blob: f9c32dd65d7b297678eb77b819a2e7519013dc96 [file] [log] [blame]
wdenkfe8c2802002-11-03 00:38:21 +00001/*
2 * Cirrus Logic CS8900A Ethernet
3 *
4 * (C) Copyright 2002
5 * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
6 * Marius Groeger <mgroeger@sysgo.de>
7 *
8 * Copyright (C) 1999 Ben Williamson <benw@pobox.com>
9 *
10 * See file CREDITS for list of people who contributed to this
11 * project.
12 *
13 * This program is loaded into SRAM in bootstrap mode, where it waits
14 * for commands on UART1 to read and write memory, jump to code etc.
15 * A design goal for this program is to be entirely independent of the
16 * target board. Anything with a CL-PS7111 or EP7211 should be able to run
17 * this code in bootstrap mode. All the board specifics can be handled on
18 * the host.
19 *
20 * This program is free software; you can redistribute it and/or modify
21 * it under the terms of the GNU General Public License as published by
22 * the Free Software Foundation; either version 2 of the License, or
23 * (at your option) any later version.
24 *
25 * This program is distributed in the hope that it will be useful,
26 * but WITHOUT ANY WARRANTY; without even the implied warranty of
27 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
28 * GNU General Public License for more details.
29 *
30 * You should have received a copy of the GNU General Public License
31 * along with this program; if not, write to the Free Software
32 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
33 */
34
35#include <asm/types.h>
36#include <config.h>
37
38#ifdef CONFIG_DRIVER_CS8900
39
40/* although the registers are 16 bit, they are 32-bit aligned on the
41 EDB7111. so we have to read them as 32-bit registers and ignore the
42 upper 16-bits. i'm not sure if this holds for the EDB7211. */
43
44#ifdef CS8900_BUS16
45 /* 16 bit aligned registers, 16 bit wide */
46 #define CS8900_REG u16
47 #define CS8900_OFF 0x02
48 #define CS8900_BUS16_0 *(volatile u8 *)(CS8900_BASE+0x00)
49 #define CS8900_BUS16_1 *(volatile u8 *)(CS8900_BASE+0x01)
wdenk42dfe7a2004-03-14 22:25:36 +000050#elif defined(CS8900_BUS32)
wdenkfe8c2802002-11-03 00:38:21 +000051 /* 32 bit aligned registers, 16 bit wide (we ignore upper 16 bits) */
52 #define CS8900_REG u32
53 #define CS8900_OFF 0x04
54#else
55 #error unknown bussize ...
56#endif
57
58#define CS8900_RTDATA *(volatile CS8900_REG *)(CS8900_BASE+0x00*CS8900_OFF)
59#define CS8900_TxCMD *(volatile CS8900_REG *)(CS8900_BASE+0x02*CS8900_OFF)
60#define CS8900_TxLEN *(volatile CS8900_REG *)(CS8900_BASE+0x03*CS8900_OFF)
61#define CS8900_ISQ *(volatile CS8900_REG *)(CS8900_BASE+0x04*CS8900_OFF)
62#define CS8900_PPTR *(volatile CS8900_REG *)(CS8900_BASE+0x05*CS8900_OFF)
63#define CS8900_PDATA *(volatile CS8900_REG *)(CS8900_BASE+0x06*CS8900_OFF)
64
65
66#define ISQ_RxEvent 0x04
67#define ISQ_TxEvent 0x08
68#define ISQ_BufEvent 0x0C
69#define ISQ_RxMissEvent 0x10
70#define ISQ_TxColEvent 0x12
71#define ISQ_EventMask 0x3F
72
73/* packet page register offsets */
74
75/* bus interface registers */
76#define PP_ChipID 0x0000 /* Chip identifier - must be 0x630E */
77#define PP_ChipRev 0x0002 /* Chip revision, model codes */
78
