board/omap2420h4/mem.c

/*
 * (C) Copyright 2004
 * Texas Instruments, <www.ti.com>
 * Richard Woodruff <r-woodruff2@ti.com>
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

#include <common.h>
#include <asm/arch/omap2420.h>
#include <asm/io.h>
#include <asm/arch/bits.h>
#include <asm/arch/mux.h>
#include <asm/arch/mem.h>
#include <asm/arch/clocks.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/sys_info.h>

/************************************************************
 * sdelay() - simple spin loop.  Will be constant time as
 *  its generally used in 12MHz bypass conditions only.  This
 *  is necessary until timers are accessible.
 *
 *  not inline to increase chances its in cache when called
 *************************************************************/
void sdelay (unsigned long loops)
{
	__asm__ volatile ("1:\n"
					  "subs %0, %1, #1\n"
					  "bne 1b":"=r" (loops):"0" (loops));
}

/*********************************************************************************
 * prcm_init() - inits clocks for PRCM as defined in clocks.h (config II default).
 *   -- called from SRAM, or Flash (using temp SRAM stack).
 *********************************************************************************/
void prcm_init(void)
{
	u32 rev,div;
#ifdef CONFIG_PARTIAL_SRAM
	void (*f_lock_pll) (u32, u32, u32, u32);
	extern void *_end_vect, *_start;

	f_lock_pll = (void *)((u32)&_end_vect - (u32)&_start + SRAM_VECT_CODE);
#endif

	__raw_writel(0, CM_FCLKEN1_CORE);	   /* stop all clocks to reduce ringing */
	__raw_writel(0, CM_FCLKEN2_CORE);	   /* may not be necessary */
	__raw_writel(0, CM_ICLKEN1_CORE);
	__raw_writel(0, CM_ICLKEN2_CORE);

	__raw_writel(DPLL_OUT, CM_CLKSEL2_PLL);	/* set DPLL out */
	__raw_writel(MPU_DIV, CM_CLKSEL_MPU);	/* set MPU divider */
	__raw_writel(DSP_DIV, CM_CLKSEL_DSP);	/* set dsp and iva dividers */
	__raw_writel(GFX_DIV, CM_CLKSEL_GFX);	/* set gfx dividers */

	rev  = get_cpu_rev();
	if (rev == CPU_2420_ES1 || rev ==  CPU_2422_ES1)
		div = BUS_DIV_ES1;
	else
		div	= BUS_DIV;
	__raw_writel(div, CM_CLKSEL1_CORE);/* set L3/L4/USB/Display/Vlnc/SSi dividers */
	sdelay(1000);

#ifndef CONFIG_PARTIAL_SRAM
	/* If running fully from SRAM this is OK.  The Flash bus drops out for just a little.
	 * but then comes back.  If running from Flash this sequence kills you, thus you need
	 * to run it using CONFIG_PARTIAL_SRAM.
	 */
	__raw_writel(MODE_BYPASS_FAST, CM_CLKEN_PLL); /* go to bypass, fast relock */
	wait_on_value(BIT0|BIT1, BIT1, CM_IDLEST_CKGEN, LDELAY); /* wait till in bypass */

	/* set clock selection and dpll dividers. */
	__raw_writel(DPLL_VAL, CM_CLKSEL1_PLL);	 /* set pll for target rate */
	__raw_writel(COMMIT_DIVIDERS, PRCM_CLKCFG_CTRL); /* commit dividers */
	sdelay(10000);
	__raw_writel(DPLL_LOCK, CM_CLKEN_PLL); /* enable dpll */
	sdelay(10000);
	wait_on_value(BIT0|BIT1, BIT2, CM_IDLEST_CKGEN, LDELAY);  /*wait for dpll lock */
#else
/* if running from flash, need to jump to small relocated code area in SRAM.
 * This is the only safe spot to do configurations from.
 */
	(*f_lock_pll)(PRCM_CLKCFG_CTRL, CM_CLKEN_PLL, DPLL_LOCK, CM_IDLEST_CKGEN);
#endif

	__raw_writel(DPLL_LOCK|APLL_LOCK, CM_CLKEN_PLL);   /* enable apll */
	wait_on_value(BIT8, BIT8, CM_IDLEST_CKGEN, LDELAY);	/* wait for apll lock */
	sdelay(1000);
}

/***********************************************
 * memif_init() - init the gpmc and sdrc
 *  - early init routines, called from flash or
 *  SRAM.
 ***********************************************/
void memif_init(void)
{
	sdrc_init();
#ifndef CONFIG_PARTIAL_SRAM  /* don't init if calling from flash */
	gpmc_init();
#endif
}

