blob: abbb92a71e9214f65ad10c92e51493238036baec [file] [log] [blame]
Kim Phillips1c274c42007-07-25 19:25:33 -05001/*
2 * Copyright (C) 2007 Freescale Semiconductor, Inc.
3 *
4 * This program is free software; you can redistribute it and/or modify it
5 * under the terms of the GNU General Public License version 2 as published
6 * by the Free Software Foundation.
7 */
8
9#ifndef __CONFIG_H
10#define __CONFIG_H
11
Kim Phillips1c274c42007-07-25 19:25:33 -050012/*
13 * High Level Configuration Options
14 */
15#define CONFIG_E300 1 /* E300 family */
16#define CONFIG_QE 1 /* Has QE */
Peter Tyser0f898602009-05-22 17:23:24 -050017#define CONFIG_MPC83xx 1 /* MPC83xx family */
Peter Tyser2c7920a2009-05-22 17:23:25 -050018#define CONFIG_MPC832x 1 /* MPC832x CPU specific */
Kim Phillips1c274c42007-07-25 19:25:33 -050019
Wolfgang Denk2ae18242010-10-06 09:05:45 +020020#define CONFIG_SYS_TEXT_BASE 0xFE000000
21
Kim Phillips1c274c42007-07-25 19:25:33 -050022#define CONFIG_PCI 1
Kim Phillips1c274c42007-07-25 19:25:33 -050023
24/*
25 * System Clock Setup
26 */
27#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
28
29#ifndef CONFIG_SYS_CLK_FREQ
30#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
31#endif
32
33/*
34 * Hardware Reset Configuration Word
35 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020036#define CONFIG_SYS_HRCW_LOW (\
Kim Phillips1c274c42007-07-25 19:25:33 -050037 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
38 HRCWL_DDR_TO_SCB_CLK_2X1 |\
39 HRCWL_VCO_1X2 |\
40 HRCWL_CSB_TO_CLKIN_2X1 |\
41 HRCWL_CORE_TO_CSB_2_5X1 |\
42 HRCWL_CE_PLL_VCO_DIV_2 |\
43 HRCWL_CE_PLL_DIV_1X1 |\
44 HRCWL_CE_TO_PLL_1X3)
45
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020046#define CONFIG_SYS_HRCW_HIGH (\
Kim Phillips1c274c42007-07-25 19:25:33 -050047 HRCWH_PCI_HOST |\
48 HRCWH_PCI1_ARBITER_ENABLE |\
49 HRCWH_CORE_ENABLE |\
50 HRCWH_FROM_0X00000100 |\
51 HRCWH_BOOTSEQ_DISABLE |\
52 HRCWH_SW_WATCHDOG_DISABLE |\
53 HRCWH_ROM_LOC_LOCAL_16BIT |\
54 HRCWH_BIG_ENDIAN |\
55 HRCWH_LALE_NORMAL)
56
57/*
58 * System IO Config
59 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020060#define CONFIG_SYS_SICRL 0x00000000
Kim Phillips1c274c42007-07-25 19:25:33 -050061
62#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
63
64/*
65 * IMMR new address
66 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020067#define CONFIG_SYS_IMMR 0xE0000000
Kim Phillips1c274c42007-07-25 19:25:33 -050068
69/*
Michael Barkowski5bbeea82008-03-20 13:15:34 -040070 * System performance
71 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020072#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
73#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
74#define CONFIG_SYS_SPCR_OPT 1 /* (0-1) Optimize transactions between CSB and the SEC and QUICC Engine block */
Michael Barkowski5bbeea82008-03-20 13:15:34 -040075
76/*
Kim Phillips1c274c42007-07-25 19:25:33 -050077 * DDR Setup
78 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020079#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
80#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
81#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
82#define CONFIG_SYS_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */
Kim Phillips1c274c42007-07-25 19:25:33 -050083
84#undef CONFIG_SPD_EEPROM
85#if defined(CONFIG_SPD_EEPROM)
86/* Determine DDR configuration from I2C interface
87 */
88#define SPD_EEPROM_ADDRESS 0x51 /* DDR SODIMM */
89#else
90/* Manually set up DDR parameters
91 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020092#define CONFIG_SYS_DDR_SIZE 64 /* MB */
93#define CONFIG_SYS_DDR_CS0_CONFIG ( CSCONFIG_EN \
Michael Barkowski5bbeea82008-03-20 13:15:34 -040094 | CSCONFIG_ODT_WR_ACS \
Michael Barkowskifc549c82008-03-20 13:15:28 -040095 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_9 )
Michael Barkowski5bbeea82008-03-20 13:15:34 -040096 /* 0x80010101 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020097#define CONFIG_SYS_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
