blob: 4f7824ae4007e0185f7db64768693e95aeb33d7c [file] [log] [blame]
Michal Simek917c5782019-03-27 20:14:19 +01001// SPDX-License-Identifier: GPL-2.0
2/*
3 * dts file for Xilinx Versal a2197 RevA System Controller
4 *
5 * (C) Copyright 2019, Xilinx, Inc.
6 *
7 * Michal Simek <michal.simek@xilinx.com>
8 */
9/dts-v1/;
10
11#include "zynqmp.dtsi"
12#include "zynqmp-clk-ccf.dtsi"
13#include <dt-bindings/gpio/gpio.h>
14
15/ {
16 model = "Versal System Controller on a2197 Processor Char board RevA"; /* Tenzing */
Michal Simek50d92832019-06-28 13:16:10 +020017 compatible = "xlnx,zynqmp-p-a2197-00-revA", "xlnx,zynqmp-a2197-revA",
Michal Simek917c5782019-03-27 20:14:19 +010018 "xlnx,zynqmp-a2197", "xlnx,zynqmp";
19
20 aliases {
21 ethernet0 = &gem0;
22 gpio0 = &gpio;
23 i2c0 = &i2c0;
24 i2c1 = &i2c1;
25 mmc0 = &sdhci0;
26 mmc1 = &sdhci1;
27 rtc0 = &rtc;
28 serial0 = &uart0;
29 serial1 = &uart1;
30 serial2 = &dcc;
31 usb0 = &usb0;
32 usb1 = &usb1;
33 };
34
35 chosen {
36 bootargs = "earlycon";
37 stdout-path = "serial0:115200n8";
38 xlnx,eeprom = <&eeprom>;
39 /* xlnx,fmc-eeprom = FIXME */
40 };
41
42 memory@0 {
43 device_type = "memory";
Michal Simek5dc8f692019-10-14 10:35:03 +020044 reg = <0x0 0x0 0x0 0x80000000>;
Michal Simek917c5782019-03-27 20:14:19 +010045 };
46};
47
48&sdhci0 { /* emmc MIO 13-23 - with some settings 16GB */
49 status = "okay";
50 non-removable;
51 disable-wp;
52 bus-width = <8>;
Michal Simek01a6da12020-07-22 17:42:43 +020053 xlnx,mio-bank = <0>;
Michal Simek917c5782019-03-27 20:14:19 +010054};
55
56&uart0 { /* uart0 MIO38-39 */
57 status = "okay";
58 u-boot,dm-pre-reloc;
59};
60
61&uart1 { /* uart1 MIO40-41 */
62 status = "okay";
63 u-boot,dm-pre-reloc;
64};
65
66&sdhci1 { /* sd1 MIO45-51 cd in place */
67 status = "okay";
68 no-1-8-v;
69 disable-wp;
Michal Simek01a6da12020-07-22 17:42:43 +020070 xlnx,mio-bank = <1>;
Michal Simek917c5782019-03-27 20:14:19 +010071};
72
73&gem0 {
74 status = "okay";
75 phy-handle = <&phy0>;
76 phy-mode = "sgmii"; /* DTG generates this properly 1512 */
77 is-internal-pcspma;
78 /* phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>; */
Michal Simek2975a422019-08-08 12:44:22 +020079 phy0: ethernet-phy@0 {
Michal Simek917c5782019-03-27 20:14:19 +010080 reg = <0>;
81 };
82};
83
84&gpio {
85 status = "okay";
86 gpio-line-names = "", "", "", "", "", /* 0 - 4 */
87 "", "", "DC_SYS_CTRL0", "DC_SYS_CTRL1", "DC_SYS_CTRL2", /* 5 - 9 */
88 "DC_SYS_CTRL3", "DC_SYS_CTRL4", "DC_SYS_CTRL5", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
89 "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
90 "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "", /* 20 - 24 */
91 "", "", "", "", "", /* 25 - 29 */
92 "", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */
93 "LP_I2C0_PMC_SDA", "LP_I2C1_SCL", "LP_I2C1_SDA", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */
94 "UART1_TXD_OUT", "UART1_RXD_IN", "ETH_RESET_B", "", "", /* 40 - 44 */
95 "SD1_CD_B", "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3", /* 45 - 49 */
96 "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */
97 "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */
98 "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK", /* 60 - 64 */
