include/configs/ls1046a_common.h

/*
 * Copyright 2016 Freescale Semiconductor
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __LS1046A_COMMON_H
#define __LS1046A_COMMON_H

/* SPL build */
#ifdef CONFIG_SPL_BUILD
#define SPL_NO_QBMAN
#define SPL_NO_FMAN
#define SPL_NO_ENV
#define SPL_NO_MISC
#define SPL_NO_QSPI
#define SPL_NO_USB
#define SPL_NO_SATA
#endif
#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
#define SPL_NO_MMC
#endif
#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT))
#define SPL_NO_IFC
#endif

#define CONFIG_REMAKE_ELF
#define CONFIG_FSL_LAYERSCAPE
#define CONFIG_MP
#define CONFIG_GICV2

#include <asm/arch/config.h>
#include <asm/arch/stream_id_lsch2.h>

/* Link Definitions */
#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)

#define CONFIG_SUPPORT_RAW_INITRD

#define CONFIG_SKIP_LOWLEVEL_INIT

#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL

#define CPU_RELEASE_ADDR               secondary_boot_func

/* Generic Timer Definitions */
#define COUNTER_FREQUENCY		25000000	/* 25MHz */

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 1024 * 1024)

/* Serial Port */
#define CONFIG_CONS_INDEX		1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK          (get_serial_clock())

#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

/* SD boot SPL */
#ifdef CONFIG_SD_BOOT
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
#define CONFIG_SPL_WATCHDOG_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT

#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_TEXT_BASE		0x10000000
#define CONFIG_SPL_MAX_SIZE		0x1f000		/* 124 KiB */
#define CONFIG_SPL_STACK		0x10020000
#define CONFIG_SPL_PAD_TO		0x21000		/* 132 KiB */
#define CONFIG_SPL_BSS_START_ADDR	0x8f000000
#define CONFIG_SPL_BSS_MAX_SIZE		0x80000
#define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
					CONFIG_SPL_BSS_MAX_SIZE)
#define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000

#ifdef CONFIG_SECURE_BOOT
#define CONFIG_U_BOOT_HDR_SIZE				(16 << 10)
/*
 * HDR would be appended at end of image and copied to DDR along
 * with U-Boot image. Here u-boot max. size is 512K. So if binary
 * size increases then increase this size in case of secure boot as
 * it uses raw u-boot image instead of fit image.
 */
#define CONFIG_SYS_MONITOR_LEN		(0x100000 + CONFIG_U_BOOT_HDR_SIZE)
#else
#define CONFIG_SYS_MONITOR_LEN		0x100000
#endif /* ifdef CONFIG_SECURE_BOOT */
#endif

/* NAND SPL */
#ifdef CONFIG_NAND_BOOT
#define CONFIG_SPL_PBL_PAD
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_SPL_WATCHDOG_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT

#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
#define CONFIG_SPL_TEXT_BASE		0x10000000
#define CONFIG_SPL_MAX_SIZE		0x17000		/* 90 KiB */
#define CONFIG_SPL_STACK		0x1001f000
#define CONFIG_SYS_NAND_U_BOOT_DST	CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE

#define CONFIG_SPL_BSS_START_ADDR	0x8f000000
#define CONFIG_SPL_BSS_MAX_SIZE		0x80000
#define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
					CONFIG_SPL_BSS_MAX_SIZE)
#define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
#define CONFIG_SYS_MONITOR_LEN		0xa0000
#endif

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1
#define CONFIG_SYS_I2C_MXC_I2C2
#define CONFIG_SYS_I2C_MXC_I2C3
#define CONFIG_SYS_I2C_MXC_I2C4

/* PCIe */
#define CONFIG_PCIE1		/* PCIE controller 1 */
#define CONFIG_PCIE2		/* PCIE controller 2 */
#define CONFIG_PCIE3		/* PCIE controller 3 */

#ifdef CONFIG_PCI
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_CMD_PCI
#endif

/* Command line configuration */
#ifndef SPL_NO_ENV
#define CONFIG_CMD_ENV
#endif

/* MMC */
#ifndef SPL_NO_MMC
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#endif
#endif

#ifndef SPL_NO_QBMAN
#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
#endif

/* FMan ucode */
#ifndef SPL_NO_FMAN
#define CONFIG_SYS_DPAA_FMAN
#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_FM_MURAM_SIZE	0x60000
#endif

#ifdef CONFIG_SD_BOOT
/*
 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 18432(0x4800).
 */
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
#define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x4800)
#elif defined(CONFIG_QSPI_BOOT)
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
#define CONFIG_SYS_FMAN_FW_ADDR		0x40900000
#define CONFIG_ENV_SPI_BUS		0
#define CONFIG_ENV_SPI_CS		0
#define CONFIG_ENV_SPI_MAX_HZ		1000000
#define CONFIG_ENV_SPI_MODE		0x03
#elif defined(CONFIG_NAND_BOOT)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
#define CONFIG_SYS_FMAN_FW_ADDR		(72 * CONFIG_SYS_NAND_BLOCK_SIZE)
#else
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
#define CONFIG_SYS_FMAN_FW_ADDR		0x60900000
#endif
#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#endif

/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE		128

#ifndef SPL_NO_MISC
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS		\
	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
	"loadaddr=0x80100000\0"			\
	"ramdisk_addr=0x800000\0"		\
	"ramdisk_size=0x2000000\0"		\
	"fdt_high=0xffffffffffffffff\0"		\
	"initrd_high=0xffffffffffffffff\0"	\
	"kernel_start=0x1000000\0"		\
	"kernel_load=0xa0000000\0"		\
	"kernel_size=0x2800000\0"		\
	"console=ttyS0,115200\0"                \
		MTDPARTS_DEFAULT "\0"

#define CONFIG_BOOTARGS			"console=ttyS0,115200 root=/dev/ram0 " \
					"earlycon=uart8250,mmio,0x21c0500 " \
					MTDPARTS_DEFAULT
#endif

/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
					sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE /* Boot args buffer */
#define CONFIG_SYS_LONGHELP

#ifndef SPL_NO_MISC
#define CONFIG_CMDLINE_EDITING		1
#endif

#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS		64	/* max command args */

#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */

/* Hash command with SHA acceleration supported in hardware */
#ifdef CONFIG_FSL_CAAM
#define CONFIG_CMD_HASH
#define CONFIG_SHA_HW_ACCEL
#endif

#endif /* __LS1046A_COMMON_H */