blob: bdedef5374f959ec74f7bb4e5c86b0945aeff268 [file] [log] [blame]
Oleksandr G Zhadan8b0044f2015-04-29 16:57:39 -04001/*
2 * Copyright 2013-2015 Arcturus Networks, Inc.
3 * http://www.arcturusnetworks.com/products/ucp1020/
4 * based on include/configs/p1_p2_rdb_pc.h
5 * original copyright follows:
6 * Copyright 2009-2011 Freescale Semiconductor, Inc.
7 *
8 * SPDX-License-Identifier: GPL-2.0+
9 */
10
11/*
12 * QorIQ uCP1020-xx boards configuration file
13 */
14#ifndef __CONFIG_H
15#define __CONFIG_H
16
17#define CONFIG_SYS_GENERIC_BOARD
18#define CONFIG_DISPLAY_BOARDINFO
19
20#define CONFIG_FSL_ELBC
21#define CONFIG_PCI
22#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
23#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
24#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
25#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
26#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
27#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
28
29#if defined(CONFIG_TARTGET_UCP1020T1)
30
31#define CONFIG_UCP1020_REV_1_3
32
33#define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
34#define CONFIG_P1020
35
36#define CONFIG_TSEC_ENET
37#define CONFIG_TSEC1
38#define CONFIG_TSEC3
39#define CONFIG_HAS_ETH0
40#define CONFIG_HAS_ETH1
41#define CONFIG_ETHADDR 00:19:D3:FF:FF:FF
42#define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE
43#define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD
44#define CONFIG_IPADDR 10.80.41.229
45#define CONFIG_SERVERIP 10.80.41.227
46#define CONFIG_NETMASK 255.255.252.0
47#define CONFIG_ETHPRIME "eTSEC3"
48
49#ifndef CONFIG_SPI_FLASH
Oleksandr G Zhadan8b0044f2015-04-29 16:57:39 -040050#endif
51#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
52
53#define CONFIG_MMC
54#define CONFIG_SYS_L2_SIZE (256 << 10)
55
56#define CONFIG_LAST_STAGE_INIT
57
58#if !defined(CONFIG_DONGLE)
59#define CONFIG_SILENT_CONSOLE
60#endif
61
62#endif
63
64#if defined(CONFIG_TARGET_UCP1020)
65
66#define CONFIG_UCP1020
67#define CONFIG_UCP1020_REV_1_3
68
69#define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
70#define CONFIG_P1020
71
72#define CONFIG_TSEC_ENET
73#define CONFIG_TSEC1
74#define CONFIG_TSEC2
75#define CONFIG_TSEC3
76#define CONFIG_HAS_ETH0
77#define CONFIG_HAS_ETH1
78#define CONFIG_HAS_ETH2
79#define CONFIG_ETHADDR 00:06:3B:FF:FF:FF
80#define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE
81#define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD
82#define CONFIG_IPADDR 192.168.1.81
83#define CONFIG_IPADDR1 192.168.1.82
84#define CONFIG_IPADDR2 192.168.1.83
85#define CONFIG_SERVERIP 192.168.1.80
86#define CONFIG_GATEWAYIP 102.168.1.1
87#define CONFIG_NETMASK 255.255.255.0
88#define CONFIG_ETHPRIME "eTSEC1"
89
90#ifndef CONFIG_SPI_FLASH
Oleksandr G Zhadan8b0044f2015-04-29 16:57:39 -040091#endif
92#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
93
94#define CONFIG_MMC
95#define CONFIG_SYS_L2_SIZE (256 << 10)
96
97#define CONFIG_LAST_STAGE_INIT
98
99#endif
100
101#ifdef CONFIG_SDCARD
102#define CONFIG_RAMBOOT_SDCARD
103#define CONFIG_SYS_RAMBOOT
104#define CONFIG_SYS_EXTRA_ENV_RELOC
105#define CONFIG_SYS_TEXT_BASE 0x11000000
106#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
107#endif
108
109#ifdef CONFIG_SPIFLASH
110#define CONFIG_RAMBOOT_SPIFLASH
111#define CONFIG_SYS_RAMBOOT
112#define CONFIG_SYS_EXTRA_ENV_RELOC
113#define CONFIG_SYS_TEXT_BASE 0x11000000
114#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
115#endif
116
117#ifndef CONFIG_SYS_TEXT_BASE
118#define CONFIG_SYS_TEXT_BASE 0xeff80000
119#endif
120#define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000
121
122#ifndef CONFIG_RESET_VECTOR_ADDRESS
123#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
124#endif
125
126#ifndef CONFIG_SYS_MONITOR_BASE
127#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
128#endif
129
130/* High Level Configuration Options */
131#define CONFIG_BOOKE
132#define CONFIG_E500
133/* #define CONFIG_MPC85xx */
134
135#define CONFIG_MP
136
137#define CONFIG_FSL_LAW
138
139#define CONFIG_ENV_OVERWRITE
140
141#define CONFIG_CMD_SATA
142#define CONFIG_SATA_SIL
143#define CONFIG_SYS_SATA_MAX_DEVICE 2
144#define CONFIG_LIBATA
145#define CONFIG_LBA48
146
147#define CONFIG_SYS_CLK_FREQ 66666666
148#define CONFIG_DDR_CLK_FREQ 66666666
149
150#define CONFIG_HWCONFIG
151
152#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
153#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */
154#define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */
155/*
156 * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details).