Michael Barkowskifc549c82008-03-20 13:15:28 -040098 | ( 0 << TIMING_CFG0_WRT_SHIFT ) \
99 | ( 0 << TIMING_CFG0_RRT_SHIFT ) \
100 | ( 0 << TIMING_CFG0_WWT_SHIFT ) \
101 | ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
102 | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
103 | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
104 | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
105 /* 0x00220802 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200106#define CONFIG_SYS_DDR_TIMING_1 ( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \
Michael Barkowski5bbeea82008-03-20 13:15:34 -0400107 | ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
108 | ( 2 << TIMING_CFG1_ACTTORW_SHIFT ) \
Michael Barkowskifc549c82008-03-20 13:15:28 -0400109 | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
Michael Barkowski5bbeea82008-03-20 13:15:34 -0400110 | ( 3 << TIMING_CFG1_REFREC_SHIFT ) \
111 | ( 2 << TIMING_CFG1_WRREC_SHIFT ) \
Michael Barkowskifc549c82008-03-20 13:15:28 -0400112 | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
113 | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
Michael Barkowski5bbeea82008-03-20 13:15:34 -0400114 /* 0x26253222 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200115#define CONFIG_SYS_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
Michael Barkowski5bbeea82008-03-20 13:15:34 -0400116 | (31 << TIMING_CFG2_CPO_SHIFT ) \
Michael Barkowskifc549c82008-03-20 13:15:28 -0400117 | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
118 | ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
119 | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
120 | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
Michael Barkowski5bbeea82008-03-20 13:15:34 -0400121 | ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) )
122 /* 0x1f9048c7 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200123#define CONFIG_SYS_DDR_TIMING_3 0x00000000
124#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
Michael Barkowskifc549c82008-03-20 13:15:28 -0400125 /* 0x02000000 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200126#define CONFIG_SYS_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
Michael Barkowskifc549c82008-03-20 13:15:28 -0400127 | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
Michael Barkowski5bbeea82008-03-20 13:15:34 -0400128 /* 0x44480232 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200129#define CONFIG_SYS_DDR_MODE2 0x8000c000
130#define CONFIG_SYS_DDR_INTERVAL ( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
Michael Barkowskifc549c82008-03-20 13:15:28 -0400131 | ( 100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
132 /* 0x03200064 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200133#define CONFIG_SYS_DDR_CS0_BNDS 0x00000003
134#define CONFIG_SYS_DDR_SDRAM_CFG ( SDRAM_CFG_SREN \
Michael Barkowskifc549c82008-03-20 13:15:28 -0400135 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
136 | SDRAM_CFG_32_BE )
137 /* 0x43080000 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200138#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
Kim Phillips1c274c42007-07-25 19:25:33 -0500139#endif
140
141/*
142 * Memory test
143 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200144#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
145#define CONFIG_SYS_MEMTEST_START 0x00030000 /* memtest region */
146#define CONFIG_SYS_MEMTEST_END 0x03f00000
Kim Phillips1c274c42007-07-25 19:25:33 -0500147
148/*
149 * The reserved memory
150 */
Wolfgang Denk14d0a022010-10-07 21:51:12 +0200151#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
Kim Phillips1c274c42007-07-25 19:25:33 -0500152
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200153#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
154#define CONFIG_SYS_RAMBOOT
Kim Phillips1c274c42007-07-25 19:25:33 -0500155#else
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200156#undef CONFIG_SYS_RAMBOOT
Kim Phillips1c274c42007-07-25 19:25:33 -0500157#endif
158
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200159/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
