blob: c10a79c83930bde4c8e4d451b4a879fd6c0c41f9 [file] [log] [blame]
wdenkfe8c2802002-11-03 00:38:21 +00001/*
2 * MPC8xx Communication Processor Module.
3 * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
4 *
Wolfgang Denk8cba0902006-05-12 16:15:46 +02005 * (C) Copyright 2000-2006
wdenkd4ca31c2004-01-02 14:00:00 +00006 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
7 *
wdenkfe8c2802002-11-03 00:38:21 +00008 * This file contains structures and information for the communication
9 * processor channels. Some CPM control and status is available
10 * throught the MPC8xx internal memory map. See immap.h for details.
11 * This file only contains what I need for the moment, not the total
12 * CPM capabilities. I (or someone else) will add definitions as they
13 * are needed. -- Dan
14 *
15 * On the MBX board, EPPC-Bug loads CPM microcode into the first 512
16 * bytes of the DP RAM and relocates the I2C parameter area to the
17 * IDMA1 space. The remaining DP RAM is available for buffer descriptors
18 * or other use.
19 */
20#ifndef __CPM_8XX__
21#define __CPM_8XX__
22
wdenkfe8c2802002-11-03 00:38:21 +000023#include <asm/8xx_immap.h>
24
25/* CPM Command register.
26*/
wdenk7c7a23b2002-12-07 00:20:59 +000027#define CPM_CR_RST ((ushort)0x8000)
28#define CPM_CR_OPCODE ((ushort)0x0f00)
29#define CPM_CR_CHAN ((ushort)0x00f0)
30#define CPM_CR_FLG ((ushort)0x0001)
wdenkfe8c2802002-11-03 00:38:21 +000031
32/* Some commands (there are more...later)
33*/
34#define CPM_CR_INIT_TRX ((ushort)0x0000)
35#define CPM_CR_INIT_RX ((ushort)0x0001)
36#define CPM_CR_INIT_TX ((ushort)0x0002)
37#define CPM_CR_HUNT_MODE ((ushort)0x0003)
38#define CPM_CR_STOP_TX ((ushort)0x0004)
39#define CPM_CR_RESTART_TX ((ushort)0x0006)
40#define CPM_CR_SET_GADDR ((ushort)0x0008)
41
42/* Channel numbers.
43*/
wdenk7c7a23b2002-12-07 00:20:59 +000044#define CPM_CR_CH_SCC1 ((ushort)0x0000)
45#define CPM_CR_CH_I2C ((ushort)0x0001) /* I2C and IDMA1 */
46#define CPM_CR_CH_SCC2 ((ushort)0x0004)
47#define CPM_CR_CH_SPI ((ushort)0x0005) /* SPI/IDMA2/Timers */
48#define CPM_CR_CH_SCC3 ((ushort)0x0008)
49#define CPM_CR_CH_SMC1 ((ushort)0x0009) /* SMC1 / DSP1 */
50#define CPM_CR_CH_SCC4 ((ushort)0x000c)
51#define CPM_CR_CH_SMC2 ((ushort)0x000d) /* SMC2 / DSP2 */
wdenkfe8c2802002-11-03 00:38:21 +000052
53#define mk_cr_cmd(CH, CMD) ((CMD << 8) | (CH << 4))
54
55/*
56 * DPRAM defines and allocation functions
57 */
58
59/* The dual ported RAM is multi-functional. Some areas can be (and are
60 * being) used for microcode. There is an area that can only be used
61 * as data ram for buffer descriptors, which is all we use right now.
62 * Currently the first 512 and last 256 bytes are used for microcode.
63 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020064#ifdef CONFIG_SYS_ALLOC_DPRAM
wdenkfe8c2802002-11-03 00:38:21 +000065
66#define CPM_DATAONLY_BASE ((uint)0x0800)
67#define CPM_DATAONLY_SIZE ((uint)0x0700)
68#define CPM_DP_NOSPACE ((uint)0x7fffffff)
69
70#else
71
72#define CPM_SERIAL_BASE 0x0800
73#define CPM_I2C_BASE 0x0820
74#define CPM_SPI_BASE 0x0840
75#define CPM_FEC_BASE 0x0860
wdenk79536a62004-09-27 20:20:11 +000076#define CPM_SERIAL2_BASE 0x08E0
wdenkfe8c2802002-11-03 00:38:21 +000077#define CPM_SCC_BASE 0x0900
78#define CPM_POST_BASE 0x0980
wdenk281e00a2004-08-01 22:48:16 +000079#define CPM_WLKBD_BASE 0x0a00
wdenkfe8c2802002-11-03 00:38:21 +000080
81#endif
82
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020083#ifndef CONFIG_SYS_CPM_POST_WORD_ADDR
wdenkfe8c2802002-11-03 00:38:21 +000084#define CPM_POST_WORD_ADDR 0x07FC
wdenkea909b72002-11-21 23:11:29 +000085#else
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020086#define CPM_POST_WORD_ADDR CONFIG_SYS_CPM_POST_WORD_ADDR
wdenkea909b72002-11-21 23:11:29 +000087#endif
wdenkfe8c2802002-11-03 00:38:21 +000088
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020089#ifndef CONFIG_SYS_CPM_BOOTCOUNT_ADDR
wdenkbdccc4f2003-08-05 17:43:17 +000090#define CPM_BOOTCOUNT_ADDR (CPM_POST_WORD_ADDR - 2*sizeof(ulong))
91#else
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020092#define CPM_BOOTCOUNT_ADDR CONFIG_SYS_CPM_BOOTCOUNT_ADDR
wdenkbdccc4f2003-08-05 17:43:17 +000093#endif
94
wdenkfe8c2802002-11-03 00:38:21 +000095#define BD_IIC_START ((uint) 0x0400) /* <- please use CPM_I2C_BASE !! */
96
97/* Export the base address of the communication processor registers
98 * and dual port ram.
99 */
100extern cpm8xx_t *cpmp; /* Pointer to comm processor */
101
102/* Buffer descriptors used by many of the CPM protocols.
103*/
104typedef struct cpm_buf_desc {
105 ushort cbd_sc; /* Status and Control */
106 ushort cbd_datlen; /* Data length in buffer */
107 uint cbd_bufaddr; /* Buffer address in host memory */
108} cbd_t;
109
Mike Williams16263082011-07-22 04:01:30 +0000110#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */
wdenkfe8c2802002-11-03 00:38:21 +0000111#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */
112#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */
113#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */
114#define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */
115#define BD_SC_TC ((ushort)0x0400) /* Transmit CRC */
116#define BD_SC_CM ((ushort)0x0200) /* Continous mode */
117#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */
118#define BD_SC_P ((ushort)0x0100) /* xmt preamble */
119#define BD_SC_BR ((ushort)0x0020) /* Break received */
120#define BD_SC_FR ((ushort)0x0010) /* Framing error */
121#define BD_SC_PR ((ushort)0x0008) /* Parity error */
122#define BD_SC_OV ((ushort)0x0002) /* Overrun */
123#define BD_SC_CD ((ushort)0x0001) /* Carrier Detect lost */
124
125/* Parameter RAM offsets.
126*/
127#define PROFF_SCC1 ((uint)0x0000)
128#define PROFF_IIC ((uint)0x0080)
Scott Wooda166fbc2013-05-17 20:01:54 -0500129#define PROFF_REVNUM ((uint)0x00b0)
wdenkfe8c2802002-11-03 00:38:21 +0000130#define PROFF_SCC2 ((uint)0x0100)
131#define PROFF_SPI ((uint)0x0180)
132#define PROFF_SCC3 ((uint)0x0200)
133#define PROFF_SMC1 ((uint)0x0280)
134#define PROFF_SCC4 ((uint)0x0300)
135#define PROFF_SMC2 ((uint)0x0380)
136
137/* Define enough so I can at least use the serial port as a UART.
138 * The MBX uses SMC1 as the host serial port.
139 */
140typedef struct smc_uart {
141 ushort smc_rbase; /* Rx Buffer descriptor base address */
142 ushort smc_tbase; /* Tx Buffer descriptor base address */
143 u_char smc_rfcr; /* Rx function code */
144 u_char smc_tfcr; /* Tx function code */
145 ushort smc_mrblr; /* Max receive buffer length */
146 uint smc_rstate; /* Internal */
147 uint smc_idp; /* Internal */
148 ushort smc_rbptr; /* Internal */
149 ushort smc_ibc; /* Internal */
150 uint smc_rxtmp; /* Internal */
151 uint smc_tstate; /* Internal */
152 uint smc_tdp; /* Internal */
153 ushort smc_tbptr; /* Internal */
154 ushort smc_tbc; /* Internal */
155 uint smc_txtmp; /* Internal */
156 ushort smc_maxidl; /* Maximum idle characters */
157 ushort smc_tmpidl; /* Temporary idle counter */
158 ushort smc_brklen; /* Last received break length */
159 ushort smc_brkec; /* rcv'd break condition counter */
160 ushort smc_brkcr; /* xmt break count register */
161 ushort smc_rmask; /* Temporary bit mask */
Heiko Schocherb423d052008-01-11 01:12:07 +0100162 u_char res1[8];
163 ushort smc_rpbase; /* Relocation pointer */
wdenkfe8c2802002-11-03 00:38:21 +0000164} smc_uart_t;
165
166/* Function code bits.
167*/
168#define SMC_EB ((u_char)0x10) /* Set big endian byte order */
169
170/* SMC uart mode register.