157 * there will be one entry in this array for each two (dummy) sensors in
158 * CONFIG_DTT_SENSORS.
159 *
160 * For uCP1020 module:
161 * - only one ADM1021/NCT72
162 * - i2c addr 0x41
163 * - conversion rate 0x02 = 0.25 conversions/second
164 * - ALERT output disabled
165 * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
166 * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
167 */
168#define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \
169 0x02, 0, 1, 0, 85, 1, 0, 85} }
170
171#define CONFIG_CMD_DTT
172
173/*
174 * These can be toggled for performance analysis, otherwise use default.
175 */
176#define CONFIG_L2_CACHE
177#define CONFIG_BTB
178
179#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
180
181#define CONFIG_ENABLE_36BIT_PHYS
182
183#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
184#define CONFIG_SYS_MEMTEST_END 0x1fffffff
185#define CONFIG_PANIC_HANG /* do not reset board on panic */
186
187#define CONFIG_SYS_CCSRBAR 0xffe00000
188#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
189
190/* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
191 SPL code*/
192#ifdef CONFIG_SPL_BUILD
193#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
194#endif
195
196/* DDR Setup */
197#define CONFIG_DDR_ECC_ENABLE
198#define CONFIG_SYS_FSL_DDR3
199#ifndef CONFIG_DDR_ECC_ENABLE
200#define CONFIG_SYS_DDR_RAW_TIMING
201#define CONFIG_DDR_SPD
202#endif
203#define CONFIG_SYS_SPD_BUS_NUM 1
204#undef CONFIG_FSL_DDR_INTERACTIVE
205
206#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M
207#define CONFIG_CHIP_SELECTS_PER_CTRL 1
208#define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
209#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
210#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
211
212#define CONFIG_NUM_DDR_CONTROLLERS 1
213#define CONFIG_DIMM_SLOTS_PER_CTLR 1
214
215/* Default settings for DDR3 */
216#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
217#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
218#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
219#define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f
220#define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302
221#define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000
222
223#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
224#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
225#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
226#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
227
228#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
229#define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608
230#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
231#define CONFIG_SYS_DDR_RCW_1 0x00000000
232#define CONFIG_SYS_DDR_RCW_2 0x00000000
233#ifdef CONFIG_DDR_ECC_ENABLE
234#define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */
235#else
236#define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */
237#endif
238#define CONFIG_SYS_DDR_CONTROL_2 0x04401050
239#define CONFIG_SYS_DDR_TIMING_4 0x00220001
240#define CONFIG_SYS_DDR_TIMING_5 0x03402400
241
242#define CONFIG_SYS_DDR_TIMING_3 0x00020000
243#define CONFIG_SYS_DDR_TIMING_0 0x00330004
244#define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846
245#define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF
246#define CONFIG_SYS_DDR_CLK_CTRL 0x03000000
247#define CONFIG_SYS_DDR_MODE_1 0x40461520
248#define CONFIG_SYS_DDR_MODE_2 0x8000c000
249#define CONFIG_SYS_DDR_INTERVAL 0x0C300000
250
251#undef CONFIG_CLOCKS_IN_MHZ
252
253/*
254 * Memory map
255 *
256 * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable
257 * 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2)
258 * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1
259 * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable
260 * (early boot only)
261 * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable
262 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable
263 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
264 */
265
266/*
267 * Local Bus Definitions
268 */
269#define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */
270#define CONFIG_SYS_FLASH_BASE 0xec000000
271
272#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
273
274#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
275 | BR_PS_16 | BR_V)
276
277#define CONFIG_FLASH_OR_PRELIM 0xfc000ff7
278
279#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
280#define CONFIG_SYS_FLASH_QUIET_TEST
281#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
282
283#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
284
285#undef CONFIG_SYS_FLASH_CHECKSUM
286#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
287#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
288
289#define CONFIG_FLASH_CFI_DRIVER
290#define CONFIG_SYS_FLASH_CFI
291#define CONFIG_SYS_FLASH_EMPTY_INFO
292#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
293
294#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
295
296#define CONFIG_SYS_INIT_RAM_LOCK
297#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
298/* Initial L1 address */
299#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
300#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
301#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
302/* Size of used area in RAM */
303#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
304
305#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
306 GENERATED_GBL_DATA_SIZE)
307#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
308
309#define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */
310#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */
311
312#define CONFIG_SYS_PMC_BASE 0xff980000
313#define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE
314#define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
315 BR_PS_8 | BR_V)
316#define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
317 OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
318 OR_GPCM_EAD)
319
320#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
