board/engicam/common/spl.c

/*
 * Copyright (C) 2016 Amarula Solutions B.V.
 * Copyright (C) 2016 Engicam S.r.l.
 * Author: Jagan Teki <jagan@amarulasolutions.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <spl.h>

#include <asm/io.h>
#include <asm/gpio.h>
#include <linux/sizes.h>

#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-ddr.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>

#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/video.h>

DECLARE_GLOBAL_DATA_PTR;

#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |             \
        PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
        PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

static iomux_v3_cfg_t const uart_pads[] = {
#ifdef CONFIG_MX6QDL
        IOMUX_PADS(PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
        IOMUX_PADS(PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
#elif CONFIG_MX6UL
	IOMUX_PADS(PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL)),
	IOMUX_PADS(PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL)),
#endif
};

#ifdef CONFIG_SPL_OS_BOOT
int spl_start_uboot(void)
{
	/* break into full u-boot on 'c' */
	if (serial_tstc() && serial_getc() == 'c')
		return 1;

	return 0;
}
#endif

#ifdef CONFIG_MX6QDL
/*
 * Driving strength:
 *   0x30 == 40 Ohm
 *   0x28 == 48 Ohm
 */
#define IMX6DQ_DRIVE_STRENGTH		0x30
#define IMX6SDL_DRIVE_STRENGTH		0x28

/* configure MX6Q/DUAL mmdc DDR io registers */
static struct mx6dq_iomux_ddr_regs mx6dq_ddr_ioregs = {
	.dram_sdqs0 = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdqs1 = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdqs2 = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdqs3 = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdqs4 = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdqs5 = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdqs6 = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdqs7 = IMX6DQ_DRIVE_STRENGTH,
	.dram_dqm0 = IMX6DQ_DRIVE_STRENGTH,
	.dram_dqm1 = IMX6DQ_DRIVE_STRENGTH,
	.dram_dqm2 = IMX6DQ_DRIVE_STRENGTH,
	.dram_dqm3 = IMX6DQ_DRIVE_STRENGTH,
	.dram_dqm4 = IMX6DQ_DRIVE_STRENGTH,
	.dram_dqm5 = IMX6DQ_DRIVE_STRENGTH,
	.dram_dqm6 = IMX6DQ_DRIVE_STRENGTH,
	.dram_dqm7 = IMX6DQ_DRIVE_STRENGTH,
	.dram_cas = IMX6DQ_DRIVE_STRENGTH,
	.dram_ras = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdclk_0 = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdclk_1 = IMX6DQ_DRIVE_STRENGTH,
	.dram_reset = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdcke0 = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdcke1 = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdba2 = 0x00000000,
	.dram_sdodt0 = IMX6DQ_DRIVE_STRENGTH,
	.dram_sdodt1 = IMX6DQ_DRIVE_STRENGTH,
};

/* configure MX6Q/DUAL mmdc GRP io registers */
static struct mx6dq_iomux_grp_regs mx6dq_grp_ioregs = {
	.grp_b0ds = IMX6DQ_DRIVE_STRENGTH,
	.grp_b1ds = IMX6DQ_DRIVE_STRENGTH,
	.grp_b2ds = IMX6DQ_DRIVE_STRENGTH,
	.grp_b3ds = IMX6DQ_DRIVE_STRENGTH,
	.grp_b4ds = IMX6DQ_DRIVE_STRENGTH,
	.grp_b5ds = IMX6DQ_DRIVE_STRENGTH,
	.grp_b6ds = IMX6DQ_DRIVE_STRENGTH,
	.grp_b7ds = IMX6DQ_DRIVE_STRENGTH,
	.grp_addds = IMX6DQ_DRIVE_STRENGTH,
	.grp_ddrmode_ctl = 0x00020000,
	.grp_ddrpke = 0x00000000,
	.grp_ddrmode = 0x00020000,
	.grp_ctlds = IMX6DQ_DRIVE_STRENGTH,
	.grp_ddr_type = 0x000c0000,
};

/* configure MX6SOLO/DUALLITE mmdc DDR io registers */
struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = {
	.dram_sdclk_0 = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdclk_1 = IMX6SDL_DRIVE_STRENGTH,
	.dram_cas = IMX6SDL_DRIVE_STRENGTH,
	.dram_ras = IMX6SDL_DRIVE_STRENGTH,
	.dram_reset = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdcke0 = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdcke1 = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdba2 = 0x00000000,
	.dram_sdodt0 = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdodt1 = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdqs0 = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdqs1 = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdqs2 = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdqs3 = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdqs4 = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdqs5 = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdqs6 = IMX6SDL_DRIVE_STRENGTH,
	.dram_sdqs7 = IMX6SDL_DRIVE_STRENGTH,
	.dram_dqm0 = IMX6SDL_DRIVE_STRENGTH,
	.dram_dqm1 = IMX6SDL_DRIVE_STRENGTH,
	.dram_dqm2 = IMX6SDL_DRIVE_STRENGTH,
	.dram_dqm3 = IMX6SDL_DRIVE_STRENGTH,
	.dram_dqm4 = IMX6SDL_DRIVE_STRENGTH,
	.dram_dqm5 = IMX6SDL_DRIVE_STRENGTH,
	.dram_dqm6 = IMX6SDL_DRIVE_STRENGTH,
	.dram_dqm7 = IMX6SDL_DRIVE_STRENGTH,
};

