Wenyou Yang | 110fa97 | 2017-03-24 09:18:41 +0800 | [diff] [blame] | 1 | /* |
| 2 | * sama5d3.dtsi - Device Tree Include file for SAMA5D3 family SoC |
| 3 | * applies to SAMA5D31, SAMA5D33, SAMA5D34, SAMA5D35, SAMA5D36 SoC |
| 4 | * |
| 5 | * Copyright (C) 2013 Atmel, |
| 6 | * 2013 Ludovic Desroches <ludovic.desroches@atmel.com> |
| 7 | * |
| 8 | * Licensed under GPLv2 or later. |
| 9 | */ |
| 10 | |
| 11 | #include "skeleton.dtsi" |
| 12 | #include <dt-bindings/dma/at91.h> |
| 13 | #include <dt-bindings/pinctrl/at91.h> |
| 14 | #include <dt-bindings/interrupt-controller/irq.h> |
| 15 | #include <dt-bindings/gpio/gpio.h> |
| 16 | #include <dt-bindings/clock/at91.h> |
| 17 | |
| 18 | / { |
| 19 | model = "Atmel SAMA5D3 family SoC"; |
| 20 | compatible = "atmel,sama5d3", "atmel,sama5"; |
| 21 | interrupt-parent = <&aic>; |
| 22 | |
| 23 | aliases { |
| 24 | serial0 = &dbgu; |
| 25 | serial1 = &usart0; |
| 26 | serial2 = &usart1; |
| 27 | serial3 = &usart2; |
| 28 | serial4 = &usart3; |
| 29 | serial5 = &uart0; |
| 30 | gpio0 = &pioA; |
| 31 | gpio1 = &pioB; |
| 32 | gpio2 = &pioC; |
| 33 | gpio3 = &pioD; |
| 34 | gpio4 = &pioE; |
| 35 | tcb0 = &tcb0; |
| 36 | i2c0 = &i2c0; |
| 37 | i2c1 = &i2c1; |
| 38 | i2c2 = &i2c2; |
| 39 | ssc0 = &ssc0; |
| 40 | ssc1 = &ssc1; |
| 41 | pwm0 = &pwm0; |
| 42 | }; |
| 43 | cpus { |
| 44 | #address-cells = <1>; |
| 45 | #size-cells = <0>; |
| 46 | cpu@0 { |
| 47 | device_type = "cpu"; |
| 48 | compatible = "arm,cortex-a5"; |
| 49 | reg = <0x0>; |
| 50 | }; |
| 51 | }; |
| 52 | |
| 53 | pmu { |
| 54 | compatible = "arm,cortex-a5-pmu"; |
| 55 | interrupts = <46 IRQ_TYPE_LEVEL_HIGH 0>; |
| 56 | }; |
| 57 | |
| 58 | memory { |
| 59 | reg = <0x20000000 0x8000000>; |
| 60 | }; |
| 61 | |
| 62 | clocks { |
| 63 | slow_xtal: slow_xtal { |
| 64 | compatible = "fixed-clock"; |
| 65 | #clock-cells = <0>; |
| 66 | clock-frequency = <0>; |
| 67 | }; |
| 68 | |
| 69 | main_xtal: main_xtal { |
| 70 | compatible = "fixed-clock"; |
| 71 | #clock-cells = <0>; |
| 72 | clock-frequency = <0>; |
| 73 | }; |
| 74 | |
| 75 | adc_op_clk: adc_op_clk{ |
| 76 | compatible = "fixed-clock"; |
| 77 | #clock-cells = <0>; |
| 78 | clock-frequency = <1000000>; |
| 79 | }; |
| 80 | }; |
| 81 | |
| 82 | sram: sram@00300000 { |
| 83 | compatible = "mmio-sram"; |
| 84 | reg = <0x00300000 0x20000>; |
| 85 | }; |
| 86 | |
| 87 | ahb { |
| 88 | compatible = "simple-bus"; |
| 89 | #address-cells = <1>; |
| 90 | #size-cells = <1>; |
| 91 | ranges; |
| 92 | u-boot,dm-pre-reloc; |
| 93 | |
| 94 | apb { |
| 95 | compatible = "simple-bus"; |
| 96 | #address-cells = <1>; |
| 97 | #size-cells = <1>; |
| 98 | ranges; |
| 99 | u-boot,dm-pre-reloc; |
| 100 | |
| 101 | mmc0: mmc@f0000000 { |
| 102 | compatible = "atmel,hsmci"; |
| 103 | reg = <0xf0000000 0x600>; |
| 104 | interrupts = <21 IRQ_TYPE_LEVEL_HIGH 0>; |
| 105 | dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(0)>; |
| 106 | dma-names = "rxtx"; |
| 107 | pinctrl-names = "default"; |
| 108 | pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7>; |
| 109 | status = "disabled"; |
| 110 | #address-cells = <1>; |
| 111 | #size-cells = <0>; |
| 112 | clocks = <&mci0_clk>; |
| 113 | clock-names = "mci_clk"; |
| 114 | }; |
| 115 | |
| 116 | spi0: spi@f0004000 { |
| 117 | #address-cells = <1>; |
| 118 | #size-cells = <0>; |
| 119 | compatible = "atmel,at91rm9200-spi"; |
| 120 | reg = <0xf0004000 0x100>; |
| 121 | interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>; |
| 122 | dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(1)>, |
| 123 | <&dma0 2 AT91_DMA_CFG_PER_ID(2)>; |
| 124 | dma-names = "tx", "rx"; |
| 125 | pinctrl-names = "default"; |
| 126 | pinctrl-0 = <&pinctrl_spi0>; |
| 127 | clocks = <&spi0_clk>; |
| 128 | clock-names = "spi_clk"; |
| 129 | status = "disabled"; |
| 130 | }; |
| 131 | |
| 132 | ssc0: ssc@f0008000 { |
| 133 | compatible = "atmel,at91sam9g45-ssc"; |
| 134 | reg = <0xf0008000 0x4000>; |
| 135 | interrupts = <38 IRQ_TYPE_LEVEL_HIGH 4>; |
| 136 | dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(13)>, |
| 137 | <&dma0 2 AT91_DMA_CFG_PER_ID(14)>; |
| 138 | dma-names = "tx", "rx"; |
| 139 | pinctrl-names = "default"; |
| 140 | pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; |
| 141 | clocks = <&ssc0_clk>; |
| 142 | clock-names = "pclk"; |
| 143 | status = "disabled"; |
| 144 | }; |
| 145 | |
| 146 | tcb0: timer@f0010000 { |
| 147 | compatible = "atmel,at91sam9x5-tcb"; |
| 148 | reg = <0xf0010000 0x100>; |
| 149 | interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>; |
| 150 | clocks = <&tcb0_clk>, <&clk32k>; |
| 151 | clock-names = "t0_clk", "slow_clk"; |
| 152 | }; |
| 153 | |
| 154 | i2c0: i2c@f0014000 { |
| 155 | compatible = "atmel,at91sam9x5-i2c"; |
| 156 | reg = <0xf0014000 0x4000>; |
| 157 | interrupts = <18 IRQ_TYPE_LEVEL_HIGH 6>; |
| 158 | dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(7)>, |
| 159 | <&dma0 2 AT91_DMA_CFG_PER_ID(8)>; |
| 160 | dma-names = "tx", "rx"; |
| 161 | pinctrl-names = "default"; |
| 162 | pinctrl-0 = <&pinctrl_i2c0>; |
| 163 | #address-cells = <1>; |
| 164 | #size-cells = <0>; |
| 165 | clocks = <&twi0_clk>; |
| 166 | status = "disabled"; |
| 167 | }; |
| 168 | |
| 169 | i2c1: i2c@f0018000 { |
| 170 | compatible = "atmel,at91sam9x5-i2c"; |
| 171 | reg = <0xf0018000 0x4000>; |
| 172 | interrupts = <19 IRQ_TYPE_LEVEL_HIGH 6>; |
| 173 | dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(9)>, |
| 174 | <&dma0 2 AT91_DMA_CFG_PER_ID(10)>; |
| 175 | dma-names = "tx", "rx"; |
| 176 | pinctrl-names = "default"; |
| 177 | pinctrl-0 = <&pinctrl_i2c1>; |
| 178 | #address-cells = <1>; |
| 179 | #size-cells = <0>; |
| 180 | clocks = <&twi1_clk>; |
| 181 | status = "disabled"; |
| 182 | }; |
| 183 | |
| 184 | usart0: serial@f001c000 { |
| 185 | compatible = "atmel,at91sam9260-usart"; |
| 186 | reg = <0xf001c000 0x100>; |
| 187 | interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>; |
| 188 | dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>, |
| 189 | <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>; |
| 190 | dma-names = "tx", "rx"; |
| 191 | pinctrl-names = "default"; |
| 192 | pinctrl-0 = <&pinctrl_usart0>; |
| 193 | clocks = <&usart0_clk>; |
| 194 | clock-names = "usart"; |
| 195 | status = "disabled"; |
| 196 | }; |
| 197 | |
| 198 | usart1: serial@f0020000 { |
| 199 | compatible = "atmel,at91sam9260-usart"; |
| 200 | reg = <0xf0020000 0x100>; |
| 201 | interrupts = <13 IRQ_TYPE_LEVEL_HIGH 5>; |
| 202 | dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(5)>, |
| 203 | <&dma0 2 (AT91_DMA_CFG_PER_ID(6) | AT91_DMA_CFG_FIFOCFG_ASAP)>; |
| 204 | dma-names = "tx", "rx"; |
| 205 | pinctrl-names = "default"; |
| 206 | pinctrl-0 = <&pinctrl_usart1>; |
| 207 | clocks = <&usart1_clk>; |
| 208 | clock-names = "usart"; |
| 209 | status = "disabled"; |
| 210 | }; |
| 211 | |
| 212 | uart0: serial@f0024000 { |