321#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
322#ifdef CONFIG_NAND_FSL_ELBC
323#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
324#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
325#endif
326
327/* Serial Port - controlled on board with jumper J8
328 * open - index 2
329 * shorted - index 1
330 */
331#define CONFIG_CONS_INDEX 1
332#undef CONFIG_SERIAL_SOFTWARE_FIFO
333#define CONFIG_SYS_NS16550
334#define CONFIG_SYS_NS16550_SERIAL
335#define CONFIG_SYS_NS16550_REG_SIZE 1
336#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
337#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
338#define CONFIG_NS16550_MIN_FUNCTIONS
339#endif
340
341#define CONFIG_SYS_BAUDRATE_TABLE \
342 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
343
344#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
345#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
346
347/* Use the HUSH parser */
348#define CONFIG_SYS_HUSH_PARSER
349
350/*
351 * Pass open firmware flat tree
352 */
353#define CONFIG_OF_LIBFDT
354#define CONFIG_OF_BOARD_SETUP
355#define CONFIG_OF_STDOUT_VIA_ALIAS
356
357/* new uImage format support */
358#define CONFIG_FIT
359#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
360
361/* I2C */
362#define CONFIG_SYS_I2C
363#define CONFIG_SYS_I2C_FSL
364#define CONFIG_SYS_FSL_I2C_SPEED 400000
365#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
366#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
367#define CONFIG_SYS_FSL_I2C2_SPEED 400000
368#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
369#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
370#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
371#define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */
372
373#define CONFIG_RTC_DS1337
374#define CONFIG_SYS_RTC_DS1337_NOOSC
375#define CONFIG_SYS_I2C_RTC_ADDR 0x68
376#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18
377#define CONFIG_SYS_I2C_NCT72_ADDR 0x4C
378#define CONFIG_SYS_I2C_IDT6V49205B 0x69
379
380/*
381 * eSPI - Enhanced SPI
382 */
383#define CONFIG_HARD_SPI
384#define CONFIG_FSL_ESPI
385
386#define CONFIG_SPI_FLASH_SST 1
387#define CONFIG_SPI_FLASH_STMICRO 1
388#define CONFIG_SPI_FLASH_WINBOND 1
389#define CONFIG_CMD_SF 1
390#define CONFIG_CMD_SPI 1
391#define CONFIG_SF_DEFAULT_SPEED 10000000
392#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
393
394#if defined(CONFIG_PCI)
395/*
396 * General PCI
397 * Memory space is mapped 1-1, but I/O space must start from 0.
398 */
399
400/* controller 2, direct to uli, tgtid 2, Base address 9000 */
401#define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9"
402#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
403#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
404#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
405#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
406#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
407#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
408#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
409#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
410
411/* controller 1, Slot 2, tgtid 1, Base address a000 */
412#define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10"
413#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
414#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
415#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
416#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
417#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000
418#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
419#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000
420#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
421
422#define CONFIG_PCI_PNP /* do pci plug-and-play */
423#define CONFIG_E1000 /* Defind e1000 pci Ethernet card*/
424#define CONFIG_CMD_PCI
Oleksandr G Zhadan8b0044f2015-04-29 16:57:39 -0400425
426#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
427#define CONFIG_DOS_PARTITION
428#endif /* CONFIG_PCI */
429
430/*
431 * Environment
432 */
433#ifdef CONFIG_ENV_FIT_UCBOOT
434
435#define CONFIG_ENV_IS_IN_FLASH
436#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000)
437#define CONFIG_ENV_SIZE 0x20000
438#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
439
440#else
441
442#define CONFIG_ENV_SPI_BUS 0
443#define CONFIG_ENV_SPI_CS 0
444#define CONFIG_ENV_SPI_MAX_HZ 10000000
445#define CONFIG_ENV_SPI_MODE 0
446
447#ifdef CONFIG_RAMBOOT_SPIFLASH
448
449#define CONFIG_ENV_IS_IN_SPI_FLASH
450#define CONFIG_ENV_SIZE 0x3000 /* 12KB */
451#define CONFIG_ENV_OFFSET 0x2000 /* 8KB */
452#define CONFIG_ENV_SECT_SIZE 0x1000
453
454#if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
455/* Address and size of Redundant Environment Sector */
456#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
457#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
458#endif
459
460#elif defined(CONFIG_RAMBOOT_SDCARD)
461#define CONFIG_ENV_IS_IN_MMC
462#define CONFIG_FSL_FIXED_MMC_LOCATION
463#define CONFIG_ENV_SIZE 0x2000
464#define CONFIG_SYS_MMC_ENV_DEV 0
465
466#elif defined(CONFIG_SYS_RAMBOOT)
467#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
468#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
469#define CONFIG_ENV_SIZE 0x2000
470
471#else
472#define CONFIG_ENV_IS_IN_FLASH
473#define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE)
474#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
475#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
476#define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000)
477#if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
478/* Address and size of Redundant Environment Sector */
479#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
480#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
481#endif
482
483#endif
484
485#endif /* CONFIG_ENV_FIT_UCBOOT */
486
487#define CONFIG_LOADS_ECHO /* echo on for serial download */
488#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
489
490/*
491 * Command line configuration.
