| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 1 | /* |
| 2 | * Copyright 2013-2015 Arcturus Networks, Inc. |
| 3 | * http://www.arcturusnetworks.com/products/ucp1020/ |
| 4 | * based on include/configs/p1_p2_rdb_pc.h |
| 5 | * original copyright follows: |
| 6 | * Copyright 2009-2011 Freescale Semiconductor, Inc. |
| 7 | * |
| 8 | * SPDX-License-Identifier: GPL-2.0+ |
| 9 | */ |
| 10 | |
| 11 | /* |
| 12 | * QorIQ uCP1020-xx boards configuration file |
| 13 | */ |
| 14 | #ifndef __CONFIG_H |
| 15 | #define __CONFIG_H |
| 16 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 17 | #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */ |
| 18 | #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */ |
| 19 | #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ |
| 20 | #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ |
| 21 | #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ |
| 22 | #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ |
| 23 | |
| 24 | #if defined(CONFIG_TARTGET_UCP1020T1) |
| 25 | |
| 26 | #define CONFIG_UCP1020_REV_1_3 |
| 27 | |
| 28 | #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1" |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 29 | |
| 30 | #define CONFIG_TSEC_ENET |
| 31 | #define CONFIG_TSEC1 |
| 32 | #define CONFIG_TSEC3 |
| 33 | #define CONFIG_HAS_ETH0 |
| 34 | #define CONFIG_HAS_ETH1 |
| 35 | #define CONFIG_ETHADDR 00:19:D3:FF:FF:FF |
| 36 | #define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE |
| 37 | #define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD |
| 38 | #define CONFIG_IPADDR 10.80.41.229 |
| 39 | #define CONFIG_SERVERIP 10.80.41.227 |
| 40 | #define CONFIG_NETMASK 255.255.252.0 |
| 41 | #define CONFIG_ETHPRIME "eTSEC3" |
| 42 | |
| 43 | #ifndef CONFIG_SPI_FLASH |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 44 | #endif |
| 45 | #define CONFIG_SYS_REDUNDAND_ENVIRONMENT |
| 46 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 47 | #define CONFIG_SYS_L2_SIZE (256 << 10) |
| 48 | |
| 49 | #define CONFIG_LAST_STAGE_INIT |
| 50 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 51 | #endif |
| 52 | |
| 53 | #if defined(CONFIG_TARGET_UCP1020) |
| 54 | |
| 55 | #define CONFIG_UCP1020 |
| 56 | #define CONFIG_UCP1020_REV_1_3 |
| 57 | |
| 58 | #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR" |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 59 | |
| 60 | #define CONFIG_TSEC_ENET |
| 61 | #define CONFIG_TSEC1 |
| 62 | #define CONFIG_TSEC2 |
| 63 | #define CONFIG_TSEC3 |
| 64 | #define CONFIG_HAS_ETH0 |
| 65 | #define CONFIG_HAS_ETH1 |
| 66 | #define CONFIG_HAS_ETH2 |
| 67 | #define CONFIG_ETHADDR 00:06:3B:FF:FF:FF |
| 68 | #define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE |
| 69 | #define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD |
| 70 | #define CONFIG_IPADDR 192.168.1.81 |
| 71 | #define CONFIG_IPADDR1 192.168.1.82 |
| 72 | #define CONFIG_IPADDR2 192.168.1.83 |
| 73 | #define CONFIG_SERVERIP 192.168.1.80 |
| 74 | #define CONFIG_GATEWAYIP 102.168.1.1 |
| 75 | #define CONFIG_NETMASK 255.255.255.0 |
| 76 | #define CONFIG_ETHPRIME "eTSEC1" |
| 77 | |
| 78 | #ifndef CONFIG_SPI_FLASH |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 79 | #endif |
| 80 | #define CONFIG_SYS_REDUNDAND_ENVIRONMENT |
| 81 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 82 | #define CONFIG_SYS_L2_SIZE (256 << 10) |
| 83 | |
| 84 | #define CONFIG_LAST_STAGE_INIT |
| 85 | |
| 86 | #endif |
| 87 | |
| 88 | #ifdef CONFIG_SDCARD |
| 89 | #define CONFIG_RAMBOOT_SDCARD |
| 90 | #define CONFIG_SYS_RAMBOOT |
| 91 | #define CONFIG_SYS_EXTRA_ENV_RELOC |
| 92 | #define CONFIG_SYS_TEXT_BASE 0x11000000 |
| 93 | #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc |
| 94 | #endif |
| 95 | |
| 96 | #ifdef CONFIG_SPIFLASH |
| 97 | #define CONFIG_RAMBOOT_SPIFLASH |
| 98 | #define CONFIG_SYS_RAMBOOT |
| 99 | #define CONFIG_SYS_EXTRA_ENV_RELOC |
| 100 | #define CONFIG_SYS_TEXT_BASE 0x11000000 |
| 101 | #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc |
| 102 | #endif |
| 103 | |
| 104 | #ifndef CONFIG_SYS_TEXT_BASE |
| 105 | #define CONFIG_SYS_TEXT_BASE 0xeff80000 |
| 106 | #endif |
| 107 | #define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000 |
| 108 | |
| 109 | #ifndef CONFIG_RESET_VECTOR_ADDRESS |
