blob: 785355a8e6679bde8b826308b254a9fa4e2525c3 [file] [log] [blame]
wdenkf18f47f2002-11-03 01:12:34 +00001 /*
2 * A collection of structures, addresses, and values associated with
3 * the Motorola 860T FADS board. Copied from the MBX stuff.
4 * Magnus Damm added defines for 8xxrom and extended bd_info.
5 * Helmut Buchsbaum added bitvalues for BCSRx
6 *
7 * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
8 */
9
10/*
11 * The GENIETV is using the following physical memorymap (copied from
12 * the FADS configuration):
13 *
14 * ff020000 -> ff02ffff : pcmcia
15 * ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxROM
16 * ff000000 -> ff00ffff : IMAP internal in the cpu
17 * 30000000 -> 300fffff : flash connected to CS0
18 * 00000000 -> nnnnnnnn : sdram setup by U-Boot
19 *
20 * CS pins are connected as follows:
21 *
22 * CS0 -512Kb boot flash
23 * CS1 - SDRAM #1
24 * CS2 - SDRAM #2
25 * CS3 - Flash #1
26 * CS4 - Flash #2
27 * CS5 - Lon (if present)
28 * CS6 - PCMCIA #1
29 * CS7 - PCMCIA #2
30 */
31
32/* ------------------------------------------------------------------------- */
33
34/*
35 * board/config.h - configuration options, board specific
36 */
37
38#ifndef __CONFIG_H
39#define __CONFIG_H
40
41#define CONFIG_ETHADDR 08:00:22:50:70:63 /* Ethernet address */
42#define CONFIG_ENV_OVERWRITE 1 /* Overwrite the environment */
43
44#define CFG_ALLOC_DPRAM /* Use dynamic DPRAM allocation */
45
46#define CFG_AUTOLOAD "n" /* No autoload */
47
48/*#define CONFIG_VIDEO 1 / To enable the video initialization */
49/*#define CONFIG_VIDEO_ADDR 0x00200000 */
50/*#define CONFIG_HARD_I2C 1 / I2C with hardware support */
51/*#define CONFIG_PCMCIA 1 / To enable the PCMCIA initialization */
52
53/*#define CFG_PCMCIA_IO_ADDR 0xff020000 */
54/*#define CFG_PCMCIA_IO_SIZE 0x10000 */
55/*#define CFG_PCMCIA_MEM_ADDR 0xe0000000 */
56/*#define CFG_PCMCIA_MEM_SIZE 0x10000 */
57
58/* Video related */
59
60/*#define CONFIG_VIDEO_LOGO 1 / Show the logo */
61/*#define CONFIG_VIDEO_ENCODER_AD7177 1 / Enable this encoder */
62/*#define CONFIG_VIDEO_ENCODER_AD7177_ADDR 0xF4 / ALSB to ground */
63
64/* Wireless 56Khz 4PPM keyboard on SMCx */
65
wdenk682011f2003-06-03 23:54:09 +000066/*#define CONFIG_KEYBOARD 0 */
wdenkf18f47f2002-11-03 01:12:34 +000067/*#define CONFIG_WL_4PPM_KEYBOARD_SMC 0 / SMC to use (0 indexed) */
68
69/*
70 * High Level Configuration Options
71 * (easy to change)
72 */
73#include <mpc8xx_irq.h>
74
75#define CONFIG_GENIETV 1
76#define CONFIG_MPC823 1
77
78#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
79#undef CONFIG_8xx_CONS_SMC2
80#undef CONFIG_8xx_CONS_NONE
81#define CONFIG_BAUDRATE 9600
82
83#define MPC8XX_FACT 12 /* Multiply by 12 */
84#define MPC8XX_XIN 5000000 /* 4 MHz clock */
85
86#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
87#define CFG_PLPRCR_MF ((MPC8XX_FACT-1) << 20)
88#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ /* Force it - dont measure it */
89
90#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
91
92#if 1
93#define CONFIG_BOOTDELAY 1 /* autoboot after 2 seconds */
94#define CONFIG_LOADS_ECHO 0 /* Dont echoes received characters */
95#define CONFIG_BOOTARGS ""
96#define CONFIG_BOOTCOMMAND \
97"bootp; tftp; " \
98"setenv bootargs console=tty0 console=ttyS0 " \
Wolfgang Denkfe126d82005-11-20 21:40:11 +010099"root=/dev/nfs nfsroot=${serverip}:${rootpath} " \
100"ip=${ipaddr}:${serverip}:${gatewayip}:${subnetmask}:${hostname}:eth0:off ;" \
wdenkf18f47f2002-11-03 01:12:34 +0000101"bootm "
102#else
103#define CONFIG_BOOTDELAY 0 /* autoboot disabled */
104#endif
105
106#undef CONFIG_WATCHDOG /* watchdog disabled */
107
Jon Loeliger60a08762007-07-07 21:04:26 -0500108
109/*
Jon Loeliger11799432007-07-10 09:02:57 -0500110 * BOOTP options
111 */
112#define CONFIG_BOOTP_BOOTFILESIZE
113#define CONFIG_BOOTP_BOOTPATH
114#define CONFIG_BOOTP_GATEWAY
115#define CONFIG_BOOTP_HOSTNAME
116
117
118/*
Jon Loeliger60a08762007-07-07 21:04:26 -0500119 * Command line configuration.
