctl = MT41J128MJT125_IOCTRL_VALUE,
192 .dt0ioctl = MT41J128MJT125_IOCTRL_VALUE,
193 .dt1ioctl = MT41J128MJT125_IOCTRL_VALUE,
194};
195
196const struct ctrl_ioregs ioregs_bonelt = {
197 .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
198 .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
199 .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
200 .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
201 .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
202};
203
204const struct ctrl_ioregs ioregs_evm15 = {
205 .cm0ioctl = MT41J512M8RH125_IOCTRL_VALUE,
206 .cm1ioctl = MT41J512M8RH125_IOCTRL_VALUE,
207 .cm2ioctl = MT41J512M8RH125_IOCTRL_VALUE,
208 .dt0ioctl = MT41J512M8RH125_IOCTRL_VALUE,
209 .dt1ioctl = MT41J512M8RH125_IOCTRL_VALUE,
210};
211
212const struct ctrl_ioregs ioregs = {
213 .cm0ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
214 .cm1ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
215 .cm2ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
216 .dt0ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
217 .dt1ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
218};
219
220void sdram_init(void)
221{
222 config_ddr(400, &ioregs_bonelt,
223 &ddr3_sl50_data,
224 &ddr3_sl50_cmd_ctrl_data,
225 &ddr3_sl50_emif_reg_data, 0);
226}
227#endif
228
229/*
230 * Basic board specific setup. Pinmux has been handled already.
231 */
232int board_init(void)
233{
234#if defined(CONFIG_HW_WATCHDOG)
235 hw_watchdog_init();
236#endif
237
238 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
239 return 0;
240}
241
242#ifdef CONFIG_BOARD_LATE_INIT
243int board_late_init(void)
244{
245 return 0;
246}
247#endif
248
249#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
250 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
251static void cpsw_control(int enabled)
252{
253 /* VTP can be added here */
254
255 return;
256}
257
258static struct cpsw_slave_data cpsw_slaves[] = {
259 {
260 .slave_reg_ofs = 0x208,
261 .sliver_reg_ofs = 0xd80,
262 .phy_addr = 0,
263 },
264 {
265 .slave_reg_ofs = 0x308,
266 .sliver_reg_ofs = 0xdc0,
267 .phy_addr = 1,
268 },
269};
270
271static struct cpsw_platform_data cpsw_data = {
272 .mdio_base = CPSW_MDIO_BASE,
273 .cpsw_base = CPSW_BASE,
274 .mdio_div = 0xff,
275 .channels = 8,
276 .cpdma_reg_ofs = 0x800,
277 .slaves = 1,
278 .slave_data = cpsw_slaves,
279 .ale_reg_ofs = 0xd00,
280 .ale_entries = 1024,
281 .host_port_reg_ofs = 0x108,
282 .hw_stats_reg_ofs = 0x900,
283 .bd_ram_ofs = 0x2000,
284 .mac_control = (1 << 5),
285 .control = cpsw_control,
286 .host_port_num = 0,
287 .version = CPSW_CTRL_VERSION_2,
288};
289#endif
290
291/*
292 * This function will:
293 * Read the eFuse for MAC addresses, and set ethaddr/eth1addr/usbnet_devaddr
294 * in the environment
295 * Perform fixups to the PHY present on certain boards. We only need this
296 * function in:
297 * - SPL with either CPSW or USB ethernet support
298 * - Full U-Boot, with either CPSW or USB ethernet
299 * Build in only these cases to avoid warnings about unused variables
300 * when we build an SPL that has neither option but full U-Boot will.
301 */
302#if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) \
303 && defined(CONFIG_SPL_BUILD)) || \
304 ((defined(CONFIG_DRIVER_TI_CPSW) || \
305 defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)) && \
306 !defined(CONFIG_SPL_BUILD))
307int board_eth_init(bd_t *bis)
308{
309 int rv, n = 0;
310 uint8_t mac_addr[6];
311 uint32_t mac_hi, mac_lo;
312
313 /* try reading mac address from efuse */
314 mac_lo = readl(&cdev->macid0l);
315 mac_hi = readl(&cdev->macid0h);
316 mac_addr[0] = mac_hi & 0xFF;
317 mac_addr[1] = (mac_hi & 0xFF00) >> 8;
318 mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
319 mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
320 mac_addr[4] = mac_lo & 0xFF;
321 mac_addr[5] = (mac_lo & 0xFF00) >> 8;
322
323#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
324 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
Simon Glass00caae62017-08-03 12:22:12 -0600325 if (!env_get("ethaddr")) {
Enric Balletbò i Serra9d1b2982015-09-07 07:43:20 +0200326 printf("<ethaddr> not set. Validating first E-fuse MAC\n");
327
328 if (is_valid_ethaddr(mac_addr))
Simon Glassfd1e9592017-08-03 12:22:11 -0600329 eth_env_set_enetaddr("ethaddr", mac_addr);
Enric Balletbò i Serra9d1b2982015-09-07 07:43:20 +0200330 }
331
332#ifdef CONFIG_DRIVER_TI_CPSW
333
334 mac_lo = readl(&cdev->macid1l);
335 mac_hi = readl(&cdev->macid1h);
336 mac_addr[0] = mac_hi & 0xFF;
337 mac_addr[1] = (mac_hi & 0xFF00) >> 8;
338 mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
339 mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
340 mac_addr[4] = mac_lo & 0xFF;
341 mac_addr[5] = (mac_lo & 0xFF00) >> 8;
342
Simon Glass00caae62017-08-03 12:22:12 -0600343 if (!env_get("eth1addr")) {
Enric Balletbò i Serra9d1b2982015-09-07 07:43:20 +0200344 if (is_valid_ethaddr(mac_addr))
Simon Glassfd1e9592017-08-03 12:22:11 -0600345 eth_env_set_enetaddr("eth1addr", mac_addr);
Enric Balletbò i Serra9d1b2982015-09-07 07:43:20 +0200346 }
347
348
349 writel(MII_MODE_ENABLE, &cdev->miisel);
350 cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
351 PHY_INTERFACE_MODE_MII;
352
353 rv = cpsw_register(&cpsw_data);
354 if (rv < 0)
355 printf("Error %d registering CPSW switch\n", rv);
356 else
357 n += rv;
358#endif
359
360 /*
361 *
362 * CPSW RGMII Internal Delay Mode is not supported in all PVT
363 * operating points. So we must set the TX clock delay feature
364 * in the AR8051 PHY. Since we only support a single ethernet
365 * device in U-Boot, we only do this for the first instance.
366 */
367#define AR8051_PHY_DEBUG_ADDR_REG 0x1d
368#define AR8051_PHY_DEBUG_DATA_REG 0x1e
369#define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5
370#define AR8051_RGMII_TX_CLK_DLY 0x100
371
372#endif
373#if defined(CONFIG_USB_ETHER) && \
374 (!defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_USBETH_SUPPORT))
375 if (is_valid_ether_addr(mac_addr))
Simon Glassfd1e9592017-08-03 12:22:11 -0600376 eth_env_set_enetaddr("usbnet_devaddr", mac_addr);
Enric Balletbò i Serra9d1b2982015-09-07 07:43:20 +0200377
378 rv = usb_eth_initialize(bis);
379 if (rv < 0)
380 printf("Error %d registering USB_ETHER\n", rv);
381 else
382 n += rv;
383#endif
384 return n;
385}
386#endif