171*/
172#define SMCMR_REN ((ushort)0x0001)
173#define SMCMR_TEN ((ushort)0x0002)
174#define SMCMR_DM ((ushort)0x000c)
175#define SMCMR_SM_GCI ((ushort)0x0000)
176#define SMCMR_SM_UART ((ushort)0x0020)
177#define SMCMR_SM_TRANS ((ushort)0x0030)
178#define SMCMR_SM_MASK ((ushort)0x0030)
179#define SMCMR_PM_EVEN ((ushort)0x0100) /* Even parity, else odd */
180#define SMCMR_REVD SMCMR_PM_EVEN
181#define SMCMR_PEN ((ushort)0x0200) /* Parity enable */
182#define SMCMR_BS SMCMR_PEN
183#define SMCMR_SL ((ushort)0x0400) /* Two stops, else one */
184#define SMCR_CLEN_MASK ((ushort)0x7800) /* Character length */
185#define smcr_mk_clen(C) (((C) << 11) & SMCR_CLEN_MASK)
186
187/* SMC2 as Centronics parallel printer. It is half duplex, in that
188 * it can only receive or transmit. The parameter ram values for
189 * each direction are either unique or properly overlap, so we can
190 * include them in one structure.
191 */
192typedef struct smc_centronics {
193 ushort scent_rbase;
194 ushort scent_tbase;
195 u_char scent_cfcr;
196 u_char scent_smask;
197 ushort scent_mrblr;
198 uint scent_rstate;
199 uint scent_r_ptr;
200 ushort scent_rbptr;
201 ushort scent_r_cnt;
202 uint scent_rtemp;
203 uint scent_tstate;
204 uint scent_t_ptr;
205 ushort scent_tbptr;
206 ushort scent_t_cnt;
207 uint scent_ttemp;
208 ushort scent_max_sl;
209 ushort scent_sl_cnt;
210 ushort scent_character1;
211 ushort scent_character2;
212 ushort scent_character3;
213 ushort scent_character4;
214 ushort scent_character5;
215 ushort scent_character6;
216 ushort scent_character7;
217 ushort scent_character8;
218 ushort scent_rccm;
219 ushort scent_rccr;
220} smc_cent_t;
221
222/* Centronics Status Mask Register.
223*/
224#define SMC_CENT_F ((u_char)0x08)
225#define SMC_CENT_PE ((u_char)0x04)
226#define SMC_CENT_S ((u_char)0x02)
227
228/* SMC Event and Mask register.
229*/
230#define SMCM_BRKE ((unsigned char)0x40) /* When in UART Mode */
231#define SMCM_BRK ((unsigned char)0x10) /* When in UART Mode */
232#define SMCM_TXE ((unsigned char)0x10) /* When in Transparent Mode */
233#define SMCM_BSY ((unsigned char)0x04)
234#define SMCM_TX ((unsigned char)0x02)
235#define SMCM_RX ((unsigned char)0x01)
236
237/* Baud rate generators.
238*/
239#define CPM_BRG_RST ((uint)0x00020000)
240#define CPM_BRG_EN ((uint)0x00010000)
241#define CPM_BRG_EXTC_INT ((uint)0x00000000)
242#define CPM_BRG_EXTC_CLK2 ((uint)0x00004000)
243#define CPM_BRG_EXTC_CLK6 ((uint)0x00008000)
244#define CPM_BRG_ATB ((uint)0x00002000)
245#define CPM_BRG_CD_MASK ((uint)0x00001ffe)
246#define CPM_BRG_DIV16 ((uint)0x00000001)
247
248/* SI Clock Route Register
249*/
250#define SICR_RCLK_SCC1_BRG1 ((uint)0x00000000)
251#define SICR_TCLK_SCC1_BRG1 ((uint)0x00000000)
252#define SICR_RCLK_SCC2_BRG2 ((uint)0x00000800)
253#define SICR_TCLK_SCC2_BRG2 ((uint)0x00000100)
254#define SICR_RCLK_SCC3_BRG3 ((uint)0x00100000)
255#define SICR_TCLK_SCC3_BRG3 ((uint)0x00020000)
256#define SICR_RCLK_SCC4_BRG4 ((uint)0x18000000)
257#define SICR_TCLK_SCC4_BRG4 ((uint)0x03000000)
258
259/* SCCs.
260*/
261#define SCC_GSMRH_IRP ((uint)0x00040000)
262#define SCC_GSMRH_GDE ((uint)0x00010000)
263#define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000)
264#define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000)
265#define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000)
266#define SCC_GSMRH_REVD ((uint)0x00002000)
267#define SCC_GSMRH_TRX ((uint)0x00001000)
268#define SCC_GSMRH_TTX ((uint)0x00000800)
269#define SCC_GSMRH_CDP ((uint)0x00000400)
270#define SCC_GSMRH_CTSP ((uint)0x00000200)
271#define SCC_GSMRH_CDS ((uint)0x00000100)
272#define SCC_GSMRH_CTSS ((uint)0x00000080)
273#define SCC_GSMRH_TFL ((uint)0x00000040)
274#define SCC_GSMRH_RFW ((uint)0x00000020)
275#define SCC_GSMRH_TXSY ((uint)0x00000010)
276#define SCC_GSMRH_SYNL16 ((uint)0x0000000c)
277#define SCC_GSMRH_SYNL8 ((uint)0x00000008)
278#define SCC_GSMRH_SYNL4 ((uint)0x00000004)
279#define SCC_GSMRH_RTSM ((uint)0x00000002)
280#define SCC_GSMRH_RSYN ((uint)0x00000001)
281
282#define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */
283#define SCC_GSMRL_EDGE_NONE ((uint)0x60000000)
284#define SCC_GSMRL_EDGE_NEG ((uint)0x40000000)
285#define SCC_GSMRL_EDGE_POS ((uint)0x20000000)
286#define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000)
287#define SCC_GSMRL_TCI ((uint)0x10000000)
288#define SCC_GSMRL_TSNC_3 ((uint)0x0c000000)
289#define SCC_GSMRL_TSNC_4 ((uint)0x08000000)
290#define SCC_GSMRL_TSNC_14 ((uint)0x04000000)
291#define SCC_GSMRL_TSNC_INF ((uint)0x00000000)
292#define SCC_GSMRL_RINV ((uint)0x02000000)
293#define SCC_GSMRL_TINV ((uint)0x01000000)
294#define SCC_GSMRL_TPL_128 ((uint)0x00c00000)
295#define SCC_GSMRL_TPL_64 ((uint)0x00a00000)
296#define SCC_GSMRL_TPL_48 ((uint)0x00800000)
297#define SCC_GSMRL_TPL_32 ((uint)0x00600000)
298#define SCC_GSMRL_TPL_16 ((uint)0x00400000)
299#define SCC_GSMRL_TPL_8 ((uint)0x00200000)
300#define SCC_GSMRL_TPL_NONE ((uint)0x00000000)
301#define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000)
302#define SCC_GSMRL_TPP_01 ((uint)0x00100000)
303#define SCC_GSMRL_TPP_10 ((uint)0x00080000)
304#define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000)
305#define SCC_GSMRL_TEND ((uint)0x00040000)
306#define SCC_GSMRL_TDCR_32 ((uint)0x00030000)
307#define SCC_GSMRL_TDCR_16 ((uint)0x00020000)
308#define SCC_GSMRL_TDCR_8 ((uint)0x00010000)
309#define SCC_GSMRL_TDCR_1 ((uint)0x00000000)
310#define SCC_GSMRL_RDCR_32 ((uint)0x0000c000)
311#define SCC_GSMRL_RDCR_16 ((uint)0x00008000)
312#define SCC_GSMRL_RDCR_8 ((uint)0x00004000)
313#define SCC_GSMRL_RDCR_1 ((uint)0x00000000)
314#define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000)
315#define SCC_GSMRL_RENC_MANCH ((uint)0x00002000)
316#define SCC_GSMRL_RENC_FM0 ((uint)0x00001000)
317#define SCC_GSMRL_RENC_NRZI ((uint)0x00000800)
318#define SCC_GSMRL_RENC_NRZ ((uint)0x00000000)
319#define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600)
320#define SCC_GSMRL_TENC_MANCH ((uint)0x00000400)
321#define SCC_GSMRL_TENC_FM0 ((uint)0x00000200)
322#define SCC_GSMRL_TENC_NRZI ((uint)0x00000100)
323#define SCC_GSMRL_TENC_NRZ ((uint)0x00000000)
324#define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */
325#define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080)
326#define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040)
327#define SCC_GSMRL_DIAG_NORM ((uint)0x00000000)
328#define SCC_GSMRL_ENR ((uint)0x00000020)
329#define SCC_GSMRL_ENT ((uint)0x00000010)
330#define SCC_GSMRL_MODE_ENET ((uint)0x0000000c)
331#define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009)
332#define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008)
333#define SCC_GSMRL_MODE_V14 ((uint)0x00000007)
334#define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006)
335#define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005)
336#define SCC_GSMRL_MODE_UART ((uint)0x00000004)
337#define SCC_GSMRL_MODE_SS7 ((uint)0x00000003)
338#define SCC_GSMRL_MODE_ATALK ((uint)0x00000002)
339#define SCC_GSMRL_MODE_HDLC ((uint)0x00000000)
340
341#define SCC_TODR_TOD ((ushort)0x8000)
342
343/* SCC Event and Mask register.
344*/
345#define SCCM_TXE ((unsigned char)0x10)
346#define SCCM_BSY ((unsigned char)0x04)
347#define SCCM_TX ((unsigned char)0x02)
348#define SCCM_RX ((unsigned char)0x01)
349
350typedef struct scc_param {
351 ushort scc_rbase; /* Rx Buffer descriptor base address */
352 ushort scc_tbase; /* Tx Buffer descriptor base address */
353 u_char scc_rfcr; /* Rx function code */
354 u_char scc_tfcr; /* Tx function code */
355 ushort scc_mrblr; /* Max receive buffer length */
356 uint scc_rstate; /* Internal */
357 uint scc_idp; /* Internal */
358 ushort scc_rbptr; /* Internal */
359 ushort scc_ibc; /* Internal */
360 uint scc_rxtmp; /* Internal */
361 uint scc_tstate; /* Internal */
362 uint scc_tdp; /* Internal */
363 ushort scc_tbptr; /* Internal */
364 ushort scc_tbc; /* Internal */
365 uint scc_txtmp; /* Internal */
366 uint scc_rcrc; /* Internal */
367 uint scc_tcrc; /* Internal */
368} sccp_t;
369
370/* Function code bits.