120 */
121#include <config_cmd_default.h>
122
wdenkf18f47f2002-11-03 01:12:34 +0000123
124/*
125 * Miscellaneous configurable options
126 */
127#define CFG_LONGHELP /* undef to save memory */
128#define CFG_PROMPT ":>" /* Monitor Command Prompt */
Jon Loeliger60a08762007-07-07 21:04:26 -0500129#if defined(CONFIG_CMD_KGDB)
wdenkf18f47f2002-11-03 01:12:34 +0000130#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
131#else
132#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
133#endif
134#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
135#define CFG_MAXARGS 8 /* max number of command args */
136#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
137
138#define CFG_MEMTEST_START 0x00004000 /* memtest works on */
139#define CFG_MEMTEST_END 0x00800000 /* 0 ... 8 MB in DRAM */
140
141#define CFG_LOAD_ADDR 0x00100000 /* default load address */
142
143#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
144
145#define CFG_BAUDRATE_TABLE { 4800, 9600, 19200, 38400, 57600, 115200 }
146
147/*
148 * Low Level Configuration Settings
149 * (address mappings, register initial values, etc.)
150 * You should know what you are doing if you make changes here.
151 */
152/*-----------------------------------------------------------------------
153 * Internal Memory Mapped Register
154 */
155#define CFG_IMMR 0xFF000000
156#define CFG_IMMR_SIZE ((uint)(64 * 1024))
157
158/*-----------------------------------------------------------------------
159 * Definitions for initial stack pointer and data area (in DPRAM)
160 */
161#define CFG_INIT_RAM_ADDR CFG_IMMR
162#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
163#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
164#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
165#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
166
167/*-----------------------------------------------------------------------
168 * Start addresses for the final memory configuration
169 * (Set up by the startup code)
170 * Please note that CFG_SDRAM_BASE _must_ start at 0
171 * Also NOTE that it doesn't mean SDRAM - it means MEMORY.
172 */
173#define CFG_SDRAM_BASE 0x00000000
174#define CFG_FLASH_BASE 0x02800000
175#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
176#if 0
177#define CFG_MONITOR_LEN (256 << 10) /* Reserve 128 kB for Monitor */
178#else
179#define CFG_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
180#endif
181#define CFG_MONITOR_BASE CFG_FLASH_BASE
182#define CFG_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */
183
184/*
185 * For booting Linux, the board info and command line data
186 * have to be in the first 8 MB of memory, since this is
187 * the maximum mapped by the Linux kernel during initialization.
188 */
189#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
190/*-----------------------------------------------------------------------
191 * FLASH organization
192 */
193#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
194#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
195
196#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
197#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
198
199#define CFG_ENV_IS_IN_FLASH 1
200#define CFG_ENV_OFFSET 0x10000 /* Offset of Environment Sector */
201#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector (64k)*/
202
203/* values according to the manual */
204
205/*-----------------------------------------------------------------------
206 * Cache Configuration
207 */
208#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
Jon Loeliger60a08762007-07-07 21:04:26 -0500209#if defined(CONFIG_CMD_KGDB)
wdenkf18f47f2002-11-03 01:12:34 +0000210#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
211#endif
212
213/*-----------------------------------------------------------------------
214 * SYPCR - System Protection Control 11-9
215 * SYPCR can only be written once after reset!
