blob: c6fb0749921fed221cc0b06c1e7c7a5c93f92f12 [file] [log] [blame]
wdenk0f8c9762002-08-19 11:57:05 +00001/*
2 * (C) Copyright 2001
3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
4 *
5 * See file CREDITS for list of people who contributed to this
6 * project.
7 *
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License as
10 * published by the Free Software Foundation; either version 2 of
11 * the License, or (at your option) any later version.
12 *
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
21 * MA 02111-1307 USA
22 */
23
24/*
25 * board/config.h - configuration options, board specific
26 */
27
28#ifndef __CONFIG_H
29#define __CONFIG_H
30
31/*
32 * High Level Configuration Options
33 * (easy to change)
34 */
35
36#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */
37#define CONFIG_TQM8260 200 /* ...on a TQM8260 module Rev.200 */
38#define CONFIG_SCM 1 /* ...on a System Controller Module */
Jon Loeliger9c4c5ae2005-07-23 10:37:35 -050039#define CONFIG_CPM2 1 /* Has a CPM2 */
wdenk0f8c9762002-08-19 11:57:05 +000040
41#if (CONFIG_TQM8260 <= 100)
42# error "TQM8260 module revison not supported"
43#endif
44
45/* We use a TQM8260 module with a 300MHz CPU */
46#define CONFIG_300MHz
47
48/* Define 60x busmode only if your TQM8260 has L2 cache! */
49#ifdef CONFIG_L2_CACHE
50# define CONFIG_BUSMODE_60x 1 /* bus mode: 60x */
51#else
52# undef CONFIG_BUSMODE_60x /* bus mode: 8260 */
53#endif
54
55/* The board with 300MHz CPU doesn't have L2 cache, but works in 60x bus mode */
56#ifdef CONFIG_300MHz
57# define CONFIG_BUSMODE_60x
58#endif
59
60#define CONFIG_82xx_CONS_SMC1 1 /* console on SMC1 */
61
62#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
63
64#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
65
Wolfgang Denk32bf3d12008-03-03 12:16:44 +010066#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
wdenk0f8c9762002-08-19 11:57:05 +000067
68#undef CONFIG_BOOTARGS
69#define CONFIG_BOOTCOMMAND \
Wolfgang Denk53677ef2008-05-20 16:00:29 +020070 "bootp; " \
71 "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
72 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
wdenk0f8c9762002-08-19 11:57:05 +000073 "bootm"
74
75/* enable I2C and select the hardware/software driver */
76#undef CONFIG_HARD_I2C /* I2C with hardware support */
77#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020078#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
79#define CONFIG_SYS_I2C_SLAVE 0x7F
wdenk0f8c9762002-08-19 11:57:05 +000080
81/*
82 * Software (bit-bang) I2C driver configuration
83 */
84
85#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
86#define I2C_ACTIVE (iop->pdir |= 0x00010000)
87#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
88#define I2C_READ ((iop->pdat & 0x00010000) != 0)
89#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
90 else iop->pdat &= ~0x00010000
91#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
92 else iop->pdat &= ~0x00020000
93#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
94
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020095#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
96#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
97#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
98#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
wdenk0f8c9762002-08-19 11:57:05 +000099
100#define CONFIG_I2C_X
101
102/*
103 * select serial console configuration
104 *
105 * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
106 * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
107 * for SCC).
108 *
109 * if CONFIG_CONS_NONE is defined, then the serial console routines must
110 * defined elsewhere (for example, on the cogent platform, there are serial
111 * ports on the motherboard which are used for the serial console - see
112 * cogent/cma101/serial.[ch]).