492 */
Oleksandr G Zhadan8b0044f2015-04-29 16:57:39 -0400493#define CONFIG_CMD_IRQ
494#define CONFIG_CMD_PING
495#define CONFIG_CMD_I2C
496#define CONFIG_CMD_MII
497#define CONFIG_CMD_DATE
498#define CONFIG_CMD_ELF
499#define CONFIG_CMD_I2C
500#define CONFIG_CMD_IRQ
501#define CONFIG_CMD_MII
502#define CONFIG_CMD_PING
Oleksandr G Zhadan8b0044f2015-04-29 16:57:39 -0400503#define CONFIG_CMD_REGINFO
504#define CONFIG_CMD_ERRATA
505#define CONFIG_CMD_CRAMFS
506#define CONFIG_CRAMFS_CMDLINE
507
508/*
509 * USB
510 */
511#define CONFIG_HAS_FSL_DR_USB
512
513#if defined(CONFIG_HAS_FSL_DR_USB)
514#define CONFIG_USB_EHCI
515
516#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
517
518#ifdef CONFIG_USB_EHCI
519#define CONFIG_CMD_USB
520#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
521#define CONFIG_USB_EHCI_FSL
522#define CONFIG_USB_STORAGE
523#endif
524#endif
525
526#undef CONFIG_WATCHDOG /* watchdog disabled */
527
528#ifdef CONFIG_MMC
529#define CONFIG_FSL_ESDHC
530#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
531#define CONFIG_CMD_MMC
532#define CONFIG_MMC_SPI
533#define CONFIG_CMD_MMC_SPI
534#define CONFIG_GENERIC_MMC
535#endif
536
537#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA)
538#define CONFIG_CMD_EXT2
539#define CONFIG_CMD_FAT
540#define CONFIG_DOS_PARTITION
541#endif
542
543/* Misc Extra Settings */
544#define CONFIG_CMD_GPIO 1
545#undef CONFIG_WATCHDOG /* watchdog disabled */
546
547/*
548 * Miscellaneous configurable options
549 */
550#define CONFIG_SYS_LONGHELP /* undef to save memory */
551#define CONFIG_CMDLINE_EDITING /* Command-line editing */
552#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
553#define CONFIG_SYS_PROMPT "B$ " /* Monitor Command Prompt */
554#if defined(CONFIG_CMD_KGDB)
555#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
556#else
557#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
558#endif
559#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
560 /* Print Buffer Size */
561#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
562#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
563#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */
564
565/*
566 * For booting Linux, the board info and command line data
567 * have to be in the first 64 MB of memory, since this is
568 * the maximum mapped by the Linux kernel during initialization.
569 */
570#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/
571#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
572
573#if defined(CONFIG_CMD_KGDB)
574#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
575#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
576#endif
577
578/*
579 * Environment Configuration
580 */
581
582#if defined(CONFIG_TSEC_ENET)
583
584#if defined(CONFIG_UCP1020_REV_1_2)
585#define CONFIG_PHY_MICREL_KSZ9021
586#elif defined(CONFIG_UCP1020_REV_1_3)
587#define CONFIG_PHY_MICREL_KSZ9031
588#else
589#error "UCP1020 module revision is not defined !!!"
