blob: ef5ca6444220336398588735482ca1b2360fadc6 [file] [log] [blame]
Chen-Yu Tsaib5fe5232020-01-12 23:36:13 +08001// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2// Copyright (C) 2016 ARM Ltd.
3// Copyright (C) 2018 Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens76d69eb2018-06-09 18:34:46 +02004
5/dts-v1/;
6#include "sun50i-h5.dtsi"
7
8#include <dt-bindings/gpio/gpio.h>
9#include <dt-bindings/input/input.h>
10#include <dt-bindings/pinctrl/sun4i-a10.h>
11
12/ {
13 model = "Xunlong Orange Pi Zero Plus";
14 compatible = "xunlong,orangepi-zero-plus", "allwinner,sun50i-h5";
15
16 reg_vcc3v3: vcc3v3 {
17 compatible = "regulator-fixed";
18 regulator-name = "vcc3v3";
19 regulator-min-microvolt = <3300000>;
20 regulator-max-microvolt = <3300000>;
21 };
22
23 aliases {
24 ethernet0 = &emac;
25 ethernet1 = &rtl8189ftv;
26 serial0 = &uart0;
27 };
28
29 chosen {
30 stdout-path = "serial0:115200n8";
31 };
32
33 leds {
34 compatible = "gpio-leds";
35
36 pwr {
37 label = "orangepi:green:pwr";
38 gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
39 default-state = "on";
40 };
41
42 status {
43 label = "orangepi:red:status";
44 gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
45 };
46 };
47
48 reg_gmac_3v3: gmac-3v3 {
49 compatible = "regulator-fixed";
50 regulator-name = "gmac-3v3";
51 regulator-min-microvolt = <3300000>;
52 regulator-max-microvolt = <3300000>;
53 startup-delay-us = <100000>;
54 enable-active-high;
55 gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
56 };
57};
58
59&ehci0 {
60 status = "okay";
61};
62
63&ehci1 {
64 status = "okay";
65};
66
67&emac {
68 pinctrl-names = "default";
69 pinctrl-0 = <&emac_rgmii_pins>;
70 phy-supply = <&reg_gmac_3v3>;
71 phy-handle = <&ext_rgmii_phy>;
72 phy-mode = "rgmii";
73 status = "okay";
74};
75
76&external_mdio {
77 ext_rgmii_phy: ethernet-phy@1 {
78 compatible = "ethernet-phy-ieee802.3-c22";
79 reg = <1>;
80 };
81};
82
83&mmc0 {
84 vmmc-supply = <&reg_vcc3v3>;
85 bus-width = <4>;
86 cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
87 status = "okay";
88};
89
90&mmc1 {
91 vmmc-supply = <&reg_vcc3v3>;
92 bus-width = <4>;
93 non-removable;
94 status = "okay";
95
96 /*
97 * Explicitly define the sdio device, so that we can add an ethernet
98 * alias for it (which e.g. makes u-boot set a mac-address).
99 */
100 rtl8189ftv: sdio_wifi@1 {
101 reg = <1>;
102 };
103};
104
Hauke Mehrtens76d69eb2018-06-09 18:34:46 +0200105&spi0 {
106 status = "okay";
107
108 flash@0 {
109 #address-cells = <1>;
110 #size-cells = <1>;
111 compatible = "mxicy,mx25l1606e", "winbond,w25q128";
112 reg = <0>;
113 spi-max-frequency = <40000000>;
114 };
115};
Hauke Mehrtens76d69eb2018-06-09 18:34:46 +0200116
117&ohci0 {
118 status = "okay";
119};
120
121&ohci1 {
122 status = "okay";
123};
124
125&uart0 {
126 pinctrl-names = "default";
Chen-Yu Tsaib5fe5232020-01-12 23:36:13 +0800127 pinctrl-0 = <&uart0_pa_pins>;
Hauke Mehrtens76d69eb2018-06-09 18:34:46 +0200128 status = "okay";
129};
130
131&usb_otg {
132 dr_mode = "peripheral";
133 status = "okay";
134};
135
136&usbphy {
137 /* USB Type-A ports' VBUS is always on */
138 usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
139 status = "okay";
140};