blob: 6f54f50a70b0f8e0b0c81da5963e319858b6ddcd [file] [log] [blame]
Tom Rini53633a82024-02-29 12:33:36 -05001// SPDX-License-Identifier: BSD-3-Clause
2/*
Tom Rini6bb92fc2024-05-20 09:54:58 -06003 * Copyright (c) 2022-2024 Jianhua Lu <lujianhua000@gmail.com>
Tom Rini53633a82024-02-29 12:33:36 -05004 */
5
6#include <dt-bindings/arm/qcom,ids.h>
7#include <dt-bindings/phy/phy.h>
8#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
Tom Rini93743d22024-04-01 09:08:13 -04009#include <dt-bindings/usb/pd.h>
Tom Rini53633a82024-02-29 12:33:36 -050010#include "sm8250.dtsi"
11#include "pm8150.dtsi"
12#include "pm8150b.dtsi"
13#include "pm8150l.dtsi"
14#include "pm8009.dtsi"
15
16/*
17 * Delete following upstream (sm8250.dtsi) reserved
18 * memory mappings which are different on this device.
19 */
20/delete-node/ &adsp_mem;
21/delete-node/ &cdsp_secure_heap;
22/delete-node/ &slpi_mem;
23/delete-node/ &spss_mem;
24/delete-node/ &xbl_aop_mem;
25
26/ {
Tom Rini93743d22024-04-01 09:08:13 -040027 chassis-type = "tablet";
Tom Rini53633a82024-02-29 12:33:36 -050028
29 /* required for bootloader to select correct board */
30 qcom,msm-id = <QCOM_ID_SM8250 0x20001>; /* SM8250 v2.1 */
31 qcom,board-id = <0x10008 0>;
32
33 chosen {
34 #address-cells = <2>;
35 #size-cells = <2>;
36 ranges;
37
38 framebuffer: framebuffer@9c000000 {
39 compatible = "simple-framebuffer";
40 reg = <0x0 0x9c000000 0x0 0x2300000>;
41 width = <1600>;
42 height = <2560>;
43 stride = <(1600 * 4)>;
44 format = "a8r8g8b8";
45 };
46 };
47
48 battery_l: battery-l {
49 compatible = "simple-battery";
50 voltage-min-design-microvolt = <3870000>;
51 energy-full-design-microwatt-hours = <16600000>;
52 charge-full-design-microamp-hours = <4300000>;
53 };
54
55 battery_r: battery-r {
56 compatible = "simple-battery";
57 voltage-min-design-microvolt = <3870000>;
58 energy-full-design-microwatt-hours = <16600000>;
59 charge-full-design-microamp-hours = <4300000>;
60 };
61
62 bl_vddpos_5p5: bl-vddpos-regulator {
63 compatible = "regulator-fixed";
64 regulator-name = "bl_vddpos_5p5";
65 regulator-min-microvolt = <5500000>;
66 regulator-max-microvolt = <5500000>;
67 regulator-enable-ramp-delay = <233>;
68 gpio = <&tlmm 130 GPIO_ACTIVE_HIGH>;
69 enable-active-high;
70 regulator-boot-on;
71 };
72
73 bl_vddneg_5p5: bl-vddneg-regulator {
74 compatible = "regulator-fixed";
75 regulator-name = "bl_vddneg_5p5";
76 regulator-min-microvolt = <5500000>;
77 regulator-max-microvolt = <5500000>;
78 regulator-enable-ramp-delay = <233>;
79 gpio = <&tlmm 131 GPIO_ACTIVE_HIGH>;
80 enable-active-high;
81 regulator-boot-on;
82 };
83
84 gpio_keys: gpio-keys {
85 compatible = "gpio-keys";
86
87 pinctrl-names = "default";
88 pinctrl-0 = <&vol_up_n>;
89
90 key-vol-up {
91 label = "Volume Up";
92 gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
93 linux,code = <KEY_VOLUMEUP>;
94 debounce-interval = <15>;
95 linux,can-disable;
96 wakeup-source;
97 };
98 };
99
100 vph_pwr: vph-pwr-regulator {
101 compatible = "regulator-fixed";
102 regulator-name = "vph_pwr";
103 regulator-min-microvolt = <3700000>;
104 regulator-max-microvolt = <3700000>;
105 };
106