113 */
114#define CONFIG_CONS_ON_SMC /* define if console on SMC */
115#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
116#undef CONFIG_CONS_NONE /* define if console on something else*/
117#ifdef CONFIG_82xx_CONS_SMC1
118#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
119#endif
120#ifdef CONFIG_82xx_CONS_SMC2
121#define CONFIG_CONS_INDEX 2 /* which serial channel for console */
122#endif
123
124#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */
125#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */
126#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9 */
127
128/*
129 * select ethernet configuration
130 *
131 * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
132 * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
133 * for FCC)
134 *
135 * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
Jon Loeliger639221c2007-07-09 17:15:49 -0500136 * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
wdenk0f8c9762002-08-19 11:57:05 +0000137 *
138 * (On TQM8260 either SCC1 or FCC2 may be chosen: SCC1 is hardwired to the
139 * X.29 connector, and FCC2 is hardwired to the X.1 connector)
140 */
141#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
142#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
143#undef CONFIG_ETHER_NONE /* define if ether on something else */
144#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */
145
146#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1)
147
148/*
149 * - Rx-CLK is CLK12
150 * - Tx-CLK is CLK11
151 * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
152 * - Enable Full Duplex in FSMR
153 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200154# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
155# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF1CS_CLK12|CMXFCR_TF1CS_CLK11)
156# define CONFIG_SYS_CPMFCR_RAMTYPE 0
157# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
wdenk0f8c9762002-08-19 11:57:05 +0000158
159#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3)
160
161/*
162 * - Rx-CLK is CLK15
163 * - Tx-CLK is CLK16
164 * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
165 * - Enable Full Duplex in FSMR
166 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200167# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
168# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
169# define CONFIG_SYS_CPMFCR_RAMTYPE 0
170# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
wdenk0f8c9762002-08-19 11:57:05 +0000171
172#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
173
174
175/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
176#ifndef CONFIG_300MHz
177#define CONFIG_8260_CLKIN 66666666 /* in Hz */
178#else
179#define CONFIG_8260_CLKIN 83333000 /* in Hz */
180#endif
181
182#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
183#define CONFIG_BAUDRATE 230400
184#else
185#define CONFIG_BAUDRATE 115200
186#endif
187
188#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200189#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
wdenk0f8c9762002-08-19 11:57:05 +0000190
191#undef CONFIG_WATCHDOG /* watchdog disabled */
192
Jon Loeliger18225e82007-07-09 21:31:24 -0500193/*
194 * BOOTP options
195 */
196#define CONFIG_BOOTP_SUBNETMASK
197#define CONFIG_BOOTP_GATEWAY
198#define CONFIG_BOOTP_HOSTNAME
199#define CONFIG_BOOTP_BOOTPATH
200#define CONFIG_BOOTP_BOOTFILESIZE
wdenk0f8c9762002-08-19 11:57:05 +0000201
wdenk0f8c9762002-08-19 11:57:05 +0000202
Jon Loeligerfe7f7822007-07-08 15:02:44 -0500203/*
204 * Command line configuration.
205 */
206#include <config_cmd_default.h>
207
208#define CONFIG_CMD_DHCP
209#define CONFIG_CMD_I2C
210#define CONFIG_CMD_EEPROM
211#define CONFIG_CMD_BSP
212
wdenk0f8c9762002-08-19 11:57:05 +0000213
214/*
215 * Miscellaneous configurable options
216 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200217#define CONFIG_SYS_LONGHELP /* undef to save memory */
218#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
Jon Loeligerfe7f7822007-07-08 15:02:44 -0500219#if defined(CONFIG_CMD_KGDB)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200220#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
wdenk0f8c9762002-08-19 11:57:05 +0000221#else
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200222#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
wdenk0f8c9762002-08-19 11:57:05 +0000223#endif
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200224#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
225#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
226#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
wdenk0f8c9762002-08-19 11:57:05 +0000227
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200228#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
229#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
wdenk0f8c9762002-08-19 11:57:05 +0000230
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200231#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
wdenk0f8c9762002-08-19 11:57:05 +0000232
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200233#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
wdenk0f8c9762002-08-19 11:57:05 +0000234
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200235#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
wdenk0f8c9762002-08-19 11:57:05 +0000236
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200237#define CONFIG_SYS_RESET_ADDRESS 0xFFFFFFFC /* "bad" address */
wdenk0f8c9762002-08-19 11:57:05 +0000238
239#define CONFIG_MISC_INIT_R /* have misc_init_r() function */
240
241/*
242 * For booting Linux, the board info and command line data
243 * have to be in the first 8 MB of memory, since this is
244 * the maximum mapped by the Linux kernel during initialization.
