blob: dc15b0c3498e442d40ec97e13276b4f9c7bffc3a [file] [log] [blame]
wdenke2211742002-11-02 23:30:20 +00001/*
2 * (C) Copyright 2001
3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
4 *
5 * See file CREDITS for list of people who contributed to this
6 * project.
7 *
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License as
10 * published by the Free Software Foundation; either version 2 of
11 * the License, or (at your option) any later version.
12 *
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
21 * MA 02111-1307 USA
22 */
23
24/*
25 * board/config.h - configuration options, board specific
26 */
27
28#ifndef __CONFIG_H
29#define __CONFIG_H
30
31/*
32 * High Level Configuration Options
33 * (easy to change)
34 */
35
36#define CONFIG_405GP 1 /* This is a PPC405 CPU */
37#define CONFIG_4xx 1 /* ...member of PPC4xx family */
38#define CONFIG_ERIC 1 /* ...on a ERIC board */
39
wdenkc837dcb2004-01-20 23:12:12 +000040#define CONFIG_BOARD_EARLY_INIT_F 1 /* run board_early_init_f() */
wdenke2211742002-11-02 23:30:20 +000041
42#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
43
44#if 1
45#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
46#endif
47#if 0
48#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
49#endif
50#if 0
51#define CFG_ENV_IS_IN_EEPROM 1 /* use I2C RTC X1240 for environment vars */
52#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
53#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars */
54#endif /* total size of a X1240 is 2048 bytes */
55
56#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
57#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
58#define CFG_I2C_SLAVE 0x7F
59
60#define CFG_I2C_EEPROM_ADDR 0x57 /* X1240 has two I2C slave addresses, one for EEPROM */
61#define CFG_I2C_EEPROM_ADDR_LEN 2 /* address length for the eeprom */
62#define CONFIG_I2C_RTC 1 /* we have a Xicor X1240 RTC */
63#define CFG_I2C_RTC_ADDR 0x6F /* and one for RTC */
64
65#ifdef CFG_ENV_IS_IN_FLASH
66#undef CFG_ENV_IS_IN_NVRAM
67#undef CFG_ENV_IS_IN_EEPROM
68#else
69#ifdef CFG_ENV_IS_IN_NVRAM
70#undef CFG_ENV_IS_IN_FLASH
71#undef CFG_ENV_IS_IN_EEPROM
72#else
73#ifdef CFG_ENV_IS_IN_EEPROM
74#undef CFG_ENV_IS_IN_NVRAM
75#undef CFG_ENV_IS_IN_FLASH
76#endif
77#endif
78#endif
79
80#define CONFIG_BAUDRATE 115200
81#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
82
83#if 1
84#define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */
85#else
86#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
87#endif
88
89#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/nfs " \
90 "nfsroot=192.168.1.2:/eric_root_devel " \
91 "ip=192.168.1.22:192.168.1.2"
92
93#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
94#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
95
96#define CONFIG_MII 1 /* MII PHY management */
97#define CONFIG_PHY_ADDR 1 /* PHY address */
98
wdenke2211742002-11-02 23:30:20 +000099
100/*
Jon Loeliger11799432007-07-10 09:02:57 -0500101 * BOOTP options
102 */
103#define CONFIG_BOOTP_BOOTFILESIZE
104#define CONFIG_BOOTP_BOOTPATH
105#define CONFIG_BOOTP_GATEWAY
106#define CONFIG_BOOTP_HOSTNAME
107
108
109/*
Jon Loeligerdcaa7152007-07-07 20:56:05 -0500110 * Command line configuration.