79#define PP_IntReg 0x0022 /* Interrupt configuration */
80#define PP_IntReg_IRQ0 0x0000 /* Use INTR0 pin */
81#define PP_IntReg_IRQ1 0x0001 /* Use INTR1 pin */
82#define PP_IntReg_IRQ2 0x0002 /* Use INTR2 pin */
83#define PP_IntReg_IRQ3 0x0003 /* Use INTR3 pin */
84
85/* status and control registers */
86
87#define PP_RxCFG 0x0102 /* Receiver configuration */
88#define PP_RxCFG_Skip1 0x0040 /* Skip (i.e. discard) current frame */
89#define PP_RxCFG_Stream 0x0080 /* Enable streaming mode */
90#define PP_RxCFG_RxOK 0x0100 /* RxOK interrupt enable */
91#define PP_RxCFG_RxDMAonly 0x0200 /* Use RxDMA for all frames */
92#define PP_RxCFG_AutoRxDMA 0x0400 /* Select RxDMA automatically */
93#define PP_RxCFG_BufferCRC 0x0800 /* Include CRC characters in frame */
94#define PP_RxCFG_CRC 0x1000 /* Enable interrupt on CRC error */
95#define PP_RxCFG_RUNT 0x2000 /* Enable interrupt on RUNT frames */
96#define PP_RxCFG_EXTRA 0x4000 /* Enable interrupt on frames with extra data */
97
98#define PP_RxCTL 0x0104 /* Receiver control */
99#define PP_RxCTL_IAHash 0x0040 /* Accept frames that match hash */
100#define PP_RxCTL_Promiscuous 0x0080 /* Accept any frame */
101#define PP_RxCTL_RxOK 0x0100 /* Accept well formed frames */
102#define PP_RxCTL_Multicast 0x0200 /* Accept multicast frames */
103#define PP_RxCTL_IA 0x0400 /* Accept frame that matches IA */
104#define PP_RxCTL_Broadcast 0x0800 /* Accept broadcast frames */
105#define PP_RxCTL_CRC 0x1000 /* Accept frames with bad CRC */
106#define PP_RxCTL_RUNT 0x2000 /* Accept runt frames */
107#define PP_RxCTL_EXTRA 0x4000 /* Accept frames that are too long */
108
109#define PP_TxCFG 0x0106 /* Transmit configuration */
110#define PP_TxCFG_CRS 0x0040 /* Enable interrupt on loss of carrier */
111#define PP_TxCFG_SQE 0x0080 /* Enable interrupt on Signal Quality Error */
112#define PP_TxCFG_TxOK 0x0100 /* Enable interrupt on successful xmits */
113#define PP_TxCFG_Late 0x0200 /* Enable interrupt on "out of window" */
114#define PP_TxCFG_Jabber 0x0400 /* Enable interrupt on jabber detect */
115#define PP_TxCFG_Collision 0x0800 /* Enable interrupt if collision */
116#define PP_TxCFG_16Collisions 0x8000 /* Enable interrupt if > 16 collisions */
117
118#define PP_TxCmd 0x0108 /* Transmit command status */
119#define PP_TxCmd_TxStart_5 0x0000 /* Start after 5 bytes in buffer */
120#define PP_TxCmd_TxStart_381 0x0040 /* Start after 381 bytes in buffer */
121#define PP_TxCmd_TxStart_1021 0x0080 /* Start after 1021 bytes in buffer */
122#define PP_TxCmd_TxStart_Full 0x00C0 /* Start after all bytes loaded */
123#define PP_TxCmd_Force 0x0100 /* Discard any pending packets */
124#define PP_TxCmd_OneCollision 0x0200 /* Abort after a single collision */
125#define PP_TxCmd_NoCRC 0x1000 /* Do not add CRC */
126#define PP_TxCmd_NoPad 0x2000 /* Do not pad short packets */
127
128#define PP_BufCFG 0x010A /* Buffer configuration */
129#define PP_BufCFG_SWI 0x0040 /* Force interrupt via software */
130#define PP_BufCFG_RxDMA 0x0080 /* Enable interrupt on Rx DMA */
131#define PP_BufCFG_TxRDY 0x0100 /* Enable interrupt when ready for Tx */
132#define PP_BufCFG_TxUE 0x0200 /* Enable interrupt in Tx underrun */