Kim Phillips4a9932a2009-07-07 18:04:21 -0500160#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200161#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
Kim Phillips1c274c42007-07-25 19:25:33 -0500162
163/*
164 * Initial RAM Base Address Setup
165 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200166#define CONFIG_SYS_INIT_RAM_LOCK 1
167#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
168#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */
169#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
170#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
Kim Phillips1c274c42007-07-25 19:25:33 -0500171
172/*
173 * Local Bus Configuration & Clock Setup
174 */
Kim Phillipsc7190f02009-09-25 18:19:44 -0500175#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
176#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200177#define CONFIG_SYS_LBC_LBCR 0x00000000
Kim Phillips1c274c42007-07-25 19:25:33 -0500178
179/*
180 * FLASH on the Local Bus
181 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200182#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
Jean-Christophe PLAGNIOL-VILLARD00b18832008-08-13 01:40:42 +0200183#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200184#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
185#define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size is 16M */
186#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
Kim Phillips1c274c42007-07-25 19:25:33 -0500187
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200188#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */
189#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */
Kim Phillips1c274c42007-07-25 19:25:33 -0500190
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200191#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | /* Flash Base address */ \
Kim Phillips1c274c42007-07-25 19:25:33 -0500192 (2 << BR_PS_SHIFT) | /* 16 bit port size */ \
193 BR_V) /* valid */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200194#define CONFIG_SYS_OR0_PRELIM 0xfe006ff7 /* 16MB Flash size */
Kim Phillips1c274c42007-07-25 19:25:33 -0500195
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200196#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
197#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
Kim Phillips1c274c42007-07-25 19:25:33 -0500198
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200199#undef CONFIG_SYS_FLASH_CHECKSUM
Kim Phillips1c274c42007-07-25 19:25:33 -0500200
201/*
202 * SDRAM on the Local Bus
203 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200204#undef CONFIG_SYS_LB_SDRAM /* The board has not SRDAM on local bus */
Kim Phillips1c274c42007-07-25 19:25:33 -0500205
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200206#ifdef CONFIG_SYS_LB_SDRAM
207#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */
208#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
Kim Phillips1c274c42007-07-25 19:25:33 -0500209
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200210#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE
211#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000019 /* 64MB */
Kim Phillips1c274c42007-07-25 19:25:33 -0500212
213/*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */
214/*
215 * Base Register 2 and Option Register 2 configure SDRAM.
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200216 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
Kim Phillips1c274c42007-07-25 19:25:33 -0500217 *
218 * For BR2, need:
219 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
220 * port size = 32-bits = BR2[19:20] = 11
221 * no parity checking = BR2[21:22] = 00
222 * SDRAM for MSEL = BR2[24:26] = 011
223 * Valid = BR[31] = 1
224 *
225 * 0 4 8 12 16 20 24 28
226 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
227 *
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200228 * CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
Kim Phillips1c274c42007-07-25 19:25:33 -0500229 * the top 17 bits of BR2.