245 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200246#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
wdenk0f8c9762002-08-19 11:57:05 +0000247
248
249/* What should the base address of the main FLASH be and how big is
250 * it (in MBytes)? This must contain TEXT_BASE from board/tqm8260/config.mk
251 * The main FLASH is whichever is connected to *CS0.
252 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200253#define CONFIG_SYS_FLASH0_BASE 0x40000000
254#define CONFIG_SYS_FLASH1_BASE 0x60000000
255#define CONFIG_SYS_FLASH0_SIZE 32
256#define CONFIG_SYS_FLASH1_SIZE 32
wdenk0f8c9762002-08-19 11:57:05 +0000257
258/* Flash bank size (for preliminary settings)
259 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200260#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
wdenk0f8c9762002-08-19 11:57:05 +0000261
262/*-----------------------------------------------------------------------
263 * FLASH organization
264 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200265#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
266#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
wdenk0f8c9762002-08-19 11:57:05 +0000267
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200268#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
269#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
wdenk0f8c9762002-08-19 11:57:05 +0000270
271#if 0
272/* Start port with environment in flash; switch to EEPROM later */
Jean-Christophe PLAGNIOL-VILLARD5a1aceb2008-09-10 22:48:04 +0200273#define CONFIG_ENV_IS_IN_FLASH 1
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200274#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+0x40000)
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +0200275#define CONFIG_ENV_SIZE 0x40000
276#define CONFIG_ENV_SECT_SIZE 0x40000
wdenk0f8c9762002-08-19 11:57:05 +0000277#else
278/* Final version: environment in EEPROM */
Jean-Christophe PLAGNIOL-VILLARDbb1f8b42008-09-05 09:19:30 +0200279#define CONFIG_ENV_IS_IN_EEPROM 1
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +0200280#define CONFIG_ENV_OFFSET 0
281#define CONFIG_ENV_SIZE 2048
wdenk0f8c9762002-08-19 11:57:05 +0000282#endif
283
284/*-----------------------------------------------------------------------
285 * Hardware Information Block
286 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200287#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
288#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
289#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
wdenk0f8c9762002-08-19 11:57:05 +0000290
291/*-----------------------------------------------------------------------
292 * Hard Reset Configuration Words
293 *
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200294 * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
wdenk0f8c9762002-08-19 11:57:05 +0000295 * defines for the various registers affected by the HRCW e.g. changing
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200296 * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
wdenk0f8c9762002-08-19 11:57:05 +0000297 */
298#if defined(CONFIG_266MHz)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200299#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \
wdenk8bde7f72003-06-27 21:31:46 +0000300 HRCW_MODCK_H0111)
wdenk0f8c9762002-08-19 11:57:05 +0000301#elif defined(CONFIG_300MHz)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200302#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \
wdenk8bde7f72003-06-27 21:31:46 +0000303 HRCW_MODCK_H0110)
wdenk0f8c9762002-08-19 11:57:05 +0000304#else
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200305#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS)
wdenk0f8c9762002-08-19 11:57:05 +0000306#endif
307
308/* no slaves so just fill with zeros */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200309#define CONFIG_SYS_HRCW_SLAVE1 0
310#define CONFIG_SYS_HRCW_SLAVE2 0
311#define CONFIG_SYS_HRCW_SLAVE3 0
312#define CONFIG_SYS_HRCW_SLAVE4 0
313#define CONFIG_SYS_HRCW_SLAVE5 0
314#define CONFIG_SYS_HRCW_SLAVE6 0
315#define CONFIG_SYS_HRCW_SLAVE7 0
wdenk0f8c9762002-08-19 11:57:05 +0000316
317/*-----------------------------------------------------------------------
318 * Internal Memory Mapped Register
319 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200320#define CONFIG_SYS_IMMR 0xFFF00000
wdenk0f8c9762002-08-19 11:57:05 +0000321
322/*-----------------------------------------------------------------------
323 * Definitions for initial stack pointer and data area (in DPRAM)
324 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200325#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
326#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
327#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/
328#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
329#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
wdenk0f8c9762002-08-19 11:57:05 +0000330
331/*-----------------------------------------------------------------------
332 * Start addresses for the final memory configuration
333 * (Set up by the startup code)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200334 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
wdenk0f8c9762002-08-19 11:57:05 +0000335 *
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200336 * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE, local SDRAM
wdenk0f8c9762002-08-19 11:57:05 +0000337 * is mapped at SDRAM_BASE2_PRELIM.
