blob: 588a84d7a919449e17a0ea5801caa30301f70660 [file] [log] [blame]
Reinhard Meyera61a8192010-09-12 16:23:49 +02001/*
2 * (C) Copyright 2010
3 * Reinhard Meyer, EMK Elektronik, reinhard.meyer@emk-elektronik.de
4 * Martin Krause, Martin.Krause@tqs.de
5 * reworked original enc28j60.c
6 *
Wolfgang Denk1a459662013-07-08 09:37:19 +02007 * SPDX-License-Identifier: GPL-2.0+
Reinhard Meyera61a8192010-09-12 16:23:49 +02008 */
9
10#include <common.h>
11#include <net.h>
12#include <spi.h>
13#include <malloc.h>
14#include <netdev.h>
15#include <miiphy.h>
16#include "enc28j60.h"
17
18/*
19 * IMPORTANT: spi_claim_bus() and spi_release_bus()
20 * are called at begin and end of each of the following functions:
21 * enc_miiphy_read(), enc_miiphy_write(), enc_write_hwaddr(),
22 * enc_init(), enc_recv(), enc_send(), enc_halt()
23 * ALL other functions assume that the bus has already been claimed!
Joe Hershberger1fd92db2015-04-08 01:41:06 -050024 * Since net_process_received_packet() might call enc_send() in return, the bus
25 * must be released, net_process_received_packet() called and claimed again.
Reinhard Meyera61a8192010-09-12 16:23:49 +020026 */
27
28/*
29 * Controller memory layout.
30 * We only allow 1 frame for transmission and reserve the rest
31 * for reception to handle as many broadcast packets as possible.
32 * Also use the memory from 0x0000 for receiver buffer. See errata pt. 5
33 * 0x0000 - 0x19ff 6656 bytes receive buffer
34 * 0x1a00 - 0x1fff 1536 bytes transmit buffer =
35 * control(1)+frame(1518)+status(7)+reserve(10).
36 */
37#define ENC_RX_BUF_START 0x0000
38#define ENC_RX_BUF_END 0x19ff
39#define ENC_TX_BUF_START 0x1a00
40#define ENC_TX_BUF_END 0x1fff
41#define ENC_MAX_FRM_LEN 1518
42#define RX_RESET_COUNTER 1000
43
44/*
45 * For non data transfer functions, like phy read/write, set hwaddr, init
46 * we do not need a full, time consuming init including link ready wait.
47 * This enum helps to bring the chip through the minimum necessary inits.
48 */
49enum enc_initstate {none=0, setupdone, linkready};
50typedef struct enc_device {
51 struct eth_device *dev; /* back pointer */
52 struct spi_slave *slave;
53 int rx_reset_counter;
54 u16 next_pointer;
55 u8 bank; /* current bank in enc28j60 */
56 enum enc_initstate initstate;
57} enc_dev_t;
58
59/*
60 * enc_bset: set bits in a common register
61 * enc_bclr: clear bits in a common register
62 *
63 * making the reg parameter u8 will give a compile time warning if the
64 * functions are called with a register not accessible in all Banks
65 */
66static void enc_bset(enc_dev_t *enc, const u8 reg, const u8 data)
67{
68 u8 dout[2];
69
70 dout[0] = CMD_BFS(reg);
71 dout[1] = data;
72 spi_xfer(enc->slave, 2 * 8, dout, NULL,
73 SPI_XFER_BEGIN | SPI_XFER_END);
74}
75
76static void enc_bclr(enc_dev_t *enc, const u8 reg, const u8 data)
77{
78 u8 dout[2];
79
80 dout[0] = CMD_BFC(reg);
81 dout[1] = data;
82 spi_xfer(enc->slave, 2 * 8, dout, NULL,
83 SPI_XFER_BEGIN | SPI_XFER_END);
84}
85
86/*
87 * high byte of the register contains bank number:
88 * 0: no bank switch necessary
89 * 1: switch to bank 0
90 * 2: switch to bank 1
91 * 3: switch to bank 2
92 * 4: switch to bank 3
93 */
94static void enc_set_bank(enc_dev_t *enc, const u16 reg)
95{
96 u8 newbank = reg >> 8;
97
98 if (newbank == 0 || newbank == enc->bank)
99 return;
100 switch (newbank) {
101 case 1:
102 enc_bclr(enc, CTL_REG_ECON1,
103 ENC_ECON1_BSEL0 | ENC_ECON1_BSEL1);
104 break;
105 case 2:
106 enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_BSEL0);
107 enc_bclr(enc, CTL_REG_ECON1, ENC_ECON1_BSEL1);
108 break;
109 case 3:
110 enc_bclr(enc, CTL_REG_ECON1, ENC_ECON1_BSEL0);
111 enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_BSEL1);
112 break;
113 case 4:
114 enc_bset(enc, CTL_REG_ECON1,
115 ENC_ECON1_BSEL0 | ENC_ECON1_BSEL1);
116 break;
117 }
118 enc->bank = newbank;
119}
120
121/*
122 * local functions to access SPI
123 *
124 * reg: register inside ENC28J60
125 * data: 8/16 bits to write
126 * c: number of retries
127 *
128 * enc_r8: read 8 bits
129 * enc_r16: read 16 bits
130 * enc_w8: write 8 bits
131 * enc_w16: write 16 bits
132 * enc_w8_retry: write 8 bits, verify and retry
133 * enc_rbuf: read from ENC28J60 into buffer
134 * enc_wbuf: write from buffer into ENC28J60
135 */
136
137/*
138 * MAC and MII registers need a 3 byte SPI transfer to read,
139 * all other registers need a 2 byte SPI transfer.