| 213 | compatible = "atmel,at91sam9260-usart"; |
| 214 | reg = <0xf0024000 0x100>; |
| 215 | interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>; |
| 216 | pinctrl-names = "default"; |
| 217 | pinctrl-0 = <&pinctrl_uart0>; |
| 218 | clocks = <&uart0_clk>; |
| 219 | clock-names = "usart"; |
| 220 | status = "disabled"; |
| 221 | }; |
| 222 | |
| 223 | pwm0: pwm@f002c000 { |
| 224 | compatible = "atmel,sama5d3-pwm"; |
| 225 | reg = <0xf002c000 0x300>; |
| 226 | interrupts = <28 IRQ_TYPE_LEVEL_HIGH 4>; |
| 227 | #pwm-cells = <3>; |
| 228 | clocks = <&pwm_clk>; |
| 229 | status = "disabled"; |
| 230 | }; |
| 231 | |
| 232 | isi: isi@f0034000 { |
| 233 | compatible = "atmel,at91sam9g45-isi"; |
| 234 | reg = <0xf0034000 0x4000>; |
| 235 | interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>; |
| 236 | pinctrl-names = "default"; |
| 237 | pinctrl-0 = <&pinctrl_isi_data_0_7>; |
| 238 | clocks = <&isi_clk>; |
| 239 | clock-names = "isi_clk"; |
| 240 | status = "disabled"; |
Wenyou Yang | 110fa97 | 2017-03-24 09:18:41 +0800 | [diff] [blame] | 241 | }; |
| 242 | |
| 243 | sfr: sfr@f0038000 { |
| 244 | compatible = "atmel,sama5d3-sfr", "syscon"; |
| 245 | reg = <0xf0038000 0x60>; |
| 246 | }; |
| 247 | |
| 248 | mmc1: mmc@f8000000 { |
| 249 | compatible = "atmel,hsmci"; |
| 250 | reg = <0xf8000000 0x600>; |
| 251 | interrupts = <22 IRQ_TYPE_LEVEL_HIGH 0>; |
| 252 | dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(0)>; |
| 253 | dma-names = "rxtx"; |
| 254 | pinctrl-names = "default"; |
| 255 | pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>; |
| 256 | status = "disabled"; |
| 257 | #address-cells = <1>; |
| 258 | #size-cells = <0>; |
| 259 | clocks = <&mci1_clk>; |
| 260 | clock-names = "mci_clk"; |
| 261 | }; |
| 262 | |
| 263 | spi1: spi@f8008000 { |
| 264 | #address-cells = <1>; |
| 265 | #size-cells = <0>; |
| 266 | compatible = "atmel,at91rm9200-spi"; |
| 267 | reg = <0xf8008000 0x100>; |
| 268 | interrupts = <25 IRQ_TYPE_LEVEL_HIGH 3>; |
| 269 | dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(15)>, |
| 270 | <&dma1 2 AT91_DMA_CFG_PER_ID(16)>; |
| 271 | dma-names = "tx", "rx"; |
| 272 | pinctrl-names = "default"; |
| 273 | pinctrl-0 = <&pinctrl_spi1>; |
| 274 | clocks = <&spi1_clk>; |
| 275 | clock-names = "spi_clk"; |
| 276 | status = "disabled"; |
| 277 | }; |
| 278 | |
| 279 | ssc1: ssc@f800c000 { |
| 280 | compatible = "atmel,at91sam9g45-ssc"; |
| 281 | reg = <0xf800c000 0x4000>; |
| 282 | interrupts = <39 IRQ_TYPE_LEVEL_HIGH 4>; |
| 283 | dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(3)>, |
| 284 | <&dma1 2 AT91_DMA_CFG_PER_ID(4)>; |
| 285 | dma-names = "tx", "rx"; |
| 286 | pinctrl-names = "default"; |
| 287 | pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; |
| 288 | clocks = <&ssc1_clk>; |
| 289 | clock-names = "pclk"; |
| 290 | status = "disabled"; |
| 291 | }; |
| 292 | |
| 293 | adc0: adc@f8018000 { |
| 294 | #address-cells = <1>; |
| 295 | #size-cells = <0>; |
| 296 | compatible = "atmel,at91sam9x5-adc"; |
| 297 | reg = <0xf8018000 0x100>; |
| 298 | interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>; |
| 299 | pinctrl-names = "default"; |
| 300 | pinctrl-0 = < |
| 301 | &pinctrl_adc0_adtrg |
| 302 | &pinctrl_adc0_ad0 |
| 303 | &pinctrl_adc0_ad1 |
| 304 | &pinctrl_adc0_ad2 |
| 305 | &pinctrl_adc0_ad3 |
| 306 | &pinctrl_adc0_ad4 |
| 307 | &pinctrl_adc0_ad5 |
| 308 | &pinctrl_adc0_ad6 |
| 309 | &pinctrl_adc0_ad7 |
| 310 | &pinctrl_adc0_ad8 |
| 311 | &pinctrl_adc0_ad9 |
| 312 | &pinctrl_adc0_ad10 |
| 313 | &pinctrl_adc0_ad11 |
| 314 | >; |
| 315 | clocks = <&adc_clk>, |
| 316 | <&adc_op_clk>; |
| 317 | clock-names = "adc_clk", "adc_op_clk"; |
| 318 | atmel,adc-channels-used = <0xfff>; |
| 319 | atmel,adc-startup-time = <40>; |
| 320 | atmel,adc-use-external-triggers; |
| 321 | atmel,adc-vref = <3000>; |
| 322 | atmel,adc-res = <10 12>; |
| 323 | atmel,adc-sample-hold-time = <11>; |
| 324 | atmel,adc-res-names = "lowres", "highres"; |
| 325 | status = "disabled"; |
| 326 | |
| 327 | trigger@0 { |
| 328 | reg = <0>; |
| 329 | trigger-name = "external-rising"; |
| 330 | trigger-value = <0x1>; |
| 331 | trigger-external; |
| 332 | }; |
| 333 | trigger@1 { |
| 334 | reg = <1>; |
| 335 | trigger-name = "external-falling"; |
| 336 | trigger-value = <0x2>; |
| 337 | trigger-external; |
| 338 | }; |
| 339 | trigger@2 { |
| 340 | reg = <2>; |
| 341 | trigger-name = "external-any"; |
| 342 | trigger-value = <0x3>; |
| 343 | trigger-external; |
| 344 | }; |
| 345 | trigger@3 { |
| 346 | reg = <3>; |
| 347 | trigger-name = "continuous"; |
| 348 | trigger-value = <0x6>; |
| 349 | }; |
| 350 | }; |
| 351 | |
| 352 | i2c2: i2c@f801c000 { |
| 353 | compatible = "atmel,at91sam9x5-i2c"; |
| 354 | reg = <0xf801c000 0x4000>; |
| 355 | interrupts = <20 IRQ_TYPE_LEVEL_HIGH 6>; |
| 356 | dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(11)>, |
| 357 | <&dma1 2 AT91_DMA_CFG_PER_ID(12)>; |
| 358 | dma-names = "tx", "rx"; |
| 359 | pinctrl-names = "default"; |
| 360 | pinctrl-0 = <&pinctrl_i2c2>; |
| 361 | #address-cells = <1>; |
| 362 | #size-cells = <0>; |
| 363 | clocks = <&twi2_clk>; |
| 364 | status = "disabled"; |
| 365 | }; |
| 366 | |
| 367 | usart2: serial@f8020000 { |
| 368 | compatible = "atmel,at91sam9260-usart"; |
| 369 | reg = <0xf8020000 0x100>; |
| 370 | interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; |
| 371 | dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(7)>, |
| 372 | <&dma1 2 (AT91_DMA_CFG_PER_ID(8) | AT91_DMA_CFG_FIFOCFG_ASAP)>; |
| 373 | dma-names = "tx", "rx"; |
| 374 | pinctrl-names = "default"; |
| 375 | pinctrl-0 = <&pinctrl_usart2>; |
| 376 | clocks = <&usart2_clk>; |
| 377 | clock-names = "usart"; |
| 378 | status = "disabled"; |
| 379 | }; |
| 380 | |
| 381 | usart3: serial@f8024000 { |
| 382 | compatible = "atmel,at91sam9260-usart"; |
| 383 | reg = <0xf8024000 0x100>; |
| 384 | interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; |
| 385 | dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(9)>, |
| 386 | <&dma1 2 (AT91_DMA_CFG_PER_ID(10) | AT91_DMA_CFG_FIFOCFG_ASAP)>; |
| 387 | dma-names = "tx", "rx"; |
| 388 | pinctrl-names = "default"; |
| 389 | pinctrl-0 = <&pinctrl_usart3>; |
| 390 | clocks = <&usart3_clk>; |
| 391 | clock-names = "usart"; |
| 392 | status = "disabled"; |
| 393 | }; |
| 394 | |
| 395 | sha@f8034000 { |
| 396 | compatible = "atmel,at91sam9g46-sha"; |
| 397 | reg = <0xf8034000 0x100>; |
| 398 | interrupts = <42 IRQ_TYPE_LEVEL_HIGH 0>; |
| 399 | dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(17)>; |
| 400 | dma-names = "tx"; |
| 401 | clocks = <&sha_clk>; |
| 402 | clock-names = "sha_clk"; |
| 403 | }; |
| 404 | |
| 405 | aes@f8038000 { |
| 406 | compatible = "atmel,at91sam9g46-aes"; |
| 407 | reg = <0xf8038000 0x100>; |
| 408 | interrupts = <43 IRQ_TYPE_LEVEL_HIGH 0>; |
| 409 | dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(18)>, |