99 "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1", /* 65 - 69 */
100 "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6", /* 70 - 74 */
101 "USB1_DATA7", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */
102 "SYSCTLR_VERSAL_MODE0", "SYSCTLR_VERSAL_MODE1", /* 78 - 79 */
103 "SYSCTLR_VERSAL_MODE2", "SYSCTLR_VERSAL_MODE3", "SYSCTLR_POR_B_LS", "DC_PRSNT", "SYSCTLR_POWER_EN", /* 80 - 84 */
104 "SYSCTLR_JTAG_S0", "SYSCTLR_JTAG_S1", "SYSCTLR_IIC_MUX0_RESET_B", "SYSCTLR_IIC_MUX1_RESET_B", "SYSCTLR_LP_I2C_SM_ALERT", /* 85 -89 */
105 "SYSCTLR_GPIO0", "SYSCTLR_GPIO1", "SYSCTLR_GPIO2", "SYSCTLR_GPIO3", "SYSCTLR_GPIO4", /* 90 - 94 */
106 "SYSCTLR_GPIO5", "VCCO_500_RBIAS", "VCCO_501_RBIAS", "VCCO_502_RBIAS", "VCCO_500_RBIAS_LED", /* 95 - 99 */
107 "VCCO_501_RBIAS_LED", "VCCO_502_RBIAS_LED", "SYSCTLR_VCCINT_EN", "SYSCTLR_VCC_IO_SOC_EN", "SYSCTLR_VCC_PMC_EN", /* 100 - 104 */
108 "SYSCTLR_VCC_RAM_EN", "SYSCTLR_VCC_PSLP_EN", "SYSCTLR_VCC_PSFP_EN", "SYSCTLR_VCCAUX_EN", "SYSCTLR_VCCAUX_PMC_EN", /* 105 - 109 */
109 "SYSCTLR_VCCO_500_EN", "SYSCTLR_VCCO_501_EN", "SYSCTLR_VCCO_502_EN", "SYSCTLR_VCCO_503_EN", "SYSCTLR_VCC1V8_EN", /* 110 - 114 */
110 "SYSCTLR_VCC3V3_EN", "SYSCTLR_VCC1V2_DDR4_EN", "SYSCTLR_VCC1V1_LP4_EN", "SYSCTLR_VDD1_1V8_LP4_EN", "SYSCTLR_VADJ_FMC_EN", /* 115 - 119 */
111 "SYSCTLR_MGTYAVCC_EN", "SYSCTLR_MGTYAVTT_EN", "SYSCTLR_MGTYVCCAUX_EN", "SYSCTLR_UTIL_1V13_EN", "SYSCTLR_UTIL_1V8_EN", /* 120 - 124 */
112 "SYSCTLR_UTIL_2V5_EN", "FMCP1_FMC_PRSNT_M2C_B", "FMCP2_FMC_PRSNT_M2C_B", "FMCP1_FMCP_PRSNT_M2C_B", "FMCP2_FMCP_PRSNT_M2C_B", /* 125 - 129 */
113 "PMBUS1_INA226_ALERT", "PMBUS2_INA226_ALERT", "SYSCTLR_USBC_SBU1", "SYSCTLR_USBC_SBU2", "TI_CABLE1", /* 130 - 134 */
114 "TI_CABLE2", "SYSCTLR_MIC2005_EN_B", "SYSCTLR_MIC2005_FAULT_B", "SYSCTLR_TUSB320_INT_B", "SYSCTLR_TUSB320_ID", /* 135 - 139 */
115 "PMBUS1_ALERT", "PMBUS2_ALERT", "SYSCTLR_ETH_RESET_B", "SYSCTLR_VCC0V85_TG", "MAX6643_OT_B", /* 140 - 144 */
116 "MAX6643_FANFINAL_B", "MAX6643_FULLSPD", "", "", "", /* 145 - 149 */
117 "", "", "", "", "", /* 150 - 154 */
118 "", "", "", "", "", /* 155 - 159 */
119 "", "", "", "", "", /* 160 - 164 */
120 "", "", "", "", "", /* 165 - 169 */
121 "", "", "", ""; /* 170 - 174 */
122};
123
124&i2c0 { /* MIO 34-35 - can't stay here */
125 status = "okay";
126 clock-frequency = <400000>;
127 i2c-mux@74 { /* u33 */
128 compatible = "nxp,pca9548";
129 #address-cells = <1>;
130 #size-cells = <0>;
131 reg = <0x74>;
132 /* reset-gpios = <&gpio SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
133 i2c@0 { /* PMBUS1 */
134 #address-cells = <1>;
135 #size-cells = <0>;
136 reg = <0>;
137 /* On connector J98 */
138 reg_vcc_fmc: tps544@7 { /* u80 - FIXME name - don't know what it does */
139 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
140 reg = <0x7>;
141 regulator-name = "reg_vcc_fmc";
142 regulator-min-microvolt = <1800000>;
143 regulator-max-microvolt = <2600000>;
144 /* enable-gpio = <&gpio0 23 0x4>; optional */
145 };
146 reg_vcc_ram: tps544@8 { /* u83 - FIXME name - don't know what it does */
147 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
148 reg = <0x8>;
149 };