133#define PP_BufCFG_RxMiss 0x0400 /* Enable interrupt on missed Rx packets */
134#define PP_BufCFG_Rx128 0x0800 /* Enable Rx interrupt after 128 bytes */
135#define PP_BufCFG_TxCol 0x1000 /* Enable int on Tx collision ctr overflow */
136#define PP_BufCFG_Miss 0x2000 /* Enable int on Rx miss ctr overflow */
137#define PP_BufCFG_RxDest 0x8000 /* Enable int on Rx dest addr match */
138
139#define PP_LineCTL 0x0112 /* Line control */
140#define PP_LineCTL_Rx 0x0040 /* Enable receiver */
141#define PP_LineCTL_Tx 0x0080 /* Enable transmitter */
142#define PP_LineCTL_AUIonly 0x0100 /* AUI interface only */
143#define PP_LineCTL_AutoAUI10BT 0x0200 /* Autodetect AUI or 10BaseT interface */
144#define PP_LineCTL_ModBackoffE 0x0800 /* Enable modified backoff algorithm */
145#define PP_LineCTL_PolarityDis 0x1000 /* Disable Rx polarity autodetect */
146#define PP_LineCTL_2partDefDis 0x2000 /* Disable two-part defferal */
147#define PP_LineCTL_LoRxSquelch 0x4000 /* Reduce receiver squelch threshold */
148
149#define PP_SelfCTL 0x0114 /* Chip self control */
150#define PP_SelfCTL_Reset 0x0040 /* Self-clearing reset */
151#define PP_SelfCTL_SWSuspend 0x0100 /* Initiate suspend mode */
152#define PP_SelfCTL_HWSleepE 0x0200 /* Enable SLEEP input */
153#define PP_SelfCTL_HWStandbyE 0x0400 /* Enable standby mode */
154#define PP_SelfCTL_HC0E 0x1000 /* use HCB0 for LINK LED */
155#define PP_SelfCTL_HC1E 0x2000 /* use HCB1 for BSTATUS LED */
156#define PP_SelfCTL_HCB0 0x4000 /* control LINK LED if HC0E set */
157#define PP_SelfCTL_HCB1 0x8000 /* control BSTATUS LED if HC1E set */
158
159#define PP_BusCTL 0x0116 /* Bus control */
160#define PP_BusCTL_ResetRxDMA 0x0040 /* Reset RxDMA pointer */
161#define PP_BusCTL_DMAextend 0x0100 /* Extend DMA cycle */
162#define PP_BusCTL_UseSA 0x0200 /* Assert MEMCS16 on address decode */
163#define PP_BusCTL_MemoryE 0x0400 /* Enable memory mode */
164#define PP_BusCTL_DMAburst 0x0800 /* Limit DMA access burst */
165#define PP_BusCTL_IOCHRDYE 0x1000 /* Set IOCHRDY high impedence */
166#define PP_BusCTL_RxDMAsize 0x2000 /* Set DMA buffer size 64KB */
167#define PP_BusCTL_EnableIRQ 0x8000 /* Generate interrupt on interrupt event */
168
169#define PP_TestCTL 0x0118 /* Test control */
170#define PP_TestCTL_DisableLT 0x0080 /* Disable link status */
171#define PP_TestCTL_ENDECloop 0x0200 /* Internal loopback */
172#define PP_TestCTL_AUIloop 0x0400 /* AUI loopback */
173#define PP_TestCTL_DisBackoff 0x0800 /* Disable backoff algorithm */
174#define PP_TestCTL_FDX 0x4000 /* Enable full duplex mode */
175
176#define PP_ISQ 0x0120 /* Interrupt Status Queue */
177
178#define PP_RER 0x0124 /* Receive event */
179#define PP_RER_IAHash 0x0040 /* Frame hash match */
180#define PP_RER_Dribble 0x0080 /* Frame had 1-7 extra bits after last byte */
181#define PP_RER_RxOK 0x0100 /* Frame received with no errors */
182#define PP_RER_Hashed 0x0200 /* Frame address hashed OK */
183#define PP_RER_IA 0x0400 /* Frame address matched IA */
184#define PP_RER_Broadcast 0x0800 /* Broadcast frame */
185#define PP_RER_CRC 0x1000 /* Frame had CRC error */
186#define PP_RER_RUNT 0x2000 /* Runt frame */
187#define PP_RER_EXTRA 0x4000 /* Frame was too long */
188