| 410 | <&dma1 2 AT91_DMA_CFG_PER_ID(19)>; |
| 411 | dma-names = "tx", "rx"; |
| 412 | clocks = <&aes_clk>; |
| 413 | clock-names = "aes_clk"; |
| 414 | }; |
| 415 | |
| 416 | tdes@f803c000 { |
| 417 | compatible = "atmel,at91sam9g46-tdes"; |
| 418 | reg = <0xf803c000 0x100>; |
| 419 | interrupts = <44 IRQ_TYPE_LEVEL_HIGH 0>; |
| 420 | dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(20)>, |
| 421 | <&dma1 2 AT91_DMA_CFG_PER_ID(21)>; |
| 422 | dma-names = "tx", "rx"; |
| 423 | clocks = <&tdes_clk>; |
| 424 | clock-names = "tdes_clk"; |
| 425 | }; |
| 426 | |
| 427 | trng@f8040000 { |
| 428 | compatible = "atmel,at91sam9g45-trng"; |
| 429 | reg = <0xf8040000 0x100>; |
| 430 | interrupts = <45 IRQ_TYPE_LEVEL_HIGH 0>; |
| 431 | clocks = <&trng_clk>; |
| 432 | }; |
| 433 | |
| 434 | dma0: dma-controller@ffffe600 { |
| 435 | compatible = "atmel,at91sam9g45-dma"; |
| 436 | reg = <0xffffe600 0x200>; |
| 437 | interrupts = <30 IRQ_TYPE_LEVEL_HIGH 0>; |
| 438 | #dma-cells = <2>; |
| 439 | clocks = <&dma0_clk>; |
| 440 | clock-names = "dma_clk"; |
| 441 | }; |
| 442 | |
| 443 | dma1: dma-controller@ffffe800 { |
| 444 | compatible = "atmel,at91sam9g45-dma"; |
| 445 | reg = <0xffffe800 0x200>; |
| 446 | interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>; |
| 447 | #dma-cells = <2>; |
| 448 | clocks = <&dma1_clk>; |
| 449 | clock-names = "dma_clk"; |
| 450 | }; |
| 451 | |
| 452 | ramc0: ramc@ffffea00 { |
| 453 | compatible = "atmel,sama5d3-ddramc"; |
| 454 | reg = <0xffffea00 0x200>; |
| 455 | clocks = <&ddrck>, <&mpddr_clk>; |
| 456 | clock-names = "ddrck", "mpddr"; |
| 457 | }; |
| 458 | |
| 459 | dbgu: serial@ffffee00 { |
| 460 | compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"; |
| 461 | reg = <0xffffee00 0x200>; |
| 462 | interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>; |
| 463 | dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(13)>, |
| 464 | <&dma1 2 (AT91_DMA_CFG_PER_ID(14) | AT91_DMA_CFG_FIFOCFG_ASAP)>; |
| 465 | dma-names = "tx", "rx"; |
| 466 | pinctrl-names = "default"; |
| 467 | pinctrl-0 = <&pinctrl_dbgu>; |
| 468 | clocks = <&dbgu_clk>; |
| 469 | clock-names = "usart"; |
| 470 | status = "disabled"; |
| 471 | }; |
| 472 | |
| 473 | aic: interrupt-controller@fffff000 { |
| 474 | #interrupt-cells = <3>; |
| 475 | compatible = "atmel,sama5d3-aic"; |
| 476 | interrupt-controller; |
| 477 | reg = <0xfffff000 0x200>; |
| 478 | atmel,external-irqs = <47>; |
| 479 | }; |
| 480 | |
| 481 | pinctrl@fffff200 { |
| 482 | u-boot,dm-pre-reloc; |
| 483 | #address-cells = <1>; |
| 484 | #size-cells = <1>; |
| 485 | compatible = "atmel,sama5d3-pinctrl", "atmel,at91sam9x5-pinctrl", "simple-bus"; |
| 486 | ranges = <0xfffff200 0xfffff200 0xa00>; |
| 487 | atmel,mux-mask = < |
| 488 | /* A B C */ |
| 489 | 0xffffffff 0xc0fc0000 0xc0ff0000 /* pioA */ |
| 490 | 0xffffffff 0x0ff8ffff 0x00000000 /* pioB */ |
| 491 | 0xffffffff 0xbc00f1ff 0x7c00fc00 /* pioC */ |
| 492 | 0xffffffff 0xc001c0e0 0x0001c1e0 /* pioD */ |
| 493 | 0xffffffff 0xbf9f8000 0x18000000 /* pioE */ |
| 494 | >; |
| 495 | reg = <0xfffff200 0x100 /* pioA */ |
| 496 | 0xfffff400 0x100 /* pioB */ |
| 497 | 0xfffff600 0x100 /* pioC */ |
| 498 | 0xfffff800 0x100 /* pioD */ |
| 499 | 0xfffffa00 0x100 /* pioE */ |
| 500 | >; |
| 501 | |
| 502 | /* shared pinctrl settings */ |
| 503 | adc0 { |
| 504 | pinctrl_adc0_adtrg: adc0_adtrg { |
| 505 | atmel,pins = |
| 506 | <AT91_PIOD 19 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD19 periph A ADTRG */ |
| 507 | }; |
| 508 | pinctrl_adc0_ad0: adc0_ad0 { |
| 509 | atmel,pins = |
| 510 | <AT91_PIOD 20 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD20 periph A AD0 */ |
| 511 | }; |
| 512 | pinctrl_adc0_ad1: adc0_ad1 { |
| 513 | atmel,pins = |
| 514 | <AT91_PIOD 21 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD21 periph A AD1 */ |
| 515 | }; |
| 516 | pinctrl_adc0_ad2: adc0_ad2 { |
| 517 | atmel,pins = |
| 518 | <AT91_PIOD 22 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD22 periph A AD2 */ |
| 519 | }; |
| 520 | pinctrl_adc0_ad3: adc0_ad3 { |
| 521 | atmel,pins = |
| 522 | <AT91_PIOD 23 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD23 periph A AD3 */ |
| 523 | }; |
| 524 | pinctrl_adc0_ad4: adc0_ad4 { |
| 525 | atmel,pins = |
| 526 | <AT91_PIOD 24 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD24 periph A AD4 */ |
| 527 | }; |
| 528 | pinctrl_adc0_ad5: adc0_ad5 { |
| 529 | atmel,pins = |
| 530 | <AT91_PIOD 25 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD25 periph A AD5 */ |
| 531 | }; |
| 532 | pinctrl_adc0_ad6: adc0_ad6 { |
| 533 | atmel,pins = |
| 534 | <AT91_PIOD 26 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD26 periph A AD6 */ |
| 535 | }; |
| 536 | pinctrl_adc0_ad7: adc0_ad7 { |
| 537 | atmel,pins = |
| 538 | <AT91_PIOD 27 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD27 periph A AD7 */ |
| 539 | }; |
| 540 | pinctrl_adc0_ad8: adc0_ad8 { |
| 541 | atmel,pins = |
| 542 | <AT91_PIOD 28 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD28 periph A AD8 */ |
| 543 | }; |
| 544 | pinctrl_adc0_ad9: adc0_ad9 { |
| 545 | atmel,pins = |
| 546 | <AT91_PIOD 29 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD29 periph A AD9 */ |
| 547 | }; |
| 548 | pinctrl_adc0_ad10: adc0_ad10 { |
| 549 | atmel,pins = |
| 550 | <AT91_PIOD 30 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD30 periph A AD10, conflicts with PCK0 */ |
| 551 | }; |
| 552 | pinctrl_adc0_ad11: adc0_ad11 { |
| 553 | atmel,pins = |
| 554 | <AT91_PIOD 31 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD31 periph A AD11, conflicts with PCK1 */ |
| 555 | }; |
| 556 | }; |
| 557 | |
| 558 | dbgu { |
| 559 | u-boot,dm-pre-reloc; |
| 560 | pinctrl_dbgu: dbgu-0 { |
| 561 | u-boot,dm-pre-reloc; |
| 562 | atmel,pins = |
| 563 | <AT91_PIOB 30 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB30 periph A */ |
| 564 | AT91_PIOB 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PB31 periph A with pullup */ |
| 565 | }; |
| 566 | }; |
| 567 | |
| 568 | i2c0 { |
| 569 | pinctrl_i2c0: i2c0-0 { |
| 570 | atmel,pins = |
| 571 | <AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA30 periph A TWD0 pin, conflicts with URXD1, ISI_VSYNC */ |
| 572 | AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA31 periph A TWCK0 pin, conflicts with UTXD1, ISI_HSYNC */ |
| 573 | }; |
| 574 | }; |
| 575 | |
| 576 | i2c1 { |
| 577 | pinctrl_i2c1: i2c1-0 { |
| 578 | atmel,pins = |
| 579 | <AT91_PIOC 26 AT91_PERIPH_B AT91_PINCTRL_NONE /* PC26 periph B TWD1 pin, conflicts with SPI1_NPCS1, ISI_D11 */ |
| 580 | AT91_PIOC 27 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC27 periph B TWCK1 pin, conflicts with SPI1_NPCS2, ISI_D10 */ |
| 581 | }; |
| 582 | }; |
| 583 | |
| 584 | i2c2 { |
| 585 | pinctrl_i2c2: i2c2-0 { |
| 586 | atmel,pins = |
| 587 | <AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_NONE /* TWD2 pin, conflicts with LCDDAT18, ISI_D2 */ |