230 */
231
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200232#define CONFIG_SYS_BR2_PRELIM 0xf0001861 /*Port size=32bit, MSEL=SDRAM */
Kim Phillips1c274c42007-07-25 19:25:33 -0500233
234/*
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200235 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
Kim Phillips1c274c42007-07-25 19:25:33 -0500236 *
237 * For OR2, need:
238 * 64MB mask for AM, OR2[0:7] = 1111 1100
239 * XAM, OR2[17:18] = 11
240 * 9 columns OR2[19-21] = 010
241 * 13 rows OR2[23-25] = 100
242 * EAD set for extra time OR[31] = 1
243 *
244 * 0 4 8 12 16 20 24 28
245 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
246 */
247
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200248#define CONFIG_SYS_OR2_PRELIM 0xfc006901
Kim Phillips1c274c42007-07-25 19:25:33 -0500249
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200250#define CONFIG_SYS_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
251#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */
Kim Phillips1c274c42007-07-25 19:25:33 -0500252
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200253#define CONFIG_SYS_LBC_LSDMR_COMMON 0x0063b723
Kim Phillips1c274c42007-07-25 19:25:33 -0500254
Kim Phillips1c274c42007-07-25 19:25:33 -0500255#endif
256
257/*
258 * Windows to access PIB via local bus
259 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200260#define CONFIG_SYS_LBLAWBAR3_PRELIM 0xf8008000 /* windows base 0xf8008000 */
261#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000f /* windows size 64KB */
Kim Phillips1c274c42007-07-25 19:25:33 -0500262
263/*
264 * Serial Port
265 */
266#define CONFIG_CONS_INDEX 1
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200267#define CONFIG_SYS_NS16550
268#define CONFIG_SYS_NS16550_SERIAL
269#define CONFIG_SYS_NS16550_REG_SIZE 1
270#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
Kim Phillips1c274c42007-07-25 19:25:33 -0500271
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200272#define CONFIG_SYS_BAUDRATE_TABLE \
Kim Phillips1c274c42007-07-25 19:25:33 -0500273 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
274
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200275#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
276#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
Kim Phillips1c274c42007-07-25 19:25:33 -0500277
278#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
Kim Phillipsa059e902010-04-15 17:36:05 -0500279#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
Kim Phillips1c274c42007-07-25 19:25:33 -0500280/* Use the HUSH parser */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200281#define CONFIG_SYS_HUSH_PARSER
282#ifdef CONFIG_SYS_HUSH_PARSER
283#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
Kim Phillips1c274c42007-07-25 19:25:33 -0500284#endif
285
286/* pass open firmware flat tree */
287#define CONFIG_OF_LIBFDT 1
288#define CONFIG_OF_BOARD_SETUP 1
Kim Phillips5b8bc602007-12-20 14:09:22 -0600289#define CONFIG_OF_STDOUT_VIA_ALIAS 1
Kim Phillips1c274c42007-07-25 19:25:33 -0500290
291/* I2C */
292#define CONFIG_HARD_I2C /* I2C with hardware support */
293#undef CONFIG_SOFT_I2C /* I2C bit-banged */
294#define CONFIG_FSL_I2C
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200295#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
296#define CONFIG_SYS_I2C_SLAVE 0x7F
297#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */
298#define CONFIG_SYS_I2C_OFFSET 0x3000
Kim Phillips1c274c42007-07-25 19:25:33 -0500299
300/*
Michael Barkowski0fa7a1b2008-03-20 13:15:39 -0400301 * Config on-board EEPROM
Kim Phillips1c274c42007-07-25 19:25:33 -0500302 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200303#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
304#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
305#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
306#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
Kim Phillips1c274c42007-07-25 19:25:33 -0500307
308/*
309 * General PCI
310 * Addresses are mapped 1-1.