140 */
141static int enc_reg2nbytes(const u16 reg)
142{
143 /* check if MAC or MII register */
144 return ((reg >= CTL_REG_MACON1 && reg <= CTL_REG_MIRDH) ||
145 (reg >= CTL_REG_MAADR1 && reg <= CTL_REG_MAADR4) ||
146 (reg == CTL_REG_MISTAT)) ? 3 : 2;
147}
148
149/*
150 * Read a byte register
151 */
152static u8 enc_r8(enc_dev_t *enc, const u16 reg)
153{
154 u8 dout[3];
155 u8 din[3];
156 int nbytes = enc_reg2nbytes(reg);
157
158 enc_set_bank(enc, reg);
159 dout[0] = CMD_RCR(reg);
160 spi_xfer(enc->slave, nbytes * 8, dout, din,
161 SPI_XFER_BEGIN | SPI_XFER_END);
162 return din[nbytes-1];
163}
164
165/*
166 * Read a L/H register pair and return a word.
167 * Must be called with the L register's address.
168 */
169static u16 enc_r16(enc_dev_t *enc, const u16 reg)
170{
171 u8 dout[3];
172 u8 din[3];
173 u16 result;
174 int nbytes = enc_reg2nbytes(reg);
175
176 enc_set_bank(enc, reg);
177 dout[0] = CMD_RCR(reg);
178 spi_xfer(enc->slave, nbytes * 8, dout, din,
179 SPI_XFER_BEGIN | SPI_XFER_END);
180 result = din[nbytes-1];
181 dout[0]++; /* next register */
182 spi_xfer(enc->slave, nbytes * 8, dout, din,
183 SPI_XFER_BEGIN | SPI_XFER_END);
184 result |= din[nbytes-1] << 8;
185 return result;
186}
187
188/*
189 * Write a byte register
190 */
191static void enc_w8(enc_dev_t *enc, const u16 reg, const u8 data)
192{
193 u8 dout[2];
194
195 enc_set_bank(enc, reg);
196 dout[0] = CMD_WCR(reg);
197 dout[1] = data;
198 spi_xfer(enc->slave, 2 * 8, dout, NULL,
199 SPI_XFER_BEGIN | SPI_XFER_END);
200}
201
202/*
203 * Write a L/H register pair.
204 * Must be called with the L register's address.
205 */
206static void enc_w16(enc_dev_t *enc, const u16 reg, const u16 data)
207{
208 u8 dout[2];
209
210 enc_set_bank(enc, reg);
211 dout[0] = CMD_WCR(reg);
212 dout[1] = data;
213 spi_xfer(enc->slave, 2 * 8, dout, NULL,
214 SPI_XFER_BEGIN | SPI_XFER_END);
215 dout[0]++; /* next register */
216 dout[1] = data >> 8;
217 spi_xfer(enc->slave, 2 * 8, dout, NULL,
218 SPI_XFER_BEGIN | SPI_XFER_END);
219}
220
221/*
222 * Write a byte register, verify and retry
223 */
224static void enc_w8_retry(enc_dev_t *enc, const u16 reg, const u8 data, const int c)
225{
226 u8 dout[2];
227 u8 readback;
228 int i;
229
230 enc_set_bank(enc, reg);
231 for (i = 0; i < c; i++) {
232 dout[0] = CMD_WCR(reg);
233 dout[1] = data;
234 spi_xfer(enc->slave, 2 * 8, dout, NULL,
235 SPI_XFER_BEGIN | SPI_XFER_END);
236 readback = enc_r8(enc, reg);
237 if (readback == data)
238 break;
239 /* wait 1ms */
240 udelay(1000);
241 }
242 if (i == c) {
243 printf("%s: write reg 0x%03x failed\n", enc->dev->name, reg);
244 }
245}
246
247/*
248 * Read ENC RAM into buffer
249 */
250static void enc_rbuf(enc_dev_t *enc, const u16 length, u8 *buf)
251{
252 u8 dout[1];
253
254 dout[0] = CMD_RBM;
255 spi_xfer(enc->slave, 8, dout, NULL, SPI_XFER_BEGIN);
256 spi_xfer(enc->slave, length * 8, NULL, buf, SPI_XFER_END);
257#ifdef DEBUG
258 puts("Rx:\n");
259 print_buffer(0, buf, 1, length, 0);
260#endif
261}
262
263/*
264 * Write buffer into ENC RAM
265 */
266static void enc_wbuf(enc_dev_t *enc, const u16 length, const u8 *buf, const u8 control)
267{
268 u8 dout[2];
269 dout[0] = CMD_WBM;
270 dout[1] = control;
271 spi_xfer(enc->slave, 2 * 8, dout, NULL, SPI_XFER_BEGIN);
272 spi_xfer(enc->slave, length * 8, buf, NULL, SPI_XFER_END);
273#ifdef DEBUG
274 puts("Tx:\n");
275 print_buffer(0, buf, 1, length, 0);
276#endif
277}
278
279/*
280 * Try to claim the SPI bus.