| 588 | AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* TWCK2 pin, conflicts with LCDDAT19, ISI_D3 */ |
| 589 | }; |
| 590 | }; |
| 591 | |
| 592 | isi { |
| 593 | pinctrl_isi_data_0_7: isi-0-data-0-7 { |
| 594 | atmel,pins = |
| 595 | <AT91_PIOA 16 AT91_PERIPH_C AT91_PINCTRL_NONE /* PA16 periph C ISI_D0, conflicts with LCDDAT16 */ |
| 596 | AT91_PIOA 17 AT91_PERIPH_C AT91_PINCTRL_NONE /* PA17 periph C ISI_D1, conflicts with LCDDAT17 */ |
| 597 | AT91_PIOA 18 AT91_PERIPH_C AT91_PINCTRL_NONE /* PA18 periph C ISI_D2, conflicts with LCDDAT18, TWD2 */ |
| 598 | AT91_PIOA 19 AT91_PERIPH_C AT91_PINCTRL_NONE /* PA19 periph C ISI_D3, conflicts with LCDDAT19, TWCK2 */ |
| 599 | AT91_PIOA 20 AT91_PERIPH_C AT91_PINCTRL_NONE /* PA20 periph C ISI_D4, conflicts with LCDDAT20, PWMH0 */ |
| 600 | AT91_PIOA 21 AT91_PERIPH_C AT91_PINCTRL_NONE /* PA21 periph C ISI_D5, conflicts with LCDDAT21, PWML0 */ |
| 601 | AT91_PIOA 22 AT91_PERIPH_C AT91_PINCTRL_NONE /* PA22 periph C ISI_D6, conflicts with LCDDAT22, PWMH1 */ |
| 602 | AT91_PIOA 23 AT91_PERIPH_C AT91_PINCTRL_NONE /* PA23 periph C ISI_D7, conflicts with LCDDAT23, PWML1 */ |
| 603 | AT91_PIOC 30 AT91_PERIPH_C AT91_PINCTRL_NONE /* PC30 periph C ISI_PCK, conflicts with UTXD0 */ |
| 604 | AT91_PIOA 31 AT91_PERIPH_C AT91_PINCTRL_NONE /* PA31 periph C ISI_HSYNC, conflicts with TWCK0, UTXD1 */ |
| 605 | AT91_PIOA 30 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* PA30 periph C ISI_VSYNC, conflicts with TWD0, URXD1 */ |
| 606 | }; |
| 607 | |
| 608 | pinctrl_isi_data_8_9: isi-0-data-8-9 { |
| 609 | atmel,pins = |
| 610 | <AT91_PIOC 29 AT91_PERIPH_C AT91_PINCTRL_NONE /* PC29 periph C ISI_PD8, conflicts with URXD0, PWMFI2 */ |
| 611 | AT91_PIOC 28 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* PC28 periph C ISI_PD9, conflicts with SPI1_NPCS3, PWMFI0 */ |
| 612 | }; |
| 613 | |
| 614 | pinctrl_isi_data_10_11: isi-0-data-10-11 { |
| 615 | atmel,pins = |
| 616 | <AT91_PIOC 27 AT91_PERIPH_C AT91_PINCTRL_NONE /* PC27 periph C ISI_PD10, conflicts with SPI1_NPCS2, TWCK1 */ |
| 617 | AT91_PIOC 26 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* PC26 periph C ISI_PD11, conflicts with SPI1_NPCS1, TWD1 */ |
| 618 | }; |
| 619 | }; |
| 620 | |
| 621 | mmc0 { |
| 622 | u-boot,dm-pre-reloc; |
| 623 | pinctrl_mmc0_clk_cmd_dat0: mmc0_clk_cmd_dat0 { |
| 624 | u-boot,dm-pre-reloc; |
| 625 | atmel,pins = |
| 626 | <AT91_PIOD 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD9 periph A MCI0_CK */ |
| 627 | AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD0 periph A MCI0_CDA with pullup */ |
| 628 | AT91_PIOD 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PD1 periph A MCI0_DA0 with pullup */ |
| 629 | }; |
| 630 | pinctrl_mmc0_dat1_3: mmc0_dat1_3 { |
| 631 | u-boot,dm-pre-reloc; |
| 632 | atmel,pins = |
| 633 | <AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD2 periph A MCI0_DA1 with pullup */ |
| 634 | AT91_PIOD 3 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD3 periph A MCI0_DA2 with pullup */ |
| 635 | AT91_PIOD 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PD4 periph A MCI0_DA3 with pullup */ |
| 636 | }; |
| 637 | pinctrl_mmc0_dat4_7: mmc0_dat4_7 { |
| 638 | u-boot,dm-pre-reloc; |
| 639 | atmel,pins = |
| 640 | <AT91_PIOD 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD5 periph A MCI0_DA4 with pullup, conflicts with TIOA0, PWMH2 */ |
| 641 | AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD6 periph A MCI0_DA5 with pullup, conflicts with TIOB0, PWML2 */ |
| 642 | AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD7 periph A MCI0_DA6 with pullup, conlicts with TCLK0, PWMH3 */ |
| 643 | AT91_PIOD 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PD8 periph A MCI0_DA7 with pullup, conflicts with PWML3 */ |
| 644 | }; |
| 645 | }; |
| 646 | |
| 647 | mmc1 { |
| 648 | u-boot,dm-pre-reloc; |
| 649 | pinctrl_mmc1_clk_cmd_dat0: mmc1_clk_cmd_dat0 { |
| 650 | u-boot,dm-pre-reloc; |
| 651 | atmel,pins = |
| 652 | <AT91_PIOB 24 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB24 periph A MCI1_CK, conflicts with GRX5 */ |
| 653 | AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PB19 periph A MCI1_CDA with pullup, conflicts with GTX4 */ |
| 654 | AT91_PIOB 20 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PB20 periph A MCI1_DA0 with pullup, conflicts with GTX5 */ |
| 655 | }; |
| 656 | pinctrl_mmc1_dat1_3: mmc1_dat1_3 { |
| 657 | u-boot,dm-pre-reloc; |
| 658 | atmel,pins = |
| 659 | <AT91_PIOB 21 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PB21 periph A MCI1_DA1 with pullup, conflicts with GTX6 */ |
| 660 | AT91_PIOB 22 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PB22 periph A MCI1_DA2 with pullup, conflicts with GTX7 */ |
| 661 | AT91_PIOB 23 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PB23 periph A MCI1_DA3 with pullup, conflicts with GRX4 */ |
| 662 | }; |
| 663 | }; |
| 664 | |
| 665 | nand0 { |
| 666 | pinctrl_nand0_ale_cle: nand0_ale_cle-0 { |
| 667 | atmel,pins = |
| 668 | <AT91_PIOE 21 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PE21 periph A with pullup */ |
| 669 | AT91_PIOE 22 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PE22 periph A with pullup */ |
| 670 | }; |
| 671 | }; |
| 672 | |
| 673 | pwm0 { |
| 674 | pinctrl_pwm0_pwmh0_0: pwm0_pwmh0-0 { |
| 675 | atmel,pins = |
| 676 | <AT91_PIOA 20 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with ISI_D4 and LCDDAT20 */ |
| 677 | }; |
| 678 | pinctrl_pwm0_pwmh0_1: pwm0_pwmh0-1 { |
| 679 | atmel,pins = |
| 680 | <AT91_PIOB 0 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with GTX0 */ |
| 681 | }; |
| 682 | pinctrl_pwm0_pwml0_0: pwm0_pwml0-0 { |
| 683 | atmel,pins = |
| 684 | <AT91_PIOA 21 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with ISI_D5 and LCDDAT21 */ |
| 685 | }; |
| 686 | pinctrl_pwm0_pwml0_1: pwm0_pwml0-1 { |
| 687 | atmel,pins = |
| 688 | <AT91_PIOB 1 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with GTX1 */ |
| 689 | }; |
| 690 | |
| 691 | pinctrl_pwm0_pwmh1_0: pwm0_pwmh1-0 { |
| 692 | atmel,pins = |
| 693 | <AT91_PIOA 22 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with ISI_D6 and LCDDAT22 */ |
| 694 | }; |
| 695 | pinctrl_pwm0_pwmh1_1: pwm0_pwmh1-1 { |
| 696 | atmel,pins = |
| 697 | <AT91_PIOB 4 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with GRX0 */ |
| 698 | }; |
| 699 | pinctrl_pwm0_pwmh1_2: pwm0_pwmh1-2 { |
| 700 | atmel,pins = |
| 701 | <AT91_PIOB 27 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* conflicts with G125CKO and RTS1 */ |
| 702 | }; |
| 703 | pinctrl_pwm0_pwml1_0: pwm0_pwml1-0 { |
| 704 | atmel,pins = |
| 705 | <AT91_PIOA 23 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with ISI_D7 and LCDDAT23 */ |
| 706 | }; |
| 707 | pinctrl_pwm0_pwml1_1: pwm0_pwml1-1 { |
| 708 | atmel,pins = |