150 reg_vcc_pslp: tps544@9 { /* u85 - FIXME name - don't know what it does */
151 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
152 reg = <0x9>;
153 };
154 reg_vcc_psfp: tps544@a { /* u86 - FIXME name - don't know what it does */
155 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
156 reg = <0xa>;
157 };
Nishant Mittal74ef6202019-07-24 14:58:52 +0530158 reg_vccint: tps53681@60 { /* u70 - FIXME name - don't know what it does - also vcc_io_soc */
Nishant Mittalebb28f22019-07-24 14:58:52 +0530159 compatible = "ti,tps53681", "ti,tps53679";
Nishant Mittal74ef6202019-07-24 14:58:52 +0530160 reg = <0x60>;
Michal Simek917c5782019-03-27 20:14:19 +0100161 /* vccint, vcc_io_soc */
162 };
163 };
164 i2c@1 { /* PMBUS1_INA226 */
165 #address-cells = <1>;
166 #size-cells = <0>;
167 reg = <1>;
Michal Simeke0c08232019-10-14 10:27:42 +0200168 /* FIXME check alerts coming to SC */
Michal Simek917c5782019-03-27 20:14:19 +0100169 vcc_fmc: ina226@42 { /* u81 */
170 compatible = "ti,ina226";
171 reg = <0x42>;
172 shunt-resistor = <5000>;
173 };
174 vcc_ram: ina226@43 { /* u82 */
175 compatible = "ti,ina226";
176 reg = <0x43>;
177 shunt-resistor = <5000>;
178 };
179 vcc_pslp: ina226@44 { /* u84 */
180 compatible = "ti,ina226";
181 reg = <0x44>;
182 shunt-resistor = <5000>;
183 };
184 vcc_psfp: ina226@45 { /* u87 */
185 compatible = "ti,ina226";
186 reg = <0x45>;
187 shunt-resistor = <5000>;
188 };
189 };
190 i2c@2 { /* PMBUS2 */
191 #address-cells = <1>;
192 #size-cells = <0>;
193 reg = <2>;
194 /* On connector J104 */
195 reg_vccaus: tps544@d { /* u88 - FIXME name - don't know what it does */
196 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
197 reg = <0xd>;
198 };
199 reg_vccaux_fmc: tps544@e { /* u90 - FIXME name - don't know what it does */
200 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
201 reg = <0xe>;
202 };
203 reg_vcco_500: tps544@f { /* u93 - FIXME name - don't know what it does */
204 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
205 reg = <0xf>;
206 };
207 reg_vcco_501: tps544@10 { /* u95 - FIXME name - don't know what it does */
208 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
209 reg = <0x10>;
210 };
211 reg_vcco_502: tps544@11 { /* u97 - FIXME name - don't know what it does */
212 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
213 reg = <0x11>;
214 };
215 reg_vcco_503: tps544@12 { /* u99 - FIXME name - don't know what it does */
216 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
217 reg = <0x12>;
218 };
219 reg_vcc1v8: tps544@13 { /* u101 - FIXME name - don't know what it does */
220 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
221 reg = <0x13>;
222 };
223 reg_vcc3v3: tps544@14 { /* u102 - FIXME name - don't know what it does */
224 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
225 reg = <0x14>;
226 };
227 reg_vcc1v2_ddr4: tps544@15 { /* u104 - FIXME name - don't know what it does */
228 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
229 reg = <0x15>;
230 };
231 reg_vcc1v1_lp4: tps544@16 { /* u106 - FIXME name - don't know what it does */
232 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
233 reg = <0x16>;
234 };
235 reg_vcc1_1V8_lp4: tps544@17 { /* u108 - FIXME name - don't know what it does */