338 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200339#define CONFIG_SYS_SDRAM_BASE 0x00000000
340#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
341#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
342#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
343#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
wdenk0f8c9762002-08-19 11:57:05 +0000344
345/*
346 * Internal Definitions
347 *
348 * Boot Flags
349 */
350#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/
351#define BOOTFLAG_WARM 0x02 /* Software reboot */
352
353
354/*-----------------------------------------------------------------------
355 * Hardware Information Block
356 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200357#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
358#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
359#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
wdenk0f8c9762002-08-19 11:57:05 +0000360
361/*-----------------------------------------------------------------------
362 * Cache Configuration
363 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200364#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
Jon Loeligerfe7f7822007-07-08 15:02:44 -0500365#if defined(CONFIG_CMD_KGDB)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200366# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
wdenk0f8c9762002-08-19 11:57:05 +0000367#endif
368
369/*-----------------------------------------------------------------------
370 * HIDx - Hardware Implementation-dependent Registers 2-11
371 *-----------------------------------------------------------------------
372 * HID0 also contains cache control - initially enable both caches and
373 * invalidate contents, then the final state leaves only the instruction
374 * cache enabled. Note that Power-On and Hard reset invalidate the caches,
375 * but Soft reset does not.
376 *
377 * HID1 has only read-only information - nothing to set.
378 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200379#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
wdenk8bde7f72003-06-27 21:31:46 +0000380 HID0_IFEM|HID0_ABE)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200381#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE)
382#define CONFIG_SYS_HID2 0
wdenk0f8c9762002-08-19 11:57:05 +0000383
384/*-----------------------------------------------------------------------
385 * RMR - Reset Mode Register 5-5
386 *-----------------------------------------------------------------------
387 * turn on Checkstop Reset Enable
388 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200389#define CONFIG_SYS_RMR RMR_CSRE
wdenk0f8c9762002-08-19 11:57:05 +0000390
391/*-----------------------------------------------------------------------
392 * BCR - Bus Configuration 4-25
393 *-----------------------------------------------------------------------
394 */
395#ifdef CONFIG_BUSMODE_60x
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200396#define CONFIG_SYS_BCR (BCR_EBM|BCR_L2C|BCR_LETM|\
wdenk0f8c9762002-08-19 11:57:05 +0000397 BCR_NPQM0|BCR_NPQM1|BCR_NPQM2) /* 60x mode */
398#else
399#define BCR_APD01 0x10000000
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200400#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
wdenk0f8c9762002-08-19 11:57:05 +0000401#endif
402
403/*-----------------------------------------------------------------------
404 * SIUMCR - SIU Module Configuration 4-31
405 *-----------------------------------------------------------------------
406 */
407#if 0
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200408#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10)
wdenk0f8c9762002-08-19 11:57:05 +0000409#else
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200410#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10)
wdenk0f8c9762002-08-19 11:57:05 +0000411#endif
412
413
414/*-----------------------------------------------------------------------
415 * SYPCR - System Protection Control 4-35
416 * SYPCR can only be written once after reset!
