blob: eef433e768ea99f300adaf9fcfaf58b410f90ba3 [file] [log] [blame]
Alex Nemirovsky7d706a82020-01-30 12:34:59 -08001// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Copyright (C) 2020, Cortina Access Inc.
4 */
5
6/dts-v1/;
7
8/ {
9 #address-cells = <2>;
10 #size-cells = <1>;
11
12 mmc0: mmc@f4400000 {
Alex Nemirovsky1ac64472020-05-21 17:24:23 -070013 compatible = "cortina,ca-mmc";
Alex Nemirovsky7d706a82020-01-30 12:34:59 -080014 reg = <0x0 0xf4400000 0x1000>;
15 bus-width = <4>;
Alex Nemirovsky7d706a82020-01-30 12:34:59 -080016 sd_dll_ctrl = <0xf43200e8>;
17 io_drv_ctrl = <0xf432004c>;
18 };
19
20 gpio0: gpio-controller@0xf4329280 {
21 compatible = "cortina,ca-gpio";
22 reg = <0x0 0xf4329280 0x24>;
23 gpio-controller;
24 #gpio-cells = <2>;
25 status = "okay";
26 };
27 gpio1: gpio-controller@0xf43292a4 {
28 compatible = "cortina,ca-gpio";
29 reg = <0x0 0xf43292a4 0x24>;
30 gpio-controller;
31 #gpio-cells = <2>;
32 status = "disabled";
33 };
34
35 watchdog: watchdog@0xf432901c {
36 compatible = "cortina,ca-wdt";
37 reg = <0x0 0xf432901c 0x34>,
38 <0x0 0xf4320020 0x04>;
39 status = "okay";
40 };
41
42 uart0: serial@0xf4329148 {
43 u-boot,dm-pre-reloc;
44 compatible = "cortina,ca-uart";
45 reg = <0x0 0xf4329148 0x30>;
46 status = "okay";
47 };
48
49 i2c: i2c@f4329120 {
50 compatible = "cortina,ca-i2c";
51 reg = <0x0 0xf4329120 0x28>;
52 clock-frequency = <400000>;
53 };
54
55 sflash: sflash-controller@f4324000 {
56 #address-cells = <2>;
57 #size-cells = <1>;
58 compatible = "cortina,ca-sflash";
59 reg = <0x0 0xf4324000 0x50>;
60 reg-names = "sflash-regs";
61 flash@0 {
62 compatible = "jedec,spi-nor";
63 spi-rx-bus-width = <1>;
64 spi-max-frequency = <108000000>;
65 };
66 };
Jway Linedca8ed2020-06-30 21:08:07 -070067
68 leds: led-controller@f43200f0 {
69 compatible = "cortina,ca-leds";
70 reg = <0x0 0xf43200f0 0x40>;
71
72 cortina,blink-rate1 = <256>;
73 cortina,blink-rate2 = <512>;
74
75 led@0 {
76 pin = <0>;
77 active-low;
78 blink-sel =<0>;
79 port = <0>;
80 off-event = <0>;
81 label = "led0";
82 };
83
84 led@1 {
85 pin = <1>;
86 active-low;
87 blink-sel =<1>;
88 label = "led1";
89 };
90
91 led@2 {
92 pin = <2>;
93 active-low;
94 label = "led2";
95 };
96
97 };
Alex Nemirovsky7d706a82020-01-30 12:34:59 -080098};