236 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
237 reg = <0x17>;
238 };
239 reg_vadj_fmc: tps544@19 { /* u109 - FIXME name - don't know what it does */
240 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
241 reg = <0x19>;
242 };
243 reg_mgtyavcc: tps544@1a { /* u111 - FIXME name - don't know what it does */
244 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
245 reg = <0x1a>;
246 };
247 reg_mgtyavtt: tps544@1b { /* u114 - FIXME name - don't know what it does */
248 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
249 reg = <0x1b>;
250 };
251 reg_mgtyvccaux: tps544@1c { /* u115 - FIXME name - don't know what it does */
252 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
253 reg = <0x1c>;
254 };
255 reg_util_1v13: tps544@1d { /* u117 - FIXME name - don't know what it does */
256 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
257 reg = <0x1d>;
258 };
259 reg_util_1v8: tps544@1e { /* u118 - FIXME name - don't know what it does */
260 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
261 reg = <0x1e>;
262 };
263 reg_util_2v5: tps544@1f { /* u119 - FIXME name - don't know what it does */
264 compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
265 reg = <0x1f>;
266 };
267 };
268 i2c@3 { /* PMBUS2_INA226 */
269 #address-cells = <1>;
270 #size-cells = <0>;
271 reg = <3>;
272 /* FIXME check alerts coming to SC */
273 vccaux: ina226@40 { /* u89 */
274 compatible = "ti,ina226";
275 reg = <0x40>;
276 shunt-resistor = <5000>;
277 };
278 vccaux_fmc: ina226@41 { /* u91 */
279 compatible = "ti,ina226";
280 reg = <0x41>;
281 shunt-resistor = <5000>;
282 };
283 vcco_500: ina226@42 { /* u92 */
284 compatible = "ti,ina226";
285 reg = <0x42>;
286 shunt-resistor = <5000>;
287 };
288 vcco_501: ina226@43 { /* u94 */
289 compatible = "ti,ina226";
290 reg = <0x43>;
291 shunt-resistor = <5000>;
292 };
293 vcco_502: ina226@44 { /* u96 */
294 compatible = "ti,ina226";
295 reg = <0x44>;
296 shunt-resistor = <5000>;
297 };
298 vcco_503: ina226@45 { /* u98 */
299 compatible = "ti,ina226";
300 reg = <0x45>;
301 shunt-resistor = <5000>;
302 };
303 vcc_1v8: ina226@46 { /* u100 */
304 compatible = "ti,ina226";
305 reg = <0x46>;
306 shunt-resistor = <5000>;
307 };
308 vcc_3v3: ina226@47 { /* u103 */
309 compatible = "ti,ina226";
310 reg = <0x47>;
311 shunt-resistor = <5000>;
312 };
313 vcc_1v2_ddr4: ina226@48 { /* u105 */
314 compatible = "ti,ina226";
315 reg = <0x48>;
316 shunt-resistor = <1000>;
317 };
318 vcc1v1_lp4: ina226@49 { /* u107 */
319 compatible = "ti,ina226";
320 reg = <0x49>;
321 shunt-resistor = <5000>;
322 };
323 vadj_fmc: ina226@4a { /* u110 */
324 compatible = "ti,ina226";
325 reg = <0x4a>;
326 shunt-resistor = <5000>;
327 };
328 mgtyavcc: ina226@4b { /* u112 */
329 compatible = "ti,ina226";
330 reg = <0x4b>;
331 shunt-resistor = <1000>;
332 };
333 mgtyavtt: ina226@4c { /* u113 */
334 compatible = "ti,ina226";
335 reg = <0x4c>;
336 shunt-resistor = <1000>;
337 };
338 mgtyvccaux: ina226@4d { /* u116 */
339 compatible = "ti,ina226";
340 reg = <0x4d>;
341 shunt-resistor = <5000>;
342 };
343 vcc_bat: ina226@4e { /* u12 */
344 compatible = "ti,ina226";
345 reg = <0x4e>;
346 shunt-resistor = <10000000>; /* 10 ohm */