417 *-----------------------------------------------------------------------
418 * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
419 */
420#if defined(CONFIG_WATCHDOG)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200421#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
wdenk8bde7f72003-06-27 21:31:46 +0000422 SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
wdenk0f8c9762002-08-19 11:57:05 +0000423#else
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200424#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
wdenk8bde7f72003-06-27 21:31:46 +0000425 SYPCR_SWRI|SYPCR_SWP)
wdenk0f8c9762002-08-19 11:57:05 +0000426#endif /* CONFIG_WATCHDOG */
427
428/*-----------------------------------------------------------------------
429 * TMCNTSC - Time Counter Status and Control 4-40
430 *-----------------------------------------------------------------------
431 * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
432 * and enable Time Counter
433 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200434#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
wdenk0f8c9762002-08-19 11:57:05 +0000435
436/*-----------------------------------------------------------------------
437 * PISCR - Periodic Interrupt Status and Control 4-42
438 *-----------------------------------------------------------------------
439 * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
440 * Periodic timer
441 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200442#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
wdenk0f8c9762002-08-19 11:57:05 +0000443
444/*-----------------------------------------------------------------------
445 * SCCR - System Clock Control 9-8
446 *-----------------------------------------------------------------------
447 * Ensure DFBRG is Divide by 16
448 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200449#define CONFIG_SYS_SCCR 0
wdenk0f8c9762002-08-19 11:57:05 +0000450
451/*-----------------------------------------------------------------------
452 * RCCR - RISC Controller Configuration 13-7
453 *-----------------------------------------------------------------------
454 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200455#define CONFIG_SYS_RCCR 0
wdenk0f8c9762002-08-19 11:57:05 +0000456
457/*
458 * Init Memory Controller:
459 *
460 * Bank Bus Machine PortSz Device
461 * ---- --- ------- ------ ------
462 * 0 60x GPCM 64 bit FLASH
463 * 1 60x SDRAM 64 bit SDRAM
464 * 2 Local SDRAM 32 bit SDRAM
465 *
466 */
467
468 /* Initialize SDRAM on local bus
469 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200470#define CONFIG_SYS_INIT_LOCAL_SDRAM
wdenk0f8c9762002-08-19 11:57:05 +0000471
472#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
473
474/* Minimum mask to separate preliminary
475 * address ranges for CS[0:2]
476 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200477#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (512<<20) /* less than 512 MB */
478#define CONFIG_SYS_LOCAL_SDRAM_LIMIT (128<<20) /* less than 128 MB */
wdenk0f8c9762002-08-19 11:57:05 +0000479
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200480#define CONFIG_SYS_MPTPR 0x4000
wdenk0f8c9762002-08-19 11:57:05 +0000481
482/*-----------------------------------------------------------------------------
483 * Address for Mode Register Set (MRS) command
484 *-----------------------------------------------------------------------------
485 * In fact, the address is rather configuration data presented to the SDRAM on
486 * its address lines. Because the address lines may be mux'ed externally either
487 * for 8 column or 9 column devices, some bits appear twice in the 8260's
488 * address:
489 *
490 * | (RFU) | (RFU) | WBL | TM | CL | BT | Burst Length |
491 * | BA1 BA0 | A12 : A10 | A9 | A8 A7 | A6 : A4 | A3 | A2 : A0 |
492 * 8 columns mux'ing: | A9 | A10 A21 | A22 : A24 | A25 | A26 : A28 |
493 * 9 columns mux'ing: | A8 | A20 A21 | A22 : A24 | A25 | A26 : A28 |
494 * Settings: | 0 | 0 0 | 0 1 0 | 0 | 0 1 0 |
495 *-----------------------------------------------------------------------------
496 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200497#define CONFIG_SYS_MRS_OFFS 0x00000110
wdenk0f8c9762002-08-19 11:57:05 +0000498
499
500/* Bank 0 - FLASH
501 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200502#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
wdenk8bde7f72003-06-27 21:31:46 +0000503 BRx_PS_64 |\
504 BRx_MS_GPCM_P |\
505 BRx_V)
wdenk0f8c9762002-08-19 11:57:05 +0000506
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200507#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
wdenk8bde7f72003-06-27 21:31:46 +0000508 ORxG_CSNT |\
509 ORxG_ACS_DIV1 |\
510 ORxG_SCY_3_CLK |\
511 ORxG_EHTR |\
512 ORxG_TRLX)
wdenk0f8c9762002-08-19 11:57:05 +0000513
514 /* SDRAM on TQM8260 can have either 8 or 9 columns.
515 * The number affects configuration values.
