blob: 4f57067db155110ac17c9d545a5febe31d976199 [file] [log] [blame]
Wolfgang Denk8e6f1a82005-09-25 18:59:36 +02001/********************************************************************
2 *
3 * Unless otherwise specified, Copyright (C) 2004-2005 Barco Control Rooms
4 *
5 * $Source: /home/services/cvs/firmware/ppc/u-boot-1.1.2/include/configs/barco.h,v $
6 * $Revision: 1.2 $
7 * $Author: mleeman $
8 * $Date: 2005/02/21 12:48:58 $
9 *
10 * Last ChangeLog Entry
11 * $Log: barco.h,v $
12 * Revision 1.2 2005/02/21 12:48:58 mleeman
13 * update of copyright years (feedback wd)
14 *
15 * Revision 1.1 2005/02/14 09:29:25 mleeman
16 * moved barcohydra.h to barco.h
17 *
18 * Revision 1.4 2005/02/09 12:56:23 mleeman
19 * add generic header to track changes in sources
20 *
21 *
22 *******************************************************************/
23
24/*
25 * (C) Copyright 2001, 2002
26 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
27 *
28 * See file CREDITS for list of people who contributed to this
29 * project.
30 *
31 * This program is free software; you can redistribute it and/or
32 * modify it under the terms of the GNU General Public License as
33 * published by the Free Software Foundation; either version 2 of
34 * the License, or (at your option) any later version.
35 *
36 * This program is distributed in the hope that it will be useful,
37 * but WITHOUT ANY WARRANTY; without even the implied warranty of
38 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
39 * GNU General Public License for more details.
40 *
41 * You should have received a copy of the GNU General Public License
42 * along with this program; if not, write to the Free Software
43 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
44 * MA 02111-1307 USA
45 */
46
47/* ------------------------------------------------------------------------- */
48
49/*
50 * board/config.h - configuration options, board specific
51 */
52
53#ifndef __CONFIG_H
54#define __CONFIG_H
55
56/*
57 * High Level Configuration Options
58 * (easy to change)
59 */
60
61#define CONFIG_MPC824X 1
62#define CONFIG_MPC8245 1
63#define CONFIG_BARCOBCD_STREAMING 1
64
65#undef USE_DINK32
66
67#define CONFIG_CONS_INDEX 3 /* set to '3' for on-chip DUART */
68#define CONFIG_BAUDRATE 9600
69#define CONFIG_DRAM_SPEED 100 /* MHz */
70
71#define CONFIG_BOOTARGS "mem=32M"
72
Jon Loeliger2fd90ce2007-07-09 21:48:26 -050073
74/*
75 * BOOTP options
Wolfgang Denk8e6f1a82005-09-25 18:59:36 +020076 */
Jon Loeliger2fd90ce2007-07-09 21:48:26 -050077#define CONFIG_BOOTP_SUBNETMASK
78#define CONFIG_BOOTP_GATEWAY
79#define CONFIG_BOOTP_HOSTNAME
80#define CONFIG_BOOTP_BOOTPATH
81#define CONFIG_BOOTP_BOOTFILESIZE
82#define CONFIG_BOOTP_DNS
83
Wolfgang Denk8e6f1a82005-09-25 18:59:36 +020084
Jon Loeligerba2351f2007-07-04 22:31:49 -050085/*
86 * Command line configuration.
87 */
88#include <config_cmd_default.h>
Wolfgang Denk8e6f1a82005-09-25 18:59:36 +020089
Jon Loeligerba2351f2007-07-04 22:31:49 -050090#define CONFIG_CMD_ELF
91#define CONFIG_CMD_I2C
92#define CONFIG_CMD_EEPROM
93#define CONFIG_CMD_PCI
94
Jon Loeliger80ff4f92007-07-10 09:29:01 -050095#undef CONFIG_CMD_NET
96
Wolfgang Denk8e6f1a82005-09-25 18:59:36 +020097
98#define CONFIG_HUSH_PARSER 1 /* use "hush" command parser */
Wolfgang Denk53677ef2008-05-20 16:00:29 +020099#define CONFIG_BOOTDELAY 1
100#define CONFIG_BOOTCOMMAND "boot_default"
Wolfgang Denk8e6f1a82005-09-25 18:59:36 +0200101
102/*
103 * Miscellaneous configurable options
104 */
105#define CFG_LONGHELP 1 /* undef to save memory */
106#define CFG_PROMPT "=> " /* Monitor Command Prompt */
107#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
108#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
109#define CFG_MAXARGS 16 /* max number of command args */
110#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
111#define CFG_LOAD_ADDR 0x00100000 /* default load address */
112#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
113
114
115/*-----------------------------------------------------------------------
116 * PCI stuff
117 *-----------------------------------------------------------------------
118 */
119#define CONFIG_PCI /* include pci support */
120#undef CONFIG_PCI_PNP
Wolfgang Denk8e6f1a82005-09-25 18:59:36 +0200121
122#define PCI_ENET0_IOADDR 0x80000000
123#define PCI_ENET0_MEMADDR 0x80000000
124#define PCI_ENET1_IOADDR 0x81000000