107 /* S6c is really ebi.lvl but it's there for supply map completeness sake. */
108 vreg_s6c_0p88: smpc6-regulator {
109 compatible = "regulator-fixed";
110 regulator-name = "vreg_s6c_0p88";
111 regulator-min-microvolt = <880000>;
112 regulator-max-microvolt = <880000>;
113 regulator-always-on;
114 vin-supply = <&vph_pwr>;
115 };
116
117 reserved-memory {
Tom Rini93743d22024-04-01 09:08:13 -0400118 xbl_aop_mem: xbl-aop@80600000 {
Tom Rini53633a82024-02-29 12:33:36 -0500119 reg = <0x0 0x80600000 0x0 0x260000>;
120 no-map;
121 };
122
123 slpi_mem: slpi@88c00000 {
124 reg = <0x0 0x88c00000 0x0 0x2f00000>;
125 no-map;
126 };
127
128 adsp_mem: adsp@8bb00000 {
129 reg = <0x0 0x8bb00000 0x0 0x2500000>;
130 no-map;
131 };
132
133 spss_mem: spss@8e000000 {
134 reg = <0x0 0x8e000000 0x0 0x100000>;
135 no-map;
136 };
137
138 cdsp_secure_heap: cdsp-secure-heap@8e100000 {
139 reg = <0x0 0x8e100000 0x0 0x4600000>;
140 no-map;
141 };
142
143 cont_splash_mem: cont-splash@9c000000 {
144 reg = <0x0 0x9c000000 0x0 0x2300000>;
145 no-map;
146 };
147
148 ramoops@b0000000 {
149 compatible = "ramoops";
150 reg = <0x0 0xb0000000 0x0 0x400000>;
151 record-size = <0x1000>;
152 console-size = <0x200000>;
153 ecc-size = <16>;
154 no-map;
155 };
156 };
157};
158
159&adsp {
160 firmware-name = "qcom/sm8250/xiaomi/elish/adsp.mbn";
161 status = "okay";
162};
163
164&apps_rsc {
165 regulators-0 {
166 compatible = "qcom,pm8150-rpmh-regulators";
167 qcom,pmic-id = "a";
168
169 vdd-s1-supply = <&vph_pwr>;
170 vdd-s2-supply = <&vph_pwr>;
171 vdd-s3-supply = <&vph_pwr>;
172 vdd-s4-supply = <&vph_pwr>;
173 vdd-s5-supply = <&vph_pwr>;
174 vdd-s6-supply = <&vph_pwr>;
175 vdd-s7-supply = <&vph_pwr>;
176 vdd-s8-supply = <&vph_pwr>;
177 vdd-s9-supply = <&vph_pwr>;
178 vdd-s10-supply = <&vph_pwr>;
179 vdd-l1-l8-l11-supply = <&vreg_s6c_0p88>;
180 vdd-l2-l10-supply = <&vreg_bob>;
181 vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p95>;
182 vdd-l6-l9-supply = <&vreg_s8c_1p35>;
183 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>;
184 vdd-l13-l16-l17-supply = <&vreg_bob>;
185
186 /* (S1+S2+S3) - cx.lvl (ARC) */
187
188 vreg_s4a_1p8: smps4 {
189 regulator-name = "vreg_s4a_1p8";
190 regulator-min-microvolt = <1800000>;
191 regulator-max-microvolt = <1920000>;
192 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
193 regulator-allow-set-load;
194 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
195 RPMH_REGULATOR_MODE_HPM>;
196 };
197
198 vreg_s5a_1p9: smps5 {
199 regulator-name = "vreg_s5a_1p9";
200 regulator-min-microvolt = <1900000>;
201 regulator-max-microvolt = <2040000>;
202 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
203 };
204
205 vreg_s6a_0p95: smps6 {
206 regulator-name = "vreg_s6a_0p95";
207 regulator-min-microvolt = <950000>;
208 regulator-max-microvolt = <1128000>;
209 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
210 };
211
212 vreg_l2a_3p1: ldo2 {
213 regulator-name = "vreg_l2a_3p1";
214 regulator-min-microvolt = <3072000>;
215 regulator-max-microvolt = <3072000>;
216 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
217 };
218
219 vreg_l3a_0p9: ldo3 {
220 regulator-name = "vreg_l3a_0p9";
221 regulator-min-microvolt = <928000>;
