blob: e7e78e3c56d71a6bc58dde0c80260b91d649fd7f [file] [log] [blame]
Tom Rini83d290c2018-05-06 17:58:06 -04001// SPDX-License-Identifier: GPL-2.0+
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +02002/*
3 * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
4 * Written by Jean-Jacques Hiblot <jjhiblot@ti.com>
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +02005 */
6
7#include <common.h>
8#include <dm.h>
9#include <dm/device.h>
10#include <generic-phy.h>
11#include <asm/io.h>
12#include <asm/arch/sys_proto.h>
13#include <syscon.h>
14#include <regmap.h>
15
16/* PLLCTRL Registers */
17#define PLL_STATUS 0x00000004
18#define PLL_GO 0x00000008
19#define PLL_CONFIGURATION1 0x0000000C
20#define PLL_CONFIGURATION2 0x00000010
21#define PLL_CONFIGURATION3 0x00000014
22#define PLL_CONFIGURATION4 0x00000020
23
24#define PLL_REGM_MASK 0x001FFE00
25#define PLL_REGM_SHIFT 9
26#define PLL_REGM_F_MASK 0x0003FFFF
27#define PLL_REGM_F_SHIFT 0
28#define PLL_REGN_MASK 0x000001FE
29#define PLL_REGN_SHIFT 1
30#define PLL_SELFREQDCO_MASK 0x0000000E
31#define PLL_SELFREQDCO_SHIFT 1
32#define PLL_SD_MASK 0x0003FC00
33#define PLL_SD_SHIFT 10
34#define SET_PLL_GO 0x1
35#define PLL_TICOPWDN BIT(16)
36#define PLL_LDOPWDN BIT(15)
37#define PLL_LOCK 0x2
38#define PLL_IDLE 0x1
39
40/* Software rest for the SATA PLL (in CTRL_CORE_SMA_SW_0 register)*/
41#define SATA_PLL_SOFT_RESET (1<<18)
42
43/* PHY POWER CONTROL Register */
44#define OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK 0x003FC000
45#define OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT 0xE
46
47#define OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK 0xFFC00000
48#define OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT 0x16
49
50#define OMAP_CTRL_PIPE3_PHY_TX_RX_POWERON 0x3
51#define OMAP_CTRL_PIPE3_PHY_TX_RX_POWEROFF 0x0
52
53
54#define PLL_IDLE_TIME 100 /* in milliseconds */
55#define PLL_LOCK_TIME 100 /* in milliseconds */
56
57struct omap_pipe3 {
58 void __iomem *pll_ctrl_base;
59 void __iomem *power_reg;
60 void __iomem *pll_reset_reg;
61 struct pipe3_dpll_map *dpll_map;
62};
63
64
65struct pipe3_dpll_params {
66 u16 m;
67 u8 n;
68 u8 freq:3;
69 u8 sd;
70 u32 mf;
71};
72
73struct pipe3_dpll_map {
74 unsigned long rate;
75 struct pipe3_dpll_params params;
76};
77
78static inline u32 omap_pipe3_readl(void __iomem *addr, unsigned offset)
79{
80 return readl(addr + offset);
81}
82
83static inline void omap_pipe3_writel(void __iomem *addr, unsigned offset,
84 u32 data)
85{
86 writel(data, addr + offset);
87}
88
89static struct pipe3_dpll_params *omap_pipe3_get_dpll_params(struct omap_pipe3
90 *pipe3)
91{
92 u32 rate;
93 struct pipe3_dpll_map *dpll_map = pipe3->dpll_map;
94
95 rate = get_sys_clk_freq();
96
97 for (; dpll_map->rate; dpll_map++) {
98 if (rate == dpll_map->rate)
99 return &dpll_map->params;
100 }
101
102 printf("%s: No DPLL configuration for %u Hz SYS CLK\n",
103 __func__, rate);
104 return NULL;
105}
106
107static int omap_pipe3_wait_lock(struct omap_pipe3 *pipe3)
108{
109 u32 val;
110 int timeout = PLL_LOCK_TIME;
111
112 do {
113 mdelay(1);
114 val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_STATUS);
115 if (val & PLL_LOCK)
116 break;
117 } while (--timeout);
118
119 if (!(val & PLL_LOCK)) {
120 printf("%s: DPLL failed to lock\n", __func__);
121 return -EBUSY;
122 }
123
124 return 0;
125}
126
127static int omap_pipe3_dpll_program(struct omap_pipe3 *pipe3)
128{
129 u32 val;
130 struct pipe3_dpll_params *dpll_params;
131
132 dpll_params = omap_pipe3_get_dpll_params(pipe3);
133 if (!dpll_params) {
134 printf("%s: Invalid DPLL parameters\n", __func__);
135 return -EINVAL;
136 }
137
138 val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION1);
139 val &= ~PLL_REGN_MASK;
140 val |= dpll_params->n << PLL_REGN_SHIFT;
141 omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION1, val);
142
143 val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION2);
Vignesh R0752d702018-11-29 10:57:38 +0100144 val &= ~(PLL_SELFREQDCO_MASK | PLL_IDLE);
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200145 val |= dpll_params->freq << PLL_SELFREQDCO_SHIFT;
