blob: 0335a0098585f67898666311e88c6d2bf111e72f [file] [log] [blame]
Stefan Roese6e7fb6e2005-11-29 18:18:21 +01001/*
2 * (C) Copyright 2005
3 * Stefan Roese, DENX Software Engineering, sr@denx.de.
4 * John Otken, jotken@softadvances.com
5 *
6 * See file CREDITS for list of people who contributed to this
7 * project.
8 *
9 * This program is free software; you can redistribute it and/or
10 * modify it under the terms of the GNU General Public License as
11 * published by the Free Software Foundation; either version 2 of
12 * the License, or (at your option) any later version.
13 *
14 * This program is distributed in the hope that it will be useful,
15 * but WITHOUT ANY WARRANTY; without even the implied warranty of
16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
17 * GNU General Public License for more details.
18 *
19 * You should have received a copy of the GNU General Public License
20 * along with this program; if not, write to the Free Software
21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
22 * MA 02111-1307 USA
23 */
24
25/************************************************************************
26 * luan.h - configuration for LUAN board
27 ***********************************************************************/
28#ifndef __CONFIG_H
29#define __CONFIG_H
30
31/*-----------------------------------------------------------------------
32 * High Level Configuration Options
33 *----------------------------------------------------------------------*/
34#define CONFIG_LUAN 1 /* Board is Luan */
35#define CONFIG_440SP 1 /* Specific PPC440SP support */
36#define CONFIG_4xx 1 /* PPC4xx family */
37#define CONFIG_440 1
38#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
39
40#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
41#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
42
43/*-----------------------------------------------------------------------
44 * Base addresses -- Note these are effective addresses where the
45 * actual resources get mapped (not physical addresses)
46 *----------------------------------------------------------------------*/
47#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
48#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc */
49#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
50#define CFG_SDRAM_BASE 0x00000000 /* MUST be zero */
51
52#define CFG_LARGE_FLASH 0xffc00000 /* 4MB flash address CS0 */
53#define CFG_SMALL_FLASH 0xff900000 /* 1MB flash address CS2 */
54#define CFG_SRAM_BASE 0xff800000 /* 1MB SRAM address CS2 */
55#define CFG_EPLD_BASE 0xff000000 /* EPLD and FRAM CS1 */
56
57#define CFG_ISRAM_BASE 0xf8000000 /* internal 8k SRAM (L2 cache) */
58
59#define CFG_PERIPHERAL_BASE 0xf0000000 /* internal peripherals */
60
61#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
62#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
63#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */
64
65#if CFG_LARGE_FLASH == 0xffc00000
66#define CFG_FLASH_BASE CFG_LARGE_FLASH
67#else
68#define CFG_FLASH_BASE CFG_SMALL_FLASH
69#endif
70
71#undef CFG_DRAM_TEST
72#if CFG_SRAM_BASE
73#define CFG_KBYTES_SDRAM 1024*2
74#else
75#define CFG_KBYTES_SDRAM 1024
76#endif
77
78/*-----------------------------------------------------------------------
79 * Initial RAM & stack pointer (placed in SDRAM)
80 *----------------------------------------------------------------------*/
81#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE
82#define CFG_INIT_RAM_END (8 << 10)
83#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
84#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
85#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
86
87/*-----------------------------------------------------------------------
88 * Serial Port
89 *----------------------------------------------------------------------*/
90#define CFG_EXT_SERIAL_CLOCK 11059200 /* external 11.059MHz clk */
91#define CONFIG_BAUDRATE 115200
92#undef CONFIG_SERIAL_MULTI
93#undef CONFIG_UART1_CONSOLE /* define if you want console on UART1 */
94
95#define CFG_BAUDRATE_TABLE \
96 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
97
98/*-----------------------------------------------------------------------
99 * Environment
100 *----------------------------------------------------------------------*/
101/*
102 * Define here the location of the environment variables (FLASH or EEPROM).
103 * Note: DENX encourages to use redundant environment in FLASH.