281 * Print error message on failure.
282 */
283static int enc_claim_bus(enc_dev_t *enc)
284{
285 int rc = spi_claim_bus(enc->slave);
286 if (rc)
287 printf("%s: failed to claim SPI bus\n", enc->dev->name);
288 return rc;
289}
290
291/*
292 * Release previously claimed SPI bus.
293 * This function is mainly for symmetry to enc_claim_bus().
294 * Let the toolchain decide to inline it...
295 */
296static void enc_release_bus(enc_dev_t *enc)
297{
298 spi_release_bus(enc->slave);
299}
300
301/*
302 * Read PHY register
303 */
Andy Fleming09c04c22011-03-22 22:49:13 -0500304static u16 enc_phy_read(enc_dev_t *enc, const u8 addr)
Reinhard Meyera61a8192010-09-12 16:23:49 +0200305{
306 uint64_t etime;
307 u8 status;
308
309 enc_w8(enc, CTL_REG_MIREGADR, addr);
310 enc_w8(enc, CTL_REG_MICMD, ENC_MICMD_MIIRD);
311 /* 1 second timeout - only happens on hardware problem */
312 etime = get_ticks() + get_tbclk();
313 /* poll MISTAT.BUSY bit until operation is complete */
314 do
315 {
316 status = enc_r8(enc, CTL_REG_MISTAT);
317 } while (get_ticks() <= etime && (status & ENC_MISTAT_BUSY));
318 if (status & ENC_MISTAT_BUSY) {
319 printf("%s: timeout reading phy\n", enc->dev->name);
320 return 0;
321 }
322 enc_w8(enc, CTL_REG_MICMD, 0);
323 return enc_r16(enc, CTL_REG_MIRDL);
324}
325
326/*
327 * Write PHY register
328 */
Andy Fleming09c04c22011-03-22 22:49:13 -0500329static void enc_phy_write(enc_dev_t *enc, const u8 addr, const u16 data)
Reinhard Meyera61a8192010-09-12 16:23:49 +0200330{
331 uint64_t etime;
332 u8 status;
333
334 enc_w8(enc, CTL_REG_MIREGADR, addr);
335 enc_w16(enc, CTL_REG_MIWRL, data);
336 /* 1 second timeout - only happens on hardware problem */
337 etime = get_ticks() + get_tbclk();
338 /* poll MISTAT.BUSY bit until operation is complete */
339 do
340 {
341 status = enc_r8(enc, CTL_REG_MISTAT);
342 } while (get_ticks() <= etime && (status & ENC_MISTAT_BUSY));
343 if (status & ENC_MISTAT_BUSY) {
344 printf("%s: timeout writing phy\n", enc->dev->name);
345 return;
346 }
347}
348
349/*
350 * Verify link status, wait if necessary
351 *
352 * Note: with a 10 MBit/s only PHY there is no autonegotiation possible,
353 * half/full duplex is a pure setup matter. For the time being, this driver
354 * will setup in half duplex mode only.