222 regulator-max-microvolt = <932000>;
223 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
224 };
225
226 /* L4 - lmx.lvl (ARC) */
227
228 vreg_l5a_0p88: ldo5 {
229 regulator-name = "vreg_l5a_0p88";
230 regulator-min-microvolt = <880000>;
231 regulator-max-microvolt = <880000>;
232 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
233 };
234
235 vreg_l6a_1p2: ldo6 {
236 regulator-name = "vreg_l6a_1p2";
237 regulator-min-microvolt = <1200000>;
238 regulator-max-microvolt = <1200000>;
239 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
240 regulator-allow-set-load;
241 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
242 RPMH_REGULATOR_MODE_HPM>;
243 };
244
245 /* L7 is unused. */
246
247 vreg_l9a_1p2: ldo9 {
248 regulator-name = "vreg_l9a_1p2";
249 regulator-min-microvolt = <1200000>;
250 regulator-max-microvolt = <1200000>;
251 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
252 };
253
254 /* L10 is unused, L11 - lcx.lvl (ARC) */
255
256 vreg_l12a_1p8: ldo12 {
257 regulator-name = "vreg_l12a_1p8";
258 regulator-min-microvolt = <1800000>;
259 regulator-max-microvolt = <1800000>;
260 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
261 };
262
263 /* L13 is unused. */
264
265 vreg_l14a_1p88: ldo14 {
266 regulator-name = "vreg_l14a_1p88";
267 regulator-min-microvolt = <1880000>;
268 regulator-max-microvolt = <1880000>;
269 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
270 };
271
272 /* L15 & L16 are unused. */
273
274 vreg_l17a_3p0: ldo17 {
275 regulator-name = "vreg_l17a_3p0";
276 regulator-min-microvolt = <2496000>;
277 regulator-max-microvolt = <3008000>;
278 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
279 regulator-allow-set-load;
280 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
281 RPMH_REGULATOR_MODE_HPM>;
282 };
283
284 vreg_l18a_0p9: ldo18 {
285 regulator-name = "vreg_l18a_0p9";
286 regulator-min-microvolt = <800000>;
287 regulator-max-microvolt = <920000>;
288 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
289 };
290 };
291
292 /*
293 * Remaining regulators that are not yet supported:
294 * OLEDB: 4925000-8100000
295 * ab: 4600000-6100000
296 * ibb: 800000-5400000
297 */
298 regulators-1 {
299 compatible = "qcom,pm8150l-rpmh-regulators";
300 qcom,pmic-id = "c";
301
302 vdd-s1-supply = <&vph_pwr>;
303 vdd-s2-supply = <&vph_pwr>;
304 vdd-s3-supply = <&vph_pwr>;
305 vdd-s4-supply = <&vph_pwr>;
306 vdd-s5-supply = <&vph_pwr>;
307 vdd-s6-supply = <&vph_pwr>;
308 vdd-s7-supply = <&vph_pwr>;
309 vdd-s8-supply = <&vph_pwr>;
310 vdd-l1-l8-supply = <&vreg_s4a_1p8>;
311 vdd-l2-l3-supply = <&vreg_s8c_1p35>;
312 vdd-l4-l5-l6-supply = <&vreg_bob>;
313 vdd-l7-l11-supply = <&vreg_bob>;
314 vdd-l9-l10-supply = <&vreg_bob>;
315 vdd-bob-supply = <&vph_pwr>;
316
317 vreg_bob: bob {
318 regulator-name = "vreg_bob";
319 regulator-min-microvolt = <3350000>;
320 regulator-max-microvolt = <3960000>;
321 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
322 };
323
324 /*
325 * S1-S6 are ARCs:
326 * (S1+S2) - gfx.lvl,
327 * S3 - mx.lvl,
328 * (S4+S5) - mmcx.lvl,
329 * S6 - ebi.lvl
330 */
331
332 vreg_s7c_0p35: smps7 {