516 */
517
518/* Bank 1 - 60x bus SDRAM
519 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200520#define CONFIG_SYS_PSRT 0x20
521#define CONFIG_SYS_LSRT 0x20
522#ifndef CONFIG_SYS_RAMBOOT
523#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
wdenk8bde7f72003-06-27 21:31:46 +0000524 BRx_PS_64 |\
525 BRx_MS_SDRAM_P |\
526 BRx_V)
wdenk0f8c9762002-08-19 11:57:05 +0000527
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200528#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1_8COL
wdenk0f8c9762002-08-19 11:57:05 +0000529
530
531 /* SDRAM initialization values for 8-column chips
532 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200533#define CONFIG_SYS_OR1_8COL ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
wdenk8bde7f72003-06-27 21:31:46 +0000534 ORxS_BPD_4 |\
535 ORxS_ROWST_PBI1_A7 |\
536 ORxS_NUMR_12)
wdenk0f8c9762002-08-19 11:57:05 +0000537
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200538#define CONFIG_SYS_PSDMR_8COL (PSDMR_PBI |\
wdenk8bde7f72003-06-27 21:31:46 +0000539 PSDMR_SDAM_A15_IS_A5 |\
540 PSDMR_BSMA_A12_A14 |\
541 PSDMR_SDA10_PBI1_A8 |\
542 PSDMR_RFRC_7_CLK |\
543 PSDMR_PRETOACT_2W |\
544 PSDMR_ACTTORW_2W |\
545 PSDMR_LDOTOPRE_1C |\
546 PSDMR_WRC_2C |\
547 PSDMR_EAMUX |\
548 PSDMR_CL_2)
wdenk0f8c9762002-08-19 11:57:05 +0000549
550 /* SDRAM initialization values for 9-column chips
551 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200552#define CONFIG_SYS_OR1_9COL ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
wdenk8bde7f72003-06-27 21:31:46 +0000553 ORxS_BPD_4 |\
554 ORxS_ROWST_PBI1_A5 |\
555 ORxS_NUMR_13)
wdenk0f8c9762002-08-19 11:57:05 +0000556
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200557#define CONFIG_SYS_PSDMR_9COL (PSDMR_PBI |\
wdenk8bde7f72003-06-27 21:31:46 +0000558 PSDMR_SDAM_A16_IS_A5 |\
559 PSDMR_BSMA_A12_A14 |\
560 PSDMR_SDA10_PBI1_A7 |\
561 PSDMR_RFRC_7_CLK |\
562 PSDMR_PRETOACT_2W |\
563 PSDMR_ACTTORW_2W |\
564 PSDMR_LDOTOPRE_1C |\
565 PSDMR_WRC_2C |\
566 PSDMR_EAMUX |\
567 PSDMR_CL_2)
wdenk0f8c9762002-08-19 11:57:05 +0000568
569/* Bank 2 - Local bus SDRAM
570 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200571#ifdef CONFIG_SYS_INIT_LOCAL_SDRAM
572#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BRx_BA_MSK) |\
wdenk8bde7f72003-06-27 21:31:46 +0000573 BRx_PS_32 |\
574 BRx_MS_SDRAM_L |\
575 BRx_V)
wdenk0f8c9762002-08-19 11:57:05 +0000576
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200577#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_8COL
wdenk0f8c9762002-08-19 11:57:05 +0000578
579#define SDRAM_BASE2_PRELIM 0x80000000
580
581 /* SDRAM initialization values for 8-column chips
582 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200583#define CONFIG_SYS_OR2_8COL ((~(CONFIG_SYS_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
wdenk8bde7f72003-06-27 21:31:46 +0000584 ORxS_BPD_4 |\