590#endif
591
592#define CONFIG_CMD_DHCP
593#define CONFIG_BOOTP_SERVERIP
594
595#define CONFIG_MII /* MII PHY management */
596#define CONFIG_TSEC1_NAME "eTSEC1"
597#define CONFIG_TSEC2_NAME "eTSEC2"
598#define CONFIG_TSEC3_NAME "eTSEC3"
599
600#define TSEC1_PHY_ADDR 4
601#define TSEC2_PHY_ADDR 0
602#define TSEC2_PHY_ADDR_SGMII 0x00
603#define TSEC3_PHY_ADDR 6
604
605#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
606#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
607#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
608
609#define TSEC1_PHYIDX 0
610#define TSEC2_PHYIDX 0
611#define TSEC3_PHYIDX 0
612
613#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
614
615#endif
616
617#define CONFIG_HOSTNAME UCP1020
618#define CONFIG_ROOTPATH "/opt/nfsroot"
619#define CONFIG_BOOTFILE "uImage"
620#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
621
622/* default location for tftp and bootm */
623#define CONFIG_LOADADDR 1000000
624
Oleksandr G Zhadan8b0044f2015-04-29 16:57:39 -0400625#define CONFIG_BOOTARGS /* the boot command will set bootargs */
626
627#define CONFIG_BAUDRATE 115200
628
629#if defined(CONFIG_DONGLE)
630
631#define CONFIG_BOOTDELAY 1 /* autoboot after 1 seconds */
632#define CONFIG_EXTRA_ENV_SETTINGS \
633"bootcmd=run prog_spi_mbrbootcramfs\0" \
634"bootfile=uImage\0" \
635"consoledev=ttyS0\0" \
636"cramfsfile=image.cramfs\0" \
637"dtbaddr=0x00c00000\0" \
638"dtbfile=image.dtb\0" \
639"ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
640"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
641"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
642"fileaddr=0x01000000\0" \
643"filesize=0x00080000\0" \
644"flashmbr=sf probe 0; " \
645 "tftp $loadaddr $mbr; " \
646 "sf erase $mbr_offset +$filesize; " \
647 "sf write $loadaddr $mbr_offset $filesize\0" \
648"flashrecovery=tftp $recoveryaddr $cramfsfile; " \
649 "protect off $nor_recoveryaddr +$filesize; " \
650 "erase $nor_recoveryaddr +$filesize; " \
651 "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \
652 "protect on $nor_recoveryaddr +$filesize\0 " \
653"flashuboot=tftp $ubootaddr $ubootfile; " \
654 "protect off $nor_ubootaddr +$filesize; " \
655 "erase $nor_ubootaddr +$filesize; " \
656 "cp.b $ubootaddr $nor_ubootaddr $filesize; " \
657 "protect on $nor_ubootaddr +$filesize\0 " \
658"flashworking=tftp $workingaddr $cramfsfile; " \
659 "protect off $nor_workingaddr +$filesize; " \
660 "erase $nor_workingaddr +$filesize; " \
661 "cp.b $workingaddr $nor_workingaddr $filesize; " \
662 "protect on $nor_workingaddr +$filesize\0 " \
663"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
664"kerneladdr=0x01100000\0" \
665"kernelfile=uImage\0" \
666"loadaddr=0x01000000\0" \
667"mbr=uCP1020d.mbr\0" \
668"mbr_offset=0x00000000\0" \
669"mmbr=uCP1020Quiet.mbr\0" \
670"mmcpart=0:2\0" \
671"mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \
672 "mmc erase 1 1; " \
673 "mmc write $loadaddr 1 1\0" \
674"mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \
675 "mmc erase 0x40 0x400; " \
676 "mmc write $loadaddr 0x40 0x400\0" \
677"netdev=eth0\0" \
678"nor_recoveryaddr=0xEC0A0000\0" \
679"nor_ubootaddr=0xEFF80000\0" \
680"nor_workingaddr=0xECFA0000\0" \
681"norbootrecovery=setenv bootargs $recoverybootargs" \
682 " console=$consoledev,$baudrate $othbootargs; " \
683 "run norloadrecovery; " \
684 "bootm $kerneladdr - $dtbaddr\0" \
685"norbootworking=setenv bootargs $workingbootargs" \
686 " console=$consoledev,$baudrate $othbootargs; " \
687 "run norloadworking; " \
688 "bootm $kerneladdr - $dtbaddr\0" \
689"norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \
690 "setenv cramfsaddr $nor_recoveryaddr; " \
691 "cramfsload $dtbaddr $dtbfile; " \
692 "cramfsload $kerneladdr $kernelfile\0" \
693"norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \
694 "setenv cramfsaddr $nor_workingaddr; " \
695 "cramfsload $dtbaddr $dtbfile; " \
696 "cramfsload $kerneladdr $kernelfile\0" \
697"prog_spi_mbr=run spi__mbr\0" \
698"prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \
699"prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \
700 "run spi__cramfs\0" \
701"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
702 " console=$consoledev,$baudrate $othbootargs; " \