347 };
348 };
349 i2c@4 { /* LP_I2C_SM */
350 #address-cells = <1>;
351 #size-cells = <0>;
352 reg = <4>;
353 /* connected to J212G */
354 /* zynqmp sm alert or samtec J212H */
355 };
356 /* 5-7 unused */
357 };
358};
359
360&i2c1 { /* i2c1 MIO 36-37 */
361 status = "okay";
362 clock-frequency = <400000>;
363
364 /* Must be enabled via J242 */
365 eeprom_versal: eeprom@51 { /* x-prc-01-revA u116, x-prc-02-revA u12 */
366 compatible = "atmel,24c02";
367 reg = <0x51>;
368 };
369
370 i2c-mux@74 { /* u35 */
371 compatible = "nxp,pca9548";
372 #address-cells = <1>;
373 #size-cells = <0>;
374 reg = <0x74>;
375 /* reset-gpios = <&gpio SYSCTLR_IIC_MUX1_RESET_B GPIO_ACTIVE_HIGH>; */
376 dc_i2c: i2c@0 { /* DC_I2C */
377 #address-cells = <1>;
378 #size-cells = <0>;
379 reg = <0>;
380 /* Use for storing information about SC board */
381 eeprom: eeprom@54 { /* u34 - m24128 16kB */
382 compatible = "st,24c128", "atmel,24c128";
383 reg = <0x54>;
384 };
385 si570_ref_clk: clock-generator@5d { /* u32 */
386 #clock-cells = <0>;
387 compatible = "silabs,si570";
388 reg = <0x5d>; /* 570JAC000900DG */
389 temperature-stability = <50>;
Michal Simekbdd368a2019-06-25 08:55:52 +0200390 factory-fout = <33333333>;
Michal Simek917c5782019-03-27 20:14:19 +0100391 clock-frequency = <33333333>;
Michal Simekbdd368a2019-06-25 08:55:52 +0200392 clock-output-names = "ref_clk";
Michal Simek917c5782019-03-27 20:14:19 +0100393 };
394 /* Connection via Samtec J212D */
395 /* Use for storing information about X-PRC card */
396 x_prc_eeprom: eeprom@52 { /* x-prc-01-revA u120, x-prc-02-revA u16 */
397 compatible = "atmel,24c02";
398 reg = <0x52>;
399 };
400
401 /* Use for setting up certain features on X-PRC card */
402 x_prc_tca9534: gpio@22 { /* x-prc-01-revA u121, x-prc-02-revA u17 */
403 compatible = "nxp,pca9534";
404 reg = <0x22>;
405 gpio-controller; /* IRQ not connected */
406 #gpio-cells = <2>;
407 gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4",
408 "", "", "", "";
409 gtr_sel0 {
410 gpio-hog;
411 gpios = <0 0>;
412 input; /* FIXME add meaning */
413 line-name = "sw4_1";
414 };
415 gtr_sel1 {
416 gpio-hog;
417 gpios = <1 0>;
418 input; /* FIXME add meaning */
419 line-name = "sw4_2";
420 };
421 gtr_sel2 {
422 gpio-hog;
423 gpios = <2 0>;
424 input; /* FIXME add meaning */
425 line-name = "sw4_3";
426 };
427 gtr_sel3 {
428 gpio-hog;
429 gpios = <3 0>;
430 input; /* FIXME add meaning */
431 line-name = "sw4_4";
432 };
433 };
434 };
435 i2c@1 { /* FMCP1_IIC */
436 #address-cells = <1>;
437 #size-cells = <0>;
438 reg = <1>;
439 /* FIXME connection to Samtec J51C */
440 /* expected eeprom 0x50 SE cards */
441 };
442 i2c@2 { /* FMCP2_IIC */
443 #address-cells = <1>;
444 #size-cells = <0>;
445 reg = <2>;
446 /* FIXME connection to Samtec J53C */
447 /* expected eeprom 0x50 SE cards */
448 };
449 i2c@3 { /* DDR4_DIMM1 */
450 #address-cells = <1>;
451 #size-cells = <0>;
452 reg = <3>;
453 si570_ddr_dimm1: clock-generator@60 { /* u2 */
454 #clock-cells = <0>;
455 compatible = "silabs,si570";
456 reg = <0x60>; /* 570BAB000299DG */
457 temperature-stability = <50>;
Michal Simekbdd368a2019-06-25 08:55:52 +0200458 factory-fout = <200000000>;