333 regulator-name = "vreg_s7c_0p35";
334 regulator-min-microvolt = <348000>;
335 regulator-max-microvolt = <1000000>;
336 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
337 };
338
339 vreg_s8c_1p35: smps8 {
340 regulator-name = "vreg_s8c_1p35";
341 regulator-min-microvolt = <1350000>;
342 regulator-max-microvolt = <1400000>;
343 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
344 };
345
346 vreg_l1c_1p8: ldo1 {
347 regulator-name = "vreg_l1c_1p8";
348 regulator-min-microvolt = <1800000>;
349 regulator-max-microvolt = <1800000>;
350 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
351 };
352
353 /* L2-4 are unused. */
354
355 vreg_l5c_1p8: ldo5 {
356 regulator-name = "vreg_l5c_1p8";
357 regulator-min-microvolt = <1800000>;
358 regulator-max-microvolt = <2800000>;
359 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
360 };
361
362 vreg_l6c_2p9: ldo6 {
363 regulator-name = "vreg_l6c_2p9";
364 regulator-min-microvolt = <1800000>;
365 regulator-max-microvolt = <2960000>;
366 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
367 regulator-allow-set-load;
368 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
369 RPMH_REGULATOR_MODE_HPM>;
370 };
371
372 vreg_l7c_2p85: ldo7 {
373 regulator-name = "vreg_l7c_2p85";
374 regulator-min-microvolt = <2856000>;
375 regulator-max-microvolt = <3104000>;
376 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
377 };
378
379 vreg_l8c_1p8: ldo8 {
380 regulator-name = "vreg_l8c_1p8";
381 regulator-min-microvolt = <1800000>;
382 regulator-max-microvolt = <1800000>;
383 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
384 };
385
386 vreg_l9c_2p9: ldo9 {
387 regulator-name = "vreg_l9c_2p9";
388 regulator-min-microvolt = <2704000>;
389 regulator-max-microvolt = <2960000>;
390 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
391 regulator-allow-set-load;
392 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
393 RPMH_REGULATOR_MODE_HPM>;
394 };
395
396 vreg_l10c_3p3: ldo10 {
397 regulator-name = "vreg_l10c_3p3";
398 regulator-min-microvolt = <3296000>;
399 regulator-max-microvolt = <3296000>;
400 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
401 };
402
403 vreg_l11c_3p0: ldo11 {
404 regulator-name = "vreg_l11c_3p0";
405 regulator-min-microvolt = <3000000>;
406 regulator-max-microvolt = <3000000>;
407 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
408 };
409 };
410
411 regulators-2 {
412 compatible = "qcom,pm8009-rpmh-regulators";
413 qcom,pmic-id = "f";
414
415 vdd-s1-supply = <&vph_pwr>;
416 vdd-s2-supply = <&vreg_bob>;
417 vdd-l2-supply = <&vreg_s8c_1p35>;
418 vdd-l5-l6-supply = <&vreg_bob>;
419 vdd-l7-supply = <&vreg_s4a_1p8>;
420
421 vreg_s1f_1p2: smps1 {
422 regulator-name = "vreg_s1f_1p2";
423 regulator-min-microvolt = <1200000>;
424 regulator-max-microvolt = <1200000>;
425 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
426 };
427
428 vreg_s2f_0p5: smps2 {
429 regulator-name = "vreg_s2f_0p5";
430 regulator-min-microvolt = <512000>;
431 regulator-max-microvolt = <1100000>;
432 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
433 };
434
435 /* L1 is unused. */
436
437 vreg_l2f_1p3: ldo2 {
438 regulator-name = "vreg_l2f_1p3";