104 */
105#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
106
107/*-----------------------------------------------------------------------
108 * FLASH related
109 *----------------------------------------------------------------------*/
110#define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */
111#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
112
113#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
114#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
115
116#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
117
118#define CFG_FLASH_ADDR0 0x555
119#define CFG_FLASH_ADDR1 0x2aa
120#define CFG_FLASH_WORD_SIZE unsigned char
121
122#ifdef CFG_ENV_IS_IN_FLASH
123#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
124#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
125#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
126
127/* Address and size of Redundant Environment Sector */
128#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
129#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
130#endif /* CFG_ENV_IS_IN_FLASH */
131
132/*-----------------------------------------------------------------------
133 * DDR SDRAM
134 *----------------------------------------------------------------------*/
135#undef CONFIG_SPD_EEPROM /* SPD EEPROM init doesn't support DDR2 */
136#define SPD_EEPROM_ADDRESS {0x52,0x53} /* I2C SPD addresses */
137#define IIC0_DIMM0_ADDR 0x52
138#define IIC0_DIMM1_ADDR 0x53
139
140/*-----------------------------------------------------------------------
141 * I2C
142 *----------------------------------------------------------------------*/
143#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
144#undef CONFIG_SOFT_I2C /* I2C bit-banged */
145#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
146#define CFG_I2C_SLAVE 0x7F
147
148#define CONFIG_PREBOOT "echo;" \
149 "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
150 "echo"
151
152#undef CONFIG_BOOTARGS
153
154#define CONFIG_EXTRA_ENV_SETTINGS \
155 "netdev=eth0\0" \
156 "hostname=luan\0" \
157 "nfsargs=setenv bootargs root=/dev/nfs rw " \
158 "nfsroot=$(serverip):$(rootpath)\0" \
159 "ramargs=setenv bootargs root=/dev/ram rw\0" \
160 "addip=setenv bootargs $(bootargs) " \
161 "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
162 ":$(hostname):$(netdev):off panic=1\0" \
163 "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\
164 "flash_nfs=run nfsargs addip addtty;" \
165 "bootm $(kernel_addr)\0" \
166 "flash_self=run ramargs addip addtty;" \
167 "bootm $(kernel_addr) $(ramdisk_addr)\0" \
168 "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \
169 "bootm\0" \
170 "rootpath=/opt/eldk/ppc_4xx\0" \
171 "bootfile=/tftpboot/luan/uImage\0" \
172 "kernel_addr=fc000000\0" \
173 "ramdisk_addr=fc100000\0" \
174 "load=tftp 100000 /tftpboot/luan/u-boot.bin\0" \
175 "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
176 "cp.b 100000 fffc0000 40000;" \
177 "setenv filesize;saveenv\0" \
178 "upd=run load;run update\0" \
179 ""
180#define CONFIG_BOOTCOMMAND "run flash_self"
181
182#if 0
183#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
184#else
185#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
186#endif
187
188#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
189#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
190
191#define CONFIG_MII 1 /* MII PHY management */
192#define CONFIG_PHY_ADDR 1
193#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
194#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
195
196#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
197
198#define CONFIG_NETCONSOLE /* include NetConsole support */
199#define CONFIG_NET_MULTI /* needed for NetConsole */
200
201/* Partitions */
202#define CONFIG_MAC_PARTITION
203#define CONFIG_DOS_PARTITION
204#define CONFIG_ISO_PARTITION
205
206#ifdef DEBUG
207#define CONFIG_PANIC_HANG
208#else
209#define CONFIG_HW_WATCHDOG /* watchdog */
210#endif
211
212#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
213 CFG_CMD_ASKENV | \
214 CFG_CMD_CACHE | \
215 CFG_CMD_DHCP | \
216 CFG_CMD_DIAG | \
217 CFG_CMD_ELF | \
218 CFG_CMD_I2C | \
219 CFG_CMD_IRQ | \
220 CFG_CMD_MII | \
221 CFG_CMD_NET | \
222 CFG_CMD_NFS | \
223 CFG_CMD_PCI | \
224 CFG_CMD_PING | \
225 CFG_CMD_REGINFO | \
226 CFG_CMD_SETGETDCR | \
227 CFG_CMD_SDRAM | \
228 0)
229
230/* this must be included AFTER the definition of CONFIG_COMMANDS */
231#include <cmd_confdefs.h>
232
233/*
234 * Miscellaneous configurable options
235 */
236#define CFG_LONGHELP /* undef to save memory */
237#define CFG_PROMPT "=> " /* Monitor Command Prompt */
238#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
239#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
240#else
241#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
242#endif
243#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
244#define CFG_MAXARGS 16 /* max number of command args */
245#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
246
247#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
248#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
249
250#define CFG_LOAD_ADDR 0x100000 /* default load address */
251#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
252#undef CONFIG_LYNXKDI /* support kdi files */
253
254#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
255
256/*-----------------------------------------------------------------------
257 * PCI stuff
258 *-----------------------------------------------------------------------
259 */
260#if (CONFIG_COMMANDS & CFG_CMD_PCI)
261
262/* General PCI */
263#define CONFIG_PCI /* include pci support */
264#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */
265#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
266
267/* Board-specific PCI */
268#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
269#define CFG_PCI_TARGET_INIT
270#undef CFG_PCI_MASTER_INIT
271
272#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
273#define CFG_PCI_SUBSYS_DEVICEID 0x4403 /* whatever */
274
275#endif /* CONFIG_COMMANDS & CFG_CMD_PCI */
276
277/*
278 * For booting Linux, the board info and command line data
279 * have to be in the first 8 MB of memory, since this is
280 * the maximum mapped by the Linux kernel during initialization.
281 */
282#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
283
284/*-----------------------------------------------------------------------
285 * Cache Configuration
286 */
287#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */
288#define CFG_CACHELINE_SIZE 32 /* ... */
289#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
290#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
291#endif
292
293/*
294 * Internal Definitions
295 *
296 * Boot Flags
297 */
298#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
299#define BOOTFLAG_WARM 0x02 /* Software reboot */
300
301#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
302#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
303#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
304#endif
305
306#endif /* __CONFIG_H */