board/davinci/dm355evm/dm355evm.c

/*
 * Copyright (C) 2009 David Brownell
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <nand.h>
#include <asm/io.h>
#include <asm/arch/hardware.h>
#include <asm/arch/emif_defs.h>
#include <asm/arch/nand_defs.h>
#include <asm/arch/davinci_misc.h>
#include <net.h>
#include <netdev.h>
#ifdef CONFIG_DAVINCI_MMC
#include <mmc.h>
#include <asm/arch/sdmmc_defs.h>
#endif

DECLARE_GLOBAL_DATA_PTR;

/*
 * With the DM355 EVM, u-boot is *always* a third stage loader,
 * unless a JTAG debugger handles the first two stages:
 *
 *   - 1st stage is ROM Boot Loader (RBL), which searches for a
 *     second stage loader in one of three places based on SW7:
 *     NAND (with MMC/SD fallback), MMC/SD, or UART.
 *
 *   - 2nd stage is User Boot Loader (UBL), using at most 30KB
 *     of on-chip SRAM, responsible for lowlevel init, and for
 *     loading the third stage loader into DRAM.
 *
 *   - 3rd stage, that's us!
 */

int board_init(void)
{
	gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DM355_EVM;
	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;

	/* We expect the UBL to have handled "lowlevel init", which
	 * involves setting up at least:
	 *  - clocks
	 *      + PLL1 (for ARM and peripherals) and PLL2 (for DDR)
	 *      + clock divisors for those PLLs
	 *      + LPSC_DDR module enabled
	 *      + LPSC_TIMER0 module (still) enabled
	 *  - EMIF
	 *      + DDR init and timings
	 *      + AEMIF timings (for NAND and DM9000)
	 *  - pinmux
	 *
	 * Some of that is repeated here, mostly as a precaution.
	 */

	/* AEMIF:  Some "address" lines are available as GPIOs.  A3..A13
	 * could be too if we used A12 as a GPIO during NAND chipselect
	 * (and Linux did too), letting us control the LED on A7/GPIO61.
	 */
	REG(PINMUX2) = 0x0c08;

	/* UART0 may still be in SyncReset if we didn't boot from UART */
	davinci_enable_uart0();

	/* EDMA may be in SyncReset too; turn it on, Linux won't (yet) */
	lpsc_on(DAVINCI_LPSC_TPCC);
	lpsc_on(DAVINCI_LPSC_TPTC0);
	lpsc_on(DAVINCI_LPSC_TPTC1);

	return 0;
}

#ifdef CONFIG_DRIVER_DM9000
int board_eth_init(bd_t *bis)
{
	return dm9000_initialize(bis);
}
#endif

#ifdef CONFIG_NAND_DAVINCI

static void nand_dm355evm_select_chip(struct mtd_info *mtd, int chip)
{
	struct nand_chip	*this = mtd->priv;
	unsigned long		wbase = (unsigned long) this->IO_ADDR_W;
	unsigned long		rbase = (unsigned long) this->IO_ADDR_R;

	if (chip == 1) {
		__set_bit(14, &wbase);
		__set_bit(14, &rbase);
	} else {
		__clear_bit(14, &wbase);
		__clear_bit(14, &rbase);
	}
	this->IO_ADDR_W = (void *)wbase;
	this->IO_ADDR_R = (void *)rbase;
}

int board_nand_init(struct nand_chip *nand)
{
	davinci_nand_init(nand);
	nand->select_chip = nand_dm355evm_select_chip;
	return 0;
}

#endif

#ifdef CONFIG_DAVINCI_MMC
static struct davinci_mmc mmc_sd0 = {
	.reg_base	= (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
	.input_clk	= 108000000,
	.host_caps	= MMC_MODE_4BIT,
	.voltages	= MMC_VDD_32_33 | MMC_VDD_33_34,
	.version	= MMC_CTLR_VERSION_1,
};

#ifdef CONFIG_DAVINCI_MMC_SD1
static struct davinci_mmc mmc_sd1 = {
	.reg_base	= (struct davinci_mmc_regs *)DAVINCI_MMC_SD1_BASE,
	.input_clk	= 108000000,
	.host_caps	= MMC_MODE_4BIT,
	.voltages	= MMC_VDD_32_33 | MMC_VDD_33_34,
	.version	= MMC_CTLR_VERSION_1,
};
#endif

int board_mmc_init(bd_t *bis)
{
	int err;

	/* Add slot-0 to mmc subsystem */
	err = davinci_mmc_init(bis, &mmc_sd0);
	if (err)
		return err;

#ifdef CONFIG_DAVINCI_MMC_SD1
	/* Add slot-1 to mmc subsystem */
	err = davinci_mmc_init(bis, &mmc_sd1);
#endif

	return err;
}
#endif