585 ORxS_ROWST_PBI1_A8 |\
586 ORxS_NUMR_12)
wdenk0f8c9762002-08-19 11:57:05 +0000587
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200588#define CONFIG_SYS_LSDMR_8COL (PSDMR_PBI |\
wdenk8bde7f72003-06-27 21:31:46 +0000589 PSDMR_SDAM_A15_IS_A5 |\
590 PSDMR_BSMA_A13_A15 |\
591 PSDMR_SDA10_PBI1_A9 |\
592 PSDMR_RFRC_7_CLK |\
593 PSDMR_PRETOACT_2W |\
594 PSDMR_ACTTORW_2W |\
595 PSDMR_BL |\
596 PSDMR_LDOTOPRE_1C |\
597 PSDMR_WRC_2C |\
598 PSDMR_CL_2)
wdenk0f8c9762002-08-19 11:57:05 +0000599
600 /* SDRAM initialization values for 9-column chips
601 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200602#define CONFIG_SYS_OR2_9COL ((~(CONFIG_SYS_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
wdenk8bde7f72003-06-27 21:31:46 +0000603 ORxS_BPD_4 |\
604 ORxS_ROWST_PBI1_A6 |\
605 ORxS_NUMR_13)
wdenk0f8c9762002-08-19 11:57:05 +0000606
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200607#define CONFIG_SYS_LSDMR_9COL (PSDMR_PBI |\
wdenk8bde7f72003-06-27 21:31:46 +0000608 PSDMR_SDAM_A16_IS_A5 |\
609 PSDMR_BSMA_A13_A15 |\
610 PSDMR_SDA10_PBI1_A8 |\
611 PSDMR_RFRC_7_CLK |\
612 PSDMR_PRETOACT_2W |\
613 PSDMR_ACTTORW_2W |\
614 PSDMR_BL |\
615 PSDMR_LDOTOPRE_1C |\
616 PSDMR_WRC_2C |\
617 PSDMR_CL_2)
wdenk0f8c9762002-08-19 11:57:05 +0000618
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200619#endif /* CONFIG_SYS_INIT_LOCAL_SDRAM */
wdenk0f8c9762002-08-19 11:57:05 +0000620
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200621#endif /* CONFIG_SYS_RAMBOOT */
wdenk0f8c9762002-08-19 11:57:05 +0000622
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200623#define CONFIG_SYS_CAN0_BASE 0xc0000000
624#define CONFIG_SYS_CAN1_BASE 0xc0008000
625#define CONFIG_SYS_FIOX_BASE 0xc0010000
626#define CONFIG_SYS_FDOHM_BASE 0xc0018000
627#define CONFIG_SYS_EXTPROM_BASE 0xc2000000
wdenk0f8c9762002-08-19 11:57:05 +0000628
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200629#define CONFIG_SYS_CAN_SIZE 0x00000100
630#define CONFIG_SYS_FIOX_SIZE 0x00000020
631#define CONFIG_SYS_FDOHM_SIZE 0x00002000
632#define CONFIG_SYS_EXTPROM_BANK_SIZE 0x01000000
wdenk0f8c9762002-08-19 11:57:05 +0000633
634#define EXT_EEPROM_MAX_FLASH_BANKS 0x02
635
636/* CS3 - CAN 0
637 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200638#define CONFIG_SYS_CAN0_BR3 ((CONFIG_SYS_CAN0_BASE & BRx_BA_MSK) |\
wdenk0f8c9762002-08-19 11:57:05 +0000639 BRx_PS_8 |\
640 BRx_MS_UPMA |\
641 BRx_V)
642
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200643#define CONFIG_SYS_CAN0_OR3 (P2SZ_TO_AM(CONFIG_SYS_CAN_SIZE) |\
wdenk0f8c9762002-08-19 11:57:05 +0000644 ORxU_BI |\
645 ORxU_EHTR_4IDLE)
646
647/* CS4 - CAN 1
648 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200649#define CONFIG_SYS_CAN1_BR4 ((CONFIG_SYS_CAN1_BASE & BRx_BA_MSK) |\
wdenk0f8c9762002-08-19 11:57:05 +0000650 BRx_PS_8 |\
651 BRx_MS_UPMA |\
652 BRx_V)
653