459 clock-frequency = <200000000>;
460 clock-output-names = "si570_ddrdimm1_clk";
Michal Simek917c5782019-03-27 20:14:19 +0100461 };
462 /* 0x50 SPD? */
463 };
464 i2c@4 { /* DDR4_DIMM2 */
465 #address-cells = <1>;
466 #size-cells = <0>;
467 reg = <4>;
468 si570_ddr_dimm2: clock-generator@60 { /* u3 */
469 #clock-cells = <0>;
470 compatible = "silabs,si570";
471 reg = <0x60>; /* 570BAB000299DG */
472 temperature-stability = <50>;
Michal Simekbdd368a2019-06-25 08:55:52 +0200473 factory-fout = <200000000>;
474 clock-frequency = <200000000>;
475 clock-output-names = "si570_ddrdimm2_clk";
Michal Simek917c5782019-03-27 20:14:19 +0100476 };
477 /* 0x50 SPD? */
478 };
479 i2c@5 { /* LPDDR4_SI570_CLK */
480 #address-cells = <1>;
481 #size-cells = <0>;
482 reg = <5>;
483 si570_lpddr4: clock-generator@60 { /* u4 */
484 #clock-cells = <0>;
485 compatible = "silabs,si570";
486 reg = <0x60>; /* 570BAB000299DG */
487 temperature-stability = <50>;
Michal Simekbdd368a2019-06-25 08:55:52 +0200488 factory-fout = <200000000>;
489 clock-frequency = <200000000>;
490 clock-output-names = "si570_lpddr4_clk";
Michal Simek917c5782019-03-27 20:14:19 +0100491 };
492 };
493 i2c@6 { /* HSDP_SI570 */
494 #address-cells = <1>;
495 #size-cells = <0>;
496 reg = <6>;
497 si570_hsdp: clock-generator@5d { /* u5 */
498 #clock-cells = <0>;
499 compatible = "silabs,si570";
500 reg = <0x5d>; /* 570JAC000900DG */
501 temperature-stability = <50>;
Michal Simekbdd368a2019-06-25 08:55:52 +0200502 factory-fout = <156250000>;
503 clock-frequency = <156250000>;
504 clock-output-names = "si570_hsdp_clk";
Michal Simek917c5782019-03-27 20:14:19 +0100505 };
506 };
507 i2c@7 { /* PCIE_CLK */
508 #address-cells = <1>;
509 #size-cells = <0>;
510 reg = <7>;
511 /* u36 0xd8 or 0xde - pcie clk buf - 9ZML1241EKILF PCIe GEN 4 CLOCK BUFFER FIXME - no driver */
512 /* u37 0xd0 DNP - pcie clocking 1 - 9FGV1006BQ505LTGI - PCIe GEN 4 CLOCK GENERATOR FIXME - no linux driver */
513 /* u38 0xca - pcie clocking 2 - 9ZML1241EKILF PCIe GEN 4 CLOCK BUFFER FIXME - no driver */
514 clock_8t49n287: clock-generator@d8 { /* u39 8T49N240 - pcie clocking 3 */
515 #clock-cells = <1>; /* author David Cater <david.cater@idt.com>*/
516 compatible = "idt,8t49n240", "idt,8t49n241"; /* FIXME no driver for 240 */
517 reg = <0xd8>;
518 /* Documentation/devicetree/bindings/clock/idt,idt8t49n24x.txt */
519 /* FIXME there input via J241 Samtec CLK1 and CLK0 from U38 - selection PIN */
520
521 };
522
523 };
524 };
525};
526
527&usb0 {
528 status = "okay";
529 xlnx,usb-polarity = <0>;
530 xlnx,usb-reset-mode = <0>;
531};
532
533&dwc3_0 {
534 status = "okay";
535 dr_mode = "peripheral";
536 snps,dis_u2_susphy_quirk;
537 snps,dis_u3_susphy_quirk;
538 maximum-speed = "super-speed";
539};
540
541&usb1 {
542 status = "okay";
543 xlnx,usb-polarity = <0>;
544 xlnx,usb-reset-mode = <0>;
545};
546
547&dwc3_1 {
548 /delete-property/ phy-names ;
549 /delete-property/ phys ;
550 dr_mode = "host";
551 maximum-speed = "high-speed";
552 snps,dis_u2_susphy_quirk ;
553 snps,dis_u3_susphy_quirk ;
554 status = "okay";
555};
556
557&xilinx_ams {
558 status = "okay";
559};
560
561&ams_ps {
562 status = "okay";
563};
564
565&ams_pl {
566 status = "okay";
567};