| Marcel Ziswiler | 5d7a95f | 2022-07-21 15:27:30 +0200 | [diff] [blame^] | 1 | // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 | /* |
| 3 | * Copyright (C) 2021 PHYTEC Messtechnik GmbH |
| 4 | * Author: Yunus Bas <y.bas@phytec.de> |
| 5 | */ |
| 6 | |
| 7 | #include <dt-bindings/gpio/gpio.h> |
| 8 | #include <dt-bindings/interrupt-controller/irq.h> |
| 9 | |
| 10 | / { |
| 11 | reg_wl_en: regulator-wl-en { |
| 12 | compatible = "regulator-fixed"; |
| 13 | regulator-name = "wlan_en"; |
| 14 | regulator-min-microvolt = <3300000>; |
| 15 | regulator-max-microvolt = <3300000>; |
| 16 | pinctrl-names = "default"; |
| 17 | pinctrl-0 = <&pinctrl_wl>; |
| 18 | gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>; |
| 19 | enable-active-high; |
| 20 | startup-delay-us = <100>; |
| 21 | status = "disabled"; |
| 22 | }; |
| 23 | }; |
| 24 | |
| 25 | &iomuxc { |
| 26 | pinctrl_bt: btgrp { |
| 27 | fsl,pins = < |
| 28 | MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x3031 /* BT ENABLE */ |
| 29 | MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x3031 /* HOST WAKEUP */ |
| 30 | MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x3031 /* DEV WAKEUP */ |
| 31 | >; |
| 32 | }; |
| 33 | |
| 34 | pinctrl_uart2_bt: uart2grp-bt { |
| 35 | fsl,pins = < |
| 36 | MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x17059 |
| 37 | MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x17059 |
| 38 | MX6UL_PAD_UART2_CTS_B__UART2_DCE_CTS 0x17059 |
| 39 | MX6UL_PAD_UART2_RTS_B__UART2_DCE_RTS 0x17059 |
| 40 | >; |
| 41 | }; |
| 42 | |
| 43 | pinctrl_usdhc2_wl: usdhc2grp-wl { |
| 44 | fsl,pins = < |
| 45 | MX6UL_PAD_LCD_DATA18__USDHC2_CMD 0x10051 |
| 46 | MX6UL_PAD_LCD_DATA19__USDHC2_CLK 0x10061 |
| 47 | MX6UL_PAD_LCD_DATA20__USDHC2_DATA0 0x10051 |
| 48 | MX6UL_PAD_LCD_DATA21__USDHC2_DATA1 0x10051 |
| 49 | MX6UL_PAD_LCD_DATA22__USDHC2_DATA2 0x10051 |
| 50 | MX6UL_PAD_LCD_DATA23__USDHC2_DATA3 0x10051 |
| 51 | >; |
| 52 | }; |
| 53 | |
| 54 | pinctrl_wl: wlgrp { |
| 55 | fsl,pins = < |
| 56 | MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x3031 /* WLAN ENABLE */ |
| 57 | >; |
| 58 | }; |
| 59 | }; |
| 60 | |
| 61 | &uart2 { |
| 62 | pinctrl-names = "default"; |
| 63 | pinctrl-0 = <&pinctrl_uart2_bt &pinctrl_bt>; |
| 64 | uart-has-rtscts; |
| 65 | status = "disabled"; |
| 66 | |
| 67 | bluetooth { |
| 68 | compatible = "brcm,bcm43438-bt"; |
| 69 | shutdown-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; |
| 70 | device-wakeup-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; |
| 71 | host-wakeup-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; |
| 72 | }; |
| 73 | }; |
| 74 | |
| 75 | &usdhc2 { |
| 76 | #address-cells = <1>; |
| 77 | #size-cells = <0>; |
| 78 | pinctrl-names = "default"; |
| 79 | pinctrl-0 = <&pinctrl_usdhc2_wl>; |
| 80 | vmmc-supply = <®_wl_en>; |
| 81 | bus-width = <4>; |
| 82 | non-removable; |
| 83 | no-1-8-v; |
| 84 | status = "disabled"; |
| 85 | |
| 86 | brmcf: wifi@1 { |
| 87 | compatible = "brcm,bcm4329-fmac"; |
| 88 | reg = <1>; |
| 89 | }; |
| 90 | }; |