wdenke2211742002-11-02 23:30:20 +0000111 */
Jon Loeligerdcaa7152007-07-07 20:56:05 -0500112#include <config_cmd_default.h>
wdenke2211742002-11-02 23:30:20 +0000113
Jon Loeligerdcaa7152007-07-07 20:56:05 -0500114#define CONFIG_CMD_PCI
115#define CONFIG_CMD_IRQ
116#define CONFIG_CMD_ENV
117#define CONFIG_CMD_FLASH
118
wdenke2211742002-11-02 23:30:20 +0000119
120#undef CONFIG_WATCHDOG /* watchdog disabled */
121
122/*
123 * Miscellaneous configurable options
124 */
125#undef CFG_LONGHELP /* undef to save memory */
126#define CFG_PROMPT "=> " /* Monitor Command Prompt */
Jon Loeligerdcaa7152007-07-07 20:56:05 -0500127#if defined(CONFIG_CMD_KGDB)
wdenke2211742002-11-02 23:30:20 +0000128#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
129#else
130#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
131#endif
132#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
133#define CFG_MAXARGS 16 /* max number of command args */
134#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
135
136#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
137#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
138
139#define CFG_EXT_SERIAL_CLOCK 14318180
140
141/* The following table includes the supported baudrates */
142#define CFG_BAUDRATE_TABLE \
143 { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
144 57600, 115200, 230400, 460800, 921600 }
145
146#define CFG_LOAD_ADDR 0x100000 /* default load address */
147#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
148
149#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
150
151/*-----------------------------------------------------------------------
152 * PCI stuff
153 *-----------------------------------------------------------------------
154 */
155#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
156#define PCI_HOST_FORCE 1 /* configure as pci host */
157#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
158
159#define CONFIG_PCI /* include pci support */
160#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
161#undef CONFIG_PCI_PNP /* no pci plug-and-play */
wdenk8bde7f72003-06-27 21:31:46 +0000162 /* resource configuration */
wdenke2211742002-11-02 23:30:20 +0000163
164#define CFG_PCI_SUBSYS_VENDORID 0x1743 /* PCI Vendor ID: Peppercon AG */
165#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: 405GP */
166#define CFG_PCI_PTM1LA 0xFFFC0000 /* point to flash */
167#define CFG_PCI_PTM1MS 0xFFFFF001 /* 4kB, enable hard-wired to 1 */
168#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
169#define CFG_PCI_PTM2LA 0x00000000 /* disabled */
170#define CFG_PCI_PTM2MS 0x00000000 /* disabled */
171#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
172
173/*-----------------------------------------------------------------------
174 * External peripheral base address
175 *-----------------------------------------------------------------------
176 */
177/* Bank 0 - Flash/SRAM 0xFF000000 16MB 16 Bit */
178/* Bank 1 - NVRAM/RTC 0xF0000000 1MB 8 Bit */
179/* Bank 2 - A/D converter 0xF0100000 1MB 8 Bit */
180/* Bank 3 - Ethernet PHY Reset 0xF0200000 1MB 8 Bit */
181/* Bank 4 - PC-MIP PRSNT1# 0xF0300000 1MB 8 Bit */
182/* Bank 5 - PC-MIP PRSNT2# 0xF0400000 1MB 8 Bit */
183/* Bank 6 - CPU LED0 0xF0500000 1MB 8 Bit */
184/* Bank 7 - CPU LED1 0xF0600000 1MB 8 Bit */
185
186/* ----------------------------------------------------------------------- */
187/* Memory Bank 0 (Flash) initialization */
188/* ----------------------------------------------------------------------- */
189#define CS0_AP 0x9B015480
190#define CS0_CR 0xFF87A000 /* BAS=0xFF8,BS=(8MB),BU=0x3(R/W), BW=(16 bits) */
191/* ----------------------------------------------------------------------- */
192/* Memory Bank 1 (NVRAM/RTC) initialization */
193/* ----------------------------------------------------------------------- */
194#define CS1_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
195#define CS1_CR 0xF0018000 /* BAS=0xF00,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
196 /* ----------------------------------------------------------------------- */
197 /* Memory Bank 2 (A/D converter) initialization */
198 /* ----------------------------------------------------------------------- */
199#define CS2_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
200#define CS2_CR 0xF0118000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
201/* ----------------------------------------------------------------------- */
202/* Memory Bank 3 (Ethernet PHY Reset) initialization */
203/* ----------------------------------------------------------------------- */
204#define CS3_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
205#define CS3_CR 0xF0218000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
206/* ----------------------------------------------------------------------- */
207/* Memory Bank 4 (PC-MIP PRSNT1#) initialization */
208/* ----------------------------------------------------------------------- */
209#define CS4_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
210#define CS4_CR 0xF0318000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
211/* ----------------------------------------------------------------------- */
212/* Memory Bank 5 (PC-MIP PRSNT2#) initialization */
213/* ----------------------------------------------------------------------- */
214#define CS5_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
215#define CS5_CR 0xF0418000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
216/* ----------------------------------------------------------------------- */
217/* Memory Bank 6 (CPU LED0) initialization */
218/* ----------------------------------------------------------------------- */
219#define CS6_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
220#define CS6_CR 0xF0518000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
221/* ----------------------------------------------------------------------- */