125#define PCI_ENET1_MEMADDR 0x81000000
126
127
128/*-----------------------------------------------------------------------
129 * Start addresses for the final memory configuration
130 * (Set up by the startup code)
131 * Please note that CFG_SDRAM_BASE _must_ start at 0
132 */
133#define CFG_SDRAM_BASE 0x00000000
134#define CFG_MAX_RAM_SIZE 0x02000000
135
136#define CONFIG_LOGBUFFER
137#ifdef CONFIG_LOGBUFFER
Wolfgang Denk53677ef2008-05-20 16:00:29 +0200138#define CFG_STDOUT_ADDR 0x1FFC000
Wolfgang Denk8e6f1a82005-09-25 18:59:36 +0200139#else
Wolfgang Denk53677ef2008-05-20 16:00:29 +0200140#define CFG_STDOUT_ADDR 0x2B9000
Wolfgang Denk8e6f1a82005-09-25 18:59:36 +0200141#endif
142
143#define CFG_RESET_ADDRESS 0xFFF00100
144
145#if defined (USE_DINK32)
146#define CFG_MONITOR_LEN 0x00030000
147#define CFG_MONITOR_BASE 0x00090000
148#define CFG_RAMBOOT 1
149#define CFG_INIT_RAM_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
150#define CFG_INIT_RAM_END 0x10000
151#define CFG_GBL_DATA_SIZE 256 /* size in bytes reserved for initial data */
152#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
153#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
154#else
155#undef CFG_RAMBOOT
156#define CFG_MONITOR_LEN 0x00030000
157#define CFG_MONITOR_BASE TEXT_BASE
158
159#define CFG_GBL_DATA_SIZE 128
160
Wolfgang Denk53677ef2008-05-20 16:00:29 +0200161#define CFG_INIT_RAM_ADDR 0x40000000
162#define CFG_INIT_RAM_END 0x1000
163#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
Wolfgang Denk8e6f1a82005-09-25 18:59:36 +0200164
165#endif
166
167#define CFG_FLASH_BASE 0xFFF00000
168#define CFG_FLASH_SIZE (8 * 1024 * 1024) /* Unity has onboard 1MByte flash */
169#define CFG_ENV_IS_IN_FLASH 1
170#define CFG_ENV_OFFSET 0x000047A4 /* Offset of Environment Sector */
171#define CFG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */
Wolfgang Denkf57f70a2005-10-13 01:45:54 +0200172/* #define ENV_CRC 0x8BF6F24B XXX - FIXME: gets defined automatically */
Wolfgang Denk8e6f1a82005-09-25 18:59:36 +0200173
174#define CFG_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */
175
176#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
177#define CFG_MEMTEST_END 0x04000000 /* 0 ... 32 MB in DRAM */
178
179#define CFG_EUMB_ADDR 0xFDF00000
180
181#define CFG_FLASH_RANGE_BASE 0xFFC00000 /* flash memory address range */
182#define CFG_FLASH_RANGE_SIZE 0x00400000
183#define FLASH_BASE0_PRELIM 0xFFF00000 /* sandpoint flash */
184#define FLASH_BASE1_PRELIM 0xFF000000 /* PMC onboard flash */
185
186/*
187 * select i2c support configuration
188 *
189 * Supported configurations are {none, software, hardware} drivers.
190 * If the software driver is chosen, there are some additional
191 * configuration items that the driver uses to drive the port pins.
192 */
193#define CONFIG_HARD_I2C 1 /* To enable I2C support */
194#undef CONFIG_SOFT_I2C /* I2C bit-banged */
195#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
196#define CFG_I2C_SLAVE 0x7F
197
198#ifdef CONFIG_SOFT_I2C
199#error "Soft I2C is not configured properly. Please review!"
200#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
201#define I2C_ACTIVE (iop->pdir |= 0x00010000)
202#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
203#define I2C_READ ((iop->pdat & 0x00010000) != 0)
204#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
205 else iop->pdat &= ~0x00010000
206#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
207 else iop->pdat &= ~0x00020000
208#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
209#endif /* CONFIG_SOFT_I2C */
210
211#define CFG_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */
212#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
213#define CFG_EEPROM_PAGE_WRITE_BITS 3
214#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
215
216#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
217#define CFG_FLASH_BANKS { FLASH_BASE0_PRELIM , FLASH_BASE1_PRELIM }
218#define CFG_DBUS_SIZE2 1
219
220/*-----------------------------------------------------------------------
221 * Definitions for initial stack pointer and data area (in DPRAM)
222 */
223
224
225 /*
226 * NS16550 Configuration (internal DUART)
227 */
228 /*
229 * Low Level Configuration Settings
230 * (address mappings, register initial values, etc.)
231 * You should know what you are doing if you make changes here.