216 *-----------------------------------------------------------------------
217 * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
218 */
219#if defined(CONFIG_WATCHDOG)
220#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
221 SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
222#else
223#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
224#endif
225
226/*-----------------------------------------------------------------------
227 * SIUMCR - SIU Module Configuration 11-6
228 *-----------------------------------------------------------------------
229 * PCMCIA config., multi-function pin tri-state
230 *
231#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
232 */
233#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC10)
234
235/*-----------------------------------------------------------------------
236 * TBSCR - Time Base Status and Control 11-26
237 *-----------------------------------------------------------------------
238 * Clear Reference Interrupt Status, Timebase freezing enabled
239 */
240#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
241
242/*-----------------------------------------------------------------------
243 * PISCR - Periodic Interrupt Status and Control 11-31
244 *-----------------------------------------------------------------------
245 * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
246 */
247#define CFG_PISCR (PISCR_PS | PISCR_PITF)
248
249/*-----------------------------------------------------------------------
250 * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
251 *-----------------------------------------------------------------------
252 * Reset PLL lock status sticky bit, timer expired status bit and timer *
253 * interrupt status bit - leave PLL multiplication factor unchanged !
254 *
255 * #define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
256 */
257#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | CFG_PLPRCR_MF)
258
259/*-----------------------------------------------------------------------
260 * SCCR - System Clock and reset Control Register 15-27
261 *-----------------------------------------------------------------------
262 * Set clock output, timebase and RTC source and divider,
263 * power management and some other internal clocks
264 */
265#define SCCR_MASK SCCR_EBDF11
266#define CFG_SCCR (SCCR_TBS | \
267 SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
268 SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
269 SCCR_DFALCD00)
270
271/*-----------------------------------------------------------------------
272 *
273 *-----------------------------------------------------------------------
274 *
275 */
276#define CFG_DER 0
277
278/* Because of the way the 860 starts up and assigns CS0 the
279* entire address space, we have to set the memory controller
280* differently. Normally, you write the option register
281* first, and then enable the chip select by writing the
282* base register. For CS0, you must write the base register
283* first, followed by the option register.
284*/
285
286/*
287 * Init Memory Controller:
288 *
289 * BR0 and OR0(FLASH)
290 */
291
292#define FLASH_BASE0_PRELIM 0x02800000 /* FLASH bank #0 */
293
294#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
295#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask (512Kb) */
296
297/* FLASH timing */
298#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \
299 OR_SCY_15_CLK | OR_TRLX )
300
301/*#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) */
302#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 0xfff80ff4 */
303#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_8) /* 0x02800401 */
304
305/*
306 * BR1/2 and OR1/2 (SDRAM)
307*/
308
309#define CFG_OR_TIMING_SDRAM 0x00000A00
310
311#define SDRAM_MAX_SIZE 0x04000000 /* 64Mb bank */
312#define SDRAM_BASE1_PRELIM 0x00000000 /* First bank */
313#define SDRAM_BASE2_PRELIM 0x10000000 /* Second bank */
314
315/*
316 * Memory Periodic Timer Prescaler
317 */
318
319/* periodic timer for refresh */
320#define CFG_MBMR_PTB 0x5d /* start with divider for 100 MHz */
321
322/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
323#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
324#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32
325/*
326 * MBMR settings for SDRAM
327 */
328
329/* 8 column SDRAM */
330#define CFG_MBMR_8COL ((CFG_MBMR_PTB << MAMR_PTA_SHIFT) | MAMR_PTAE | \
331 MAMR_G0CLA_A11 | MAMR_RLFA_1X | MAMR_WLFA_1X \
332 | MAMR_TLFA_4X) /* 0x5d802114 */
333
334/*
335 * Internal Definitions
336 *
337 * Boot Flags
338 */
339#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
340#define BOOTFLAG_WARM 0x02 /* Software reboot */
341
342/* values according to the manual */
343
344#define CONFIG_DRAM_50MHZ 1
345#define CONFIG_SDRAM_50MHZ
346
347/* We don't use the 8259.
348*/
349#define NR_8259_INTS 0
350
351/* Machine type
352*/
353#define _MACH_8xx (_MACH_fads)
354
355/*
356 * MPC8xx CPM Options
357 */
358#define CONFIG_SCC_ENET 1
359
360#define CONFIG_DISK_SPINUP_TIME 1000000
361
362/* PCMCIA configuration */
363
364#define PCMCIA_MAX_SLOTS 1
365#define PCMCIA_SLOT_B 1
366
367#endif /* __CONFIG_H */