blob: 0f5f85c22a66cd1351132c4478c9ef08b428e511 [file] [log] [blame]
Matthias Fuchs1a3ac862008-01-17 10:53:08 +01001/*
2 * (C) Copyright 2008
3 * Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com
4 *
5 * based on the Sequoia board configuration by
6 * Stefan Roese, Jacqueline Pira-Ferriol and Alain Saurel
7 *
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License as
10 * published by the Free Software Foundation; either version 2 of
11 * the License, or (at your option) any later version.
12 *
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
21 * MA 02111-1307 USA
22 */
23
24/*
25 **********************************************************************
26 * DU440.h - configuration for esd's DU440 board (Power PC440EPx)
27 **********************************************************************
28 */
29#ifndef __CONFIG_H
30#define __CONFIG_H
31
32/*
33 * High Level Configuration Options
34 */
35#define CONFIG_DU440 1 /* Board is esd DU440 */
36#define CONFIG_440EPX 1 /* Specific PPC440EPx */
37#define CONFIG_4xx 1 /* ... PPC4xx family */
38#define CONFIG_SYS_CLK_FREQ 33333400 /* external freq to pll */
39
40#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
41#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
42#define CONFIG_LAST_STAGE_INIT 1 /* last_stage_init */
43
44/*
45 * Base addresses -- Note these are effective addresses where the
46 * actual resources get mapped (not physical addresses)
47 */
48#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
49#define CFG_MALLOC_LEN (8 << 20) /* Reserve 8 MB for malloc() */
50
51#define CFG_BOOT_BASE_ADDR 0xf0000000
52#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
53#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
54#define CFG_MONITOR_BASE TEXT_BASE
55#define CFG_NAND0_ADDR 0xd0000000 /* NAND Flash */
56#define CFG_NAND1_ADDR 0xd0100000 /* NAND Flash */
57#define CFG_OCM_BASE 0xe0010000 /* ocm */
58#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */
59#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
60#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
61#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
62#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
63#define CFG_PCI_IOBASE 0xe8000000
64
65
66/* Don't change either of these */
67#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
68
69#define CFG_USB2D0_BASE 0xe0000100
70#define CFG_USB_DEVICE 0xe0000000
71#define CFG_USB_HOST 0xe0000400
72
73/*
74 * Initial RAM & stack pointer
75 */
76/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
77#define CFG_INIT_RAM_OCM 1 /* OCM as init ram */
78#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
79
80#define CFG_INIT_RAM_END (4 << 10)
81#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
82#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
83#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
84
85/*
86 * Serial Port
87 */
88/* TODO: external clock oscillator will be removed */
89#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
90#define CONFIG_BAUDRATE 115200
91#define CONFIG_SERIAL_MULTI 1
92#undef CONFIG_UART1_CONSOLE
93
94#define CFG_BAUDRATE_TABLE \
95 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
96
97/*
98 * Video Port
99 */
100#define CONFIG_VIDEO
101#define CONFIG_VIDEO_SMI_LYNXEM
102#define CONFIG_CFB_CONSOLE
103#define CONFIG_VIDEO_LOGO
104#define CONFIG_VGA_AS_SINGLE_DEVICE
105#define CONFIG_SPLASH_SCREEN
106#define CONFIG_SPLASH_SCREEN_ALIGN
107#define CONFIG_VIDEO_BMP_GZIP /* gzip compressed bmp images */
108#define CFG_VIDEO_LOGO_MAX_SIZE (4 << 20) /* for decompressed img */
109#define CFG_DEFAULT_VIDEO_MODE 0x31a /* 1280x1024,16bpp */
110#define CFG_CONSOLE_IS_IN_ENV
111#define CFG_ISA_IO CFG_PCI_IOBASE
112
113/*
114 * Environment
115 */
116#define CFG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */
117
118/*
119 * FLASH related
120 */
121#define CFG_FLASH_CFI /* The flash is CFI compatible */
122#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
123
124#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
125
126#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
127#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
128
129#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