222/* Memory Bank 7 (CPU LED1) initialization */
223/* ----------------------------------------------------------------------- */
224#define CS7_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
225#define CS7_CR 0xF0618000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
226
227#define CFG_NVRAM_REG_BASE_ADDR 0xF0000000
228#define CFG_RTC_REG_BASE_ADDR (0xF0000000 + 0x7F8)
229#define CFG_ADC_REG_BASE_ADDR 0xF0100000
230#define CFG_PHYRES_REG_BASE_ADDR 0xF0200000
231#define CFG_PRSNT1_REG_BASE_ADDR 0xF0300000
232#define CFG_PRSNT2_REG_BASE_ADDR 0xF0400000
233#define CFG_LED0_REG_BASE_ADDR 0xF0500000
234#define CFG_LED1_REG_BASE_ADDR 0xF0600000
235
236
237/* SDRAM CONFIG */
238#define CFG_SDRAM_MANUALLY 1
239#define CFG_SDRAM_SINGLE_BANK 1
240
241#ifdef CFG_SDRAM_MANUALLY
242/*-----------------------------------------------------------------------
243 * Set MB0CF for bank 0. (0-32MB) Address Mode 4 since 12x8(2)
244 *----------------------------------------------------------------------*/
245#define MB0CF 0x00062001 /* 32MB @ 0 */
246/*-----------------------------------------------------------------------
247 * Set MB1CF for bank 1. (32MB-64MB) Address Mode 4 since 12x8(2)
248 *----------------------------------------------------------------------*/
249#ifdef CFG_SDRAM_SINGLE_BANK
250#define MB1CF 0x0 /* 0MB @ 32MB */
251#else
252#define MB1CF 0x02062001 /* 32MB @ 32MB */
253#endif
254/*-----------------------------------------------------------------------
255 * Set MB2CF for bank 2. off
256 *----------------------------------------------------------------------*/
257#define MB2CF 0x0 /* 0MB */
258/*-----------------------------------------------------------------------
259 * Set MB3CF for bank 3. off
260 *----------------------------------------------------------------------*/
261#define MB3CF 0x0 /* 0MB */
262
263#define SDTR_100 0x0086400D
264#define RTR_100 0x05F0
265#define SDTR_66 0x00854006 /* orig U-Boot-wallnut says 0x00854006 */
266#define RTR_66 0x03f8
267
268#endif /* CFG_SDRAM_MANUALLY */
269
270
271/*-----------------------------------------------------------------------
272 * Start addresses for the final memory configuration
273 * (Set up by the startup code)
274 * Please note that CFG_SDRAM_BASE _must_ start at 0
275 */
276#define CFG_SDRAM_BASE 0x00000000
277#define CFG_SDRAM_SIZE 32
278#define CFG_FLASH_BASE 0xFF800000 /* 8 MByte Flash */
279#define CFG_MONITOR_BASE 0xFFFE0000 /* last 128kByte within Flash */
280/*#define CFG_MONITOR_LEN (192 * 1024)*/ /* Reserve 196 kB for Monitor */
281#define CFG_MONITOR_LEN (128 * 1024) /* Reserve 128 kB for Monitor */
282#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
283
284/*
285 * For booting Linux, the board info and command line data
286 * have to be in the first 8 MB of memory, since this is
287 * the maximum mapped by the Linux kernel during initialization.
288 */
289#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
290/*-----------------------------------------------------------------------
291 * FLASH organization
292 */
293#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
294#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
295#define CFG_FLASH_16BIT 1 /* Rom 16 bit data bus */
296
297#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
298#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
299
300/* BEG ENVIRONNEMENT FLASH */
301#ifdef CFG_ENV_IS_IN_FLASH
302#define CFG_ENV_SECT_SIZE (128*1024)
303
304#if 0 /* force ENV to be NOT embedded */
305#define CFG_ENV_ADDR 0xfffa0000
306#else /* force ENV to be embedded */
307#define CFG_ENV_SIZE (2 * 1024) /* Total Size of Environment Sector 2k */
308#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN - CFG_ENV_SIZE - 0x10) /* let space for reset vector */
309/* #define CFG_ENV_ADDR (CFG_MONITOR_BASE)*/
310#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
311#endif
312
313#endif
314/* END ENVIRONNEMENT FLASH */
315/*-----------------------------------------------------------------------
316 * NVRAM organization
317 */
318#define CFG_NVRAM_BASE_ADDR CFG_NVRAM_REG_BASE_ADDR /* NVRAM base address */
319#define CFG_NVRAM_SIZE 0x7F8 /* NVRAM size 2kByte - 8 Byte for RTC */
320
321#ifdef CFG_ENV_IS_IN_NVRAM
322#define CFG_ENV_SIZE 0x7F8 /* Size of Environment vars */
323#define CFG_ENV_ADDR \
324 (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */
325#endif
wdenke2211742002-11-02 23:30:20 +0000326
327/*
328 * Init Memory Controller:
329 *
330 * BR0/1 and OR0/1 (FLASH)
331 */
332
333#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 8MB */
334#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
335
336
337/* Configuration Port location */
338/* #define CONFIG_PORT_ADDR 0xF0000500 */
339
340/*-----------------------------------------------------------------------
341 * Definitions for initial stack pointer and data area (in DPRAM)
342 */
343#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
344#define CFG_INIT_RAM_END 0x0f00 /* End of used area in RAM */
345#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
346#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
347#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
348
349/*-----------------------------------------------------------------------
350 * Definitions for Serial Presence Detect EEPROM address
351 * (to get SDRAM settings)
352 */
353#define SPD_EEPROM_ADDRESS 0x50
354
355/*
356 * Internal Definitions
357 *
358 * Boot Flags
359 */
360#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
361#define BOOTFLAG_WARM 0x02 /* Software reboot */
362
Jon Loeligerdcaa7152007-07-07 20:56:05 -0500363#if defined(CONFIG_CMD_KGDB)
wdenke2211742002-11-02 23:30:20 +0000364#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
365#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
366#endif
367#endif /* __CONFIG_H */