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200654#define CONFIG_SYS_CAN1_OR4 (P2SZ_TO_AM(CONFIG_SYS_CAN_SIZE) |\
wdenk0f8c9762002-08-19 11:57:05 +0000655 ORxU_BI |\
656 ORxU_EHTR_4IDLE)
657
658/* CS5 - Extended PROM (16MB optional)
659 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200660#define CONFIG_SYS_EXTPROM_BR5 ((CONFIG_SYS_EXTPROM_BASE & BRx_BA_MSK)|\
wdenk0f8c9762002-08-19 11:57:05 +0000661 BRx_PS_32 |\
662 BRx_MS_GPCM_P |\
663 BRx_V)
664
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200665#define CONFIG_SYS_EXTPROM_OR5 (P2SZ_TO_AM(CONFIG_SYS_EXTPROM_BANK_SIZE)|\
wdenk0f8c9762002-08-19 11:57:05 +0000666 ORxG_CSNT |\
667 ORxG_ACS_DIV4 |\
668 ORxG_SCY_5_CLK |\
669 ORxG_TRLX)
670
671/* CS6 - Extended PROM (16MB optional)
672 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200673#define CONFIG_SYS_EXTPROM_BR6 (((CONFIG_SYS_EXTPROM_BASE + \
674 CONFIG_SYS_EXTPROM_BANK_SIZE) & BRx_BA_MSK)|\
wdenk0f8c9762002-08-19 11:57:05 +0000675 BRx_PS_32 |\
676 BRx_MS_GPCM_P |\
677 BRx_V)
678
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200679#define CONFIG_SYS_EXTPROM_OR6 (P2SZ_TO_AM(CONFIG_SYS_EXTPROM_BANK_SIZE)|\
wdenk0f8c9762002-08-19 11:57:05 +0000680 ORxG_CSNT |\
681 ORxG_ACS_DIV4 |\
682 ORxG_SCY_5_CLK |\
683 ORxG_TRLX)
684
685/* CS7 - FPGA FIOX: Glue Logic
686 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200687#define CONFIG_SYS_FIOX_BR7 ((CONFIG_SYS_FIOX_BASE & BRx_BA_MSK) |\
wdenk0f8c9762002-08-19 11:57:05 +0000688 BRx_PS_32 |\
689 BRx_MS_GPCM_P |\
690 BRx_V)
691
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200692#define CONFIG_SYS_FIOX_OR7 (P2SZ_TO_AM(CONFIG_SYS_FIOX_SIZE) |\
wdenk0f8c9762002-08-19 11:57:05 +0000693 ORxG_ACS_DIV4 |\
694 ORxG_SCY_5_CLK |\
695 ORxG_TRLX)
696
697/* CS8 - FPGA DOH Master
698 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200699#define CONFIG_SYS_FDOHM_BR8 ((CONFIG_SYS_FDOHM_BASE & BRx_BA_MSK) |\
wdenk0f8c9762002-08-19 11:57:05 +0000700 BRx_PS_16 |\
701 BRx_MS_GPCM_P |\
702 BRx_V)
703
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200704#define CONFIG_SYS_FDOHM_OR8 (P2SZ_TO_AM(CONFIG_SYS_FDOHM_SIZE) |\
wdenk0f8c9762002-08-19 11:57:05 +0000705 ORxG_ACS_DIV4 |\
706 ORxG_SCY_5_CLK |\
707 ORxG_TRLX)
708
709
710/* FPGA configuration */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200711#define CONFIG_SYS_PD_FIOX_PROG (1 << (31- 5)) /* PD 5 */
712#define CONFIG_SYS_PD_FIOX_DONE (1 << (31-28)) /* PD 28 */
713#define CONFIG_SYS_PD_FIOX_INIT (1 << (31-29)) /* PD 29 */
wdenk0f8c9762002-08-19 11:57:05 +0000714
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200715#define CONFIG_SYS_PD_FDOHM_PROG (1 << (31- 4)) /* PD 4 */
716#define CONFIG_SYS_PD_FDOHM_DONE (1 << (31-26)) /* PD 26 */
717#define CONFIG_SYS_PD_FDOHM_INIT (1 << (31-27)) /* PD 27 */
wdenk0f8c9762002-08-19 11:57:05 +0000718
719
720#endif /* __CONFIG_H */