| Chris Brandt | ba932bc | 2017-08-23 14:53:59 -0500 | [diff] [blame] | 1 | // SPDX-License-Identifier: GPL-2.0 |
| 2 | /* |
| 3 | * Device Tree Source for the GR-Peach board |
| 4 | * |
| 5 | * Copyright (C) 2017 Jacopo Mondi <jacopo+renesas@jmondi.org> |
| 6 | * Copyright (C) 2016 Renesas Electronics |
| 7 | */ |
| 8 | |
| 9 | /dts-v1/; |
| 10 | #include "r7s72100.dtsi" |
| 11 | #include <dt-bindings/gpio/gpio.h> |
| 12 | #include <dt-bindings/pinctrl/r7s72100-pinctrl.h> |
| 13 | |
| 14 | / { |
| 15 | model = "GR-Peach"; |
| 16 | compatible = "renesas,gr-peach", "renesas,r7s72100"; |
| 17 | |
| 18 | aliases { |
| 19 | serial0 = &scif2; |
| 20 | }; |
| 21 | |
| 22 | chosen { |
| 23 | bootargs = "ignore_loglevel rw root=/dev/mtdblock0"; |
| 24 | stdout-path = "serial0:115200n8"; |
| 25 | }; |
| 26 | |
| 27 | memory@20000000 { |
| 28 | device_type = "memory"; |
| 29 | reg = <0x20000000 0x00a00000>; |
| 30 | }; |
| 31 | |
| 32 | lbsc { |
| 33 | #address-cells = <1>; |
| 34 | #size-cells = <1>; |
| 35 | }; |
| 36 | |
| 37 | flash@18000000 { |
| 38 | compatible = "mtd-rom"; |
| 39 | probe-type = "map_rom"; |
| 40 | reg = <0x18000000 0x00800000>; |
| 41 | bank-width = <4>; |
| 42 | device-width = <1>; |
| 43 | |
| 44 | #address-cells = <1>; |
| 45 | #size-cells = <1>; |
| 46 | |
| 47 | rootfs@600000 { |
| 48 | label = "rootfs"; |
| 49 | reg = <0x00600000 0x00200000>; |
| 50 | }; |
| 51 | }; |
| 52 | |
| 53 | leds { |
| 54 | status = "okay"; |
| 55 | compatible = "gpio-leds"; |
| 56 | |
| 57 | led1 { |
| 58 | gpios = <&port6 12 GPIO_ACTIVE_HIGH>; |
| 59 | }; |
| 60 | }; |
| 61 | }; |
| 62 | |
| 63 | &pinctrl { |
| 64 | scif2_pins: serial2 { |
| 65 | /* P6_2 as RxD2; P6_3 as TxD2 */ |
| 66 | pinmux = <RZA1_PINMUX(6, 2, 7)>, <RZA1_PINMUX(6, 3, 7)>; |
| 67 | }; |
| 68 | |
| 69 | ether_pins: ether { |
| 70 | /* Ethernet on Ports 1,3,5,10 */ |
| 71 | pinmux = <RZA1_PINMUX(1, 14, 4)>, /* P1_14 = ET_COL */ |
| 72 | <RZA1_PINMUX(3, 0, 2)>, /* P3_0 = ET_TXCLK */ |
| 73 | <RZA1_PINMUX(3, 3, 2)>, /* P3_3 = ET_MDIO */ |
| 74 | <RZA1_PINMUX(3, 4, 2)>, /* P3_4 = ET_RXCLK */ |
| 75 | <RZA1_PINMUX(3, 5, 2)>, /* P3_5 = ET_RXER */ |
| 76 | <RZA1_PINMUX(3, 6, 2)>, /* P3_6 = ET_RXDV */ |
| 77 | <RZA1_PINMUX(5, 9, 2)>, /* P5_9 = ET_MDC */ |
| 78 | <RZA1_PINMUX(10, 1, 4)>, /* P10_1 = ET_TXER */ |
| 79 | <RZA1_PINMUX(10, 2, 4)>, /* P10_2 = ET_TXEN */ |
| 80 | <RZA1_PINMUX(10, 3, 4)>, /* P10_3 = ET_CRS */ |
| 81 | <RZA1_PINMUX(10, 4, 4)>, /* P10_4 = ET_TXD0 */ |
| 82 | <RZA1_PINMUX(10, 5, 4)>, /* P10_5 = ET_TXD1 */ |
| 83 | <RZA1_PINMUX(10, 6, 4)>, /* P10_6 = ET_TXD2 */ |
| 84 | <RZA1_PINMUX(10, 7, 4)>, /* P10_7 = ET_TXD3 */ |
| 85 | <RZA1_PINMUX(10, 8, 4)>, /* P10_8 = ET_RXD0 */ |
| 86 | <RZA1_PINMUX(10, 9, 4)>, /* P10_9 = ET_RXD1 */ |
| 87 | <RZA1_PINMUX(10, 10, 4)>,/* P10_10 = ET_RXD2 */ |
| 88 | <RZA1_PINMUX(10, 11, 4)>;/* P10_11 = ET_RXD3 */ |
| 89 | }; |
| 90 | }; |
| 91 | |
| 92 | &extal_clk { |
| 93 | clock-frequency = <13333000>; |
| 94 | }; |
| 95 | |
| 96 | &usb_x1_clk { |
| 97 | clock-frequency = <48000000>; |
| 98 | }; |
| 99 | |
| 100 | &mtu2 { |
| 101 | status = "okay"; |
| 102 | }; |
| 103 | |
| 104 | &ostm0 { |
| 105 | status = "okay"; |
| 106 | }; |
| 107 | |
| 108 | &ostm1 { |
| 109 | status = "okay"; |
| 110 | }; |
| 111 | |
| 112 | &scif2 { |
| 113 | pinctrl-names = "default"; |
| 114 | pinctrl-0 = <&scif2_pins>; |
| 115 | |
| 116 | status = "okay"; |
| 117 | }; |
| 118 | |
| 119 | ðer { |
| 120 | pinctrl-names = "default"; |
| 121 | pinctrl-0 = <ðer_pins>; |
| 122 | |
| 123 | status = "okay"; |
| 124 | |
| 125 | renesas,no-ether-link; |
| 126 | phy-handle = <&phy0>; |
| 127 | |
| 128 | phy0: ethernet-phy@0 { |
| 129 | reg = <0>; |
| 130 | |
| 131 | reset-gpios = <&port4 2 GPIO_ACTIVE_LOW>; |
| 132 | reset-delay-us = <5>; |
| 133 | }; |
| 134 | }; |