/* configure MX6SOLO/DUALLITE mmdc GRP io registers */
struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
	.grp_ddr_type = 0x000c0000,
	.grp_ddrmode_ctl = 0x00020000,
	.grp_ddrpke = 0x00000000,
	.grp_addds = IMX6SDL_DRIVE_STRENGTH,
	.grp_ctlds = IMX6SDL_DRIVE_STRENGTH,
	.grp_ddrmode = 0x00020000,
	.grp_b0ds = IMX6SDL_DRIVE_STRENGTH,
	.grp_b1ds = IMX6SDL_DRIVE_STRENGTH,
	.grp_b2ds = IMX6SDL_DRIVE_STRENGTH,
	.grp_b3ds = IMX6SDL_DRIVE_STRENGTH,
	.grp_b4ds = IMX6SDL_DRIVE_STRENGTH,
	.grp_b5ds = IMX6SDL_DRIVE_STRENGTH,
	.grp_b6ds = IMX6SDL_DRIVE_STRENGTH,
	.grp_b7ds = IMX6SDL_DRIVE_STRENGTH,
};

/* mt41j256 */
static struct mx6_ddr3_cfg mt41j256 = {
	.mem_speed = 1066,
	.density = 2,
	.width = 16,
	.banks = 8,
	.rowaddr = 13,
	.coladdr = 10,
	.pagesz = 2,
	.trcd = 1375,
	.trcmin = 4875,
	.trasmin = 3500,
	.SRT = 0,
};

static struct mx6_mmdc_calibration mx6dq_mmdc_calib = {
	.p0_mpwldectrl0 = 0x000E0009,
	.p0_mpwldectrl1 = 0x0018000E,
	.p1_mpwldectrl0 = 0x00000007,
	.p1_mpwldectrl1 = 0x00000000,
	.p0_mpdgctrl0 = 0x43280334,
	.p0_mpdgctrl1 = 0x031C0314,
	.p1_mpdgctrl0 = 0x4318031C,
	.p1_mpdgctrl1 = 0x030C0258,
	.p0_mprddlctl = 0x3E343A40,
	.p1_mprddlctl = 0x383C3844,
	.p0_mpwrdlctl = 0x40404440,
	.p1_mpwrdlctl = 0x4C3E4446,
};

/* DDR 64bit */
static struct mx6_ddr_sysinfo mem_q = {
	.ddr_type	= DDR_TYPE_DDR3,
	.dsize		= 2,
	.cs1_mirror	= 0,
	/* config for full 4GB range so that get_mem_size() works */
	.cs_density	= 32,
	.ncs		= 1,
	.bi_on		= 1,
	.rtt_nom	= 2,
	.rtt_wr		= 2,
	.ralat		= 5,
	.walat		= 0,
	.mif3_mode	= 3,
	.rst_to_cke	= 0x23,
	.sde_to_rst	= 0x10,
};

static struct mx6_mmdc_calibration mx6dl_mmdc_calib = {
	.p0_mpwldectrl0 = 0x001F0024,
	.p0_mpwldectrl1 = 0x00110018,
	.p1_mpwldectrl0 = 0x001F0024,
	.p1_mpwldectrl1 = 0x00110018,
	.p0_mpdgctrl0 = 0x4230022C,
	.p0_mpdgctrl1 = 0x02180220,
	.p1_mpdgctrl0 = 0x42440248,
	.p1_mpdgctrl1 = 0x02300238,
	.p0_mprddlctl = 0x44444A48,
	.p1_mprddlctl = 0x46484A42,
	.p0_mpwrdlctl = 0x38383234,
	.p1_mpwrdlctl = 0x3C34362E,
};

/* DDR 64bit 1GB */
static struct mx6_ddr_sysinfo mem_dl = {
	.dsize		= 2,
	.cs1_mirror	= 0,
	/* config for full 4GB range so that get_mem_size() works */
	.cs_density	= 32,
	.ncs		= 1,
	.bi_on		= 1,
	.rtt_nom	= 1,
	.rtt_wr		= 1,
	.ralat		= 5,
	.walat		= 0,
	.mif3_mode	= 3,
	.rst_to_cke	= 0x23,
	.sde_to_rst	= 0x10,
};

/* DDR 32bit 512MB */
static struct mx6_ddr_sysinfo mem_s = {
	.dsize		= 1,
	.cs1_mirror	= 0,
	/* config for full 4GB range so that get_mem_size() works */
	.cs_density	= 32,
	.ncs		= 1,
	.bi_on		= 1,
	.rtt_nom	= 1,
	.rtt_wr		= 1,
	.ralat		= 5,
	.walat		= 0,
	.mif3_mode	= 3,
	.rst_to_cke	= 0x23,
	.sde_to_rst	= 0x10,
};
#endif /* CONFIG_MX6QDL */