355 */
356static int enc_phy_link_wait(enc_dev_t *enc)
357{
358 u16 status;
359 int duplex;
360 uint64_t etime;
361
362#ifdef CONFIG_ENC_SILENTLINK
363 /* check if we have a link, then just return */
Andy Fleming09c04c22011-03-22 22:49:13 -0500364 status = enc_phy_read(enc, PHY_REG_PHSTAT1);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200365 if (status & ENC_PHSTAT1_LLSTAT)
366 return 0;
367#endif
368
369 /* wait for link with 1 second timeout */
370 etime = get_ticks() + get_tbclk();
371 while (get_ticks() <= etime) {
Andy Fleming09c04c22011-03-22 22:49:13 -0500372 status = enc_phy_read(enc, PHY_REG_PHSTAT1);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200373 if (status & ENC_PHSTAT1_LLSTAT) {
374 /* now we have a link */
Andy Fleming09c04c22011-03-22 22:49:13 -0500375 status = enc_phy_read(enc, PHY_REG_PHSTAT2);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200376 duplex = (status & ENC_PHSTAT2_DPXSTAT) ? 1 : 0;
377 printf("%s: link up, 10Mbps %s-duplex\n",
378 enc->dev->name, duplex ? "full" : "half");
379 return 0;
380 }
381 udelay(1000);
382 }
383
Vagrant Cascadianeae4b2b2016-04-30 19:18:00 -0700384 /* timeout occurred */
Reinhard Meyera61a8192010-09-12 16:23:49 +0200385 printf("%s: link down\n", enc->dev->name);
386 return 1;
387}
388
389/*
390 * This function resets the receiver only.
391 */
392static void enc_reset_rx(enc_dev_t *enc)
393{
394 u8 econ1;
395
396 econ1 = enc_r8(enc, CTL_REG_ECON1);
397 if ((econ1 & ENC_ECON1_RXRST) == 0) {
398 enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_RXRST);
399 enc->rx_reset_counter = RX_RESET_COUNTER;
400 }
401}
402
403/*
404 * Reset receiver and reenable it.
405 */
406static void enc_reset_rx_call(enc_dev_t *enc)
407{
408 enc_bclr(enc, CTL_REG_ECON1, ENC_ECON1_RXRST);
409 enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_RXEN);
410}
411
412/*
413 * Copy a packet from the receive ring and forward it to
414 * the protocol stack.
415 */
416static void enc_receive(enc_dev_t *enc)
417{
Joe Hershberger1fd92db2015-04-08 01:41:06 -0500418 u8 *packet = (u8 *)net_rx_packets[0];
Reinhard Meyera61a8192010-09-12 16:23:49 +0200419 u16 pkt_len;
420 u16 copy_len;
421 u16 status;
Reinhard Meyera61a8192010-09-12 16:23:49 +0200422 u8 pkt_cnt = 0;
423 u16 rxbuf_rdpt;
424 u8 hbuf[6];
425
426 enc_w16(enc, CTL_REG_ERDPTL, enc->next_pointer);
427 do {
428 enc_rbuf(enc, 6, hbuf);
429 enc->next_pointer = hbuf[0] | (hbuf[1] << 8);
430 pkt_len = hbuf[2] | (hbuf[3] << 8);
431 status = hbuf[4] | (hbuf[5] << 8);
432 debug("next_pointer=$%04x pkt_len=%u status=$%04x\n",
433 enc->next_pointer, pkt_len, status);
434 if (pkt_len <= ENC_MAX_FRM_LEN)
435 copy_len = pkt_len;
436 else
437 copy_len = 0;
438 if ((status & (1L << 7)) == 0) /* check Received Ok bit */
439 copy_len = 0;
440 /* check if next pointer is resonable */
441 if (enc->next_pointer >= ENC_TX_BUF_START)
442 copy_len = 0;
443 if (copy_len > 0) {
444 enc_rbuf(enc, copy_len, packet);
445 }
446 /* advance read pointer to next pointer */
447 enc_w16(enc, CTL_REG_ERDPTL, enc->next_pointer);
448 /* decrease packet counter */
449 enc_bset(enc, CTL_REG_ECON2, ENC_ECON2_PKTDEC);
450 /*
451 * Only odd values should be written to ERXRDPTL,
452 * see errata B4 pt.13
453 */
454 rxbuf_rdpt = enc->next_pointer - 1;
455 if ((rxbuf_rdpt < enc_r16(enc, CTL_REG_ERXSTL)) ||
456 (rxbuf_rdpt > enc_r16(enc, CTL_REG_ERXNDL))) {
457 enc_w16(enc, CTL_REG_ERXRDPTL,
458 enc_r16(enc, CTL_REG_ERXNDL));
459 } else {
460 enc_w16(enc, CTL_REG_ERXRDPTL, rxbuf_rdpt);
461 }
462 /* read pktcnt */
463 pkt_cnt = enc_r8(enc, CTL_REG_EPKTCNT);
464 if (copy_len == 0) {
Anatolij Gustschinda540662011-11-15 13:20:55 +0000465 (void)enc_r8(enc, CTL_REG_EIR);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200466 enc_reset_rx(enc);
467 printf("%s: receive copy_len=0\n", enc->dev->name);
468 continue;
469 }
470 /*
Joe Hershberger1fd92db2015-04-08 01:41:06 -0500471 * Because net_process_received_packet() might call enc_send(),
472 * we need to release the SPI bus, call
473 * net_process_received_packet(), reclaim the bus.