371*/
372#define SCC_EB ((u_char)0x10) /* Set big endian byte order */
373
374/* CPM Ethernet through SCCx.
375 */
376typedef struct scc_enet {
377 sccp_t sen_genscc;
378 uint sen_cpres; /* Preset CRC */
379 uint sen_cmask; /* Constant mask for CRC */
380 uint sen_crcec; /* CRC Error counter */
381 uint sen_alec; /* alignment error counter */
382 uint sen_disfc; /* discard frame counter */
383 ushort sen_pads; /* Tx short frame pad character */
384 ushort sen_retlim; /* Retry limit threshold */
385 ushort sen_retcnt; /* Retry limit counter */
386 ushort sen_maxflr; /* maximum frame length register */
387 ushort sen_minflr; /* minimum frame length register */
388 ushort sen_maxd1; /* maximum DMA1 length */
389 ushort sen_maxd2; /* maximum DMA2 length */
390 ushort sen_maxd; /* Rx max DMA */
391 ushort sen_dmacnt; /* Rx DMA counter */
392 ushort sen_maxb; /* Max BD byte count */
393 ushort sen_gaddr1; /* Group address filter */
394 ushort sen_gaddr2;
395 ushort sen_gaddr3;
396 ushort sen_gaddr4;
397 uint sen_tbuf0data0; /* Save area 0 - current frame */
398 uint sen_tbuf0data1; /* Save area 1 - current frame */
399 uint sen_tbuf0rba; /* Internal */
400 uint sen_tbuf0crc; /* Internal */
401 ushort sen_tbuf0bcnt; /* Internal */
402 ushort sen_paddrh; /* physical address (MSB) */
403 ushort sen_paddrm;
404 ushort sen_paddrl; /* physical address (LSB) */
405 ushort sen_pper; /* persistence */
406 ushort sen_rfbdptr; /* Rx first BD pointer */
407 ushort sen_tfbdptr; /* Tx first BD pointer */
408 ushort sen_tlbdptr; /* Tx last BD pointer */
409 uint sen_tbuf1data0; /* Save area 0 - current frame */
410 uint sen_tbuf1data1; /* Save area 1 - current frame */
411 uint sen_tbuf1rba; /* Internal */
412 uint sen_tbuf1crc; /* Internal */
413 ushort sen_tbuf1bcnt; /* Internal */
414 ushort sen_txlen; /* Tx Frame length counter */
415 ushort sen_iaddr1; /* Individual address filter */
416 ushort sen_iaddr2;
417 ushort sen_iaddr3;
418 ushort sen_iaddr4;
419 ushort sen_boffcnt; /* Backoff counter */
420
421 /* NOTE: Some versions of the manual have the following items
422 * incorrectly documented. Below is the proper order.
423 */
424 ushort sen_taddrh; /* temp address (MSB) */
425 ushort sen_taddrm;
426 ushort sen_taddrl; /* temp address (LSB) */
427} scc_enet_t;
428
429/**********************************************************************
430 *
431 * Board specific configuration settings.
432 *
433 * Please note that we use the presence of a #define SCC_ENET and/or
434 * #define FEC_ENET to enable the SCC resp. FEC ethernet drivers.
435 **********************************************************************/
436
437
438/*** ADS *************************************************************/
439
440#if defined(CONFIG_MPC860) && defined(CONFIG_ADS)
441/* This ENET stuff is for the MPC860ADS with ethernet on SCC1.
442 */
443
444#define PROFF_ENET PROFF_SCC1
445#define CPM_CR_ENET CPM_CR_CH_SCC1
446#define SCC_ENET 0
447
448#define PA_ENET_RXD ((ushort)0x0001)
449#define PA_ENET_TXD ((ushort)0x0002)
450#define PA_ENET_TCLK ((ushort)0x0100)
451#define PA_ENET_RCLK ((ushort)0x0200)
452
453#define PB_ENET_TENA ((uint)0x00001000)
454
455#define PC_ENET_CLSN ((ushort)0x0010)
456#define PC_ENET_RENA ((ushort)0x0020)
457
458#define SICR_ENET_MASK ((uint)0x000000ff)
459#define SICR_ENET_CLKRT ((uint)0x0000002c)
460
461/* 68160 PHY control */
462
463#define PC_ENET_ETHLOOP ((ushort)0x0800)
464#define PC_ENET_TPFLDL ((ushort)0x0400)
465#define PC_ENET_TPSQEL ((ushort)0x0200)
466
467#endif /* MPC860ADS */
468
wdenkfe8c2802002-11-03 00:38:21 +0000469/*** BSEIP **********************************************************/
470
471#ifdef CONFIG_BSEIP
472/* This ENET stuff is for the MPC823 with ethernet on SCC2.
473 * This is unique to the BSE ip-Engine board.
474 */
475#define PROFF_ENET PROFF_SCC2
476#define CPM_CR_ENET CPM_CR_CH_SCC2
477#define SCC_ENET 1
478#define PA_ENET_RXD ((ushort)0x0004)
479#define PA_ENET_TXD ((ushort)0x0008)
480#define PA_ENET_TCLK ((ushort)0x0100)
481#define PA_ENET_RCLK ((ushort)0x0200)
482#define PB_ENET_TENA ((uint)0x00002000)
483#define PC_ENET_CLSN ((ushort)0x0040)
484#define PC_ENET_RENA ((ushort)0x0080)
485
486/* BSE uses port B and C bits for PHY control also.
487*/
488#define PB_BSE_POWERUP ((uint)0x00000004)
489#define PB_BSE_FDXDIS ((uint)0x00008000)
490#define PC_BSE_LOOPBACK ((ushort)0x0800)
491
492#define SICR_ENET_MASK ((uint)0x0000ff00)
493#define SICR_ENET_CLKRT ((uint)0x00002c00)
494#endif /* CONFIG_BSEIP */
495
496/*** BSEIP **********************************************************/
497
498#ifdef CONFIG_FLAGADM
499/* Enet configuration for the FLAGADM */
500/* Enet on SCC2 */
501
502#define PROFF_ENET PROFF_SCC2
503#define CPM_CR_ENET CPM_CR_CH_SCC2
504#define SCC_ENET 1
wdenk7c7a23b2002-12-07 00:20:59 +0000505#define PA_ENET_RXD ((ushort)0x0004)
506#define PA_ENET_TXD ((ushort)0x0008)
wdenkfe8c2802002-11-03 00:38:21 +0000507#define PA_ENET_TCLK ((ushort)0x0100)
508#define PA_ENET_RCLK ((ushort)0x0400)
509#define PB_ENET_TENA ((uint)0x00002000)
510#define PC_ENET_CLSN ((ushort)0x0040)
511#define PC_ENET_RENA ((ushort)0x0080)
512
513#define SICR_ENET_MASK ((uint)0x0000ff00)
514#define SICR_ENET_CLKRT ((uint)0x00003400)
515#endif /* CONFIG_FLAGADM */
516
wdenk3bac3512003-03-12 10:41:04 +0000517/*** ELPT860 *********************************************************/
518
519#ifdef CONFIG_ELPT860
520/* Bits in parallel I/O port registers that have to be set/cleared
521 * to configure the pins for SCC1 use.
522 */
523# define PROFF_ENET PROFF_SCC1
524# define CPM_CR_ENET CPM_CR_CH_SCC1
525# define SCC_ENET 0
526
527# define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
528# define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
529# define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
530# define PA_ENET_TCLK ((ushort)0x0200) /* PA 6 */
531
532# define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
533# define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
534# define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
535
536/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK1) to
537 * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
538 */
539# define SICR_ENET_MASK ((uint)0x000000FF)
540# define SICR_ENET_CLKRT ((uint)0x00000025)
541#endif /* CONFIG_ELPT860 */
542
wdenkfe8c2802002-11-03 00:38:21 +0000543/*** ESTEEM 192E **************************************************/
544#ifdef CONFIG_ESTEEM192E
545/* ESTEEM192E
546 * This ENET stuff is for the MPC850 with ethernet on SCC2. This
547 * is very similar to the RPX-Lite configuration.
548 * Note TENA , LOOPBACK , FDPLEX_DIS on Port B.
549 */
550
551#define PROFF_ENET PROFF_SCC2
552#define CPM_CR_ENET CPM_CR_CH_SCC2
553#define SCC_ENET 1
554
555#define PA_ENET_RXD ((ushort)0x0004)
556#define PA_ENET_TXD ((ushort)0x0008)
557#define PA_ENET_TCLK ((ushort)0x0200)
558#define PA_ENET_RCLK ((ushort)0x0800)
559#define PB_ENET_TENA ((uint)0x00002000)
560#define PC_ENET_CLSN ((ushort)0x0040)
561#define PC_ENET_RENA ((ushort)0x0080)
562
563#define SICR_ENET_MASK ((uint)0x0000ff00)
564#define SICR_ENET_CLKRT ((uint)0x00003d00)
565
566#define PB_ENET_LOOPBACK ((uint)0x00004000)
567#define PB_ENET_FDPLEX_DIS ((uint)0x00008000)
568
569#endif
570
571/*** FADS823 ********************************************************/
572
573#if defined(CONFIG_MPC823FADS) && defined(CONFIG_FADS)
574/* This ENET stuff is for the MPC823FADS with ethernet on SCC2.