130#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
131
132#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
133/* CFI_FLASH_PROTECTION make flash_protect hang sometimes -> disabled */
134#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */
135
136#define CFG_FLASH_EMPTY_INFO
137#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
138
139#ifdef CFG_ENV_IS_IN_FLASH
140#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
141#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
142#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
143
144/* Address and size of Redundant Environment Sector */
145#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
146#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
147#endif
148
149#ifdef CFG_ENV_IS_IN_EEPROM
150#define CFG_ENV_OFFSET 0 /* environment starts at */
151 /* the beginning of the EEPROM */
152#define CFG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */
153#endif
154
155/*
156 * DDR SDRAM
157 */
158#define CFG_MBYTES_SDRAM (1024) /* 512 MiB TODO: remove */
159#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
Matthias Fuchs7c91f512008-03-30 18:01:15 +0200160#define CFG_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
Stefan Roese02e38922008-03-31 12:20:48 +0200161 /* 440EPx errata CHIP 11 */
Matthias Fuchs1a3ac862008-01-17 10:53:08 +0100162#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
Matthias Fuchs1a3ac862008-01-17 10:53:08 +0100163#define CONFIG_DDR_ECC /* Use ECC when available */
164#define SPD_EEPROM_ADDRESS {0x50}
165#define CONFIG_PROG_SDRAM_TLB
166
167/*
168 * I2C
169 */
170#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
171#undef CONFIG_SOFT_I2C /* I2C bit-banged */
172#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
173#define CFG_I2C_SLAVE 0x7F
174#define CONFIG_I2C_CMD_TREE 1
175#define CONFIG_I2C_MULTI_BUS 1
176
177#define CFG_SPD_BUS_NUM 0
178#define IIC1_MCP3021_ADDR 0x4d
179#define IIC1_USB2507_ADDR 0x2c
180#ifdef CONFIG_I2C_MULTI_BUS
181#define CFG_I2C_NOPROBES {{1, IIC1_USB2507_ADDR}}
182#endif
183#define CFG_I2C_MULTI_EEPROMS
184#define CFG_I2C_EEPROM_ADDR 0x54
185#define CFG_I2C_EEPROM_ADDR_LEN 2
186#define CFG_EEPROM_PAGE_WRITE_ENABLE
187#define CFG_EEPROM_PAGE_WRITE_BITS 5
188#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
189#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
190
191#define CFG_EEPROM_WREN 1
192#define CFG_I2C_BOOT_EEPROM_ADDR 0x52
193
194/*
195 * standard dtt sensor configuration - bottom bit will determine local or
196 * remote sensor of the TMP401
197 */
198#define CONFIG_DTT_SENSORS { 0, 1 }
199
200/*
201 * The PMC440 uses a TI TMP401 temperature sensor. This part
202 * is basically compatible to the ADM1021 that is supported
203 * by U-Boot.
204 *
205 * - i2c addr 0x4c
206 * - conversion rate 0x02 = 0.25 conversions/second
207 * - ALERT ouput disabled
208 * - local temp sensor enabled, min set to 0 deg, max set to 70 deg
209 * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg
210 */
211#define CONFIG_DTT_ADM1021
212#define CFG_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
213
214/*
215 * RTC stuff
216 */
217#define CONFIG_RTC_DS1338
218#define CFG_I2C_RTC_ADDR 0x68
219
220#undef CONFIG_BOOTARGS
221
222#define CONFIG_EXTRA_ENV_SETTINGS \
223 "netdev=eth0\0" \
224 "ethrotate=no\0" \
225 "hostname=du440\0" \
226 "nfsargs=setenv bootargs root=/dev/nfs rw " \
227 "nfsroot=${serverip}:${rootpath}\0" \
228 "ramargs=setenv bootargs root=/dev/ram rw\0" \
229 "addip=setenv bootargs ${bootargs} " \
230 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
231 ":${hostname}:${netdev}:off panic=1\0" \
232 "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
233 "flash_self=run ramargs addip addtty optargs;" \
234 "bootm ${kernel_addr} ${ramdisk_addr}\0" \
235 "net_nfs=tftp 200000 ${img};run nfsargs addip addtty optargs;" \
236 "bootm\0" \
237 "rootpath=/tftpboot/du440/target_root_du440\0" \
238 "img=/tftpboot/du440/uImage\0" \
239 "kernel_addr=FFC00000\0" \
240 "ramdisk_addr=FFE00000\0" \
241 "initrd_high=30000000\0" \
242 "load=tftp 100000 /tftpboot/du440/u-boot.bin\0" \
243 "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