232 */
233
234#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
235
236#define CFG_ROMNAL 0x0F /*rom/flash next access time */
237#define CFG_ROMFAL 0x1E /*rom/flash access time */
238
239#define CFG_REFINT 0x8F /* no of clock cycles between CBR refresh cycles */
240
241/* the following are for SDRAM only*/
242#define CFG_BSTOPRE 0x25C /* Burst To Precharge, sets open page interval */
243#define CFG_REFREC 8 /* Refresh to activate interval */
244#define CFG_RDLAT 4 /* data latency from read command */
245#define CFG_PRETOACT 3 /* Precharge to activate interval */
246#define CFG_ACTTOPRE 5 /* Activate to Precharge interval */
247#define CFG_ACTORW 2 /* Activate to R/W */
248#define CFG_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */
249#define CFG_SDMODE_WRAP 0 /* SDMODE wrap type */
250
251#define CFG_REGISTERD_TYPE_BUFFER 1
252#define CFG_EXTROM 0
253#define CFG_REGDIMM 0
254
255
256/* memory bank settings*/
257/*
258 * only bits 20-29 are actually used from these vales to set the
259 * start/end address the upper two bits will be 0, and the lower 20
260 * bits will be set to 0x00000 for a start address, or 0xfffff for an
261 * end address
262 */
263#define CFG_BANK0_START 0x00000000
264#define CFG_BANK0_END 0x01FFFFFF
265#define CFG_BANK0_ENABLE 1
266#define CFG_BANK1_START 0x02000000
267#define CFG_BANK1_END 0x02ffffff
268#define CFG_BANK1_ENABLE 0
269#define CFG_BANK2_START 0x03f00000
270#define CFG_BANK2_END 0x03ffffff
271#define CFG_BANK2_ENABLE 0
272#define CFG_BANK3_START 0x04000000
273#define CFG_BANK3_END 0x04ffffff
274#define CFG_BANK3_ENABLE 0
275#define CFG_BANK4_START 0x05000000
276#define CFG_BANK4_END 0x05FFFFFF
277#define CFG_BANK4_ENABLE 0
278#define CFG_BANK5_START 0x06000000
279#define CFG_BANK5_END 0x06FFFFFF
280#define CFG_BANK5_ENABLE 0
281#define CFG_BANK6_START 0x07000000
282#define CFG_BANK6_END 0x07FFFFFF
283#define CFG_BANK6_ENABLE 0
284#define CFG_BANK7_START 0x08000000
285#define CFG_BANK7_END 0x08FFFFFF
286#define CFG_BANK7_ENABLE 0
287/*
288 * Memory bank enable bitmask, specifying which of the banks defined above
289 are actually present. MSB is for bank #7, LSB is for bank #0.
290 */
291#define CFG_BANK_ENABLE 0x01
292
293#define CFG_ODCR 0xff /* configures line driver impedances, */
294 /* see 8240 book for bit definitions */
295#define CFG_PGMAX 0x32 /* how long the 8240 retains the */
296 /* currently accessed page in memory */
297 /* see 8240 book for details */
298
299/* SDRAM 0 - 256MB */
300#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
301#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
302
303/* stack in DCACHE @ 1GB (no backing mem) */
304#if defined(USE_DINK32)
305#define CFG_IBAT1L (0x40000000 | BATL_PP_00 )
306#define CFG_IBAT1U (0x40000000 | BATU_BL_128K )
307#else
308#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
309#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
310#endif
311
312/* PCI memory */
313#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
314#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
315
316/* Flash, config addrs, etc */
317#define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
318#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
319
320#define CFG_DBAT0L CFG_IBAT0L
321#define CFG_DBAT0U CFG_IBAT0U
322#define CFG_DBAT1L CFG_IBAT1L
323#define CFG_DBAT1U CFG_IBAT1U
324#define CFG_DBAT2L CFG_IBAT2L
325#define CFG_DBAT2U CFG_IBAT2U
326#define CFG_DBAT3L CFG_IBAT3L
327#define CFG_DBAT3U CFG_IBAT3U
328
329/*
330 * For booting Linux, the board info and command line data
331 * have to be in the first 8 MB of memory, since this is
332 * the maximum mapped by the Linux kernel during initialization.
333 */
334#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
335/*-----------------------------------------------------------------------
336 * FLASH organization
337 */
338#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
339#define CFG_MAX_FLASH_SECT 20 /* max number of sectors on one chip */
340
341#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
342#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
343
344#define CFG_FLASH_CHECKSUM
345
346/*-----------------------------------------------------------------------
347 * Cache Configuration
348 */
349#define CFG_CACHELINE_SIZE 32 /* For MPC8240 CPU */
Jon Loeligerba2351f2007-07-04 22:31:49 -0500350#if defined(CONFIG_CMD_KGDB)
Wolfgang Denk8e6f1a82005-09-25 18:59:36 +0200351# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
352#endif
353
354
355/*
356 * Internal Definitions
357 *
358 * Boot Flags
359 */
360#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
361#define BOOTFLAG_WARM 0x02 /* Software reboot */
362
363/* values according to the manual */
364
365#define CONFIG_DRAM_50MHZ 1
366#define CONFIG_SDRAM_50MHZ
367
368#define CONFIG_DISK_SPINUP_TIME 1000000
369
370
371#endif /* __CONFIG_H */