575 */
576#ifdef CONFIG_SCC2_ENET
577#define PROFF_ENET PROFF_SCC2
578#define CPM_CR_ENET CPM_CR_CH_SCC2
579#define SCC_ENET 1
580#define CPMVEC_ENET CPMVEC_SCC2
581#endif
582
583#ifdef CONFIG_SCC1_ENET
584#define PROFF_ENET PROFF_SCC1
585#define CPM_CR_ENET CPM_CR_CH_SCC1
586#define SCC_ENET 0
587#define CPMVEC_ENET CPMVEC_SCC1
588#endif
589
590#define PA_ENET_RXD ((ushort)0x0004)
591#define PA_ENET_TXD ((ushort)0x0008)
592#define PA_ENET_TCLK ((ushort)0x0400)
593#define PA_ENET_RCLK ((ushort)0x0200)
594
595#define PB_ENET_TENA ((uint)0x00002000)
596
597#define PC_ENET_CLSN ((ushort)0x0040)
598#define PC_ENET_RENA ((ushort)0x0080)
599
600#define SICR_ENET_MASK ((uint)0x0000ff00)
601#define SICR_ENET_CLKRT ((uint)0x00002e00)
602
603#endif /* CONFIG_FADS823FADS */
604
605/*** FADS850SAR ********************************************************/
606
607#if defined(CONFIG_MPC850SAR) && defined(CONFIG_FADS)
608/* This ENET stuff is for the MPC850SAR with ethernet on SCC2. Some of
609 * this may be unique to the FADS850SAR configuration.
610 * Note TENA is on Port B.
611 */
612#define PROFF_ENET PROFF_SCC2
613#define CPM_CR_ENET CPM_CR_CH_SCC2
614#define SCC_ENET 1
615#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
616#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
617#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
618#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
619#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
620#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
621#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
622
623#define SICR_ENET_MASK ((uint)0x0000ff00)
624#define SICR_ENET_CLKRT ((uint)0x00002f00) /* RCLK-CLK2, TCLK-CLK4 */
625#endif /* CONFIG_FADS850SAR */
626
627/*** FADS860T********************************************************/
628
wdenk180d3f72004-01-04 16:28:35 +0000629#if defined(CONFIG_FADS) && defined(CONFIG_MPC86x)
630/*
631 * This ENET stuff is for the MPC86xFADS/MPC8xxADS with ethernet on SCC1.
wdenkfe8c2802002-11-03 00:38:21 +0000632 */
wdenkfe8c2802002-11-03 00:38:21 +0000633#ifdef CONFIG_SCC1_ENET
wdenk180d3f72004-01-04 16:28:35 +0000634
wdenkfe8c2802002-11-03 00:38:21 +0000635#define SCC_ENET 0
wdenk180d3f72004-01-04 16:28:35 +0000636
wdenkfe8c2802002-11-03 00:38:21 +0000637#define PROFF_ENET PROFF_SCC1
638#define CPM_CR_ENET CPM_CR_CH_SCC1
639
640#define PA_ENET_RXD ((ushort)0x0001)
641#define PA_ENET_TXD ((ushort)0x0002)
642#define PA_ENET_TCLK ((ushort)0x0100)
643#define PA_ENET_RCLK ((ushort)0x0200)
644
645#define PB_ENET_TENA ((uint)0x00001000)
646
647#define PC_ENET_CLSN ((ushort)0x0010)
648#define PC_ENET_RENA ((ushort)0x0020)
649
650#define SICR_ENET_MASK ((uint)0x000000ff)
651#define SICR_ENET_CLKRT ((uint)0x0000002c)
652
wdenk180d3f72004-01-04 16:28:35 +0000653#endif /* CONFIG_SCC1_ETHERNET */
654
655/*
wdenk11142572004-06-06 21:35:06 +0000656 * This ENET stuff is for the MPC860TFADS/MPC86xADS/MPC885ADS
657 * with ethernet on FEC.
wdenkfe8c2802002-11-03 00:38:21 +0000658 */
659
660#ifdef CONFIG_FEC_ENET
wdenk180d3f72004-01-04 16:28:35 +0000661#define FEC_ENET /* Use FEC for Ethernet */
662#endif /* CONFIG_FEC_ENET */
wdenkfe8c2802002-11-03 00:38:21 +0000663
wdenk180d3f72004-01-04 16:28:35 +0000664#endif /* CONFIG_FADS && CONFIG_MPC86x */
wdenkfe8c2802002-11-03 00:38:21 +0000665
wdenk384ae022002-11-05 00:17:55 +0000666/*** FPS850L, FPS860L ************************************************/
wdenkfe8c2802002-11-03 00:38:21 +0000667
wdenk384ae022002-11-05 00:17:55 +0000668#if defined(CONFIG_FPS850L) || defined(CONFIG_FPS860L)
wdenkfe8c2802002-11-03 00:38:21 +0000669/* Bits in parallel I/O port registers that have to be set/cleared
wdenk384ae022002-11-05 00:17:55 +0000670 * to configure the pins for SCC2 use.
wdenkfe8c2802002-11-03 00:38:21 +0000671 */
672#define PROFF_ENET PROFF_SCC2
673#define CPM_CR_ENET CPM_CR_CH_SCC2
674#define SCC_ENET 1
675#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
676#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
677#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
678#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
679
680#define PC_ENET_TENA ((ushort)0x0002) /* PC 14 */
681#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
682#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
683
684/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
685 * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
686 */
687#define SICR_ENET_MASK ((uint)0x0000ff00)
688#define SICR_ENET_CLKRT ((uint)0x00002600)
wdenk384ae022002-11-05 00:17:55 +0000689#endif /* CONFIG_FPS850L, CONFIG_FPS860L */
wdenkfe8c2802002-11-03 00:38:21 +0000690
691/*** GEN860T **********************************************************/
692#if defined(CONFIG_GEN860T)
693#undef SCC_ENET
694#define FEC_ENET
695
Wolfgang Denk53677ef2008-05-20 16:00:29 +0200696#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
697#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
698#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
699#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
700#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
701#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
702#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
703#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
704#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
705#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
706#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
707#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
708#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
wdenkfe8c2802002-11-03 00:38:21 +0000709#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3-15 */
710#endif /* CONFIG_GEN860T */
711
712/*** GENIETV ********************************************************/
713
714#if defined(CONFIG_GENIETV)
715/* Ethernet is only on SCC2 */
716
717#define CONFIG_SCC2_ENET
718#define PROFF_ENET PROFF_SCC2
719#define CPM_CR_ENET CPM_CR_CH_SCC2
720#define SCC_ENET 1
721#define CPMVEC_ENET CPMVEC_SCC2
722
723#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
724#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
725#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
726#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
727
728#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
729
730#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
731#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
732
733#define SICR_ENET_MASK ((uint)0x0000ff00)
734#define SICR_ENET_CLKRT ((uint)0x00002e00)
735
736#endif /* CONFIG_GENIETV */
737
wdenkfe8c2802002-11-03 00:38:21 +0000738/*** HERMES-PRO ******************************************************/
739
740/* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */
741
742#ifdef CONFIG_HERMES
743
744#define FEC_ENET /* use FEC for EThernet */
745#undef SCC_ENET
746
747
748#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
749#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
750#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
751#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
752#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
753#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
754#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
755#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
756#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
757#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
758#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
759#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
760#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
761
762#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
763
764#endif /* CONFIG_HERMES */
765
wdenkfe8c2802002-11-03 00:38:21 +0000766/*** ICU862 **********************************************************/
767
768#if defined(CONFIG_ICU862)
769
770#ifdef CONFIG_FEC_ENET
771#define FEC_ENET /* use FEC for EThernet */
772#endif /* CONFIG_FEC_ETHERNET */
773
774#endif /* CONFIG_ICU862 */
775
776/*** IP860 **********************************************************/
777
778#if defined(CONFIG_IP860)
779/* Bits in parallel I/O port registers that have to be set/cleared
780 * to configure the pins for SCC1 use.
781 */
782#define PROFF_ENET PROFF_SCC1
783#define CPM_CR_ENET CPM_CR_CH_SCC1
784#define SCC_ENET 0
785#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
786#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
787#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
788#define PA_ENET_TCLK ((ushort)0x0100) /* PA 7 */
789
790#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
791#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
792#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
793
794#define PB_ENET_RESET (uint)0x00000008 /* PB 28 */
795#define PB_ENET_JABD (uint)0x00000004 /* PB 29 */
796
797/* Control bits in the SICR to route TCLK (CLK1) and RCLK (CLK2) to
798 * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
799 */
800#define SICR_ENET_MASK ((uint)0x000000ff)
801#define SICR_ENET_CLKRT ((uint)0x0000002C)
802#endif /* CONFIG_IP860 */
803
804/*** IVMS8 **********************************************************/
805
806/* The IVMS8 uses the FEC on a MPC860T for Ethernet */
807
808#if defined(CONFIG_IVMS8) || defined(CONFIG_IVML24)
809
810#define FEC_ENET /* use FEC for EThernet */
811#undef SCC_ENET
812
813#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */
814
815#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */
816
817#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
818#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
819#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
820#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
821#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
822#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
823#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
824#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
825#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
826#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
827#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
828#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
829#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
830
831#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
832
833#endif /* CONFIG_IVMS8, CONFIG_IVML24 */
834
wdenk0608e042004-03-25 19:29:38 +0000835/*** KUP4K, KUP4X ****************************************************/
836/* The KUP4 boards uses the FEC on a MPC8xx for Ethernet */
wdenk56f94be2002-11-05 16:35:14 +0000837
wdenk0608e042004-03-25 19:29:38 +0000838#if defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
wdenk56f94be2002-11-05 16:35:14 +0000839
840#define FEC_ENET /* use FEC for EThernet */
841#undef SCC_ENET
842
843#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */
844
845#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */
846
847#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
848#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
849#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
850#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
851#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
852#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
853#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
854#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
855#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
856#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
857#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
858#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
859#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
860
861#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
862
863#endif /* CONFIG_KUP4K */
864
wdenkfe8c2802002-11-03 00:38:21 +0000865/*** LWMON **********************************************************/
866
wdenk281e00a2004-08-01 22:48:16 +0000867#if defined(CONFIG_LWMON)
wdenkfe8c2802002-11-03 00:38:21 +0000868/* Bits in parallel I/O port registers that have to be set/cleared
869 * to configure the pins for SCC2 use.
