blob: 2afd927463d42afba2613003e96ae8fa1f9f6806 [file] [log] [blame]
Siddarth Gore16b76702010-03-18 20:25:40 +05301#
2# (C) Copyright 2009
3# Marvell Semiconductor <www.marvell.com>
4# Written-by: Siddarth Gore <gores@marvell.com>
5#
6# See file CREDITS for list of people who contributed to this
7# project.
8#
9# This program is free software; you can redistribute it and/or
10# modify it under the terms of the GNU General Public License as
11# published by the Free Software Foundation; either version 2 of
12# the License, or (at your option) any later version.
13#
14# This program is distributed in the hope that it will be useful,
15# but WITHOUT ANY WARRANTY; without even the implied warranty of
16# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
17# GNU General Public License for more details.
18#
19# You should have received a copy of the GNU General Public License
20# along with this program; if not, write to the Free Software
21# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
22# MA 02110-1301 USA
23#
24# Refer docs/README.kwimage for more details about how-to configure
25# and create kirkwood boot image
26#
27
28# Boot Media configurations
29BOOT_FROM nand
30NAND_ECC_MODE default
31NAND_PAGE_SIZE 0x0800
32
33# SOC registers configuration using bootrom header extension
34# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
35
36# Configure RGMII-0/1 interface pad voltage to 1.8V
37DATA 0xFFD100e0 0x1b1b9b9b
38
39#Dram initalization for SINGLE x16 CL=5 @ 400MHz
40DATA 0xFFD01400 0x43000c30 # DDR Configuration register
41# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
42# bit23-14: zero
43# bit24: 1= enable exit self refresh mode on DDR access
44# bit25: 1 required
45# bit29-26: zero
46# bit31-30: 01
47
48DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
49# bit 4: 0=addr/cmd in smame cycle
50# bit 5: 0=clk is driven during self refresh, we don't care for APX
51# bit 6: 0=use recommended falling edge of clk for addr/cmd
52# bit14: 0=input buffer always powered up
53# bit18: 1=cpu lock transaction enabled
54# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
55# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
56# bit30-28: 3 required
57# bit31: 0=no additional STARTBURST delay
58
59DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
60# bit3-0: TRAS lsbs
61# bit7-4: TRCD
62# bit11- 8: TRP
63# bit15-12: TWR
64# bit19-16: TWTR
65# bit20: TRAS msb
66# bit23-21: 0x0
67# bit27-24: TRRD
68# bit31-28: TRTP
69
70DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
71# bit6-0: TRFC
72# bit8-7: TR2R
73# bit10-9: TR2W
74# bit12-11: TW2W
75# bit31-13: zero required
76
77DATA 0xFFD01410 0x000000cc # DDR Address Control
78# bit1-0: 01, Cs0width=x8
79# bit3-2: 10, Cs0size=1Gb
80# bit5-4: 01, Cs1width=x8
81# bit7-6: 10, Cs1size=1Gb
82# bit9-8: 00, Cs2width=nonexistent
83# bit11-10: 00, Cs2size =nonexistent
84# bit13-12: 00, Cs3width=nonexistent
85# bit15-14: 00, Cs3size =nonexistent
86# bit16: 0, Cs0AddrSel
87# bit17: 0, Cs1AddrSel
88# bit18: 0, Cs2AddrSel
89# bit19: 0, Cs3AddrSel
90# bit31-20: 0 required
91
92DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
93# bit0: 0, OpenPage enabled
94# bit31-1: 0 required
95
96DATA 0xFFD01418 0x00000000 # DDR Operation
97# bit3-0: 0x0, DDR cmd
98# bit31-4: 0 required
99
100DATA 0xFFD0141C 0x00000C52 # DDR Mode
101# bit2-0: 2, BurstLen=2 required
102# bit3: 0, BurstType=0 required
103# bit6-4: 4, CL=5
104# bit7: 0, TestMode=0 normal
105# bit8: 0, DLL reset=0 normal
106# bit11-9: 6, auto-precharge write recovery ????????????
107# bit12: 0, PD must be zero
108# bit31-13: 0 required
109
110DATA 0xFFD01420 0x00000040 # DDR Extended Mode
111# bit0: 0, DDR DLL enabled
112# bit1: 0, DDR drive strenght normal
113# bit2: 0, DDR ODT control lsd (disabled)
114# bit5-3: 000, required
115# bit6: 1, DDR ODT control msb, (disabled)
116# bit9-7: 000, required
117# bit10: 0, differential DQS enabled
118# bit11: 0, required
119# bit12: 0, DDR output buffer enabled
120# bit31-13: 0 required
121
122DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
123# bit2-0: 111, required
124# bit3 : 1 , MBUS Burst Chop disabled
125# bit6-4: 111, required
126# bit7 : 0
127# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
128# bit9 : 0 , no half clock cycle addition to dataout
129# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
130# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
131# bit15-12: 1111 required
132# bit31-16: 0 required
133
134DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
135DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
136
137DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
138DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
139# bit0: 1, Window enabled
140# bit1: 0, Write Protect disabled
141# bit3-2: 00, CS0 hit selected
142# bit23-4: ones, required
143# bit31-24: 0x0F, Size (i.e. 256MB)
144
145DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
146DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
147
148DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
149DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
150
151DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low)
152DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
153# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
154# bit3-2: 01, ODT1 active NEVER!
155# bit31-4: zero, required
156
157DATA 0xFFD0149C 0x0000E803 # CPU ODT Control
158DATA 0xFFD01480 0x00000001 # DDR Initialization Control
159#bit0=1, enable DDR init upon this register write
160
161# End of Header extension
162DATA 0x0 0x0