244 "cp.b 100000 FFFA0000 60000\0" \
245 ""
Matthias Fuchs1a3ac862008-01-17 10:53:08 +0100246
247#define CONFIG_PREBOOT /* enable preboot variable */
248
249#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
250
251#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
252#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
253
254#ifndef __ASSEMBLY__
255int du440_phy_addr(int devnum);
256#endif
257
258#define CONFIG_IBM_EMAC4_V4 1
259#define CONFIG_MII 1 /* MII PHY management */
260#define CONFIG_PHY_ADDR du440_phy_addr(0) /* PHY address */
261
262#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
Matthias Fuchs7c91f512008-03-30 18:01:15 +0200263#undef CONFIG_PHY_GIGE /* no GbE detection */
Matthias Fuchs1a3ac862008-01-17 10:53:08 +0100264
265#define CONFIG_HAS_ETH0
266#define CFG_RX_ETH_BUFFER 128
267
268#define CONFIG_NET_MULTI 1
269#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
270#define CONFIG_PHY1_ADDR du440_phy_addr(1)
271
272/*
273 * USB
274 */
275#define CONFIG_USB_OHCI_NEW
276#define CONFIG_USB_STORAGE
277#define CFG_OHCI_BE_CONTROLLER
278
279#define CFG_USB_OHCI_CPU_INIT 1
280#define CFG_USB_OHCI_REGS_BASE CFG_USB_HOST
281#define CFG_USB_OHCI_SLOT_NAME "du440"
282#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
283
284/* Comment this out to enable USB 1.1 device */
285#define USB_2_0_DEVICE
286
287/* Partitions */
288#define CONFIG_MAC_PARTITION
289#define CONFIG_DOS_PARTITION
290#define CONFIG_ISO_PARTITION
291
292#include <config_cmd_default.h>
293
Matthias Fuchs7c91f512008-03-30 18:01:15 +0200294#define CONFIG_CMD_AUTOSCRIPT
Matthias Fuchs1a3ac862008-01-17 10:53:08 +0100295#define CONFIG_CMD_BSP
Matthias Fuchs7c91f512008-03-30 18:01:15 +0200296#define CONFIG_CMD_BMP
Matthias Fuchs1a3ac862008-01-17 10:53:08 +0100297#define CONFIG_CMD_DATE
298#define CONFIG_CMD_ASKENV
299#define CONFIG_CMD_DHCP
300#define CONFIG_CMD_DTT
301#define CONFIG_CMD_DIAG
302#define CONFIG_CMD_EEPROM
303#define CONFIG_CMD_ELF
304#define CONFIG_CMD_FAT
305#define CONFIG_CMD_I2C
306#define CONFIG_CMD_IRQ
307#define CONFIG_CMD_MII
308#define CONFIG_CMD_NAND
309#define CONFIG_CMD_NET
310#define CONFIG_CMD_NFS
311#define CONFIG_CMD_PCI
312#define CONFIG_CMD_PING
313#define CONFIG_CMD_USB
314#define CONFIG_CMD_REGINFO
315#define CONFIG_CMD_SDRAM
316
317#define CONFIG_SUPPORT_VFAT
318
319/*
320 * Miscellaneous configurable options
321 */
322#define CFG_LONGHELP /* undef to save memory */
323#define CFG_PROMPT "=> " /* Monitor Command Prompt */
324#if defined(CONFIG_CMD_KGDB)
325#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
326#else
327#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
328#endif
329/* Print Buffer Size */
330#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
331#define CFG_MAXARGS 16 /* max number of command args */
332#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
333
334#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
335#define CFG_MEMTEST_END 0x3f000000 /* 4 ... < 1GB DRAM */
336
337#define CFG_LOAD_ADDR 0x100000 /* default load address */
338#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
339
340#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
341
342#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
343#define CONFIG_LOOPW 1 /* enable loopw command */
344#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
345#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
346#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
347
348#define CONFIG_AUTOBOOT_KEYED 1
349#define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d seconds\n"
350#define CONFIG_AUTOBOOT_DELAY_STR "d"
351#define CONFIG_AUTOBOOT_STOP_STR " "
352
353/*
354 * PCI stuff
355 */
356#define CONFIG_PCI /* include pci support */
357#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */
358#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
359#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
360
361/* Board-specific PCI */
362#define CFG_PCI_TARGET_INIT
363#define CFG_PCI_MASTER_INIT
364
365/*
366 * For booting Linux, the board info and command line data
367 * have to be in the first 8 MB of memory, since this is
368 * the maximum mapped by the Linux kernel during initialization.