703 "tftp $rootfsaddr $rootfsfile; " \
704 "tftp $loadaddr $kernelfile; " \
705 "tftp $dtbaddr $dtbfile; " \
706 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \
707"ramdisk_size=120000\0" \
708"ramdiskfile=rootfs.ext2.gz.uboot\0" \
709"recoveryaddr=0x02F00000\0" \
710"recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \
711"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
712 "mw.l 0xffe0f008 0x00400000\0" \
713"rootfsaddr=0x02F00000\0" \
714"rootfsfile=rootfs.ext2.gz.uboot\0" \
715"rootpath=/opt/nfsroot\0" \
716"spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
717 "protect off 0xeC000000 +$filesize; " \
718 "erase 0xEC000000 +$filesize; " \
719 "cp.b $loadaddr 0xEC000000 $filesize; " \
720 "cmp.b $loadaddr 0xEC000000 $filesize; " \
721 "protect on 0xeC000000 +$filesize\0" \
722"spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
723 "protect off 0xeFF80000 +$filesize; " \
724 "erase 0xEFF80000 +$filesize; " \
725 "cp.b $loadaddr 0xEFF80000 $filesize; " \
726 "cmp.b $loadaddr 0xEFF80000 $filesize; " \
727 "protect on 0xeFF80000 +$filesize\0" \
728"spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \
729 "sf probe 0; sf erase 0x8000 +$filesize; " \
730 "sf write $loadaddr 0x8000 $filesize\0" \
731"spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \
732 "protect off 0xec0a0000 +$filesize; " \
733 "erase 0xeC0A0000 +$filesize; " \
734 "cp.b $loadaddr 0xeC0A0000 $filesize; " \
735 "protect on 0xec0a0000 +$filesize\0" \
736"spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \
737 "sf probe 1; sf erase 0 +$filesize; " \
738 "sf write $loadaddr 0 $filesize\0" \
739"spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \
740 "sf probe 0; sf erase 0 +$filesize; " \
741 "sf write $loadaddr 0 $filesize\0" \
742"tftpflash=tftpboot $loadaddr $uboot; " \
743 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
744 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
745 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
746 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
747 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
748"uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
749"ubootaddr=0x01000000\0" \
750"ubootfile=u-boot.bin\0" \
751"ubootd=u-boot4dongle.bin\0" \
752"upgrade=run flashworking\0" \
753"usb_phy_type=ulpi\0 " \
754"workingaddr=0x02F00000\0" \
755"workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
756
757#else
758
759#if defined(CONFIG_UCP1020T1)
760
761#define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */
762#define CONFIG_EXTRA_ENV_SETTINGS \
763"bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \
764"bootfile=uImage\0" \
765"consoledev=ttyS0\0" \
766"cramfsfile=image.cramfs\0" \
767"dtbaddr=0x00c00000\0" \
768"dtbfile=image.dtb\0" \
769"ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
770"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
771"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
772"fileaddr=0x01000000\0" \
773"filesize=0x00080000\0" \
774"flashmbr=sf probe 0; " \
775 "tftp $loadaddr $mbr; " \
776 "sf erase $mbr_offset +$filesize; " \
777 "sf write $loadaddr $mbr_offset $filesize\0" \
778"flashrecovery=tftp $recoveryaddr $cramfsfile; " \
779 "protect off $nor_recoveryaddr +$filesize; " \
780 "erase $nor_recoveryaddr +$filesize; " \
781 "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \
782 "protect on $nor_recoveryaddr +$filesize\0 " \
783"flashuboot=tftp $ubootaddr $ubootfile; " \
784 "protect off $nor_ubootaddr +$filesize; " \
785 "erase $nor_ubootaddr +$filesize; " \
786 "cp.b $ubootaddr $nor_ubootaddr $filesize; " \
787 "protect on $nor_ubootaddr +$filesize\0 " \
788"flashworking=tftp $workingaddr $cramfsfile; " \
789 "protect off $nor_workingaddr +$filesize; " \
790 "erase $nor_workingaddr +$filesize; " \
791 "cp.b $workingaddr $nor_workingaddr $filesize; " \
792 "protect on $nor_workingaddr +$filesize\0 " \
793"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
794"kerneladdr=0x01100000\0" \
795"kernelfile=uImage\0" \
796"loadaddr=0x01000000\0" \
797"mbr=uCP1020.mbr\0" \
798"mbr_offset=0x00000000\0" \
799"netdev=eth0\0" \
800"nor_recoveryaddr=0xEC0A0000\0" \
801"nor_ubootaddr=0xEFF80000\0" \
802"nor_workingaddr=0xECFA0000\0" \
803"norbootrecovery=setenv bootargs $recoverybootargs" \