Reinhard Meyera61a8192010-09-12 16:23:49 +0200474 */
475 enc_release_bus(enc);
Joe Hershberger1fd92db2015-04-08 01:41:06 -0500476 net_process_received_packet(packet, pkt_len);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200477 if (enc_claim_bus(enc))
478 return;
Anatolij Gustschinda540662011-11-15 13:20:55 +0000479 (void)enc_r8(enc, CTL_REG_EIR);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200480 } while (pkt_cnt);
481 /* Use EPKTCNT not EIR.PKTIF flag, see errata pt. 6 */
482}
483
484/*
485 * Poll for completely received packets.
486 */
487static void enc_poll(enc_dev_t *enc)
488{
489 u8 eir_reg;
Reinhard Meyera61a8192010-09-12 16:23:49 +0200490 u8 pkt_cnt;
491
Anatolij Gustschinda540662011-11-15 13:20:55 +0000492 (void)enc_r8(enc, CTL_REG_ESTAT);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200493 eir_reg = enc_r8(enc, CTL_REG_EIR);
494 if (eir_reg & ENC_EIR_TXIF) {
495 /* clear TXIF bit in EIR */
496 enc_bclr(enc, CTL_REG_EIR, ENC_EIR_TXIF);
497 }
498 /* We have to use pktcnt and not pktif bit, see errata pt. 6 */
499 pkt_cnt = enc_r8(enc, CTL_REG_EPKTCNT);
500 if (pkt_cnt > 0) {
501 if ((eir_reg & ENC_EIR_PKTIF) == 0) {
502 debug("enc_poll: pkt cnt > 0, but pktif not set\n");
503 }
504 enc_receive(enc);
505 /*
506 * clear PKTIF bit in EIR, this should not need to be done
507 * but it seems like we get problems if we do not
508 */
509 enc_bclr(enc, CTL_REG_EIR, ENC_EIR_PKTIF);
510 }
511 if (eir_reg & ENC_EIR_RXERIF) {
512 printf("%s: rx error\n", enc->dev->name);
513 enc_bclr(enc, CTL_REG_EIR, ENC_EIR_RXERIF);
514 }
515 if (eir_reg & ENC_EIR_TXERIF) {
516 printf("%s: tx error\n", enc->dev->name);
517 enc_bclr(enc, CTL_REG_EIR, ENC_EIR_TXERIF);
518 }
Reinhard Meyera61a8192010-09-12 16:23:49 +0200519}
520
521/*
522 * Completely Reset the ENC
523 */
524static void enc_reset(enc_dev_t *enc)
525{
526 u8 dout[1];
527
528 dout[0] = CMD_SRC;
529 spi_xfer(enc->slave, 8, dout, NULL,
530 SPI_XFER_BEGIN | SPI_XFER_END);
531 /* sleep 1 ms. See errata pt. 2 */
532 udelay(1000);
533}
534
535/*
536 * Initialisation data for most of the ENC registers
537 */
538static const u16 enc_initdata[] = {
539 /*
540 * Setup the buffer space. The reset values are valid for the
541 * other pointers.
542 *
543 * We shall not write to ERXST, see errata pt. 5. Instead we
544 * have to make sure that ENC_RX_BUS_START is 0.
545 */
546 CTL_REG_ERXSTL, ENC_RX_BUF_START,
547 CTL_REG_ERXSTH, ENC_RX_BUF_START >> 8,
548 CTL_REG_ERXNDL, ENC_RX_BUF_END,
549 CTL_REG_ERXNDH, ENC_RX_BUF_END >> 8,
550 CTL_REG_ERDPTL, ENC_RX_BUF_START,
551 CTL_REG_ERDPTH, ENC_RX_BUF_START >> 8,
552 /*
553 * Set the filter to receive only good-CRC, unicast and broadcast
554 * frames.
555 * Note: some DHCP servers return their answers as broadcasts!
556 * So its unwise to remove broadcast from this. This driver
557 * might incur receiver overruns with packet loss on a broadcast
558 * flooded network.
559 */
560 CTL_REG_ERXFCON, ENC_RFR_BCEN | ENC_RFR_UCEN | ENC_RFR_CRCEN,
561
562 /* enable MAC to receive frames */
563 CTL_REG_MACON1,
564 ENC_MACON1_MARXEN | ENC_MACON1_TXPAUS | ENC_MACON1_RXPAUS,
565
566 /* configure pad, tx-crc and duplex */
567 CTL_REG_MACON3,
568 ENC_MACON3_PADCFG0 | ENC_MACON3_TXCRCEN |
569 ENC_MACON3_FRMLNEN,
570
571 /* Allow infinite deferals if the medium is continously busy */
572 CTL_REG_MACON4, ENC_MACON4_DEFER,
573
574 /* Late collisions occur beyond 63 bytes */
575 CTL_REG_MACLCON2, 63,
576
577 /*
578 * Set (low byte) Non-Back-to_Back Inter-Packet Gap.