870 */
871#define PROFF_ENET PROFF_SCC2
872#define CPM_CR_ENET CPM_CR_CH_SCC2
873#define SCC_ENET 1
874#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
875#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
876#define PA_ENET_RCLK ((ushort)0x0800) /* PA 4 */
877#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
878
879#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
880
881#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
882#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
883
884/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK4) to
885 * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
886 */
887#define SICR_ENET_MASK ((uint)0x0000ff00)
888#define SICR_ENET_CLKRT ((uint)0x00003E00)
889#endif /* CONFIG_LWMON */
890
891/*** NX823 ***********************************************/
892
893#if defined(CONFIG_NX823)
894/* Bits in parallel I/O port registers that have to be set/cleared
895 * to configure the pins for SCC1 use.
896 */
897#define PROFF_ENET PROFF_SCC2
898#define CPM_CR_ENET CPM_CR_CH_SCC2
899#define SCC_ENET 1
wdenk7c7a23b2002-12-07 00:20:59 +0000900#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
901#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
902#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
903#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
wdenkfe8c2802002-11-03 00:38:21 +0000904
wdenk7c7a23b2002-12-07 00:20:59 +0000905#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
wdenkfe8c2802002-11-03 00:38:21 +0000906
wdenk7c7a23b2002-12-07 00:20:59 +0000907#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
908#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
wdenkfe8c2802002-11-03 00:38:21 +0000909
910/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
911 * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
912 */
wdenk7c7a23b2002-12-07 00:20:59 +0000913#define SICR_ENET_MASK ((uint)0x0000ff00)
914#define SICR_ENET_CLKRT ((uint)0x00002f00)
wdenkfe8c2802002-11-03 00:38:21 +0000915
916#endif /* CONFIG_NX823 */
917
918/*** MBX ************************************************************/
919
920#ifdef CONFIG_MBX
921/* Bits in parallel I/O port registers that have to be set/cleared
922 * to configure the pins for SCC1 use. The TCLK and RCLK seem unique
923 * to the MBX860 board. Any two of the four available clocks could be
924 * used, and the MPC860 cookbook manual has an example using different
925 * clock pins.
926 */
927#define PROFF_ENET PROFF_SCC1
928#define CPM_CR_ENET CPM_CR_CH_SCC1
929#define SCC_ENET 0
930#define PA_ENET_RXD ((ushort)0x0001)
931#define PA_ENET_TXD ((ushort)0x0002)
932#define PA_ENET_TCLK ((ushort)0x0200)
933#define PA_ENET_RCLK ((ushort)0x0800)
934#define PC_ENET_TENA ((ushort)0x0001)
935#define PC_ENET_CLSN ((ushort)0x0010)
936#define PC_ENET_RENA ((ushort)0x0020)
937
938/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
939 * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
940 */
941#define SICR_ENET_MASK ((uint)0x000000ff)
942#define SICR_ENET_CLKRT ((uint)0x0000003d)
943#endif /* CONFIG_MBX */
944
Heiko Schocherd0449542009-03-12 07:37:28 +0100945/*** KM8XX *********************************************************/
Heiko Schocher381e4e62008-01-11 01:12:06 +0100946
Heiko Schocherd0449542009-03-12 07:37:28 +0100947/* The KM8XX Service Module uses SCC3 for Ethernet */
Heiko Schocher381e4e62008-01-11 01:12:06 +0100948
Heiko Schocherd0449542009-03-12 07:37:28 +0100949#ifdef CONFIG_KM8XX
Heiko Schocher381e4e62008-01-11 01:12:06 +0100950#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
951#define CPM_CR_ENET CPM_CR_CH_SCC3
952#define SCC_ENET 2
953#define PA_ENET_RXD ((ushort)0x0010) /* PA 11 */
954#define PA_ENET_TXD ((ushort)0x0020) /* PA 10 */
955#define PA_ENET_RCLK ((ushort)0x1000) /* PA 3 CLK 5 */
956#define PA_ENET_TCLK ((ushort)0x2000) /* PA 2 CLK 6 */
957
958#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
959
960#define PC_ENET_RENA ((ushort)0x0200) /* PC 6 */
961#define PC_ENET_CLSN ((ushort)0x0100) /* PC 7 */
962
963/* Control bits in the SICR to route TCLK (CLK6) and RCLK (CLK5) to
964 * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
965 */
966#define SICR_ENET_MASK ((uint)0x00FF0000)
967#define SICR_ENET_CLKRT ((uint)0x00250000)
Heiko Schocherd0449542009-03-12 07:37:28 +0100968#endif /* CONFIG_KM8XX */
Heiko Schocher381e4e62008-01-11 01:12:06 +0100969
970
wdenkfe8c2802002-11-03 00:38:21 +0000971/*** MHPC ********************************************************/
972
973#if defined(CONFIG_MHPC)
974/* This ENET stuff is for the MHPC with ethernet on SCC2.
975 * Note TENA is on Port B.
976 */
977#define PROFF_ENET PROFF_SCC2
978#define CPM_CR_ENET CPM_CR_CH_SCC2
979#define SCC_ENET 1
980#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
981#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
982#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
983#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
984#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
985#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
986#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
987
988#define SICR_ENET_MASK ((uint)0x0000ff00)
989#define SICR_ENET_CLKRT ((uint)0x00002e00) /* RCLK-CLK2, TCLK-CLK3 */
990#endif /* CONFIG_MHPC */
991
wdenk608c9142003-01-13 23:54:46 +0000992/*** NETVIA *******************************************************/
993
wdenkdc7c9a12003-03-26 06:55:25 +0000994/* SinoVee Microsystems SC8xx series FEL8xx-AT,SC823,SC850,SC855T,SC860T */
995#if ( defined CONFIG_SVM_SC8xx )
996# ifndef CONFIG_FEC_ENET
997
998#define PROFF_ENET PROFF_SCC2
999#define CPM_CR_ENET CPM_CR_CH_SCC2
1000#define SCC_ENET 1
1001
1002 /* Bits in parallel I/O port registers that have to be set/cleared
1003 * * * * to configure the pins for SCC2 use.
1004 * * * */
1005#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
1006#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
1007#define PA_ENET_RCLK ((ushort)0x0400) /* PA 5 */
1008#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
1009
1010#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
1011
1012#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
1013#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
1014/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
1015 * * * * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
1016 * * * */
1017#define SICR_ENET_MASK ((uint)0x0000ff00)
1018#define SICR_ENET_CLKRT ((uint)0x00003700)
1019
1020# else /* Use FEC for Fast Ethernet */
1021
1022#undef SCC_ENET
1023#define FEC_ENET
1024
1025#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
1026#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
1027#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
1028#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
1029#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
1030#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
1031#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
1032#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
1033#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
1034#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
1035#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
1036#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
1037#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
1038
1039#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
1040
1041# endif /* CONFIG_FEC_ENET */
1042#endif /* CONFIG_SVM_SC8xx */
wdenk8bde7f72003-06-27 21:31:46 +00001043
1044
wdenk608c9142003-01-13 23:54:46 +00001045#if defined(CONFIG_NETVIA)
1046/* Bits in parallel I/O port registers that have to be set/cleared
1047 * to configure the pins for SCC2 use.
1048 */
1049#define PROFF_ENET PROFF_SCC2
1050#define CPM_CR_ENET CPM_CR_CH_SCC2
1051#define SCC_ENET 1
1052#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
1053#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
1054#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
1055#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
1056
wdenk993cad92003-06-26 22:04:09 +00001057#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1
1058# define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */
1059#elif CONFIG_NETVIA_VERSION >= 2
1060# define PC_ENET_PDN ((ushort)0x0008) /* PC 12 */
1061#endif
1062
wdenk608c9142003-01-13 23:54:46 +00001063#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */
1064
1065#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
1066#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
1067
1068/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
1069 * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
1070 */
1071#define SICR_ENET_MASK ((uint)0x0000ff00)
1072#define SICR_ENET_CLKRT ((uint)0x00002f00)
1073
1074#endif /* CONFIG_NETVIA */
1075
wdenk3bbc8992003-12-07 22:27:15 +00001076/*** QS850/QS823 ***************************************************/
1077
1078#if defined(CONFIG_QS850) || defined(CONFIG_QS823)
1079#undef FEC_ENET /* Don't use FEC for EThernet */
1080
1081#define PROFF_ENET PROFF_SCC2
1082#define CPM_CR_ENET CPM_CR_CH_SCC2
1083#define SCC_ENET 1
1084
1085#define PA_ENET_RXD ((ushort)0x0004) /* RXD on PA13 (Pin D9) */
1086#define PA_ENET_TXD ((ushort)0x0008) /* TXD on PA12 (Pin D7) */
1087#define PC_ENET_RENA ((ushort)0x0080) /* RENA on PC8 (Pin D12) */
1088#define PC_ENET_CLSN ((ushort)0x0040) /* CLSN on PC9 (Pin C12) */
1089#define PA_ENET_TCLK ((ushort)0x0200) /* TCLK on PA6 (Pin D8) */
1090#define PA_ENET_RCLK ((ushort)0x0800) /* RCLK on PA4 (Pin D10) */
1091#define PB_ENET_TENA ((uint)0x00002000) /* TENA on PB18 (Pin D11) */
1092#define PC_ENET_LBK ((ushort)0x0010) /* Loopback control on PC11 (Pin B14) */
1093#define PC_ENET_LI ((ushort)0x0020) /* Link Integrity control PC10 (A15) */
1094#define PC_ENET_SQE ((ushort)0x0100) /* SQE Disable control PC7 (B15) */
1095
1096/* SCC2 TXCLK from CLK2
1097 * SCC2 RXCLK from CLK4
1098 * SCC2 Connected to NMSI */
1099#define SICR_ENET_MASK ((uint)0x00007F00)
1100#define SICR_ENET_CLKRT ((uint)0x00003D00)
1101
1102#endif /* CONFIG_QS850/QS823 */
1103
1104/*** QS860T ***************************************************/
1105
1106#ifdef CONFIG_QS860T
1107#ifdef CONFIG_FEC_ENET
1108#define FEC_ENET /* use FEC for EThernet */
1109#endif /* CONFIG_FEC_ETHERNET */
1110
1111/* This ENET stuff is for GTH 10 Mbit ( SCC ) */
1112#define PROFF_ENET PROFF_SCC1
1113#define CPM_CR_ENET CPM_CR_CH_SCC1
1114#define SCC_ENET 0
1115
1116#define PA_ENET_RXD ((ushort)0x0001) /* PA15 */
1117#define PA_ENET_TXD ((ushort)0x0002) /* PA14 */
1118#define PA_ENET_TCLK ((ushort)0x0800) /* PA4 */
1119#define PA_ENET_RCLK ((ushort)0x0200) /* PA6 */
1120#define PB_ENET_TENA ((uint)0x00001000) /* PB19 */
1121#define PC_ENET_CLSN ((ushort)0x0010) /* PC11 */
1122#define PC_ENET_RENA ((ushort)0x0020) /* PC10 */
1123
1124#define SICR_ENET_MASK ((uint)0x000000ff)
1125/* RCLK PA4 -->CLK4, TCLK PA6 -->CLK2 */
1126#define SICR_ENET_CLKRT ((uint)0x0000003D)
1127
1128#endif /* CONFIG_QS860T */
1129
wdenkfe8c2802002-11-03 00:38:21 +00001130/*** RPXCLASSIC *****************************************************/
1131
1132#ifdef CONFIG_RPXCLASSIC
1133
1134#ifdef CONFIG_FEC_ENET
1135
1136# define FEC_ENET /* use FEC for EThernet */
1137# undef SCC_ENET
1138
1139#else /* ! CONFIG_FEC_ENET */
1140
1141/* Bits in parallel I/O port registers that have to be set/cleared
1142 * to configure the pins for SCC1 use.
