blob: adce3f6a0a9582a6821376f25cd0952f8298def8 [file] [log] [blame]
Paul Kocialkowski68f7c5d2015-08-04 17:04:05 +02001menuconfig USB
2 bool "USB support"
Masahiro Yamada6e7e9292014-11-07 18:48:31 +09003 ---help---
4 Universal Serial Bus (USB) is a specification for a serial bus
5 subsystem which offers higher speeds and more features than the
6 traditional PC serial port. The bus supplies power to peripherals
7 and allows for hot swapping. Up to 127 USB peripherals can be
8 connected to a single USB host in a tree structure.
9
10 The USB host is the root of the tree, the peripherals are the
11 leaves and the inner nodes are special USB devices called hubs.
12 Most PCs now have USB host ports, used to connect peripherals
13 such as scanners, keyboards, mice, modems, cameras, disks,
14 flash memory, network links, and printers to the PC.
15
Paul Kocialkowski68f7c5d2015-08-04 17:04:05 +020016 Say Y here if your device has an USB port, either host, peripheral or
17 dual-role.
18
19 For an USB host port, you then need to say Y to at least one of the
Masahiro Yamada6e7e9292014-11-07 18:48:31 +090020 Host Controller Driver (HCD) options below. Choose a USB 1.1
21 controller, such as "UHCI HCD support" or "OHCI HCD support",
22 and "EHCI HCD (USB 2.0) support" except for older systems that
23 do not have USB 2.0 support. It doesn't normally hurt to select
24 them all if you are not certain.
25
26 If your system has a device-side USB port, used in the peripheral
27 side of the USB protocol, see the "USB Gadget" framework instead.
28
29 After choosing your HCD, then select drivers for the USB peripherals
30 you'll be using. You may want to check out the information provided
31 in <file:Documentation/usb/> and especially the links given in
32 <file:Documentation/usb/usb-help.txt>.
33
34if USB
35
Simon Glassde312132015-03-25 12:21:59 -060036config DM_USB
37 bool "Enable driver model for USB"
38 depends on USB && DM
39 help
40 Enable driver model for USB. The USB interface is then implemented
41 by the USB uclass. Multiple USB controllers of different types
42 (XHCI, EHCI) can be attached and used. The 'usb' command works as
43 normal. OCHI is not supported at present.
44
45 Much of the code is shared but with this option enabled the USB
46 uclass takes care of device enumeration. USB devices can be
Simon Glassabb59cf2015-07-06 16:47:51 -060047 declared with the U_BOOT_USB_DEVICE() macro and will be
48 automatically probed when found on the bus.
Simon Glassde312132015-03-25 12:21:59 -060049
Masahiro Yamada6e7e9292014-11-07 18:48:31 +090050source "drivers/usb/host/Kconfig"
51
Simon Glass019808f2015-03-25 12:22:37 -060052source "drivers/usb/emul/Kconfig"
53
Paul Kocialkowski68f7c5d2015-08-04 17:04:05 +020054comment "USB peripherals"
55
Masahiro Yamada6e7e9292014-11-07 18:48:31 +090056config USB_STORAGE
57 bool "USB Mass Storage support"
58 ---help---
59 Say Y here if you want to connect USB mass storage devices to your
60 board's USB port.
61
Nikita Kiryanovb2f2eea2015-07-23 17:19:36 +030062config USB_KEYBOARD
63 bool "USB Keyboard support"
64 ---help---
65 Say Y here if you want to use a USB keyboard for U-Boot command line
66 input.
67
68if USB_KEYBOARD
69
70choice
71 prompt "USB keyboard polling"
72 optional
73 ---help---
74 Enable a polling mechanism for USB keyboard.
75
76 config SYS_USB_EVENT_POLL
77 bool "Interrupt polling"
78
79 config SYS_USB_EVENT_POLL_VIA_INT_QUEUE
80 bool "Poll via interrupt queue"
81
82 config SYS_USB_EVENT_POLL_VIA_CONTROL_EP
83 bool "Poll via control EP"
84
85endchoice
86
Masahiro Yamada6e7e9292014-11-07 18:48:31 +090087endif
Nikita Kiryanovb2f2eea2015-07-23 17:19:36 +030088
Masahiro Yamadaed363232014-09-16 16:32:58 +090089endif