369 */
370#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
371
372/*
373 * External Bus Controller (EBC) Setup
374 */
375#define CFG_FLASH CFG_FLASH_BASE
376
377#define CFG_CPLD_BASE 0xC0000000
Wolfgang Denk53677ef2008-05-20 16:00:29 +0200378#define CFG_CPLD_RANGE 0x00000010
Matthias Fuchs1a3ac862008-01-17 10:53:08 +0100379#define CFG_DUMEM_BASE 0xC0100000
Wolfgang Denk53677ef2008-05-20 16:00:29 +0200380#define CFG_DUMEM_RANGE 0x00100000
Matthias Fuchs1a3ac862008-01-17 10:53:08 +0100381#define CFG_DUIO_BASE 0xC0200000
Wolfgang Denk53677ef2008-05-20 16:00:29 +0200382#define CFG_DUIO_RANGE 0x00010000
Matthias Fuchs1a3ac862008-01-17 10:53:08 +0100383
384#define CFG_NAND0_CS 2 /* NAND chip connected to CSx */
385#define CFG_NAND1_CS 3 /* NAND chip connected to CSx */
386/* Memory Bank 0 (NOR-FLASH) initialization */
387#define CFG_EBC_PB0AP 0x04017200
388#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000)
389
390/* Memory Bank 1 (CPLD, 16 bytes needed, but 1MB is minimum) */
391#define CFG_EBC_PB1AP 0x018003c0
392#define CFG_EBC_PB1CR (CFG_CPLD_BASE | 0x18000)
393
394/* Memory Bank 2 (NAND-FLASH) initialization */
395#define CFG_EBC_PB2AP 0x018003c0
396#define CFG_EBC_PB2CR (CFG_NAND0_ADDR | 0x1c000)
397
398/* Memory Bank 3 (NAND-FLASH) initialization */
399#define CFG_EBC_PB3AP 0x018003c0
400#define CFG_EBC_PB3CR (CFG_NAND1_ADDR | 0x1c000)
401
402/* Memory Bank 4 (DUMEM, 1MB) initialization */
403#define CFG_EBC_PB4AP 0x018053c0
404#define CFG_EBC_PB4CR (CFG_DUMEM_BASE | 0x18000)
405
406/* Memory Bank 5 (DUIO, 64KB needed, but 1MB is minimum) */
407#define CFG_EBC_PB5AP 0x018053c0
408#define CFG_EBC_PB5CR (CFG_DUIO_BASE | 0x18000)
409
410/*
411 * NAND FLASH
412 */
413#define CFG_MAX_NAND_DEVICE 2
414#define NAND_MAX_CHIPS CFG_MAX_NAND_DEVICE
415#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
416#define CFG_NAND_BASE_LIST {CFG_NAND0_ADDR + CFG_NAND0_CS, \
417 CFG_NAND1_ADDR + CFG_NAND1_CS}
418
419/*
420 * Internal Definitions
421 *
422 * Boot Flags
423 */
424#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
425#define BOOTFLAG_WARM 0x02 /* Software reboot */
426
427#if defined(CONFIG_CMD_KGDB)
428#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
429#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
430#endif
431
Matthias Fuchs7c91f512008-03-30 18:01:15 +0200432#define CONFIG_AUTOSCRIPT 1
Matthias Fuchs1a3ac862008-01-17 10:53:08 +0100433
434#endif /* __CONFIG_H */