1143 */
1144#define PROFF_ENET PROFF_SCC1
1145#define CPM_CR_ENET CPM_CR_CH_SCC1
1146#define SCC_ENET 0
1147#define PA_ENET_RXD ((ushort)0x0001)
1148#define PA_ENET_TXD ((ushort)0x0002)
1149#define PA_ENET_TCLK ((ushort)0x0200)
1150#define PA_ENET_RCLK ((ushort)0x0800)
1151#define PB_ENET_TENA ((uint)0x00001000)
1152#define PC_ENET_CLSN ((ushort)0x0010)
1153#define PC_ENET_RENA ((ushort)0x0020)
1154
1155/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
1156 * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
1157 */
1158#define SICR_ENET_MASK ((uint)0x000000ff)
1159#define SICR_ENET_CLKRT ((uint)0x0000003d)
1160
1161#endif /* CONFIG_FEC_ENET */
1162
1163#endif /* CONFIG_RPXCLASSIC */
1164
1165/*** RPXLITE ********************************************************/
1166
1167#ifdef CONFIG_RPXLITE
1168/* This ENET stuff is for the MPC850 with ethernet on SCC2. Some of
1169 * this may be unique to the RPX-Lite configuration.
1170 * Note TENA is on Port B.
1171 */
1172#define PROFF_ENET PROFF_SCC2
1173#define CPM_CR_ENET CPM_CR_CH_SCC2
1174#define SCC_ENET 1
1175#define PA_ENET_RXD ((ushort)0x0004)
1176#define PA_ENET_TXD ((ushort)0x0008)
1177#define PA_ENET_TCLK ((ushort)0x0200)
1178#define PA_ENET_RCLK ((ushort)0x0800)
wdenk73a8b272003-06-05 19:27:42 +00001179#if defined(CONFIG_RMU)
1180#define PC_ENET_TENA ((uint)0x00000002) /* PC14 */
1181#else
wdenkfe8c2802002-11-03 00:38:21 +00001182#define PB_ENET_TENA ((uint)0x00002000)
wdenk73a8b272003-06-05 19:27:42 +00001183#endif
wdenkfe8c2802002-11-03 00:38:21 +00001184#define PC_ENET_CLSN ((ushort)0x0040)
1185#define PC_ENET_RENA ((ushort)0x0080)
1186
1187#define SICR_ENET_MASK ((uint)0x0000ff00)
1188#define SICR_ENET_CLKRT ((uint)0x00003d00)
1189#endif /* CONFIG_RPXLITE */
1190
1191/*** SM850 *********************************************************/
1192
1193/* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */
1194
1195#ifdef CONFIG_SM850
1196#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
1197#define CPM_CR_ENET CPM_CR_CH_SCC3
1198#define SCC_ENET 2
1199#define PB_ENET_RXD ((uint)0x00000004) /* PB 29 */
1200#define PB_ENET_TXD ((uint)0x00000002) /* PB 30 */
1201#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
1202#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
1203
1204#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
1205#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
1206
1207#define PC_ENET_RENA ((ushort)0x0800) /* PC 4 */
1208#define PC_ENET_CLSN ((ushort)0x0400) /* PC 5 */
1209
1210/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
1211 * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
1212 */
1213#define SICR_ENET_MASK ((uint)0x00FF0000)
1214#define SICR_ENET_CLKRT ((uint)0x00260000)
1215#endif /* CONFIG_SM850 */
1216
1217/*** SPD823TS ******************************************************/
1218
1219#ifdef CONFIG_SPD823TS
1220/* Bits in parallel I/O port registers that have to be set/cleared
1221 * to configure the pins for SCC2 use.
1222 */
1223#define PROFF_ENET PROFF_SCC2 /* Ethernet on SCC2 */
1224#define CPM_CR_ENET CPM_CR_CH_SCC2
1225#define SCC_ENET 1
1226#define PA_ENET_MDC ((ushort)0x0001) /* PA 15 !!! */
1227#define PA_ENET_MDIO ((ushort)0x0002) /* PA 14 !!! */
1228#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
1229#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
1230#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
1231#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
1232
1233#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
1234
1235#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
1236#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
1237#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 !!! */
1238
1239/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
1240 * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
1241 */
1242#define SICR_ENET_MASK ((uint)0x0000ff00)
1243#define SICR_ENET_CLKRT ((uint)0x00002E00)
1244#endif /* CONFIG_SPD823TS */
1245
1246/*** SXNI855T ******************************************************/
1247
1248#if defined(CONFIG_SXNI855T)
1249
1250#ifdef CONFIG_FEC_ENET
1251#define FEC_ENET /* use FEC for Ethernet */
1252#endif /* CONFIG_FEC_ETHERNET */
1253
1254#endif /* CONFIG_SXNI855T */
1255
Wolfgang Denk1b0757e2012-10-24 02:36:15 +00001256/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/
wdenkfe8c2802002-11-03 00:38:21 +00001257
1258#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
wdenk71f95112003-06-15 22:40:42 +00001259 defined(CONFIG_R360MPI) || defined(CONFIG_RBC823) || \
Wolfgang Denk1b0757e2012-10-24 02:36:15 +00001260 defined(CONFIG_RRVISION)|| defined(CONFIG_TQM823L) || \
1261 defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \
1262 defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D) || \
1263 defined(CONFIG_RRVISION)|| defined(CONFIG_VIRTLAB2)
Markus Klotzbuecher090eb732006-07-12 15:26:01 +02001264
wdenkfe8c2802002-11-03 00:38:21 +00001265/* Bits in parallel I/O port registers that have to be set/cleared
1266 * to configure the pins for SCC2 use.
1267 */
1268#define PROFF_ENET PROFF_SCC2
1269#define CPM_CR_ENET CPM_CR_CH_SCC2
Wolfgang Denk2b4f7782008-01-15 17:21:28 +01001270#if (!defined(CONFIG_TK885D)) /* TK885D does not use SCC Ethernet */
wdenkfe8c2802002-11-03 00:38:21 +00001271#define SCC_ENET 1
Wolfgang Denk2b4f7782008-01-15 17:21:28 +01001272#endif
wdenkfe8c2802002-11-03 00:38:21 +00001273#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
1274#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
1275#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
1276#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
1277
1278#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
1279
1280#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
1281#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
1282#if defined(CONFIG_R360MPI)
1283#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
1284#endif /* CONFIG_R360MPI */
1285
1286/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
1287 * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
1288 */
1289#define SICR_ENET_MASK ((uint)0x0000ff00)
1290#define SICR_ENET_CLKRT ((uint)0x00002600)
Markus Klotzbuecher090eb732006-07-12 15:26:01 +02001291
1292# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
1293#define FEC_ENET
1294# endif /* CONFIG_FEC_ENET */
1295
wdenk71f95112003-06-15 22:40:42 +00001296#endif /* CONFIG_MVS v1, CONFIG_TQM823L/M, CONFIG_TQM850L/M, etc. */
wdenkfe8c2802002-11-03 00:38:21 +00001297
wdenkd4ca31c2004-01-02 14:00:00 +00001298/*** TQM855L/M, TQM860L/M, TQM862L/M, TQM866L/M *********************/
wdenkfe8c2802002-11-03 00:38:21 +00001299
wdenk71f95112003-06-15 22:40:42 +00001300#if defined(CONFIG_TQM855L) || defined(CONFIG_TQM855M) || \
1301 defined(CONFIG_TQM860L) || defined(CONFIG_TQM860M) || \
wdenkd4ca31c2004-01-02 14:00:00 +00001302 defined(CONFIG_TQM862L) || defined(CONFIG_TQM862M) || \
1303 defined(CONFIG_TQM866L) || defined(CONFIG_TQM866M)
wdenkfe8c2802002-11-03 00:38:21 +00001304
1305# ifdef CONFIG_SCC1_ENET /* use SCC for 10Mbps Ethernet */
1306
1307/* Bits in parallel I/O port registers that have to be set/cleared
1308 * to configure the pins for SCC1 use.