439 regulator-min-microvolt = <1304000>;
440 regulator-max-microvolt = <1304000>;
441 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
442 };
443
444 /* L3 & L4 are unused. */
445
446 vreg_l5f_2p8: ldo5 {
447 regulator-name = "vreg_l5f_2p85";
448 regulator-min-microvolt = <2800000>;
449 regulator-max-microvolt = <2800000>;
450 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
451 };
452
453 vreg_l6f_2p8: ldo6 {
454 regulator-name = "vreg_l6f_2p8";
455 regulator-min-microvolt = <2800000>;
456 regulator-max-microvolt = <2800000>;
457 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
458 };
459
460 vreg_l7f_1p8: ldo7 {
461 regulator-name = "vreg_l7f_1p8";
462 regulator-min-microvolt = <1800000>;
463 regulator-max-microvolt = <1800000>;
464 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
465 };
466 };
467};
468
469&cdsp {
470 firmware-name = "qcom/sm8250/xiaomi/elish/cdsp.mbn";
471 status = "okay";
472};
473
474&gmu {
475 status = "okay";
476};
477
478&gpi_dma0 {
479 status = "okay";
480};
481
482&gpi_dma1 {
483 status = "okay";
484};
485
486&gpi_dma2 {
487 status = "okay";
488};
489
490&gpu {
491 status = "okay";
492
493 zap-shader {
494 memory-region = <&gpu_mem>;
495 firmware-name = "qcom/sm8250/xiaomi/elish/a650_zap.mbn";
496 };
497};
498
499&i2c0 {
500 clock-frequency = <400000>;
501 status = "okay";
502
503 fuel-gauge@55 {
504 compatible = "ti,bq27z561";
505 reg = <0x55>;
506 monitored-battery = <&battery_r>;
507 };
508};
509
510&i2c11 {
511 clock-frequency = <400000>;
512 status = "okay";
513
514 backlight: backlight@11 {
515 compatible = "kinetic,ktz8866";
516 reg = <0x11>;
517 vddpos-supply = <&bl_vddpos_5p5>;
518 vddneg-supply = <&bl_vddneg_5p5>;
519 enable-gpios = <&tlmm 139 GPIO_ACTIVE_HIGH>;
520 current-num-sinks = <5>;
521 kinetic,current-ramp-delay-ms = <128>;
522 kinetic,led-enable-ramp-delay-ms = <1>;
523 kinetic,enable-lcd-bias;
524 };
525};
526
527&i2c13 {
528 clock-frequency = <400000>;
529 status = "okay";
530
531 fuel-gauge@55 {
532 compatible = "ti,bq27z561";
533 reg = <0x55>;
534 monitored-battery = <&battery_l>;
535 };
536};
537
538&mdss {
539 status = "okay";
540};
541
542&mdss_dsi0 {
543 vdda-supply = <&vreg_l9a_1p2>;
544 qcom,dual-dsi-mode;
545 qcom,sync-dual-dsi;
546 qcom,master-dsi;
547 status = "okay";
548
549 display_panel: panel@0 {
550 reg = <0>;
551 vddio-supply = <&vreg_l14a_1p88>;
552 reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>;
553 backlight = <&backlight>;
Tom Rini6bb92fc2024-05-20 09:54:58 -0600554 rotation = <90>;
Tom Rini53633a82024-02-29 12:33:36 -0500555
556 status = "disabled";
557
558 ports {
559 #address-cells = <1>;
560 #size-cells = <0>;
561
562 port@0 {
563 reg = <0>;
564
565 panel_in_0: endpoint {
566 remote-endpoint = <&mdss_dsi0_out>;
567 };
568 };
569
570 port@1 {
571 reg = <1>;
572
573 panel_in_1: endpoint {
574 remote-endpoint = <&mdss_dsi1_out>;
575 };
576 };
577 };
578 };
579};
580
581&mdss_dsi0_out {
582 data-lanes = <0 1 2>;
583 remote-endpoint = <&panel_in_0>;
584};
585
586&mdss_dsi0_phy {
587 vdds-supply = <&vreg_l5a_0p88>;
588 phy-type = <PHY_TYPE_CPHY>;
589 status = "okay";
590};
591
592&mdss_dsi1 {