579 * Recommended 0x12
580 */
581 CTL_REG_MAIPGL, 0x12,
582
583 /*
584 * Set (high byte) Non-Back-to_Back Inter-Packet Gap.
585 * Recommended 0x0c for half-duplex. Nothing for full-duplex
586 */
587 CTL_REG_MAIPGH, 0x0C,
588
589 /* set maximum frame length */
590 CTL_REG_MAMXFLL, ENC_MAX_FRM_LEN,
591 CTL_REG_MAMXFLH, ENC_MAX_FRM_LEN >> 8,
592
593 /*
594 * Set MAC back-to-back inter-packet gap.
595 * Recommended 0x12 for half duplex
596 * and 0x15 for full duplex.
597 */
598 CTL_REG_MABBIPG, 0x12,
599
600 /* end of table */
601 0xffff
602};
603
604/*
605 * Wait for the XTAL oscillator to become ready
606 */
607static int enc_clock_wait(enc_dev_t *enc)
608{
609 uint64_t etime;
610
611 /* one second timeout */
612 etime = get_ticks() + get_tbclk();
613
614 /*
615 * Wait for CLKRDY to become set (i.e., check that we can
616 * communicate with the ENC)
617 */
618 do
619 {
620 if (enc_r8(enc, CTL_REG_ESTAT) & ENC_ESTAT_CLKRDY)
621 return 0;
622 } while (get_ticks() <= etime);
623
624 printf("%s: timeout waiting for CLKRDY\n", enc->dev->name);
625 return -1;
626}
627
628/*
629 * Write the MAC address into the ENC
630 */
631static int enc_write_macaddr(enc_dev_t *enc)
632{
633 unsigned char *p = enc->dev->enetaddr;
634
635 enc_w8_retry(enc, CTL_REG_MAADR5, *p++, 5);
636 enc_w8_retry(enc, CTL_REG_MAADR4, *p++, 5);
637 enc_w8_retry(enc, CTL_REG_MAADR3, *p++, 5);
638 enc_w8_retry(enc, CTL_REG_MAADR2, *p++, 5);
639 enc_w8_retry(enc, CTL_REG_MAADR1, *p++, 5);
640 enc_w8_retry(enc, CTL_REG_MAADR0, *p, 5);
641 return 0;
642}
643
644/*
645 * Setup most of the ENC registers
646 */
647static int enc_setup(enc_dev_t *enc)
648{
649 u16 phid1 = 0;
650 u16 phid2 = 0;
651 const u16 *tp;
652
653 /* reset enc struct values */
654 enc->next_pointer = ENC_RX_BUF_START;
655 enc->rx_reset_counter = RX_RESET_COUNTER;
656 enc->bank = 0xff; /* invalidate current bank in enc28j60 */
657
658 /* verify PHY identification */
Andy Fleming09c04c22011-03-22 22:49:13 -0500659 phid1 = enc_phy_read(enc, PHY_REG_PHID1);
660 phid2 = enc_phy_read(enc, PHY_REG_PHID2) & ENC_PHID2_MASK;
Reinhard Meyera61a8192010-09-12 16:23:49 +0200661 if (phid1 != ENC_PHID1_VALUE || phid2 != ENC_PHID2_VALUE) {
662 printf("%s: failed to identify PHY. Found %04x:%04x\n",
663 enc->dev->name, phid1, phid2);
664 return -1;
665 }
666
667 /* now program registers */
668 for (tp = enc_initdata; *tp != 0xffff; tp += 2)
669 enc_w8_retry(enc, tp[0], tp[1], 10);
670
671 /*
672 * Prevent automatic loopback of data beeing transmitted by setting
673 * ENC_PHCON2_HDLDIS
674 */
Andy Fleming09c04c22011-03-22 22:49:13 -0500675 enc_phy_write(enc, PHY_REG_PHCON2, (1<<8));
Reinhard Meyera61a8192010-09-12 16:23:49 +0200676
677 /*
678 * LEDs configuration
679 * LEDA: LACFG = 0100 -> display link status
680 * LEDB: LBCFG = 0111 -> display TX & RX activity
681 * STRCH = 1 -> LED pulses
682 */
Andy Fleming09c04c22011-03-22 22:49:13 -0500683 enc_phy_write(enc, PHY_REG_PHLCON, 0x0472);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200684
685 /* Reset PDPXMD-bit => half duplex */
Andy Fleming09c04c22011-03-22 22:49:13 -0500686 enc_phy_write(enc, PHY_REG_PHCON1, 0);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200687
Reinhard Meyera61a8192010-09-12 16:23:49 +0200688 return 0;
689}
690
691/*
692 * Check if ENC has been initialized.
