| Wenyou Yang | 25e88d4 | 2017-04-18 13:49:34 +0800 | [diff] [blame] | 1 | /* |
| 2 | * at91sam9g25ek.dts - Device Tree file for AT91SAM9G25-EK board |
| 3 | * |
| 4 | * Copyright (C) 2012 Atmel, |
| 5 | * 2012 Nicolas Ferre <nicolas.ferre@atmel.com> |
| 6 | * |
| 7 | * Licensed under GPLv2 or later. |
| 8 | */ |
| 9 | /dts-v1/; |
| 10 | #include "at91sam9g25.dtsi" |
| 11 | #include "at91sam9x5ek.dtsi" |
| 12 | |
| 13 | / { |
| 14 | model = "Atmel AT91SAM9G25-EK"; |
| 15 | compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9"; |
| 16 | |
| 17 | ahb { |
| 18 | apb { |
| 19 | spi0: spi@f0000000 { |
| 20 | status = "disabled"; |
| 21 | }; |
| 22 | |
| 23 | mmc1: mmc@f000c000 { |
| 24 | status = "disabled"; |
| 25 | }; |
| 26 | |
| 27 | i2c0: i2c@f8010000 { |
| 28 | ov2640: camera@0x30 { |
| 29 | compatible = "ovti,ov2640"; |
| 30 | reg = <0x30>; |
| 31 | pinctrl-names = "default"; |
| 32 | pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; |
| 33 | resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>; |
| 34 | pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>; |
| 35 | clocks = <&pck0>; |
| 36 | clock-names = "xvclk"; |
| 37 | assigned-clocks = <&pck0>; |
| 38 | assigned-clock-rates = <25000000>; |
| 39 | status = "okay"; |
| 40 | |
| 41 | port { |
| 42 | ov2640_0: endpoint { |
| 43 | remote-endpoint = <&isi_0>; |
| 44 | bus-width = <8>; |
| 45 | }; |
| 46 | }; |
| 47 | }; |
| 48 | }; |
| 49 | |
| 50 | macb0: ethernet@f802c000 { |
| 51 | phy-mode = "rmii"; |
| 52 | status = "okay"; |
| 53 | }; |
| 54 | |
| 55 | isi: isi@f8048000 { |
| 56 | status = "okay"; |
| 57 | port { |
| 58 | isi_0: endpoint@0 { |
| 59 | reg = <0>; |
| 60 | remote-endpoint = <&ov2640_0>; |
| 61 | bus-width = <8>; |
| 62 | vsync-active = <1>; |
| 63 | hsync-active = <1>; |
| 64 | }; |
| 65 | }; |
| 66 | }; |
| 67 | }; |
| 68 | }; |
| 69 | }; |