311 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200312#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
313#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
314#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
315#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
316#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
317#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
318#define CONFIG_SYS_PCI1_IO_BASE 0xd0000000
319#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
320#define CONFIG_SYS_PCI1_IO_SIZE 0x04000000 /* 64M */
Kim Phillips1c274c42007-07-25 19:25:33 -0500321
322#ifdef CONFIG_PCI
Michael Barkowski8f325cf2008-03-28 15:15:38 -0400323#define CONFIG_PCI_SKIP_HOST_BRIDGE
Kim Phillips1c274c42007-07-25 19:25:33 -0500324#define CONFIG_NET_MULTI
325#define CONFIG_PCI_PNP /* do pci plug-and-play */
326
327#undef CONFIG_EEPRO100
328#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200329#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
Kim Phillips1c274c42007-07-25 19:25:33 -0500330
331#endif /* CONFIG_PCI */
332
333
334#ifndef CONFIG_NET_MULTI
335#define CONFIG_NET_MULTI 1
336#endif
337
338/*
339 * QE UEC ethernet configuration
340 */
341#define CONFIG_UEC_ETH
Kim Phillips78b7a8e2010-07-26 18:34:57 -0500342#define CONFIG_ETHPRIME "UEC0"
Kim Phillips1c274c42007-07-25 19:25:33 -0500343
344#define CONFIG_UEC_ETH1 /* ETH3 */
345
346#ifdef CONFIG_UEC_ETH1
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200347#define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */
348#define CONFIG_SYS_UEC1_RX_CLK QE_CLK9
349#define CONFIG_SYS_UEC1_TX_CLK QE_CLK10
350#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
351#define CONFIG_SYS_UEC1_PHY_ADDR 4
Heiko Schocher582c55a2010-01-20 09:04:28 +0100352#define CONFIG_SYS_UEC1_INTERFACE_TYPE MII
353#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
Kim Phillips1c274c42007-07-25 19:25:33 -0500354#endif
355
356#define CONFIG_UEC_ETH2 /* ETH4 */
357
358#ifdef CONFIG_UEC_ETH2
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200359#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */
360#define CONFIG_SYS_UEC2_RX_CLK QE_CLK16
361#define CONFIG_SYS_UEC2_TX_CLK QE_CLK3
362#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
363#define CONFIG_SYS_UEC2_PHY_ADDR 0
Heiko Schocher582c55a2010-01-20 09:04:28 +0100364#define CONFIG_SYS_UEC2_INTERFACE_TYPE MII
365#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
Kim Phillips1c274c42007-07-25 19:25:33 -0500366#endif
367
368/*
369 * Environment
370 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200371#ifndef CONFIG_SYS_RAMBOOT
Jean-Christophe PLAGNIOL-VILLARD5a1aceb2008-09-10 22:48:04 +0200372 #define CONFIG_ENV_IS_IN_FLASH 1
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200373 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +0200374 #define CONFIG_ENV_SECT_SIZE 0x20000
375 #define CONFIG_ENV_SIZE 0x2000
Kim Phillips1c274c42007-07-25 19:25:33 -0500376#else
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200377 #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
Jean-Christophe PLAGNIOL-VILLARD93f6d722008-09-10 22:48:00 +0200378 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200379 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +0200380 #define CONFIG_ENV_SIZE 0x2000
Kim Phillips1c274c42007-07-25 19:25:33 -0500381#endif
382
383#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200384#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
Kim Phillips1c274c42007-07-25 19:25:33 -0500385
386/*
387 * BOOTP options
388 */
389#define CONFIG_BOOTP_BOOTFILESIZE
390#define CONFIG_BOOTP_BOOTPATH
391#define CONFIG_BOOTP_GATEWAY
392#define CONFIG_BOOTP_HOSTNAME
393
394/*
395 * Command line configuration.