| 709 | <AT91_PIOB 5 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with GRX1 */ |
| 710 | }; |
| 711 | pinctrl_pwm0_pwml1_2: pwm0_pwml1-2 { |
| 712 | atmel,pins = |
| 713 | <AT91_PIOE 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with IRQ */ |
| 714 | }; |
| 715 | |
| 716 | pinctrl_pwm0_pwmh2_0: pwm0_pwmh2-0 { |
| 717 | atmel,pins = |
| 718 | <AT91_PIOB 8 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with GTXCK */ |
| 719 | }; |
| 720 | pinctrl_pwm0_pwmh2_1: pwm0_pwmh2-1 { |
| 721 | atmel,pins = |
| 722 | <AT91_PIOD 5 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* conflicts with MCI0_DA4 and TIOA0 */ |
| 723 | }; |
| 724 | pinctrl_pwm0_pwml2_0: pwm0_pwml2-0 { |
| 725 | atmel,pins = |
| 726 | <AT91_PIOB 9 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with GTXEN */ |
| 727 | }; |
| 728 | pinctrl_pwm0_pwml2_1: pwm0_pwml2-1 { |
| 729 | atmel,pins = |
| 730 | <AT91_PIOD 6 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* conflicts with MCI0_DA5 and TIOB0 */ |
| 731 | }; |
| 732 | |
| 733 | pinctrl_pwm0_pwmh3_0: pwm0_pwmh3-0 { |
| 734 | atmel,pins = |
| 735 | <AT91_PIOB 12 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with GRXDV */ |
| 736 | }; |
| 737 | pinctrl_pwm0_pwmh3_1: pwm0_pwmh3-1 { |
| 738 | atmel,pins = |
| 739 | <AT91_PIOD 7 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* conflicts with MCI0_DA6 and TCLK0 */ |
| 740 | }; |
| 741 | pinctrl_pwm0_pwml3_0: pwm0_pwml3-0 { |
| 742 | atmel,pins = |
| 743 | <AT91_PIOB 13 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with GRXER */ |
| 744 | }; |
| 745 | pinctrl_pwm0_pwml3_1: pwm0_pwml3-1 { |
| 746 | atmel,pins = |
| 747 | <AT91_PIOD 8 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* conflicts with MCI0_DA7 */ |
| 748 | }; |
| 749 | }; |
| 750 | |
| 751 | spi0 { |
| 752 | u-boot,dm-pre-reloc; |
| 753 | pinctrl_spi0: spi0-0 { |
| 754 | u-boot,dm-pre-reloc; |
| 755 | atmel,pins = |
| 756 | <AT91_PIOD 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD10 periph A SPI0_MISO pin */ |
| 757 | AT91_PIOD 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD11 periph A SPI0_MOSI pin */ |
| 758 | AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD12 periph A SPI0_SPCK pin */ |
| 759 | }; |
| 760 | }; |
| 761 | |
| 762 | spi1 { |
| 763 | u-boot,dm-pre-reloc; |
| 764 | pinctrl_spi1: spi1-0 { |
| 765 | u-boot,dm-pre-reloc; |
| 766 | atmel,pins = |
| 767 | <AT91_PIOC 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC22 periph A SPI1_MISO pin */ |
| 768 | AT91_PIOC 23 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC23 periph A SPI1_MOSI pin */ |
| 769 | AT91_PIOC 24 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PC24 periph A SPI1_SPCK pin */ |
| 770 | }; |
| 771 | }; |
| 772 | |
| 773 | ssc0 { |
| 774 | pinctrl_ssc0_tx: ssc0_tx { |
| 775 | atmel,pins = |
| 776 | <AT91_PIOC 16 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC16 periph A TK0 */ |
| 777 | AT91_PIOC 17 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC17 periph A TF0 */ |
| 778 | AT91_PIOC 18 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PC18 periph A TD0 */ |
| 779 | }; |
| 780 | |
| 781 | pinctrl_ssc0_rx: ssc0_rx { |
| 782 | atmel,pins = |
| 783 | <AT91_PIOC 19 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC19 periph A RK0 */ |
| 784 | AT91_PIOC 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC20 periph A RF0 */ |
| 785 | AT91_PIOC 21 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PC21 periph A RD0 */ |
| 786 | }; |
| 787 | }; |
| 788 | |
| 789 | ssc1 { |
| 790 | pinctrl_ssc1_tx: ssc1_tx { |
| 791 | atmel,pins = |
| 792 | <AT91_PIOB 2 AT91_PERIPH_B AT91_PINCTRL_NONE /* PB2 periph B TK1, conflicts with GTX2 */ |
| 793 | AT91_PIOB 3 AT91_PERIPH_B AT91_PINCTRL_NONE /* PB3 periph B TF1, conflicts with GTX3 */ |
| 794 | AT91_PIOB 6 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PB6 periph B TD1, conflicts with TD1 */ |
| 795 | }; |
| 796 | |
| 797 | pinctrl_ssc1_rx: ssc1_rx { |
| 798 | atmel,pins = |
| 799 | <AT91_PIOB 7 AT91_PERIPH_B AT91_PINCTRL_NONE /* PB7 periph B RK1, conflicts with EREFCK */ |
| 800 | AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE /* PB10 periph B RF1, conflicts with GTXER */ |
| 801 | AT91_PIOB 11 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PB11 periph B RD1, conflicts with GRXCK */ |
| 802 | }; |
| 803 | }; |
| 804 | |
| 805 | uart0 { |
| 806 | pinctrl_uart0: uart0-0 { |
| 807 | atmel,pins = |
| 808 | <AT91_PIOC 29 AT91_PERIPH_A AT91_PINCTRL_NONE /* conflicts with PWMFI2, ISI_D8 */ |
| 809 | AT91_PIOC 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* conflicts with ISI_PCK */ |
| 810 | }; |
| 811 | }; |
| 812 | |
| 813 | uart1 { |
| 814 | pinctrl_uart1: uart1-0 { |
| 815 | atmel,pins = |
| 816 | <AT91_PIOA 30 AT91_PERIPH_B AT91_PINCTRL_NONE /* conflicts with TWD0, ISI_VSYNC */ |
| 817 | AT91_PIOA 31 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* conflicts with TWCK0, ISI_HSYNC */ |
| 818 | }; |
| 819 | }; |
| 820 | |
| 821 | usart0 { |
| 822 | pinctrl_usart0: usart0-0 { |
| 823 | atmel,pins = |
| 824 | <AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD17 periph A */ |
| 825 | AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PD18 periph A with pullup */ |
| 826 | }; |
| 827 | |
| 828 | pinctrl_usart0_rts_cts: usart0_rts_cts-0 { |
| 829 | atmel,pins = |
| 830 | <AT91_PIOD 15 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD15 periph A, conflicts with SPI0_NPCS2, CANTX0 */ |
| 831 | AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD16 periph A, conflicts with SPI0_NPCS3, PWMFI3 */ |
| 832 | }; |
| 833 | }; |
| 834 | |
| 835 | usart1 { |
| 836 | pinctrl_usart1: usart1-0 { |
| 837 | atmel,pins = |
| 838 | <AT91_PIOB 28 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB28 periph A */ |
| 839 | AT91_PIOB 29 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PB29 periph A with pullup */ |
| 840 | }; |
| 841 | |
| 842 | pinctrl_usart1_rts_cts: usart1_rts_cts-0 { |
| 843 | atmel,pins = |
| 844 | <AT91_PIOB 26 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB26 periph A, conflicts with GRX7 */ |
| 845 | AT91_PIOB 27 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB27 periph A, conflicts with G125CKO */ |
| 846 | }; |
| 847 | }; |
| 848 | |
| 849 | usart2 { |
| 850 | pinctrl_usart2: usart2-0 { |
| 851 | atmel,pins = |
| 852 | <AT91_PIOE 25 AT91_PERIPH_B AT91_PINCTRL_NONE /* PE25 periph B, conflicts with A25 */ |
| 853 | AT91_PIOE 26 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PE26 periph B with pullup, conflicts NCS0 */ |
| 854 | }; |
| 855 | |
| 856 | pinctrl_usart2_rts_cts: usart2_rts_cts-0 { |
| 857 | atmel,pins = |
| 858 | <AT91_PIOE 23 AT91_PERIPH_B AT91_PINCTRL_NONE /* PE23 periph B, conflicts with A23 */ |
| 859 | AT91_PIOE 24 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PE24 periph B, conflicts with A24 */ |
| 860 | }; |
| 861 | }; |
| 862 | |
| 863 | usart3 { |