146 omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION2, val);
147
148 val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION1);
149 val &= ~PLL_REGM_MASK;
150 val |= dpll_params->m << PLL_REGM_SHIFT;
151 omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION1, val);
152
153 val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION4);
154 val &= ~PLL_REGM_F_MASK;
155 val |= dpll_params->mf << PLL_REGM_F_SHIFT;
156 omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION4, val);
157
158 val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION3);
159 val &= ~PLL_SD_MASK;
160 val |= dpll_params->sd << PLL_SD_SHIFT;
161 omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION3, val);
162
163 omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_GO, SET_PLL_GO);
164
165 return omap_pipe3_wait_lock(pipe3);
166}
167
168static void omap_control_pipe3_power(struct omap_pipe3 *pipe3, int on)
169{
170 u32 val, rate;
171
172 val = readl(pipe3->power_reg);
173
174 rate = get_sys_clk_freq();
175 rate = rate/1000000;
176
177 if (on) {
178 val &= ~(OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK |
179 OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK);
180 val |= OMAP_CTRL_PIPE3_PHY_TX_RX_POWERON <<
181 OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
182 val |= rate <<
183 OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT;
184 } else {
185 val &= ~OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK;
186 val |= OMAP_CTRL_PIPE3_PHY_TX_RX_POWEROFF <<
187 OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
188 }
189
190 writel(val, pipe3->power_reg);
191}
192
193static int pipe3_init(struct phy *phy)
194{
195 int ret;
196 u32 val;
197 struct omap_pipe3 *pipe3 = dev_get_priv(phy->dev);
198
199 /* Program the DPLL only if not locked */
200 val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_STATUS);
201 if (!(val & PLL_LOCK)) {
202 ret = omap_pipe3_dpll_program(pipe3);
203 if (ret)
204 return ret;
205 } else {
206 /* else just bring it out of IDLE mode */
207 val = omap_pipe3_readl(pipe3->pll_ctrl_base,
208 PLL_CONFIGURATION2);
209 if (val & PLL_IDLE) {
210 val &= ~PLL_IDLE;
211 omap_pipe3_writel(pipe3->pll_ctrl_base,
212 PLL_CONFIGURATION2, val);
213 ret = omap_pipe3_wait_lock(pipe3);
214 if (ret)
215 return ret;
216 }
217 }
218 return 0;
219}
220
221static int pipe3_power_on(struct phy *phy)
222{
223 struct omap_pipe3 *pipe3 = dev_get_priv(phy->dev);
224
225 /* Power up the PHY */
226 omap_control_pipe3_power(pipe3, 1);
227
228 return 0;
229}
230
231static int pipe3_power_off(struct phy *phy)
232{
233 struct omap_pipe3 *pipe3 = dev_get_priv(phy->dev);
234
235 /* Power down the PHY */
236 omap_control_pipe3_power(pipe3, 0);
237
238 return 0;
239}
240
241static int pipe3_exit(struct phy *phy)
242{
243 u32 val;
244 int timeout = PLL_IDLE_TIME;
245 struct omap_pipe3 *pipe3 = dev_get_priv(phy->dev);
246
247 pipe3_power_off(phy);
248
249 /* Put DPLL in IDLE mode */
250 val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION2);
251 val |= PLL_IDLE;
252 omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION2, val);
253
254 /* wait for LDO and Oscillator to power down */
255 do {
256 mdelay(1);
257 val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_STATUS);
258 if ((val & PLL_TICOPWDN) && (val & PLL_LDOPWDN))
259 break;
260 } while (--timeout);
261
262 if (!(val & PLL_TICOPWDN) || !(val & PLL_LDOPWDN)) {
Masahiro Yamada9b643e32017-09-16 14:10:41 +0900263 pr_err("%s: Failed to power down DPLL: PLL_STATUS 0x%x\n",
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200264 __func__, val);
265 return -EBUSY;
266 }
267
Vignesh R0752d702018-11-29 10:57:38 +0100268 if (pipe3->pll_reset_reg) {
269 val = readl(pipe3->pll_reset_reg);
270 writel(val | SATA_PLL_SOFT_RESET, pipe3->pll_reset_reg);
271 mdelay(1);
272 writel(val & ~SATA_PLL_SOFT_RESET, pipe3->pll_reset_reg);
273 }
274
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200275 return 0;
276}
277
278static void *get_reg(struct udevice *dev, const char *name)