396 */
397#include <config_cmd_default.h>
398
399#define CONFIG_CMD_PING
400#define CONFIG_CMD_I2C
Michael Barkowski0fa7a1b2008-03-20 13:15:39 -0400401#define CONFIG_CMD_EEPROM
Kim Phillips1c274c42007-07-25 19:25:33 -0500402#define CONFIG_CMD_ASKENV
403
404#if defined(CONFIG_PCI)
405 #define CONFIG_CMD_PCI
406#endif
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200407#if defined(CONFIG_SYS_RAMBOOT)
Mike Frysingerbdab39d2009-01-28 19:08:14 -0500408 #undef CONFIG_CMD_SAVEENV
Kim Phillips1c274c42007-07-25 19:25:33 -0500409 #undef CONFIG_CMD_LOADS
410#endif
411
412#undef CONFIG_WATCHDOG /* watchdog disabled */
413
414/*
415 * Miscellaneous configurable options
416 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200417#define CONFIG_SYS_LONGHELP /* undef to save memory */
418#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
419#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
Kim Phillips1c274c42007-07-25 19:25:33 -0500420
421#if (CONFIG_CMD_KGDB)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200422 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
Kim Phillips1c274c42007-07-25 19:25:33 -0500423#else
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200424 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
Kim Phillips1c274c42007-07-25 19:25:33 -0500425#endif
426
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200427#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
428#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
429#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
430#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
Kim Phillips1c274c42007-07-25 19:25:33 -0500431
432/*
433 * For booting Linux, the board info and command line data
Ira W. Snyder9f530d52010-09-10 15:42:32 -0700434 * have to be in the first 256 MB of memory, since this is
Kim Phillips1c274c42007-07-25 19:25:33 -0500435 * the maximum mapped by the Linux kernel during initialization.
436 */
Ira W. Snyder9f530d52010-09-10 15:42:32 -0700437#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
Kim Phillips1c274c42007-07-25 19:25:33 -0500438
439/*
440 * Core HID Setup
441 */
Kim Phillips1a2e2032010-04-20 19:37:54 -0500442#define CONFIG_SYS_HID0_INIT 0x000000000
443#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
444 HID0_ENABLE_INSTRUCTION_CACHE)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200445#define CONFIG_SYS_HID2 HID2_HBE
Kim Phillips1c274c42007-07-25 19:25:33 -0500446
447/*
Kim Phillips1c274c42007-07-25 19:25:33 -0500448 * MMU Setup
449 */
Becky Bruce31d82672008-05-08 19:02:12 -0500450#define CONFIG_HIGH_BATS 1 /* High BATs supported */
Kim Phillips1c274c42007-07-25 19:25:33 -0500451
452/* DDR: cache cacheable */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200453#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
454#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
455#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
456#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
Kim Phillips1c274c42007-07-25 19:25:33 -0500457
458/* IMMRBAR & PCI IO: cache-inhibit and guarded */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200459#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \
Kim Phillips1c274c42007-07-25 19:25:33 -0500460 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200461#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
462#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
463#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
Kim Phillips1c274c42007-07-25 19:25:33 -0500464
465/* FLASH: icache cacheable, but dcache-inhibit and guarded */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200466#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
467#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
468#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
Kim Phillips1c274c42007-07-25 19:25:33 -0500469 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200470#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
Kim Phillips1c274c42007-07-25 19:25:33 -0500471
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200472#define CONFIG_SYS_IBAT3L (0)
473#define CONFIG_SYS_IBAT3U (0)
474#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
475#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
Kim Phillips1c274c42007-07-25 19:25:33 -0500476
477/* Stack in dcache: cacheable, no memory coherence */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200478#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
479#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
480#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
481#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
Kim Phillips1c274c42007-07-25 19:25:33 -0500482
483#ifdef CONFIG_PCI