| 864 | pinctrl_usart3: usart3-0 { |
| 865 | atmel,pins = |
| 866 | <AT91_PIOE 18 AT91_PERIPH_B AT91_PINCTRL_NONE /* PE18 periph B, conflicts with A18 */ |
| 867 | AT91_PIOE 19 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PE19 periph B with pullup, conflicts with A19 */ |
| 868 | }; |
| 869 | |
| 870 | pinctrl_usart3_rts_cts: usart3_rts_cts-0 { |
| 871 | atmel,pins = |
| 872 | <AT91_PIOE 16 AT91_PERIPH_B AT91_PINCTRL_NONE /* PE16 periph B, conflicts with A16 */ |
| 873 | AT91_PIOE 17 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PE17 periph B, conflicts with A17 */ |
| 874 | }; |
| 875 | }; |
| 876 | }; |
| 877 | |
| 878 | pioA: gpio@fffff200 { |
| 879 | compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; |
| 880 | reg = <0xfffff200 0x100>; |
| 881 | interrupts = <6 IRQ_TYPE_LEVEL_HIGH 1>; |
| 882 | #gpio-cells = <2>; |
| 883 | gpio-controller; |
| 884 | interrupt-controller; |
| 885 | #interrupt-cells = <2>; |
| 886 | clocks = <&pioA_clk>; |
| 887 | u-boot,dm-pre-reloc; |
| 888 | }; |
| 889 | |
| 890 | pioB: gpio@fffff400 { |
| 891 | compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; |
| 892 | reg = <0xfffff400 0x100>; |
| 893 | interrupts = <7 IRQ_TYPE_LEVEL_HIGH 1>; |
| 894 | #gpio-cells = <2>; |
| 895 | gpio-controller; |
| 896 | interrupt-controller; |
| 897 | #interrupt-cells = <2>; |
| 898 | clocks = <&pioB_clk>; |
| 899 | u-boot,dm-pre-reloc; |
| 900 | }; |
| 901 | |
| 902 | pioC: gpio@fffff600 { |
| 903 | compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; |
| 904 | reg = <0xfffff600 0x100>; |
| 905 | interrupts = <8 IRQ_TYPE_LEVEL_HIGH 1>; |
| 906 | #gpio-cells = <2>; |
| 907 | gpio-controller; |
| 908 | interrupt-controller; |
| 909 | #interrupt-cells = <2>; |
| 910 | clocks = <&pioC_clk>; |
| 911 | u-boot,dm-pre-reloc; |
| 912 | }; |
| 913 | |
| 914 | pioD: gpio@fffff800 { |
| 915 | compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; |
| 916 | reg = <0xfffff800 0x100>; |
| 917 | interrupts = <9 IRQ_TYPE_LEVEL_HIGH 1>; |
| 918 | #gpio-cells = <2>; |
| 919 | gpio-controller; |
| 920 | interrupt-controller; |
| 921 | #interrupt-cells = <2>; |
| 922 | clocks = <&pioD_clk>; |
| 923 | u-boot,dm-pre-reloc; |
| 924 | }; |
| 925 | |
| 926 | pioE: gpio@fffffa00 { |
| 927 | compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; |
| 928 | reg = <0xfffffa00 0x100>; |
| 929 | interrupts = <10 IRQ_TYPE_LEVEL_HIGH 1>; |
| 930 | #gpio-cells = <2>; |
| 931 | gpio-controller; |
| 932 | interrupt-controller; |
| 933 | #interrupt-cells = <2>; |
| 934 | clocks = <&pioE_clk>; |
| 935 | u-boot,dm-pre-reloc; |
| 936 | }; |
| 937 | |
| 938 | pmc: pmc@fffffc00 { |
| 939 | compatible = "atmel,sama5d3-pmc", "syscon"; |
| 940 | reg = <0xfffffc00 0x120>; |
| 941 | interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; |
| 942 | interrupt-controller; |
| 943 | #address-cells = <1>; |
| 944 | #size-cells = <0>; |
| 945 | #interrupt-cells = <1>; |
| 946 | u-boot,dm-pre-reloc; |
| 947 | |
| 948 | main_rc_osc: main_rc_osc { |
| 949 | compatible = "atmel,at91sam9x5-clk-main-rc-osc"; |
| 950 | #clock-cells = <0>; |
| 951 | interrupt-parent = <&pmc>; |
| 952 | interrupts = <AT91_PMC_MOSCRCS>; |
| 953 | clock-frequency = <12000000>; |
| 954 | clock-accuracy = <50000000>; |
| 955 | }; |
| 956 | |
| 957 | main_osc: main_osc { |
| 958 | compatible = "atmel,at91rm9200-clk-main-osc"; |
| 959 | #clock-cells = <0>; |
| 960 | interrupt-parent = <&pmc>; |
| 961 | interrupts = <AT91_PMC_MOSCS>; |
| 962 | clocks = <&main_xtal>; |
| 963 | }; |
| 964 | |
| 965 | main: mainck { |
| 966 | compatible = "atmel,at91sam9x5-clk-main"; |
| 967 | #clock-cells = <0>; |
| 968 | interrupt-parent = <&pmc>; |
| 969 | interrupts = <AT91_PMC_MOSCSELS>; |
| 970 | clocks = <&main_rc_osc &main_osc>; |
| 971 | }; |
| 972 | |
| 973 | plla: pllack@0 { |
| 974 | compatible = "atmel,sama5d3-clk-pll"; |
| 975 | #clock-cells = <0>; |
| 976 | interrupt-parent = <&pmc>; |
| 977 | interrupts = <AT91_PMC_LOCKA>; |
| 978 | clocks = <&main>; |
| 979 | reg = <0>; |
| 980 | atmel,clk-input-range = <8000000 50000000>; |
| 981 | #atmel,pll-clk-output-range-cells = <4>; |
| 982 | atmel,pll-clk-output-ranges = <400000000 1000000000 0 0>; |
| 983 | }; |
| 984 | |
| 985 | plladiv: plladivck { |
| 986 | compatible = "atmel,at91sam9x5-clk-plldiv"; |
| 987 | #clock-cells = <0>; |
| 988 | clocks = <&plla>; |
| 989 | }; |
| 990 | |
| 991 | utmi: utmick { |
| 992 | compatible = "atmel,at91sam9x5-clk-utmi"; |
| 993 | #clock-cells = <0>; |
| 994 | interrupt-parent = <&pmc>; |
| 995 | interrupts = <AT91_PMC_LOCKU>; |
| 996 | clocks = <&main>; |
Wenyou Yang | 56246d1 | 2017-09-05 18:30:08 +0800 | [diff] [blame] | 997 | regmap-sfr = <&sfr>; |
| 998 | u-boot,dm-pre-reloc; |
Wenyou Yang | 110fa97 | 2017-03-24 09:18:41 +0800 | [diff] [blame] | 999 | }; |
| 1000 | |
| 1001 | mck: masterck { |
| 1002 | compatible = "atmel,at91sam9x5-clk-master"; |
| 1003 | #clock-cells = <0>; |
| 1004 | interrupt-parent = <&pmc>; |
| 1005 | interrupts = <AT91_PMC_MCKRDY>; |
| 1006 | clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>; |
| 1007 | atmel,clk-output-range = <0 166000000>; |
| 1008 | atmel,clk-divisors = <1 2 4 3>; |
| 1009 | u-boot,dm-pre-reloc; |
| 1010 | }; |
| 1011 | |
| 1012 | usb: usbck { |
| 1013 | compatible = "atmel,at91sam9x5-clk-usb"; |
| 1014 | #clock-cells = <0>; |
| 1015 | clocks = <&plladiv>, <&utmi>; |
| 1016 | }; |
| 1017 | |
| 1018 | prog: progck { |
| 1019 | compatible = "atmel,at91sam9x5-clk-programmable"; |
| 1020 | #address-cells = <1>; |
| 1021 | #size-cells = <0>; |
| 1022 | interrupt-parent = <&pmc>; |
| 1023 | clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>; |
| 1024 | |
| 1025 | prog0: progck@0 { |
| 1026 | #clock-cells = <0>; |
| 1027 | reg = <0>; |
| 1028 | interrupts = <AT91_PMC_PCKRDY(0)>; |
| 1029 | }; |
| 1030 | |
| 1031 | prog1: progck@1 { |
| 1032 | #clock-cells = <0>; |
| 1033 | reg = <1>; |
| 1034 | interrupts = <AT91_PMC_PCKRDY(1)>; |
| 1035 | }; |
| 1036 | |
| 1037 | prog2: progck@2 { |
| 1038 | #clock-cells = <0>; |
| 1039 | reg = <2>; |
| 1040 | interrupts = <AT91_PMC_PCKRDY(2)>; |
| 1041 | }; |
| 1042 | }; |
| 1043 | |
| 1044 | smd: smdclk { |
| 1045 | compatible = "atmel,at91sam9x5-clk-smd"; |
| 1046 | #clock-cells = <0>; |
| 1047 | clocks = <&plladiv>, <&utmi>; |
| 1048 | }; |
| 1049 | |
| 1050 | systemck { |
| 1051 | compatible = "atmel,at91rm9200-clk-system"; |
| 1052 | #address-cells = <1>; |
| 1053 | #size-cells = <0>; |
| 1054 | |
| 1055 | ddrck: ddrck@2 { |
| 1056 | #clock-cells = <0>; |
| 1057 | reg = <2>; |
| 1058 | clocks = <&mck>; |
| 1059 | }; |
| 1060 | |
| 1061 | smdck: smdck@4 { |
| 1062 | #clock-cells = <0>; |
| 1063 | reg = <4>; |
| 1064 | clocks = <&smd>; |
| 1065 | }; |
| 1066 | |
| 1067 | uhpck: uhpck@6 { |
| 1068 | #clock-cells = <0>; |
| 1069 | reg = <6>; |
| 1070 | clocks = <&usb>; |
| 1071 | }; |
| 1072 | |
| 1073 | udpck: udpck@7 { |