804 " console=$consoledev,$baudrate $othbootargs; " \
805 "run norloadrecovery; " \
806 "bootm $kerneladdr - $dtbaddr\0" \
807"norbootworking=setenv bootargs $workingbootargs" \
808 " console=$consoledev,$baudrate $othbootargs; " \
809 "run norloadworking; " \
810 "bootm $kerneladdr - $dtbaddr\0" \
811"norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \
812 "setenv cramfsaddr $nor_recoveryaddr; " \
813 "cramfsload $dtbaddr $dtbfile; " \
814 "cramfsload $kerneladdr $kernelfile\0" \
815"norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \
816 "setenv cramfsaddr $nor_workingaddr; " \
817 "cramfsload $dtbaddr $dtbfile; " \
818 "cramfsload $kerneladdr $kernelfile\0" \
819"othbootargs=quiet\0" \
820"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
821 " console=$consoledev,$baudrate $othbootargs; " \
822 "tftp $rootfsaddr $rootfsfile; " \
823 "tftp $loadaddr $kernelfile; " \
824 "tftp $dtbaddr $dtbfile; " \
825 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \
826"ramdisk_size=120000\0" \
827"ramdiskfile=rootfs.ext2.gz.uboot\0" \
828"recoveryaddr=0x02F00000\0" \
829"recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \
830"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
831 "mw.l 0xffe0f008 0x00400000\0" \
832"rootfsaddr=0x02F00000\0" \
833"rootfsfile=rootfs.ext2.gz.uboot\0" \
834"rootpath=/opt/nfsroot\0" \
835"silent=1\0" \
836"tftpflash=tftpboot $loadaddr $uboot; " \
837 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
838 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
839 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
840 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
841 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
842"uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
843"ubootaddr=0x01000000\0" \
844"ubootfile=u-boot.bin\0" \
845"upgrade=run flashworking\0" \
846"workingaddr=0x02F00000\0" \
847"workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
848
849#else /* For Arcturus Modules */
850
851#define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */
852#define CONFIG_EXTRA_ENV_SETTINGS \
853"bootcmd=run norkernel\0" \
854"bootfile=uImage\0" \
855"consoledev=ttyS0\0" \
856"dtbaddr=0x00c00000\0" \
857"dtbfile=image.dtb\0" \
858"ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
859"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
860"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
861"fileaddr=0x01000000\0" \
862"filesize=0x00080000\0" \
863"flashmbr=sf probe 0; " \
864 "tftp $loadaddr $mbr; " \
865 "sf erase $mbr_offset +$filesize; " \
866 "sf write $loadaddr $mbr_offset $filesize\0" \
867"flashuboot=tftp $loadaddr $ubootfile; " \
868 "protect off $nor_ubootaddr0 +$filesize; " \
869 "erase $nor_ubootaddr0 +$filesize; " \
870 "cp.b $loadaddr $nor_ubootaddr0 $filesize; " \
871 "protect on $nor_ubootaddr0 +$filesize; " \
872 "protect off $nor_ubootaddr1 +$filesize; " \
873 "erase $nor_ubootaddr1 +$filesize; " \
874 "cp.b $loadaddr $nor_ubootaddr1 $filesize; " \
875 "protect on $nor_ubootaddr1 +$filesize\0 " \
876"format0=protect off $part0base +$part0size; " \
877 "erase $part0base +$part0size\0" \
878"format1=protect off $part1base +$part1size; " \
879 "erase $part1base +$part1size\0" \
880"format2=protect off $part2base +$part2size; " \
881 "erase $part2base +$part2size\0" \
882"format3=protect off $part3base +$part3size; " \
883 "erase $part3base +$part3size\0" \
884"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
885"kerneladdr=0x01100000\0" \
886"kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \
887"kernelfile=uImage\0" \
888"loadaddr=0x01000000\0" \
889"mbr=uCP1020.mbr\0" \
890"mbr_offset=0x00000000\0" \
891"netdev=eth0\0" \
892"nor_ubootaddr0=0xEC000000\0" \
893"nor_ubootaddr1=0xEFF80000\0" \
894"norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \
895 "run norkernelload; " \
896 "bootm $kerneladdr - $dtbaddr\0" \
897"norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \
898 "setenv cramfsaddr $part0base; " \
899 "cramfsload $dtbaddr $dtbfile; " \
900 "cramfsload $kerneladdr $kernelfile\0" \
901"part0base=0xEC100000\0" \
902"part0size=0x00700000\0" \
903"part1base=0xEC800000\0" \
904"part1size=0x02000000\0" \
905"part2base=0xEE800000\0" \