189#define PP_TER 0x0128 /* Transmit event */
190#define PP_TER_CRS 0x0040 /* Carrier lost */
191#define PP_TER_SQE 0x0080 /* Signal Quality Error */
192#define PP_TER_TxOK 0x0100 /* Packet sent without error */
193#define PP_TER_Late 0x0200 /* Out of window */
194#define PP_TER_Jabber 0x0400 /* Stuck transmit? */
195#define PP_TER_NumCollisions 0x7800 /* Number of collisions */
196#define PP_TER_16Collisions 0x8000 /* > 16 collisions */
197
198#define PP_BER 0x012C /* Buffer event */
199#define PP_BER_SWint 0x0040 /* Software interrupt */
200#define PP_BER_RxDMAFrame 0x0080 /* Received framed DMAed */
201#define PP_BER_Rdy4Tx 0x0100 /* Ready for transmission */
202#define PP_BER_TxUnderrun 0x0200 /* Transmit underrun */
203#define PP_BER_RxMiss 0x0400 /* Received frame missed */
204#define PP_BER_Rx128 0x0800 /* 128 bytes received */
205#define PP_BER_RxDest 0x8000 /* Received framed passed address filter */
206
207#define PP_RxMiss 0x0130 /* Receiver miss counter */
208
209#define PP_TxCol 0x0132 /* Transmit collision counter */
210
211#define PP_LineSTAT 0x0134 /* Line status */
212#define PP_LineSTAT_LinkOK 0x0080 /* Line is connected and working */
213#define PP_LineSTAT_AUI 0x0100 /* Connected via AUI */
214#define PP_LineSTAT_10BT 0x0200 /* Connected via twisted pair */
215#define PP_LineSTAT_Polarity 0x1000 /* Line polarity OK (10BT only) */
216#define PP_LineSTAT_CRS 0x4000 /* Frame being received */
217
218#define PP_SelfSTAT 0x0136 /* Chip self status */
219#define PP_SelfSTAT_33VActive 0x0040 /* supply voltage is 3.3V */
220#define PP_SelfSTAT_InitD 0x0080 /* Chip initialization complete */
221#define PP_SelfSTAT_SIBSY 0x0100 /* EEPROM is busy */
222#define PP_SelfSTAT_EEPROM 0x0200 /* EEPROM present */
223#define PP_SelfSTAT_EEPROM_OK 0x0400 /* EEPROM checks out */
224#define PP_SelfSTAT_ELPresent 0x0800 /* External address latch logic available */
225#define PP_SelfSTAT_EEsize 0x1000 /* Size of EEPROM */
226
227#define PP_BusSTAT 0x0138 /* Bus status */
228#define PP_BusSTAT_TxBid 0x0080 /* Tx error */
229#define PP_BusSTAT_TxRDY 0x0100 /* Ready for Tx data */
230
231#define PP_TDR 0x013C /* AUI Time Domain Reflectometer */
232
233/* initiate transmit registers */
234
235#define PP_TxCommand 0x0144 /* Tx Command */
236#define PP_TxLength 0x0146 /* Tx Length */
237
238
239/* address filter registers */
240
241#define PP_LAF 0x0150 /* Logical address filter (6 bytes) */
242#define PP_IA 0x0158 /* Individual address (MAC) */
243
244/* EEPROM Kram */
245#define SI_BUSY 0x0100
wdenkfe8c2802002-11-03 00:38:21 +0000246#define PP_EECMD 0x0040 /* NVR Interface Command register */
247#define PP_EEData 0x0042 /* NVR Interface Data Register */
248#define EEPROM_WRITE_EN 0x00F0
249#define EEPROM_WRITE_DIS 0x0000
250#define EEPROM_WRITE_CMD 0x0100
251#define EEPROM_READ_CMD 0x0200
wdenk1cb8e982003-03-06 21:55:29 +0000252#define EEPROM_ERASE_CMD 0x0300
wdenkfe8c2802002-11-03 00:38:21 +0000253
wdenk1cb8e982003-03-06 21:55:29 +0000254extern int cs8900_e2prom_read(uchar, ushort *);
wdenk06d01db2003-03-14 20:47:52 +0000255extern int cs8900_e2prom_write(uchar, ushort);
wdenkfe8c2802002-11-03 00:38:21 +0000256
257#endif /* CONFIG_DRIVER_CS8900 */