| 1074 | #clock-cells = <0>; |
| 1075 | reg = <7>; |
| 1076 | clocks = <&usb>; |
| 1077 | }; |
| 1078 | |
| 1079 | pck0: pck@8 { |
| 1080 | #clock-cells = <0>; |
| 1081 | reg = <8>; |
| 1082 | clocks = <&prog0>; |
| 1083 | }; |
| 1084 | |
| 1085 | pck1: pck@9 { |
| 1086 | #clock-cells = <0>; |
| 1087 | reg = <9>; |
| 1088 | clocks = <&prog1>; |
| 1089 | }; |
| 1090 | |
| 1091 | pck2: pck@10 { |
| 1092 | #clock-cells = <0>; |
| 1093 | reg = <10>; |
| 1094 | clocks = <&prog2>; |
| 1095 | }; |
| 1096 | }; |
| 1097 | |
| 1098 | periphck { |
| 1099 | compatible = "atmel,at91sam9x5-clk-peripheral"; |
| 1100 | #address-cells = <1>; |
| 1101 | #size-cells = <0>; |
| 1102 | clocks = <&mck>; |
| 1103 | u-boot,dm-pre-reloc; |
| 1104 | |
| 1105 | dbgu_clk: dbgu_clk@2 { |
| 1106 | u-boot,dm-pre-reloc; |
| 1107 | #clock-cells = <0>; |
| 1108 | reg = <2>; |
| 1109 | }; |
| 1110 | |
| 1111 | hsmc_clk: hsmc_clk@5 { |
| 1112 | #clock-cells = <0>; |
| 1113 | reg = <5>; |
| 1114 | }; |
| 1115 | |
| 1116 | pioA_clk: pioA_clk@6 { |
| 1117 | u-boot,dm-pre-reloc; |
| 1118 | #clock-cells = <0>; |
| 1119 | reg = <6>; |
| 1120 | }; |
| 1121 | |
| 1122 | pioB_clk: pioB_clk@7 { |
| 1123 | u-boot,dm-pre-reloc; |
| 1124 | #clock-cells = <0>; |
| 1125 | reg = <7>; |
| 1126 | }; |
| 1127 | |
| 1128 | pioC_clk: pioC_clk@8 { |
| 1129 | u-boot,dm-pre-reloc; |
| 1130 | #clock-cells = <0>; |
| 1131 | reg = <8>; |
| 1132 | }; |
| 1133 | |
| 1134 | pioD_clk: pioD_clk@9 { |
| 1135 | u-boot,dm-pre-reloc; |
| 1136 | #clock-cells = <0>; |
| 1137 | reg = <9>; |
| 1138 | }; |
| 1139 | |
| 1140 | pioE_clk: pioE_clk@10 { |
| 1141 | u-boot,dm-pre-reloc; |
| 1142 | #clock-cells = <0>; |
| 1143 | reg = <10>; |
| 1144 | }; |
| 1145 | |
| 1146 | usart0_clk: usart0_clk@12 { |
| 1147 | #clock-cells = <0>; |
| 1148 | reg = <12>; |
| 1149 | atmel,clk-output-range = <0 66000000>; |
| 1150 | }; |
| 1151 | |
| 1152 | usart1_clk: usart1_clk@13 { |
| 1153 | #clock-cells = <0>; |
| 1154 | reg = <13>; |
| 1155 | atmel,clk-output-range = <0 66000000>; |
| 1156 | }; |
| 1157 | |
| 1158 | usart2_clk: usart2_clk@14 { |
| 1159 | #clock-cells = <0>; |
| 1160 | reg = <14>; |
| 1161 | atmel,clk-output-range = <0 66000000>; |
| 1162 | }; |
| 1163 | |
| 1164 | usart3_clk: usart3_clk@15 { |
| 1165 | #clock-cells = <0>; |
| 1166 | reg = <15>; |
| 1167 | atmel,clk-output-range = <0 66000000>; |
| 1168 | }; |
| 1169 | |
| 1170 | uart0_clk: uart0_clk@16 { |
| 1171 | #clock-cells = <0>; |
| 1172 | reg = <16>; |
| 1173 | atmel,clk-output-range = <0 66000000>; |
| 1174 | }; |
| 1175 | |
| 1176 | twi0_clk: twi0_clk@18 { |
| 1177 | reg = <18>; |
| 1178 | #clock-cells = <0>; |
| 1179 | atmel,clk-output-range = <0 16625000>; |
| 1180 | }; |
| 1181 | |
| 1182 | twi1_clk: twi1_clk@19 { |
| 1183 | #clock-cells = <0>; |
| 1184 | reg = <19>; |
| 1185 | atmel,clk-output-range = <0 16625000>; |
| 1186 | }; |
| 1187 | |
| 1188 | twi2_clk: twi2_clk@20 { |
| 1189 | #clock-cells = <0>; |
| 1190 | reg = <20>; |
| 1191 | atmel,clk-output-range = <0 16625000>; |
| 1192 | }; |
| 1193 | |
| 1194 | mci0_clk: mci0_clk@21 { |
| 1195 | u-boot,dm-pre-reloc; |
| 1196 | #clock-cells = <0>; |
| 1197 | reg = <21>; |
| 1198 | }; |
| 1199 | |
| 1200 | mci1_clk: mci1_clk@22 { |
| 1201 | u-boot,dm-pre-reloc; |
| 1202 | #clock-cells = <0>; |
| 1203 | reg = <22>; |
| 1204 | }; |
| 1205 | |
| 1206 | spi0_clk: spi0_clk@24 { |
| 1207 | u-boot,dm-pre-reloc; |
| 1208 | #clock-cells = <0>; |
| 1209 | reg = <24>; |
| 1210 | atmel,clk-output-range = <0 133000000>; |
| 1211 | }; |
| 1212 | |
| 1213 | spi1_clk: spi1_clk@25 { |
| 1214 | u-boot,dm-pre-reloc; |
| 1215 | #clock-cells = <0>; |
| 1216 | reg = <25>; |
| 1217 | atmel,clk-output-range = <0 133000000>; |
| 1218 | }; |
| 1219 | |
| 1220 | tcb0_clk: tcb0_clk@26 { |
| 1221 | #clock-cells = <0>; |
| 1222 | reg = <26>; |
| 1223 | atmel,clk-output-range = <0 133000000>; |
| 1224 | }; |
| 1225 | |
| 1226 | pwm_clk: pwm_clk@28 { |
| 1227 | #clock-cells = <0>; |
| 1228 | reg = <28>; |
| 1229 | }; |
| 1230 | |
| 1231 | adc_clk: adc_clk@29 { |
| 1232 | #clock-cells = <0>; |
| 1233 | reg = <29>; |
| 1234 | atmel,clk-output-range = <0 66000000>; |
| 1235 | }; |
| 1236 | |
| 1237 | dma0_clk: dma0_clk@30 { |
| 1238 | #clock-cells = <0>; |
| 1239 | reg = <30>; |
| 1240 | }; |
| 1241 | |
| 1242 | dma1_clk: dma1_clk@31 { |
| 1243 | #clock-cells = <0>; |
| 1244 | reg = <31>; |
| 1245 | }; |
| 1246 | |
| 1247 | uhphs_clk: uhphs_clk@32 { |
| 1248 | #clock-cells = <0>; |
| 1249 | reg = <32>; |
| 1250 | }; |
| 1251 | |
| 1252 | udphs_clk: udphs_clk@33 { |
| 1253 | #clock-cells = <0>; |
| 1254 | reg = <33>; |
| 1255 | }; |
| 1256 | |
| 1257 | isi_clk: isi_clk@37 { |
| 1258 | #clock-cells = <0>; |
| 1259 | reg = <37>; |
| 1260 | }; |
| 1261 | |
| 1262 | ssc0_clk: ssc0_clk@38 { |
| 1263 | #clock-cells = <0>; |
| 1264 | reg = <38>; |
| 1265 | atmel,clk-output-range = <0 66000000>; |
| 1266 | }; |
| 1267 | |
| 1268 | ssc1_clk: ssc1_clk@39 { |
| 1269 | #clock-cells = <0>; |
| 1270 | reg = <39>; |
| 1271 | atmel,clk-output-range = <0 66000000>; |
| 1272 | }; |
| 1273 | |
| 1274 | sha_clk: sha_clk@42 { |
| 1275 | #clock-cells = <0>; |
| 1276 | reg = <42>; |
| 1277 | }; |
| 1278 | |
| 1279 | aes_clk: aes_clk@43 { |
| 1280 | #clock-cells = <0>; |
| 1281 | reg = <43>; |
| 1282 | }; |
| 1283 | |
| 1284 | tdes_clk: tdes_clk@44 { |
| 1285 | #clock-cells = <0>; |
| 1286 | reg = <44>; |
| 1287 | }; |
| 1288 | |
| 1289 | trng_clk: trng_clk@45 { |
| 1290 | #clock-cells = <0>; |
| 1291 | reg = <45>; |
| 1292 | }; |
| 1293 | |
| 1294 | fuse_clk: fuse_clk@48 { |
| 1295 | #clock-cells = <0>; |
| 1296 | reg = <48>; |
| 1297 | }; |
| 1298 | |
| 1299 | mpddr_clk: mpddr_clk@49 { |
| 1300 | #clock-cells = <0>; |
| 1301 | reg = <49>; |
| 1302 | }; |
| 1303 | }; |
| 1304 | }; |
| 1305 | |
| 1306 | rstc@fffffe00 { |
| 1307 | compatible = "atmel,sama5d3-rstc", "atmel,at91sam9g45-rstc"; |
| 1308 | reg = <0xfffffe00 0x10>; |
| 1309 | clocks = <&clk32k>; |
| 1310 | }; |
| 1311 | |
| 1312 | shutdown-controller@fffffe10 { |
| 1313 | compatible = "atmel,at91sam9x5-shdwc"; |
| 1314 | reg = <0xfffffe10 0x10>; |
| 1315 | clocks = <&clk32k>; |
| 1316 | }; |
| 1317 | |
| 1318 | pit: timer@fffffe30 { |
| 1319 | compatible = "atmel,at91sam9260-pit"; |
| 1320 | reg = <0xfffffe30 0xf>; |
| 1321 | interrupts = <3 IRQ_TYPE_LEVEL_HIGH 5>; |
| 1322 | clocks = <&mck>; |
| 1323 | }; |
| 1324 | |
| 1325 | watchdog@fffffe40 { |
| 1326 | compatible = "atmel,at91sam9260-wdt"; |
| 1327 | reg = <0xfffffe40 0x10>; |
| 1328 | interrupts = <4 IRQ_TYPE_LEVEL_HIGH 7>; |
| 1329 | clocks = <&clk32k>; |
| 1330 | atmel,watchdog-type = "hardware"; |
| 1331 | atmel,reset-type = "all"; |
| 1332 | atmel,dbg-halt; |
| 1333 | status = "disabled"; |
| 1334 | }; |
| 1335 | |
| 1336 | sckc@fffffe50 { |
| 1337 | compatible = "atmel,at91sam9x5-sckc"; |
| 1338 | reg = <0xfffffe50 0x4>; |
| 1339 | |