/********************************************************
 *  mem_ok() - test used to see if timings are correct
 *             for a part. Helps in gussing which part
 *             we are currently using.
 *******************************************************/
u32 mem_ok(void)
{  u32 val;
	__raw_writel(0x0,OMAP2420_SDRC_CS0+0x400);  /* clear pos A */
	__raw_writel(0x12345678, OMAP2420_SDRC_CS0);/* pattern to pos B */
	val = __raw_readl(OMAP2420_SDRC_CS0+0x400); /* get pos A value */
	if (val != 0)                               /* see if pos A value changed*/
		return(0);
	else
		return(1);
}

/********************************************************
 *  sdrc_init() - init the sdrc chip selects CS0 and CS1
 *  - early init routines, called from flash or
 *  SRAM.
 *******************************************************/
void sdrc_init(void)
{
	#define EARLY_INIT 1
	do_sdrc_init(SDRC_CS0_OSET, EARLY_INIT);  /* only init up first bank here */
}

/**********************************************************
 * do_sdrc_init(): initialize the SDRAM for use.
 *  -called from low level code with stack only.
 *  -code sets up SDRAM timing and muxing for 2422 or 2420.
 *  -optimal settings can be placed here, or redone after i2c
 *      inspection of board info
 *
 * !!! When ES1 comes out need to conditionalize RFR value!!!
 **********************************************************/
void do_sdrc_init(u32 offset, u32 early)
{
	u32 cpu, bug=0, rev, shared=0, cs0=0, pmask=0,first=1;
	sdrc_data_t *sdata;	 /* do not change type */

	static const sdrc_data_t sdrc_2422 =
	{
		H4_2422_SDRC_SHARING, H4_2422_SDRC_MDCFG_0, H4_2422_SDRC_ACTIM_CTRLA_0,
		H4_2422_SDRC_ACTIM_CTRLB_0, H4_2422_SDRC_RFR_CTRL_ES1, H4_2422_SDRC_MR_0,
		H4_2422_SDRC_DLLA_CTRL, H4_2422_SDRC_DLLB_CTRL
	};
	static const sdrc_data_t sdrc_2420 =
	{
		H4_2420_SDRC_SHARING, H4_2420_SDRC_MDCFG_0, H4_2420_SDRC_ACTIM_CTRLA_0,
		H4_2420_SDRC_ACTIM_CTRLB_0, H4_2420_SDRC_RFR_CTRL_ES1, H4_2420_SDRC_MR_0,
		H4_2420_SDRC_DLLA_CTRL, H4_2420_SDRC_DLLB_CTRL
	};

	if (offset == SDRC_CS0_OSET)
		cs0 = shared = 1;  /* int regs shared between both chip select */

	cpu = get_cpu_type();

	/* warning generated, though code generation is correct. this may bite later, but is ok for now.
	 *  there is only so much C code you can do on stack only operation.
	 */
	if (cpu == CPU_2422)
		sdata = &sdrc_2422;
	else
		sdata = &sdrc_2420;
	__asm__ __volatile__("": : :"memory");
#ifdef CONFIG_PARTIAL_SRAM
	/* u-boot is compiled to run in DDR at 8xxxxxxx.  If we use data here which is not pc relative
	 * we need to get the address correct.  We need to find the current flash mapping to dress up
	 * the initial pointer load.  As long as this is const data we should be ok.
	 */
	if(early)
		sdata = (sdrc_data_t *)(((u32)sdata & 0x0003FFFF) | get_gpmc0_base());
#endif

	men_combo:

	if (!early && get_mem_type() == DDR_COMBO) { /* combo part has a shared CKE signal, can't use feature */
		pmask = BIT2;
		first = 0;	/* trigger ddr_combo init */
	}

	if (shared) {
		__raw_writel(__raw_readl(SMS_SYSCONFIG)|SMART_IDLE, SMS_SYSCONFIG);
		__raw_writel(SMART_IDLE|SOFTRESET, SDRC_SYSCONFIG);	/* reset sdrc */
		wait_on_value(BIT0, BIT0, SDRC_STATUS, 12000000);	/* wait till reset done set */
		__raw_writel(SMART_IDLE, SDRC_SYSCONFIG);		/* clear soft reset */
		__raw_writel(sdata->sdrc_sharing, SDRC_SHARING);
		__raw_writel((__raw_readl(SDRC_POWER)|SMART_IDLE) & ~pmask, SDRC_POWER);
	}
	if (first)
		__raw_writel(sdata->sdrc_mdcfg_0, SDRC_MCFG_0+offset);
	else {
		__raw_writel((__raw_readl(SDRC_POWER)|SMART_IDLE) & ~pmask, SDRC_POWER);
		__raw_writel(H4_2420_COMBO_MDCFG_0,SDRC_MCFG_0+offset);
	}

	if (cs0) {
		__raw_writel(sdata->sdrc_actim_ctrla_0, SDRC_ACTIM_CTRLA_0);
		__raw_writel(sdata->sdrc_actim_ctrlb_0, SDRC_ACTIM_CTRLB_0);
	} else {
		__raw_writel(sdata->sdrc_actim_ctrla_0, SDRC_ACTIM_CTRLA_1);
		__raw_writel(sdata->sdrc_actim_ctrlb_0, SDRC_ACTIM_CTRLB_1);
	}