906"part2size=0x00800000\0" \
907"part3base=0xEF000000\0" \
908"part3size=0x00F80000\0" \
909"partENVbase=0xEC080000\0" \
910"partENVsize=0x00080000\0" \
911"program0=tftp part0-000000.bin; " \
912 "protect off $part0base +$filesize; " \
913 "erase $part0base +$filesize; " \
914 "cp.b $loadaddr $part0base $filesize; " \
915 "echo Verifying...; " \
916 "cmp.b $loadaddr $part0base $filesize\0" \
917"program1=tftp part1-000000.bin; " \
918 "protect off $part1base +$filesize; " \
919 "erase $part1base +$filesize; " \
920 "cp.b $loadaddr $part1base $filesize; " \
921 "echo Verifying...; " \
922 "cmp.b $loadaddr $part1base $filesize\0" \
923"program2=tftp part2-000000.bin; " \
924 "protect off $part2base +$filesize; " \
925 "erase $part2base +$filesize; " \
926 "cp.b $loadaddr $part2base $filesize; " \
927 "echo Verifying...; " \
928 "cmp.b $loadaddr $part2base $filesize\0" \
929"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
930 " console=$consoledev,$baudrate $othbootargs; " \
931 "tftp $rootfsaddr $rootfsfile; " \
932 "tftp $loadaddr $kernelfile; " \
933 "tftp $dtbaddr $dtbfile; " \
934 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \
935"ramdisk_size=120000\0" \
936"ramdiskfile=rootfs.ext2.gz.uboot\0" \
937"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
938 "mw.l 0xffe0f008 0x00400000\0" \
939"rootfsaddr=0x02F00000\0" \
940"rootfsfile=rootfs.ext2.gz.uboot\0" \
941"rootpath=/opt/nfsroot\0" \
942"spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \
943 "sf probe 0; sf erase 0 +$filesize; " \
944 "sf write $loadaddr 0 $filesize\0" \
945"spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
946 "protect off 0xeC000000 +$filesize; " \
947 "erase 0xEC000000 +$filesize; " \
948 "cp.b $loadaddr 0xEC000000 $filesize; " \
949 "cmp.b $loadaddr 0xEC000000 $filesize; " \
950 "protect on 0xeC000000 +$filesize\0" \
951"tftpflash=tftpboot $loadaddr $uboot; " \
952 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
953 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
954 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
955 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
956 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
957"uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
958"ubootfile=u-boot.bin\0" \
959"upgrade=run flashuboot\0" \
960"usb_phy_type=ulpi\0 " \
961"boot_nfs= " \
962 "setenv bootargs root=/dev/nfs rw " \
963 "nfsroot=$serverip:$rootpath " \
964 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
965 "console=$consoledev,$baudrate $othbootargs;" \
966 "tftp $loadaddr $bootfile;" \
967 "tftp $fdtaddr $fdtfile;" \
968 "bootm $loadaddr - $fdtaddr\0" \
969"boot_hd = " \
970 "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
971 "console=$consoledev,$baudrate $othbootargs;" \
972 "usb start;" \
973 "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
974 "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
975 "bootm $loadaddr - $fdtaddr\0" \
976"boot_usb_fat = " \
977 "setenv bootargs root=/dev/ram rw " \
978 "console=$consoledev,$baudrate $othbootargs " \
979 "ramdisk_size=$ramdisk_size;" \
980 "usb start;" \
981 "fatload usb 0:2 $loadaddr $bootfile;" \
982 "fatload usb 0:2 $fdtaddr $fdtfile;" \
983 "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \
984 "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \
985"boot_usb_ext2 = " \
986 "setenv bootargs root=/dev/ram rw " \
987 "console=$consoledev,$baudrate $othbootargs " \
988 "ramdisk_size=$ramdisk_size;" \
989 "usb start;" \
990 "ext2load usb 0:4 $loadaddr $bootfile;" \
991 "ext2load usb 0:4 $fdtaddr $fdtfile;" \
992 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
993 "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \
994"boot_nor = " \
995 "setenv bootargs root=/dev/$jffs2nor rw " \
996 "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \
997 "bootm $norbootaddr - $norfdtaddr\0 " \
998"boot_ram = " \
999 "setenv bootargs root=/dev/ram rw " \
1000 "console=$consoledev,$baudrate $othbootargs " \
1001 "ramdisk_size=$ramdisk_size;" \
1002 "tftp $ramdiskaddr $ramdiskfile;" \
1003 "tftp $loadaddr $bootfile;" \
1004 "tftp $fdtaddr $fdtfile;" \
1005 "bootm $loadaddr $ramdiskaddr $fdtaddr\0"
1006
1007#endif
1008#endif
1009
1010#endif /* __CONFIG_H */