1309 */
1310#define PROFF_ENET PROFF_SCC1
1311#define CPM_CR_ENET CPM_CR_CH_SCC1
1312#define SCC_ENET 0
1313#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
1314#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
1315#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
1316#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
1317
1318#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
1319#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
1320#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
1321
1322/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
1323 * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
1324 */
1325#define SICR_ENET_MASK ((uint)0x000000ff)
1326#define SICR_ENET_CLKRT ((uint)0x00000026)
1327
1328# endif /* CONFIG_SCC1_ENET */
1329
1330# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
1331
1332#define FEC_ENET
1333
1334#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
1335#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
1336#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
1337#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
1338#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
1339#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
1340#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
1341#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
1342#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
1343#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
1344#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
1345#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
1346#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
1347
1348#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
1349
1350# endif /* CONFIG_FEC_ENET */
wdenk71f95112003-06-15 22:40:42 +00001351#endif /* CONFIG_TQM855L/M, TQM860L/M, TQM862L/M */
wdenkfe8c2802002-11-03 00:38:21 +00001352
wdenk608c9142003-01-13 23:54:46 +00001353/*** V37 **********************************************************/
1354
1355#ifdef CONFIG_V37
1356/* This ENET stuff is for the MPC823 with ethernet on SCC2. Some of
1357 * this may be unique to the Marel V37 configuration.
1358 * Note TENA is on Port B.
wdenkfe8c2802002-11-03 00:38:21 +00001359 */
1360#define PROFF_ENET PROFF_SCC2
1361#define CPM_CR_ENET CPM_CR_CH_SCC2
1362#define SCC_ENET 1
wdenk608c9142003-01-13 23:54:46 +00001363#define PA_ENET_RXD ((ushort)0x0004)
1364#define PA_ENET_TXD ((ushort)0x0008)
1365#define PA_ENET_TCLK ((ushort)0x0400)
1366#define PA_ENET_RCLK ((ushort)0x0200)
1367#define PB_ENET_TENA ((uint)0x00002000)
1368#define PC_ENET_CLSN ((ushort)0x0040)
1369#define PC_ENET_RENA ((ushort)0x0080)
wdenkfe8c2802002-11-03 00:38:21 +00001370
wdenkfe8c2802002-11-03 00:38:21 +00001371#define SICR_ENET_MASK ((uint)0x0000ff00)
wdenk608c9142003-01-13 23:54:46 +00001372#define SICR_ENET_CLKRT ((uint)0x00002e00)
1373#endif /* CONFIG_V37 */
wdenkfe8c2802002-11-03 00:38:21 +00001374
wdenk3bbc8992003-12-07 22:27:15 +00001375
wdenkfe8c2802002-11-03 00:38:21 +00001376/*********************************************************************/
1377
1378/* SCC Event register as used by Ethernet.
1379*/
1380#define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */
1381#define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */
1382#define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */
1383#define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */
1384#define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */
1385#define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */
1386
1387/* SCC Mode Register (PSMR) as used by Ethernet.
1388*/
1389#define SCC_PSMR_HBC ((ushort)0x8000) /* Enable heartbeat */
1390#define SCC_PSMR_FC ((ushort)0x4000) /* Force collision */
1391#define SCC_PSMR_RSH ((ushort)0x2000) /* Receive short frames */
1392#define SCC_PSMR_IAM ((ushort)0x1000) /* Check individual hash */
1393#define SCC_PSMR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */
1394#define SCC_PSMR_PRO ((ushort)0x0200) /* Promiscuous mode */
1395#define SCC_PSMR_BRO ((ushort)0x0100) /* Catch broadcast pkts */
1396#define SCC_PSMR_SBT ((ushort)0x0080) /* Special backoff timer */
1397#define SCC_PSMR_LPB ((ushort)0x0040) /* Set Loopback mode */
1398#define SCC_PSMR_SIP ((ushort)0x0020) /* Sample Input Pins */
1399#define SCC_PSMR_LCW ((ushort)0x0010) /* Late collision window */
1400#define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */
1401#define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */
1402
1403/* Buffer descriptor control/status used by Ethernet receive.
1404*/
1405#define BD_ENET_RX_EMPTY ((ushort)0x8000)
1406#define BD_ENET_RX_WRAP ((ushort)0x2000)
1407#define BD_ENET_RX_INTR ((ushort)0x1000)
1408#define BD_ENET_RX_LAST ((ushort)0x0800)
1409#define BD_ENET_RX_FIRST ((ushort)0x0400)
1410#define BD_ENET_RX_MISS ((ushort)0x0100)
1411#define BD_ENET_RX_LG ((ushort)0x0020)
1412#define BD_ENET_RX_NO ((ushort)0x0010)
1413#define BD_ENET_RX_SH ((ushort)0x0008)
1414#define BD_ENET_RX_CR ((ushort)0x0004)
1415#define BD_ENET_RX_OV ((ushort)0x0002)
1416#define BD_ENET_RX_CL ((ushort)0x0001)
1417#define BD_ENET_RX_STATS ((ushort)0x013f) /* All status bits */
1418
1419/* Buffer descriptor control/status used by Ethernet transmit.
1420*/
1421#define BD_ENET_TX_READY ((ushort)0x8000)
1422#define BD_ENET_TX_PAD ((ushort)0x4000)
1423#define BD_ENET_TX_WRAP ((ushort)0x2000)
1424#define BD_ENET_TX_INTR ((ushort)0x1000)
1425#define BD_ENET_TX_LAST ((ushort)0x0800)
1426#define BD_ENET_TX_TC ((ushort)0x0400)
1427#define BD_ENET_TX_DEF ((ushort)0x0200)
1428#define BD_ENET_TX_HB ((ushort)0x0100)
1429#define BD_ENET_TX_LC ((ushort)0x0080)
1430#define BD_ENET_TX_RL ((ushort)0x0040)
1431#define BD_ENET_TX_RCMASK ((ushort)0x003c)
1432#define BD_ENET_TX_UN ((ushort)0x0002)
1433#define BD_ENET_TX_CSL ((ushort)0x0001)
1434#define BD_ENET_TX_STATS ((ushort)0x03ff) /* All status bits */
1435
1436/* SCC as UART
1437*/
1438typedef struct scc_uart {
1439 sccp_t scc_genscc;
1440 uint scc_res1; /* Reserved */
1441 uint scc_res2; /* Reserved */
1442 ushort scc_maxidl; /* Maximum idle chars */
1443 ushort scc_idlc; /* temp idle counter */
1444 ushort scc_brkcr; /* Break count register */
1445 ushort scc_parec; /* receive parity error counter */
1446 ushort scc_frmec; /* receive framing error counter */
1447 ushort scc_nosec; /* receive noise counter */
1448 ushort scc_brkec; /* receive break condition counter */
1449 ushort scc_brkln; /* last received break length */
1450 ushort scc_uaddr1; /* UART address character 1 */
1451 ushort scc_uaddr2; /* UART address character 2 */
1452 ushort scc_rtemp; /* Temp storage */
1453 ushort scc_toseq; /* Transmit out of sequence char */
1454 ushort scc_char1; /* control character 1 */
1455 ushort scc_char2; /* control character 2 */
1456 ushort scc_char3; /* control character 3 */
1457 ushort scc_char4; /* control character 4 */
1458 ushort scc_char5; /* control character 5 */
1459 ushort scc_char6; /* control character 6 */
1460 ushort scc_char7; /* control character 7 */
1461 ushort scc_char8; /* control character 8 */
1462 ushort scc_rccm; /* receive control character mask */
1463 ushort scc_rccr; /* receive control character register */
1464 ushort scc_rlbc; /* receive last break character */
1465} scc_uart_t;
1466
1467/* SCC Event and Mask registers when it is used as a UART.
1468*/
1469#define UART_SCCM_GLR ((ushort)0x1000)
1470#define UART_SCCM_GLT ((ushort)0x0800)
1471#define UART_SCCM_AB ((ushort)0x0200)
1472#define UART_SCCM_IDL ((ushort)0x0100)
1473#define UART_SCCM_GRA ((ushort)0x0080)
1474#define UART_SCCM_BRKE ((ushort)0x0040)
1475#define UART_SCCM_BRKS ((ushort)0x0020)
1476#define UART_SCCM_CCR ((ushort)0x0008)
1477#define UART_SCCM_BSY ((ushort)0x0004)
1478#define UART_SCCM_TX ((ushort)0x0002)
1479#define UART_SCCM_RX ((ushort)0x0001)
1480
1481/* The SCC PSMR when used as a UART.
1482*/
1483#define SCU_PSMR_FLC ((ushort)0x8000)
1484#define SCU_PSMR_SL ((ushort)0x4000)
1485#define SCU_PSMR_CL ((ushort)0x3000)
1486#define SCU_PSMR_UM ((ushort)0x0c00)
1487#define SCU_PSMR_FRZ ((ushort)0x0200)
1488#define SCU_PSMR_RZS ((ushort)0x0100)
1489#define SCU_PSMR_SYN ((ushort)0x0080)
1490#define SCU_PSMR_DRT ((ushort)0x0040)
1491#define SCU_PSMR_PEN ((ushort)0x0010)
1492#define SCU_PSMR_RPM ((ushort)0x000c)
1493#define SCU_PSMR_REVP ((ushort)0x0008)
1494#define SCU_PSMR_TPM ((ushort)0x0003)
1495#define SCU_PSMR_TEVP ((ushort)0x0003)
1496
1497/* CPM Transparent mode SCC.
1498 */
1499typedef struct scc_trans {
1500 sccp_t st_genscc;
1501 uint st_cpres; /* Preset CRC */
1502 uint st_cmask; /* Constant mask for CRC */
1503} scc_trans_t;
1504
1505#define BD_SCC_TX_LAST ((ushort)0x0800)
1506
1507/* IIC parameter RAM.
