arch/blackfin/include/asm/config.h

/*
 * config.h - setup common defines for Blackfin boards based on config.h
 *
 * Copyright (c) 2007-2009 Analog Devices Inc.
 *
 * Licensed under the GPL-2 or later.
 */

#ifndef __ASM_BLACKFIN_CONFIG_POST_H__
#define __ASM_BLACKFIN_CONFIG_POST_H__

/* Some of our defines use this (like CONFIG_SYS_GBL_DATA_ADDR) */
#include <asm-offsets.h>

/* Sanity check CONFIG_BFIN_CPU */
#ifndef CONFIG_BFIN_CPU
# error CONFIG_BFIN_CPU: your board config needs to define this
#endif

#ifndef CONFIG_BFIN_SCRATCH_REG
# define CONFIG_BFIN_SCRATCH_REG retn
#endif

/* U-Boot wants this config name */
#define CONFIG_SYS_CACHELINE_SIZE L1_CACHE_BYTES

/* Make sure the structure is properly aligned */
#if ((CONFIG_SYS_GBL_DATA_ADDR & -4) != CONFIG_SYS_GBL_DATA_ADDR)
# error CONFIG_SYS_GBL_DATA_ADDR: must be 4 byte aligned
#endif

/* Set default CONFIG_VCO_HZ if need be */
#if !defined(CONFIG_VCO_HZ)
# if (CONFIG_CLKIN_HALF == 0)
#  define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
# else
#  define CONFIG_VCO_HZ ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT) / 2)
# endif
#endif

/* Set default CONFIG_CCLK_HZ if need be */
#if !defined(CONFIG_CCLK_HZ)
# if (CONFIG_PLL_BYPASS == 0)
#  define CONFIG_CCLK_HZ (CONFIG_VCO_HZ / CONFIG_CCLK_DIV)
# else
#  define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
# endif
#endif

/* Set default CONFIG_SCLK_HZ if need be */
#if !defined(CONFIG_SCLK_HZ)
# if (CONFIG_PLL_BYPASS == 0)
#  define CONFIG_SCLK_HZ (CONFIG_VCO_HZ / CONFIG_SCLK_DIV)
# else
#  define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
# endif
#endif

/* Since we use these to program PLL registers directly,
 * make sure the values are sane and won't screw us up.
 */
#if (CONFIG_VCO_MULT & 0x3F) != CONFIG_VCO_MULT
# error CONFIG_VCO_MULT: Invalid value: must fit in 6 bits (0 - 63)
#endif
#if (CONFIG_CLKIN_HALF & 0x1) != CONFIG_CLKIN_HALF
# error CONFIG_CLKIN_HALF: Invalid value: must be 0 or 1
#endif
#if (CONFIG_PLL_BYPASS & 0x1) != CONFIG_PLL_BYPASS
# error CONFIG_PLL_BYPASS: Invalid value: must be 0 or 1
#endif

/* If we are using KGDB, make sure we defer exceptions */
#ifdef CONFIG_CMD_KGDB
# define CONFIG_EXCEPTION_DEFER	1
#endif

/* Using L1 scratch pad makes sense for everyone by default. */
#ifndef CONFIG_LINUX_CMDLINE_ADDR
# define CONFIG_LINUX_CMDLINE_ADDR L1_SRAM_SCRATCH
#endif
#ifndef CONFIG_LINUX_CMDLINE_SIZE
# define CONFIG_LINUX_CMDLINE_SIZE L1_SRAM_SCRATCH_SIZE
#endif

/* Set default SPI flash CS to the one we boot from */
#if defined(CONFIG_ENV_IS_IN_SPI_FLASH) && !defined(CONFIG_ENV_SPI_CS)
# define CONFIG_ENV_SPI_CS BFIN_BOOT_SPI_SSEL
#endif

/* We need envcrc to embed the env into LDRs */
#ifdef CONFIG_ENV_IS_EMBEDDED_IN_LDR
# define CONFIG_BUILD_ENVCRC
#endif

/* Default/common Blackfin memory layout */
#ifndef CONFIG_SYS_SDRAM_BASE
# define CONFIG_SYS_SDRAM_BASE 0
#endif
#ifndef CONFIG_SYS_MAX_RAM_SIZE
# define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
#endif
#ifndef CONFIG_SYS_MONITOR_BASE
# if CONFIG_SYS_MAX_RAM_SIZE
#  define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN)
# else
#  define CONFIG_SYS_MONITOR_BASE 0
# endif
#endif
#ifndef CONFIG_SYS_MALLOC_BASE
# define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
#endif
#ifndef CONFIG_STACKBASE
# define CONFIG_STACKBASE (CONFIG_SYS_MALLOC_BASE - 4)
#endif
#ifndef CONFIG_SYS_MEMTEST_START
# define CONFIG_SYS_MEMTEST_START 0
#endif
#ifndef CONFIG_SYS_MEMTEST_END
# define CONFIG_SYS_MEMTEST_END (CONFIG_STACKBASE - 8192 + 4)
#endif
#ifndef CONFIG_SYS_POST_WORD_ADDR
# define CONFIG_SYS_POST_WORD_ADDR (L1_DATA_B_SRAM + L1_DATA_B_SRAM_SIZE - 4)
#endif

/* Check to make sure everything fits in external RAM */
#if CONFIG_SYS_MAX_RAM_SIZE && \
    ((CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) > CONFIG_SYS_MAX_RAM_SIZE)
# error Memory Map does not fit into configuration
#endif

/* Default/common Blackfin environment settings */
#ifndef CONFIG_LOADADDR
# define CONFIG_LOADADDR 0x1000000
#endif
#ifndef CONFIG_SYS_LOAD_ADDR
# define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#endif
#ifndef CONFIG_SYS_BOOTM_LEN
# define CONFIG_SYS_BOOTM_LEN 0x4000000
#endif
#ifndef CONFIG_SYS_CBSIZE
# define CONFIG_SYS_CBSIZE 1024
#elif defined(CONFIG_CMD_KGDB) && CONFIG_SYS_CBSIZE < 1024
# error "kgdb needs cbsize to be >= 1024"
#endif
#ifndef CONFIG_SYS_BARGSIZE
# define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#endif
#ifndef CONFIG_SYS_PBSIZE
# define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#endif
#ifndef CONFIG_SYS_MAXARGS
# define CONFIG_SYS_MAXARGS 16
#endif

/* Blackfin POST tests */
#ifdef CONFIG_POST_BSPEC1_GPIO_LEDS
# define CONFIG_POST_BSPEC1 \
	{ \
		"LED test", "led", "This test verifies LEDs on the board.", \
		POST_MEM | POST_ALWAYS, &led_post_test, NULL, NULL, \
		CONFIG_SYS_POST_BSPEC1, \
	}
#endif
#ifdef CONFIG_POST_BSPEC2_GPIO_BUTTONS
# define CONFIG_POST_BSPEC2 \
	{ \
		"Button test", "button", "This test verifies buttons on the board.", \
		POST_MEM | POST_ALWAYS, &button_post_test, NULL, NULL, \
		CONFIG_SYS_POST_BSPEC2, \
	}
#endif

#define CONFIG_ARCH_MISC_INIT

#define CONFIG_CPU CONFIG_BFIN_CPU

#endif