693 * If not, try to initialize it.
694 * Remember initialized state in struct.
695 */
696static int enc_initcheck(enc_dev_t *enc, const enum enc_initstate requiredstate)
697{
698 if (enc->initstate >= requiredstate)
699 return 0;
700
701 if (enc->initstate < setupdone) {
702 /* Initialize the ENC only */
703 enc_reset(enc);
704 /* if any of functions fails, skip the rest and return an error */
705 if (enc_clock_wait(enc) || enc_setup(enc) || enc_write_macaddr(enc)) {
706 return -1;
707 }
708 enc->initstate = setupdone;
709 }
710 /* if that's all we need, return here */
711 if (enc->initstate >= requiredstate)
712 return 0;
713
714 /* now wait for link ready condition */
715 if (enc_phy_link_wait(enc)) {
716 return -1;
717 }
718 enc->initstate = linkready;
719 return 0;
720}
721
722#if defined(CONFIG_CMD_MII)
723/*
724 * Read a PHY register.
725 *
726 * This function is registered with miiphy_register().
727 */
Joe Hershberger5a49f172016-08-08 11:28:38 -0500728int enc_miiphy_read(struct mii_dev *bus, int phy_adr, int devad, int reg)
Reinhard Meyera61a8192010-09-12 16:23:49 +0200729{
Joe Hershberger5a49f172016-08-08 11:28:38 -0500730 u16 value = 0;
731 struct eth_device *dev = eth_get_dev_by_name(bus->name);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200732 enc_dev_t *enc;
733
734 if (!dev || phy_adr != 0)
735 return -1;
736
737 enc = dev->priv;
738 if (enc_claim_bus(enc))
739 return -1;
740 if (enc_initcheck(enc, setupdone)) {
741 enc_release_bus(enc);
742 return -1;
743 }
Joe Hershberger5a49f172016-08-08 11:28:38 -0500744 value = enc_phy_read(enc, reg);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200745 enc_release_bus(enc);
Joe Hershberger5a49f172016-08-08 11:28:38 -0500746 return value;
Reinhard Meyera61a8192010-09-12 16:23:49 +0200747}
748
749/*
750 * Write a PHY register.
751 *
752 * This function is registered with miiphy_register().
753 */
Joe Hershberger5a49f172016-08-08 11:28:38 -0500754int enc_miiphy_write(struct mii_dev *bus, int phy_adr, int devad, int reg,
755 u16 value)
Reinhard Meyera61a8192010-09-12 16:23:49 +0200756{
Joe Hershberger5a49f172016-08-08 11:28:38 -0500757 struct eth_device *dev = eth_get_dev_by_name(bus->name);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200758 enc_dev_t *enc;
759
760 if (!dev || phy_adr != 0)
761 return -1;
762
763 enc = dev->priv;
764 if (enc_claim_bus(enc))
765 return -1;
766 if (enc_initcheck(enc, setupdone)) {
767 enc_release_bus(enc);
768 return -1;
769 }
Andy Fleming09c04c22011-03-22 22:49:13 -0500770 enc_phy_write(enc, reg, value);
Reinhard Meyera61a8192010-09-12 16:23:49 +0200771 enc_release_bus(enc);
772 return 0;
773}
774#endif
775
776/*
777 * Write hardware (MAC) address.
778 *
779 * This function entered into eth_device structure.
780 */
781static int enc_write_hwaddr(struct eth_device *dev)
782{
783 enc_dev_t *enc = dev->priv;
784
785 if (enc_claim_bus(enc))
786 return -1;
787 if (enc_initcheck(enc, setupdone)) {
788 enc_release_bus(enc);
789 return -1;
790 }
791 enc_release_bus(enc);
792 return 0;
793}
794
795/*
796 * Initialize ENC28J60 for use.
797 *
798 * This function entered into eth_device structure.
799 */
800static int enc_init(struct eth_device *dev, bd_t *bis)
801{
802 enc_dev_t *enc = dev->priv;
803
804 if (enc_claim_bus(enc))
805 return -1;
806 if (enc_initcheck(enc, linkready)) {
807 enc_release_bus(enc);
808 return -1;
809 }
810 /* enable receive */
811 enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_RXEN);
812 enc_release_bus(enc);
813 return 0;
814}
815
816/*
817 * Check for received packets.
818 *
819 * This function entered into eth_device structure.