1508*/
1509typedef struct iic {
1510 ushort iic_rbase; /* Rx Buffer descriptor base address */
1511 ushort iic_tbase; /* Tx Buffer descriptor base address */
1512 u_char iic_rfcr; /* Rx function code */
1513 u_char iic_tfcr; /* Tx function code */
1514 ushort iic_mrblr; /* Max receive buffer length */
1515 uint iic_rstate; /* Internal */
1516 uint iic_rdp; /* Internal */
1517 ushort iic_rbptr; /* Internal */
1518 ushort iic_rbc; /* Internal */
1519 uint iic_rxtmp; /* Internal */
1520 uint iic_tstate; /* Internal */
1521 uint iic_tdp; /* Internal */
1522 ushort iic_tbptr; /* Internal */
1523 ushort iic_tbc; /* Internal */
1524 uint iic_txtmp; /* Internal */
1525 uint iic_res; /* reserved */
1526 ushort iic_rpbase; /* Relocation pointer */
1527 ushort iic_res2; /* reserved */
1528} iic_t;
1529
1530/* SPI parameter RAM.
1531*/
1532typedef struct spi {
1533 ushort spi_rbase; /* Rx Buffer descriptor base address */
1534 ushort spi_tbase; /* Tx Buffer descriptor base address */
1535 u_char spi_rfcr; /* Rx function code */
1536 u_char spi_tfcr; /* Tx function code */
1537 ushort spi_mrblr; /* Max receive buffer length */
1538 uint spi_rstate; /* Internal */
1539 uint spi_rdp; /* Internal */
1540 ushort spi_rbptr; /* Internal */
1541 ushort spi_rbc; /* Internal */
1542 uint spi_rxtmp; /* Internal */
1543 uint spi_tstate; /* Internal */
1544 uint spi_tdp; /* Internal */
1545 ushort spi_tbptr; /* Internal */
1546 ushort spi_tbc; /* Internal */
1547 uint spi_txtmp; /* Internal */
1548 uint spi_res;
1549 ushort spi_rpbase; /* Relocation pointer */
1550 ushort spi_res2;
1551} spi_t;
1552
1553/* SPI Mode register.
1554*/
1555#define SPMODE_LOOP ((ushort)0x4000) /* Loopback */
1556#define SPMODE_CI ((ushort)0x2000) /* Clock Invert */
1557#define SPMODE_CP ((ushort)0x1000) /* Clock Phase */
1558#define SPMODE_DIV16 ((ushort)0x0800) /* BRG/16 mode */
1559#define SPMODE_REV ((ushort)0x0400) /* Reversed Data */
1560#define SPMODE_MSTR ((ushort)0x0200) /* SPI Master */
1561#define SPMODE_EN ((ushort)0x0100) /* Enable */
1562#define SPMODE_LENMSK ((ushort)0x00f0) /* character length */
1563#define SPMODE_PMMSK ((ushort)0x000f) /* prescale modulus */
1564
1565#define SPMODE_LEN(x) ((((x)-1)&0xF)<<4)
1566#define SPMODE_PM(x) ((x) &0xF)
1567
1568/* HDLC parameter RAM.
1569*/
1570
1571typedef struct hdlc_pram_s {
1572 /*
1573 * SCC parameter RAM
1574 */
1575 ushort rbase; /* Rx Buffer descriptor base address */
1576 ushort tbase; /* Tx Buffer descriptor base address */
1577 uchar rfcr; /* Rx function code */
1578 uchar tfcr; /* Tx function code */
1579 ushort mrblr; /* Rx buffer length */
1580 ulong rstate; /* Rx internal state */
1581 ulong rptr; /* Rx internal data pointer */
1582 ushort rbptr; /* rb BD Pointer */
1583 ushort rcount; /* Rx internal byte count */
1584 ulong rtemp; /* Rx temp */
1585 ulong tstate; /* Tx internal state */
1586 ulong tptr; /* Tx internal data pointer */
1587 ushort tbptr; /* Tx BD pointer */
1588 ushort tcount; /* Tx byte count */
1589 ulong ttemp; /* Tx temp */
1590 ulong rcrc; /* temp receive CRC */
1591 ulong tcrc; /* temp transmit CRC */
1592 /*
1593 * HDLC specific parameter RAM
1594 */
1595 uchar res[4]; /* reserved */
1596 ulong c_mask; /* CRC constant */
1597 ulong c_pres; /* CRC preset */
1598 ushort disfc; /* discarded frame counter */
1599 ushort crcec; /* CRC error counter */
1600 ushort abtsc; /* abort sequence counter */
1601 ushort nmarc; /* nonmatching address rx cnt */
1602 ushort retrc; /* frame retransmission cnt */
1603 ushort mflr; /* maximum frame length reg */
1604 ushort max_cnt; /* maximum length counter */
1605 ushort rfthr; /* received frames threshold */
1606 ushort rfcnt; /* received frames count */
1607 ushort hmask; /* user defined frm addr mask */
1608 ushort haddr1; /* user defined frm address 1 */
1609 ushort haddr2; /* user defined frm address 2 */
1610 ushort haddr3; /* user defined frm address 3 */
1611 ushort haddr4; /* user defined frm address 4 */
1612 ushort tmp; /* temp */
1613 ushort tmp_mb; /* temp */
1614} hdlc_pram_t;
1615
1616/* CPM interrupts. There are nearly 32 interrupts generated by CPM
1617 * channels or devices. All of these are presented to the PPC core
1618 * as a single interrupt. The CPM interrupt handler dispatches its
1619 * own handlers, in a similar fashion to the PPC core handler. We
1620 * use the table as defined in the manuals (i.e. no special high
1621 * priority and SCC1 == SCCa, etc...).
1622 */
1623#define CPMVEC_NR 32
wdenk7c7a23b2002-12-07 00:20:59 +00001624#define CPMVEC_OFFSET 0x00010000
1625#define CPMVEC_PIO_PC15 ((ushort)0x1f | CPMVEC_OFFSET)
1626#define CPMVEC_SCC1 ((ushort)0x1e | CPMVEC_OFFSET)
1627#define CPMVEC_SCC2 ((ushort)0x1d | CPMVEC_OFFSET)
1628#define CPMVEC_SCC3 ((ushort)0x1c | CPMVEC_OFFSET)
1629#define CPMVEC_SCC4 ((ushort)0x1b | CPMVEC_OFFSET)
1630#define CPMVEC_PIO_PC14 ((ushort)0x1a | CPMVEC_OFFSET)
1631#define CPMVEC_TIMER1 ((ushort)0x19 | CPMVEC_OFFSET)
1632#define CPMVEC_PIO_PC13 ((ushort)0x18 | CPMVEC_OFFSET)
1633#define CPMVEC_PIO_PC12 ((ushort)0x17 | CPMVEC_OFFSET)
1634#define CPMVEC_SDMA_CB_ERR ((ushort)0x16 | CPMVEC_OFFSET)
1635#define CPMVEC_IDMA1 ((ushort)0x15 | CPMVEC_OFFSET)
1636#define CPMVEC_IDMA2 ((ushort)0x14 | CPMVEC_OFFSET)
1637#define CPMVEC_TIMER2 ((ushort)0x12 | CPMVEC_OFFSET)
1638#define CPMVEC_RISCTIMER ((ushort)0x11 | CPMVEC_OFFSET)
1639#define CPMVEC_I2C ((ushort)0x10 | CPMVEC_OFFSET)
1640#define CPMVEC_PIO_PC11 ((ushort)0x0f | CPMVEC_OFFSET)
1641#define CPMVEC_PIO_PC10 ((ushort)0x0e | CPMVEC_OFFSET)
1642#define CPMVEC_TIMER3 ((ushort)0x0c | CPMVEC_OFFSET)
1643#define CPMVEC_PIO_PC9 ((ushort)0x0b | CPMVEC_OFFSET)
1644#define CPMVEC_PIO_PC8 ((ushort)0x0a | CPMVEC_OFFSET)
1645#define CPMVEC_PIO_PC7 ((ushort)0x09 | CPMVEC_OFFSET)
1646#define CPMVEC_TIMER4 ((ushort)0x07 | CPMVEC_OFFSET)
1647#define CPMVEC_PIO_PC6 ((ushort)0x06 | CPMVEC_OFFSET)
1648#define CPMVEC_SPI ((ushort)0x05 | CPMVEC_OFFSET)
1649#define CPMVEC_SMC1 ((ushort)0x04 | CPMVEC_OFFSET)
1650#define CPMVEC_SMC2 ((ushort)0x03 | CPMVEC_OFFSET)
1651#define CPMVEC_PIO_PC5 ((ushort)0x02 | CPMVEC_OFFSET)
1652#define CPMVEC_PIO_PC4 ((ushort)0x01 | CPMVEC_OFFSET)
1653#define CPMVEC_ERROR ((ushort)0x00 | CPMVEC_OFFSET)
wdenkfe8c2802002-11-03 00:38:21 +00001654
1655extern void irq_install_handler(int vec, void (*handler)(void *), void *dev_id);
1656
1657/* CPM interrupt configuration vector.
1658*/
1659#define CICR_SCD_SCC4 ((uint)0x00c00000) /* SCC4 @ SCCd */
1660#define CICR_SCC_SCC3 ((uint)0x00200000) /* SCC3 @ SCCc */
1661#define CICR_SCB_SCC2 ((uint)0x00040000) /* SCC2 @ SCCb */
1662#define CICR_SCA_SCC1 ((uint)0x00000000) /* SCC1 @ SCCa */
1663#define CICR_IRL_MASK ((uint)0x0000e000) /* Core interrrupt */
1664#define CICR_HP_MASK ((uint)0x00001f00) /* Hi-pri int. */
1665#define CICR_IEN ((uint)0x00000080) /* Int. enable */
1666#define CICR_SPS ((uint)0x00000001) /* SCC Spread */
1667#endif /* __CPM_8XX__ */