	__raw_writel(sdata->sdrc_rfr_ctrl, SDRC_RFR_CTRL+offset);

	/* init sequence for _mDDR_ using manual commands (DDR is a bit different) */
	__raw_writel(CMD_NOP, SDRC_MANUAL_0+offset);
	sdelay(5000);  /* susposed to be 100us per design spec for mddr*/
	__raw_writel(CMD_PRECHARGE, SDRC_MANUAL_0+offset);
	__raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0+offset);
	__raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0+offset);

	/*
	 * CSx SDRC Mode Register
	 * Burst length = 4 - DDR memory
	 * Serial mode
	 * CAS latency = x
	 */
	__raw_writel(sdata->sdrc_mr_0, SDRC_MR_0+offset);

	/* NOTE: ES1 242x _BUG_ DLL */
	rev  = get_cpu_rev();
	if (rev == CPU_2420_ES1 || rev ==  CPU_2422_ES1)
		bug = BIT0;
	/* enable & load up DLL with good value for 75MHz, and set phase to 90% */
	if (shared) {
		__raw_writel(sdata->sdrc_dlla_ctrl, SDRC_DLLA_CTRL);
		__raw_writel(sdata->sdrc_dlla_ctrl & ~(BIT2|bug), SDRC_DLLA_CTRL);
		__raw_writel(sdata->sdrc_dllb_ctrl, SDRC_DLLB_CTRL);
		__raw_writel(sdata->sdrc_dllb_ctrl & ~(BIT2|bug) , SDRC_DLLB_CTRL);
	}
	sdelay(9000);
	if (!first || mem_ok())	/* passed test or 2nd bank init */
		return;
	else {
		first = 0;
		goto men_combo;
	}
}


/*****************************************************
 * gpmc_init(): init gpmc bus
 * Init GPMC for x16, MuxMode (SDRAM in x32).
 * This code can only be executed from SRAM or SDRAM.
 *****************************************************/
void gpmc_init(void)
{
	u32 mux=0, mtype, mwidth;

	/* global settings */
	__raw_writel(0x10, GPMC_SYSCONFIG);	/* smart idle */
	__raw_writel(0x0, GPMC_IRQENABLE);	/* isr's sources masked */
	__raw_writel(0x1, GPMC_TIMEOUT_CONTROL);/* timeout disable */
	__raw_writel(0x111, GPMC_CONFIG);	/* set nWP, disable limited addr */

	/* discover bus connection from sysboot */
	if (is_gpmc_muxed() == GPMC_MUXED)
		mux = BIT9;
	mtype = get_gpmc0_type();
	mwidth = get_gpmc0_width();

	/* setup cs0 */
	__raw_writel(0x0, GPMC_CONFIG7_0);	/* disable current map */
	sdelay(1000);
	__raw_writel(H4_24XX_GPMC_CONFIG1_0|mux|mtype|mwidth, GPMC_CONFIG1_0);
	//__raw_writel(H4_24XX_GPMC_CONFIG2_0, GPMC_CONFIG2_0);
	__raw_writel(H4_24XX_GPMC_CONFIG3_0, GPMC_CONFIG3_0);
	__raw_writel(H4_24XX_GPMC_CONFIG4_0, GPMC_CONFIG4_0);
	//__raw_writel(H4_24XX_GPMC_CONFIG5_0, GPMC_CONFIG5_0);
	__raw_writel(H4_24XX_GPMC_CONFIG7_0, GPMC_CONFIG7_0);/* enable new mapping */
	sdelay(2000);

	/* setup cs1 */
	__raw_writel(0, GPMC_CONFIG7_1); /* disable any mapping */
	sdelay(1000);
	__raw_writel(H4_24XX_GPMC_CONFIG1_1|mux, GPMC_CONFIG1_1);
	__raw_writel(H4_24XX_GPMC_CONFIG2_1, GPMC_CONFIG2_1);
	__raw_writel(H4_24XX_GPMC_CONFIG3_1, GPMC_CONFIG3_1);
	__raw_writel(H4_24XX_GPMC_CONFIG4_1, GPMC_CONFIG4_1);
	__raw_writel(H4_24XX_GPMC_CONFIG5_1, GPMC_CONFIG5_1);
	__raw_writel(H4_24XX_GPMC_CONFIG6_1, GPMC_CONFIG6_1);
	__raw_writel(H4_24XX_GPMC_CONFIG7_1, GPMC_CONFIG7_1); /* enable mapping */
	sdelay(2000);
}