| 1340 | slow_rc_osc: slow_rc_osc { |
| 1341 | compatible = "atmel,at91sam9x5-clk-slow-rc-osc"; |
| 1342 | #clock-cells = <0>; |
| 1343 | clock-frequency = <32768>; |
| 1344 | clock-accuracy = <50000000>; |
| 1345 | atmel,startup-time-usec = <75>; |
| 1346 | }; |
| 1347 | |
| 1348 | slow_osc: slow_osc { |
| 1349 | compatible = "atmel,at91sam9x5-clk-slow-osc"; |
| 1350 | #clock-cells = <0>; |
| 1351 | clocks = <&slow_xtal>; |
| 1352 | atmel,startup-time-usec = <1200000>; |
| 1353 | }; |
| 1354 | |
| 1355 | clk32k: slowck { |
| 1356 | compatible = "atmel,at91sam9x5-clk-slow"; |
| 1357 | #clock-cells = <0>; |
| 1358 | clocks = <&slow_rc_osc &slow_osc>; |
| 1359 | }; |
| 1360 | }; |
| 1361 | |
| 1362 | rtc@fffffeb0 { |
| 1363 | compatible = "atmel,at91rm9200-rtc"; |
| 1364 | reg = <0xfffffeb0 0x30>; |
| 1365 | interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; |
| 1366 | clocks = <&clk32k>; |
| 1367 | }; |
| 1368 | }; |
| 1369 | |
| 1370 | usb0: gadget@00500000 { |
| 1371 | #address-cells = <1>; |
| 1372 | #size-cells = <0>; |
| 1373 | compatible = "atmel,sama5d3-udc"; |
| 1374 | reg = <0x00500000 0x100000 |
| 1375 | 0xf8030000 0x4000>; |
| 1376 | interrupts = <33 IRQ_TYPE_LEVEL_HIGH 2>; |
| 1377 | clocks = <&udphs_clk>, <&utmi>; |
| 1378 | clock-names = "pclk", "hclk"; |
| 1379 | status = "disabled"; |
| 1380 | |
| 1381 | ep0: endpoint@0 { |
| 1382 | reg = <0>; |
| 1383 | atmel,fifo-size = <64>; |
| 1384 | atmel,nb-banks = <1>; |
| 1385 | }; |
| 1386 | |
| 1387 | ep1: endpoint@1 { |
| 1388 | reg = <1>; |
| 1389 | atmel,fifo-size = <1024>; |
| 1390 | atmel,nb-banks = <3>; |
| 1391 | atmel,can-dma; |
| 1392 | atmel,can-isoc; |
| 1393 | }; |
| 1394 | |
| 1395 | ep2: endpoint@2 { |
| 1396 | reg = <2>; |
| 1397 | atmel,fifo-size = <1024>; |
| 1398 | atmel,nb-banks = <3>; |
| 1399 | atmel,can-dma; |
| 1400 | atmel,can-isoc; |
| 1401 | }; |
| 1402 | |
| 1403 | ep3: endpoint@3 { |
| 1404 | reg = <3>; |
| 1405 | atmel,fifo-size = <1024>; |
| 1406 | atmel,nb-banks = <2>; |
| 1407 | atmel,can-dma; |
| 1408 | }; |
| 1409 | |
| 1410 | ep4: endpoint@4 { |
| 1411 | reg = <4>; |
| 1412 | atmel,fifo-size = <1024>; |
| 1413 | atmel,nb-banks = <2>; |
| 1414 | atmel,can-dma; |
| 1415 | }; |
| 1416 | |
| 1417 | ep5: endpoint@5 { |
| 1418 | reg = <5>; |
| 1419 | atmel,fifo-size = <1024>; |
| 1420 | atmel,nb-banks = <2>; |
| 1421 | atmel,can-dma; |
| 1422 | }; |
| 1423 | |
| 1424 | ep6: endpoint@6 { |
| 1425 | reg = <6>; |
| 1426 | atmel,fifo-size = <1024>; |
| 1427 | atmel,nb-banks = <2>; |
| 1428 | atmel,can-dma; |
| 1429 | }; |
| 1430 | |
| 1431 | ep7i: endpoint@7 { |
| 1432 | reg = <7>; |
| 1433 | atmel,fifo-size = <1024>; |
| 1434 | atmel,nb-banks = <2>; |
| 1435 | atmel,can-dma; |
| 1436 | }; |
| 1437 | |
| 1438 | ep8: endpoint@8 { |
| 1439 | reg = <8>; |
| 1440 | atmel,fifo-size = <1024>; |
| 1441 | atmel,nb-banks = <2>; |
| 1442 | }; |
| 1443 | |
| 1444 | ep9: endpoint@9 { |
| 1445 | reg = <9>; |
| 1446 | atmel,fifo-size = <1024>; |
| 1447 | atmel,nb-banks = <2>; |
| 1448 | }; |
| 1449 | |
Eugen Hristev | c260cb2 | 2020-06-05 09:51:31 +0300 | [diff] [blame] | 1450 | ep10: endpoint@a { |
Wenyou Yang | 110fa97 | 2017-03-24 09:18:41 +0800 | [diff] [blame] | 1451 | reg = <10>; |
| 1452 | atmel,fifo-size = <1024>; |
| 1453 | atmel,nb-banks = <2>; |
| 1454 | }; |
| 1455 | |
Eugen Hristev | c260cb2 | 2020-06-05 09:51:31 +0300 | [diff] [blame] | 1456 | ep11: endpoint@b { |
Wenyou Yang | 110fa97 | 2017-03-24 09:18:41 +0800 | [diff] [blame] | 1457 | reg = <11>; |
| 1458 | atmel,fifo-size = <1024>; |
| 1459 | atmel,nb-banks = <2>; |
| 1460 | }; |
| 1461 | |
Eugen Hristev | c260cb2 | 2020-06-05 09:51:31 +0300 | [diff] [blame] | 1462 | ep12: endpoint@c { |
Wenyou Yang | 110fa97 | 2017-03-24 09:18:41 +0800 | [diff] [blame] | 1463 | reg = <12>; |
| 1464 | atmel,fifo-size = <1024>; |
| 1465 | atmel,nb-banks = <2>; |
| 1466 | }; |
| 1467 | |
Eugen Hristev | c260cb2 | 2020-06-05 09:51:31 +0300 | [diff] [blame] | 1468 | ep13: endpoint@d { |
Wenyou Yang | 110fa97 | 2017-03-24 09:18:41 +0800 | [diff] [blame] | 1469 | reg = <13>; |
| 1470 | atmel,fifo-size = <1024>; |
| 1471 | atmel,nb-banks = <2>; |
| 1472 | }; |
| 1473 | |
Eugen Hristev | c260cb2 | 2020-06-05 09:51:31 +0300 | [diff] [blame] | 1474 | ep14: endpoint@e { |
Wenyou Yang | 110fa97 | 2017-03-24 09:18:41 +0800 | [diff] [blame] | 1475 | reg = <14>; |
| 1476 | atmel,fifo-size = <1024>; |
| 1477 | atmel,nb-banks = <2>; |
| 1478 | }; |
| 1479 | |
Eugen Hristev | c260cb2 | 2020-06-05 09:51:31 +0300 | [diff] [blame] | 1480 | ep15: endpoint@f { |
Wenyou Yang | 110fa97 | 2017-03-24 09:18:41 +0800 | [diff] [blame] | 1481 | reg = <15>; |
| 1482 | atmel,fifo-size = <1024>; |
| 1483 | atmel,nb-banks = <2>; |
| 1484 | }; |
| 1485 | }; |
| 1486 | |
| 1487 | usb1: ohci@00600000 { |
| 1488 | compatible = "atmel,at91rm9200-ohci", "usb-ohci"; |
| 1489 | reg = <0x00600000 0x100000>; |
| 1490 | interrupts = <32 IRQ_TYPE_LEVEL_HIGH 2>; |
| 1491 | clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>; |
| 1492 | clock-names = "ohci_clk", "hclk", "uhpck"; |
| 1493 | status = "disabled"; |
| 1494 | }; |
| 1495 | |
| 1496 | usb2: ehci@00700000 { |
| 1497 | compatible = "atmel,at91sam9g45-ehci", "usb-ehci"; |
| 1498 | reg = <0x00700000 0x100000>; |
| 1499 | interrupts = <32 IRQ_TYPE_LEVEL_HIGH 2>; |
| 1500 | clocks = <&utmi>, <&uhphs_clk>; |
| 1501 | clock-names = "usb_clk", "ehci_clk"; |
| 1502 | status = "disabled"; |
| 1503 | }; |
| 1504 | |
| 1505 | nand0: nand@60000000 { |
| 1506 | compatible = "atmel,at91rm9200-nand"; |
| 1507 | #address-cells = <1>; |
| 1508 | #size-cells = <1>; |
| 1509 | ranges; |
| 1510 | reg = < 0x60000000 0x01000000 /* EBI CS3 */ |
| 1511 | 0xffffc070 0x00000490 /* SMC PMECC regs */ |
| 1512 | 0xffffc500 0x00000100 /* SMC PMECC Error Location regs */ |
| 1513 | 0x00110000 0x00018000 /* ROM code */ |
| 1514 | >; |
| 1515 | interrupts = <5 IRQ_TYPE_LEVEL_HIGH 6>; |
| 1516 | atmel,nand-addr-offset = <21>; |
| 1517 | atmel,nand-cmd-offset = <22>; |
| 1518 | atmel,nand-has-dma; |
| 1519 | pinctrl-names = "default"; |
| 1520 | pinctrl-0 = <&pinctrl_nand0_ale_cle>; |
| 1521 | atmel,pmecc-lookup-table-offset = <0x0 0x8000>; |
| 1522 | status = "disabled"; |
| 1523 | |
| 1524 | nfc@70000000 { |
| 1525 | compatible = "atmel,sama5d3-nfc"; |
| 1526 | #address-cells = <1>; |
| 1527 | #size-cells = <1>; |
| 1528 | reg = < |
| 1529 | 0x70000000 0x08000000 /* NFC Command Registers */ |
| 1530 | 0xffffc000 0x00000070 /* NFC HSMC regs */ |
| 1531 | 0x00200000 0x00100000 /* NFC SRAM banks */ |
| 1532 | >; |
| 1533 | clocks = <&hsmc_clk>; |
| 1534 | }; |
| 1535 | }; |
| 1536 | }; |
Eugen Hristev | 2b238c6 | 2018-09-18 10:35:54 +0300 | [diff] [blame] | 1537 | |
| 1538 | onewire_tm: onewire { |
| 1539 | compatible = "w1-gpio"; |
| 1540 | status = "disabled"; |
| 1541 | }; |
Wenyou Yang | 110fa97 | 2017-03-24 09:18:41 +0800 | [diff] [blame] | 1542 | }; |