593 vdda-supply = <&vreg_l9a_1p2>;
594 qcom,dual-dsi-mode;
595 qcom,sync-dual-dsi;
596 /* DSI1 is slave, so use DSI0 clocks */
597 assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
598 status = "okay";
599};
600
601&mdss_dsi1_out {
602 data-lanes = <0 1 2>;
603 remote-endpoint = <&panel_in_1>;
604};
605
606&mdss_dsi1_phy {
607 vdds-supply = <&vreg_l5a_0p88>;
608 phy-type = <PHY_TYPE_CPHY>;
609 status = "okay";
610};
611
612&pcie0 {
613 status = "okay";
614};
615
616&pcie0_phy {
617 vdda-phy-supply = <&vreg_l5a_0p88>;
618 vdda-pll-supply = <&vreg_l9a_1p2>;
619 status = "okay";
620};
621
622&pm8150_gpios {
623 vol_up_n: vol-up-n-state {
624 pins = "gpio6";
625 function = "normal";
626 power-source = <1>;
627 input-enable;
628 bias-pull-up;
629 };
630};
631
Tom Rini93743d22024-04-01 09:08:13 -0400632&pm8150b_typec {
633 vdd-pdphy-supply = <&vreg_l2a_3p1>;
634 status = "okay";
635
636 connector {
637 compatible = "usb-c-connector";
638
639 power-role = "source";
640 data-role = "dual";
641 self-powered;
642
643 source-pdos = <PDO_FIXED(5000, 3000,
644 PDO_FIXED_DUAL_ROLE |
645 PDO_FIXED_USB_COMM |
646 PDO_FIXED_DATA_SWAP)>;
647
648 ports {
649 #address-cells = <1>;
650 #size-cells = <0>;
651
652 port@0 {
653 reg = <0>;
654
655 pm8150b_role_switch_in: endpoint {
656 remote-endpoint = <&usb_1_role_switch_out>;
657 };
658 };
659 };
660 };
661};
662
663&pm8150b_vbus {
664 status = "okay";
665};
666
Tom Rini53633a82024-02-29 12:33:36 -0500667&pon_pwrkey {
668 status = "okay";
669};
670
671&pon_resin {
672 linux,code = <KEY_VOLUMEDOWN>;
673 status = "okay";
674};
675
676&qupv3_id_0 {
677 status = "okay";
678};
679
680&qupv3_id_1 {
681 status = "okay";
682};
683
684&qupv3_id_2 {
685 status = "okay";
686};
687
688&slpi {
689 firmware-name = "qcom/sm8250/xiaomi/elish/slpi.mbn";
690 status = "okay";
691};
692
693&tlmm {
694 gpio-reserved-ranges = <40 4>;
695};
696
697&usb_1 {
698 /* USB 2.0 only */
699 qcom,select-utmi-as-pipe-clk;
700 status = "okay";
701};
702
703&usb_1_dwc3 {
Tom Rini93743d22024-04-01 09:08:13 -0400704 dr_mode = "otg";
Tom Rini53633a82024-02-29 12:33:36 -0500705 maximum-speed = "high-speed";
706 /* Remove USB3 phy */
707 phys = <&usb_1_hsphy>;
708 phy-names = "usb2-phy";
Tom Rini93743d22024-04-01 09:08:13 -0400709 usb-role-switch;
Tom Rini53633a82024-02-29 12:33:36 -0500710};
711
712&usb_1_hsphy {
713 vdda-pll-supply = <&vreg_l5a_0p88>;
714 vdda18-supply = <&vreg_l12a_1p8>;
715 vdda33-supply = <&vreg_l2a_3p1>;
716 status = "okay";
717};
718
Tom Rini93743d22024-04-01 09:08:13 -0400719&usb_1_role_switch_out {
720 remote-endpoint = <&pm8150b_role_switch_in>;
721};
722
Tom Rini53633a82024-02-29 12:33:36 -0500723&ufs_mem_hc {
724 vcc-supply = <&vreg_l17a_3p0>;
725 vcc-max-microamp = <800000>;
726 vccq-supply = <&vreg_l6a_1p2>;
727 vccq-max-microamp = <800000>;
728 vccq2-supply = <&vreg_s4a_1p8>;
729 vccq2-max-microamp = <800000>;
730 status = "okay";
731};
732
733&ufs_mem_phy {
734 vdda-phy-supply = <&vreg_l5a_0p88>;
735 vdda-pll-supply = <&vreg_l9a_1p2>;
736 status = "okay";
737};
738
739&venus {
740 firmware-name = "qcom/sm8250/xiaomi/elish/venus.mbn";
741 status = "okay";
742};