279{
280 struct udevice *syscon;
281 struct regmap *regmap;
282 const fdt32_t *cell;
283 int len, err;
284 void *base;
285
286 err = uclass_get_device_by_phandle(UCLASS_SYSCON, dev,
287 name, &syscon);
288 if (err) {
Masahiro Yamada9b643e32017-09-16 14:10:41 +0900289 pr_err("unable to find syscon device for %s (%d)\n",
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200290 name, err);
291 return NULL;
292 }
293
294 regmap = syscon_get_regmap(syscon);
295 if (IS_ERR(regmap)) {
Masahiro Yamada9b643e32017-09-16 14:10:41 +0900296 pr_err("unable to find regmap for %s (%ld)\n",
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200297 name, PTR_ERR(regmap));
298 return NULL;
299 }
300
Simon Glassda409cc2017-05-17 17:18:09 -0600301 cell = fdt_getprop(gd->fdt_blob, dev_of_offset(dev), name,
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200302 &len);
303 if (len < 2*sizeof(fdt32_t)) {
Masahiro Yamada9b643e32017-09-16 14:10:41 +0900304 pr_err("offset not available for %s\n", name);
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200305 return NULL;
306 }
307
308 base = regmap_get_range(regmap, 0);
309 if (!base)
310 return NULL;
311
312 return fdtdec_get_number(cell + 1, 1) + base;
313}
314
315static int pipe3_phy_probe(struct udevice *dev)
316{
317 fdt_addr_t addr;
318 fdt_size_t sz;
319 struct omap_pipe3 *pipe3 = dev_get_priv(dev);
320
Simon Glassa821c4a2017-05-17 17:18:05 -0600321 addr = devfdt_get_addr_size_index(dev, 2, &sz);
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200322 if (addr == FDT_ADDR_T_NONE) {
Masahiro Yamada9b643e32017-09-16 14:10:41 +0900323 pr_err("missing pll ctrl address\n");
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200324 return -EINVAL;
325 }
326
327 pipe3->pll_ctrl_base = map_physmem(addr, sz, MAP_NOCACHE);
328 if (!pipe3->pll_ctrl_base) {
Masahiro Yamada9b643e32017-09-16 14:10:41 +0900329 pr_err("unable to remap pll ctrl\n");
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200330 return -EINVAL;
331 }
332
333 pipe3->power_reg = get_reg(dev, "syscon-phy-power");
334 if (!pipe3->power_reg)
335 return -EINVAL;
336
Vignesh R0752d702018-11-29 10:57:38 +0100337 if (device_is_compatible(dev, "ti,phy-pipe3-sata")) {
338 pipe3->pll_reset_reg = get_reg(dev, "syscon-pllreset");
339 if (!pipe3->pll_reset_reg)
340 return -EINVAL;
341 }
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200342
343 pipe3->dpll_map = (struct pipe3_dpll_map *)dev_get_driver_data(dev);
344
345 return 0;
346}
347
348static struct pipe3_dpll_map dpll_map_sata[] = {
349 {12000000, {1000, 7, 4, 6, 0} }, /* 12 MHz */
350 {16800000, {714, 7, 4, 6, 0} }, /* 16.8 MHz */
351 {19200000, {625, 7, 4, 6, 0} }, /* 19.2 MHz */
352 {20000000, {600, 7, 4, 6, 0} }, /* 20 MHz */
353 {26000000, {461, 7, 4, 6, 0} }, /* 26 MHz */
354 {38400000, {312, 7, 4, 6, 0} }, /* 38.4 MHz */
355 { }, /* Terminator */
356};
357
Vignesh R0752d702018-11-29 10:57:38 +0100358static struct pipe3_dpll_map dpll_map_usb[] = {
359 {12000000, {1250, 5, 4, 20, 0} }, /* 12 MHz */
360 {16800000, {3125, 20, 4, 20, 0} }, /* 16.8 MHz */
361 {19200000, {1172, 8, 4, 20, 65537} }, /* 19.2 MHz */
362 {20000000, {1000, 7, 4, 10, 0} }, /* 20 MHz */
363 {26000000, {1250, 12, 4, 20, 0} }, /* 26 MHz */
364 {38400000, {3125, 47, 4, 20, 92843} }, /* 38.4 MHz */
365 { }, /* Terminator */
366};
367
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200368static const struct udevice_id pipe3_phy_ids[] = {
369 { .compatible = "ti,phy-pipe3-sata", .data = (ulong)&dpll_map_sata },
Vignesh R0752d702018-11-29 10:57:38 +0100370 { .compatible = "ti,omap-usb3", .data = (ulong)&dpll_map_usb},
Jean-Jacques Hiblot982082d2017-04-24 11:51:29 +0200371 { }
372};
373
374static struct phy_ops pipe3_phy_ops = {
375 .init = pipe3_init,
376 .power_on = pipe3_power_on,
377 .power_off = pipe3_power_off,
378 .exit = pipe3_exit,
379};
380
381U_BOOT_DRIVER(pipe3_phy) = {
382 .name = "pipe3_phy",
383 .id = UCLASS_PHY,
384 .of_match = pipe3_phy_ids,
385 .ops = &pipe3_phy_ops,
386 .probe = pipe3_phy_probe,
387 .priv_auto_alloc_size = sizeof(struct omap_pipe3),
388};