#ifdef CONFIG_MX6UL
static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
	.grp_addds = 0x00000030,
	.grp_ddrmode_ctl = 0x00020000,
	.grp_b0ds = 0x00000030,
	.grp_ctlds = 0x00000030,
	.grp_b1ds = 0x00000030,
	.grp_ddrpke = 0x00000000,
	.grp_ddrmode = 0x00020000,
	.grp_ddr_type = 0x000c0000,
};

static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
	.dram_dqm0 = 0x00000030,
	.dram_dqm1 = 0x00000030,
	.dram_ras = 0x00000030,
	.dram_cas = 0x00000030,
	.dram_odt0 = 0x00000030,
	.dram_odt1 = 0x00000030,
	.dram_sdba2 = 0x00000000,
	.dram_sdclk_0 = 0x00000008,
	.dram_sdqs0 = 0x00000038,
	.dram_sdqs1 = 0x00000030,
	.dram_reset = 0x00000030,
};

static struct mx6_mmdc_calibration mx6_mmcd_calib = {
	.p0_mpwldectrl0 = 0x00070007,
	.p0_mpdgctrl0 = 0x41490145,
	.p0_mprddlctl = 0x40404546,
	.p0_mpwrdlctl = 0x4040524D,
};

struct mx6_ddr_sysinfo ddr_sysinfo = {
	.dsize = 0,
	.cs_density = 20,
	.ncs = 1,
	.cs1_mirror = 0,
	.rtt_wr = 2,
	.rtt_nom = 1,		/* RTT_Nom = RZQ/2 */
	.walat = 1,		/* Write additional latency */
	.ralat = 5,		/* Read additional latency */
	.mif3_mode = 3,		/* Command prediction working mode */
	.bi_on = 1,		/* Bank interleaving enabled */
	.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
	.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
	.ddr_type = DDR_TYPE_DDR3,
};

static struct mx6_ddr3_cfg mem_ddr = {
	.mem_speed = 800,
	.density = 4,
	.width = 16,
	.banks = 8,
#ifdef TARGET_MX6UL_ISIOT
	.rowaddr = 15,
#else
	.rowaddr = 13,
#endif
	.coladdr = 10,
	.pagesz = 2,
	.trcd = 1375,
	.trcmin = 4875,
	.trasmin = 3500,
};
#endif /* CONFIG_MX6UL */

static void ccgr_init(void)
{
	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;

#ifdef CONFIG_MX6QDL
	writel(0x00003F3F, &ccm->CCGR0);
	writel(0x0030FC00, &ccm->CCGR1);
	writel(0x000FC000, &ccm->CCGR2);
	writel(0x3F300000, &ccm->CCGR3);
	writel(0xFF00F300, &ccm->CCGR4);
	writel(0x0F0000C3, &ccm->CCGR5);
	writel(0x000003CC, &ccm->CCGR6);
#elif CONFIG_MX6UL
	writel(0x00c03f3f, &ccm->CCGR0);
	writel(0xfcffff00, &ccm->CCGR1);
	writel(0x0cffffcc, &ccm->CCGR2);
	writel(0x3f3c3030, &ccm->CCGR3);
	writel(0xff00fffc, &ccm->CCGR4);
	writel(0x033f30ff, &ccm->CCGR5);
	writel(0x00c00fff, &ccm->CCGR6);
#endif
}

static void spl_dram_init(void)
{
#ifdef CONFIG_MX6QDL
	if (is_mx6solo()) {
		mx6sdl_dram_iocfg(32, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs);
		mx6_dram_cfg(&mem_s, &mx6dl_mmdc_calib, &mt41j256);
	} else if (is_mx6dl()) {
		mx6sdl_dram_iocfg(64, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs);
		mx6_dram_cfg(&mem_dl, &mx6dl_mmdc_calib, &mt41j256);
	} else if (is_mx6dq()) {
		mx6dq_dram_iocfg(64, &mx6dq_ddr_ioregs, &mx6dq_grp_ioregs);
		mx6_dram_cfg(&mem_q, &mx6dq_mmdc_calib, &mt41j256);
	}
#elif CONFIG_MX6UL
	mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
	mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
#endif

	udelay(100);
}

void board_init_f(ulong dummy)
{
	ccgr_init();

	/* setup AIPS and disable watchdog */
	arch_cpu_init();

	gpr_init();

	/* iomux */
	SETUP_IOMUX_PADS(uart_pads);

	/* setup GP timer */
	timer_init();

	/* UART clocks enabled and gd valid - init serial console */
	preloader_console_init();

	/* DDR initialization */
	spl_dram_init();

	/* Clear the BSS. */
	memset(__bss_start, 0, __bss_end - __bss_start);

	/* load/boot image from boot device */
	board_init_r(NULL, 0);
}