484/* PCI MEM space: cacheable */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200485#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
486#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
487#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
488#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
Kim Phillips1c274c42007-07-25 19:25:33 -0500489/* PCI MMIO space: cache-inhibit and guarded */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200490#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MMIO_PHYS | BATL_PP_10 | \
Kim Phillips1c274c42007-07-25 19:25:33 -0500491 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200492#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
493#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
494#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
Kim Phillips1c274c42007-07-25 19:25:33 -0500495#else
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200496#define CONFIG_SYS_IBAT5L (0)
497#define CONFIG_SYS_IBAT5U (0)
498#define CONFIG_SYS_IBAT6L (0)
499#define CONFIG_SYS_IBAT6U (0)
500#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
501#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
502#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
503#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
Kim Phillips1c274c42007-07-25 19:25:33 -0500504#endif
505
506/* Nothing in BAT7 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200507#define CONFIG_SYS_IBAT7L (0)
508#define CONFIG_SYS_IBAT7U (0)
509#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
510#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
Kim Phillips1c274c42007-07-25 19:25:33 -0500511
Kim Phillips1c274c42007-07-25 19:25:33 -0500512#if (CONFIG_CMD_KGDB)
513#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
514#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
515#endif
516
517/*
518 * Environment Configuration
519 */
520#define CONFIG_ENV_OVERWRITE
521
Kim Phillips977b5752008-01-09 15:24:06 -0600522#define CONFIG_HAS_ETH0 /* add support for "ethaddr" */
Kim Phillips1c274c42007-07-25 19:25:33 -0500523#define CONFIG_HAS_ETH1 /* add support for "eth1addr" */
Kim Phillips1c274c42007-07-25 19:25:33 -0500524
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200525/* use mac_read_from_eeprom() to read ethaddr from I2C EEPROM (see CONFIG_SYS_I2C_EEPROM) */
526#define CONFIG_SYS_I2C_MAC_OFFSET 0x7f00 /* MAC address offset in I2C EEPROM */
Michael Barkowski5b2793a2008-03-27 14:34:43 -0400527
Kim Phillips1c274c42007-07-25 19:25:33 -0500528#define CONFIG_NETDEV eth1
529
530#define CONFIG_HOSTNAME mpc8323erdb
531#define CONFIG_ROOTPATH /nfsroot
532#define CONFIG_RAMDISKFILE rootfs.ext2.gz.uboot
533#define CONFIG_BOOTFILE uImage
534#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
535#define CONFIG_FDTFILE mpc832x_rdb.dtb
536
Kim Phillips79f516b2009-08-21 16:34:38 -0500537#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
Kim Phillips7fd0bea2008-09-24 08:46:25 -0500538#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
Kim Phillips1c274c42007-07-25 19:25:33 -0500539#define CONFIG_BAUDRATE 115200
540
541#define XMK_STR(x) #x
542#define MK_STR(x) XMK_STR(x)
543
544#define CONFIG_EXTRA_ENV_SETTINGS \
545 "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
546 "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
547 "tftpflash=tftp $loadaddr $uboot;" \
Wolfgang Denk14d0a022010-10-07 21:51:12 +0200548 "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
549 "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
550 "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; " \
551 "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
552 "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
Kim Phillips79f516b2009-08-21 16:34:38 -0500553 "fdtaddr=780000\0" \
Kim Phillips1c274c42007-07-25 19:25:33 -0500554 "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
555 "ramdiskaddr=1000000\0" \
556 "ramdiskfile=" MK_STR(CONFIG_RAMDISKFILE) "\0" \
557 "console=ttyS0\0" \
558 "setbootargs=setenv bootargs " \
559 "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
560 "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
561 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
562 "root=$rootdev rw console=$console,$baudrate $othbootargs\0"
563
564#define CONFIG_NFSBOOTCOMMAND \
565 "setenv rootdev /dev/nfs;" \
566 "run setbootargs;" \
567 "run setipargs;" \
568 "tftp $loadaddr $bootfile;" \
569 "tftp $fdtaddr $fdtfile;" \
570 "bootm $loadaddr - $fdtaddr"
571
572#define CONFIG_RAMBOOTCOMMAND \
573 "setenv rootdev /dev/ram;" \
574 "run setbootargs;" \
575 "tftp $ramdiskaddr $ramdiskfile;" \
576 "tftp $loadaddr $bootfile;" \
577 "tftp $fdtaddr $fdtfile;" \
578 "bootm $loadaddr $ramdiskaddr $fdtaddr"
579
580#undef MK_STR
581#undef XMK_STR
582
583#endif /* __CONFIG_H */