820 */
821static int enc_recv(struct eth_device *dev)
822{
823 enc_dev_t *enc = dev->priv;
824
825 if (enc_claim_bus(enc))
826 return -1;
827 if (enc_initcheck(enc, linkready)) {
828 enc_release_bus(enc);
829 return -1;
830 }
831 /* Check for dead receiver */
832 if (enc->rx_reset_counter > 0)
833 enc->rx_reset_counter--;
834 else
835 enc_reset_rx_call(enc);
836 enc_poll(enc);
837 enc_release_bus(enc);
838 return 0;
839}
840
841/*
842 * Send a packet.
843 *
844 * This function entered into eth_device structure.
845 *
846 * Should we wait here until we have a Link? Or shall we leave that to
847 * protocol retries?
848 */
849static int enc_send(
850 struct eth_device *dev,
Joe Hershbergerb58cab32012-05-21 14:45:26 +0000851 void *packet,
Reinhard Meyera61a8192010-09-12 16:23:49 +0200852 int length)
853{
854 enc_dev_t *enc = dev->priv;
855
856 if (enc_claim_bus(enc))
857 return -1;
858 if (enc_initcheck(enc, linkready)) {
859 enc_release_bus(enc);
860 return -1;
861 }
862 /* setup transmit pointers */
863 enc_w16(enc, CTL_REG_EWRPTL, ENC_TX_BUF_START);
864 enc_w16(enc, CTL_REG_ETXNDL, length + ENC_TX_BUF_START);
865 enc_w16(enc, CTL_REG_ETXSTL, ENC_TX_BUF_START);
866 /* write packet to ENC */
867 enc_wbuf(enc, length, (u8 *) packet, 0x00);
868 /*
869 * Check that the internal transmit logic has not been altered
870 * by excessive collisions. Reset transmitter if so.
871 * See Errata B4 12 and 14.
872 */
873 if (enc_r8(enc, CTL_REG_EIR) & ENC_EIR_TXERIF) {
874 enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_TXRST);
875 enc_bclr(enc, CTL_REG_ECON1, ENC_ECON1_TXRST);
876 }
877 enc_bclr(enc, CTL_REG_EIR, (ENC_EIR_TXERIF | ENC_EIR_TXIF));
878 /* start transmitting */
879 enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_TXRTS);
880 enc_release_bus(enc);
881 return 0;
882}
883
884/*
885 * Finish use of ENC.
886 *
887 * This function entered into eth_device structure.
888 */
889static void enc_halt(struct eth_device *dev)
890{
891 enc_dev_t *enc = dev->priv;
892
893 if (enc_claim_bus(enc))
894 return;
895 /* Just disable receiver */
896 enc_bclr(enc, CTL_REG_ECON1, ENC_ECON1_RXEN);
897 enc_release_bus(enc);
898}
899
900/*
901 * This is the only exported function.
902 *
903 * It may be called several times with different bus:cs combinations.
904 */
905int enc28j60_initialize(unsigned int bus, unsigned int cs,
906 unsigned int max_hz, unsigned int mode)
907{
908 struct eth_device *dev;
909 enc_dev_t *enc;
910
911 /* try to allocate, check and clear eth_device object */
912 dev = malloc(sizeof(*dev));
913 if (!dev) {
914 return -1;
915 }
916 memset(dev, 0, sizeof(*dev));
917
918 /* try to allocate, check and clear enc_dev_t object */
919 enc = malloc(sizeof(*enc));
920 if (!enc) {
921 free(dev);
922 return -1;
923 }
924 memset(enc, 0, sizeof(*enc));
925
926 /* try to setup the SPI slave */
927 enc->slave = spi_setup_slave(bus, cs, max_hz, mode);
928 if (!enc->slave) {
929 printf("enc28j60: invalid SPI device %i:%i\n", bus, cs);
930 free(enc);
931 free(dev);
932 return -1;
933 }
934
935 enc->dev = dev;
936 /* now fill the eth_device object */
937 dev->priv = enc;
938 dev->init = enc_init;
939 dev->halt = enc_halt;
940 dev->send = enc_send;
941 dev->recv = enc_recv;
942 dev->write_hwaddr = enc_write_hwaddr;
943 sprintf(dev->name, "enc%i.%i", bus, cs);
944 eth_register(dev);
945#if defined(CONFIG_CMD_MII)
Joe Hershberger5a49f172016-08-08 11:28:38 -0500946 int retval;
947 struct mii_dev *mdiodev = mdio_alloc();
948 if (!mdiodev)
949 return -ENOMEM;
950 strncpy(mdiodev->name, dev->name, MDIO_NAME_LEN);
951 mdiodev->read = enc_miiphy_read;
952 mdiodev->write = enc_miiphy_write;
953
954 retval = mdio_register(mdiodev);
955 if (retval < 0)
956 return retval;
Reinhard Meyera61a8192010-09-12 16:23:49 +0200957#endif
958 return 0;
959}