| 110 | #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc |
| 111 | #endif |
| 112 | |
| 113 | #ifndef CONFIG_SYS_MONITOR_BASE |
| 114 | #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| 115 | #endif |
| 116 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 117 | #define CONFIG_MP |
| 118 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 119 | #define CONFIG_ENV_OVERWRITE |
| 120 | |
| 121 | #define CONFIG_CMD_SATA |
| 122 | #define CONFIG_SATA_SIL |
| 123 | #define CONFIG_SYS_SATA_MAX_DEVICE 2 |
| 124 | #define CONFIG_LIBATA |
| 125 | #define CONFIG_LBA48 |
| 126 | |
| 127 | #define CONFIG_SYS_CLK_FREQ 66666666 |
| 128 | #define CONFIG_DDR_CLK_FREQ 66666666 |
| 129 | |
| 130 | #define CONFIG_HWCONFIG |
| 131 | |
| 132 | #define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */ |
| 133 | #define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */ |
| 134 | #define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */ |
| 135 | /* |
| 136 | * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details). |
| 137 | * there will be one entry in this array for each two (dummy) sensors in |
| 138 | * CONFIG_DTT_SENSORS. |
| 139 | * |
| 140 | * For uCP1020 module: |
| 141 | * - only one ADM1021/NCT72 |
| 142 | * - i2c addr 0x41 |
| 143 | * - conversion rate 0x02 = 0.25 conversions/second |
| 144 | * - ALERT output disabled |
| 145 | * - local temp sensor enabled, min set to 0 deg, max set to 85 deg |
| 146 | * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg |
| 147 | */ |
| 148 | #define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \ |
| 149 | 0x02, 0, 1, 0, 85, 1, 0, 85} } |
| 150 | |
| 151 | #define CONFIG_CMD_DTT |
| 152 | |
| 153 | /* |
| 154 | * These can be toggled for performance analysis, otherwise use default. |
| 155 | */ |
| 156 | #define CONFIG_L2_CACHE |
| 157 | #define CONFIG_BTB |
| 158 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 159 | #define CONFIG_ENABLE_36BIT_PHYS |
| 160 | |
| 161 | #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ |
| 162 | #define CONFIG_SYS_MEMTEST_END 0x1fffffff |
| 163 | #define CONFIG_PANIC_HANG /* do not reset board on panic */ |
| 164 | |
| 165 | #define CONFIG_SYS_CCSRBAR 0xffe00000 |
| 166 | #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR |
| 167 | |
| 168 | /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k |
| 169 | SPL code*/ |
| 170 | #ifdef CONFIG_SPL_BUILD |
| 171 | #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE |
| 172 | #endif |
| 173 | |
| 174 | /* DDR Setup */ |
| 175 | #define CONFIG_DDR_ECC_ENABLE |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 176 | #ifndef CONFIG_DDR_ECC_ENABLE |
| 177 | #define CONFIG_SYS_DDR_RAW_TIMING |
| 178 | #define CONFIG_DDR_SPD |
| 179 | #endif |
| 180 | #define CONFIG_SYS_SPD_BUS_NUM 1 |
| 181 | #undef CONFIG_FSL_DDR_INTERACTIVE |
| 182 | |
| 183 | #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M |
| 184 | #define CONFIG_CHIP_SELECTS_PER_CTRL 1 |
| 185 | #define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) |
| 186 | #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 |
| 187 | #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| 188 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 189 | #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| 190 | |
| 191 | /* Default settings for DDR3 */ |
| 192 | #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f |
| 193 | #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 |
| 194 | #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 |
| 195 | #define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f |
| 196 | #define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302 |
| 197 | #define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 |
| 198 | |
| 199 | #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef |
| 200 | #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 |
| 201 | #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 |
| 202 | #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 |
| 203 | |
| 204 | #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 |
| 205 | #define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608 |
| 206 | #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 |
| 207 | #define CONFIG_SYS_DDR_RCW_1 0x00000000 |
| 208 | #define CONFIG_SYS_DDR_RCW_2 0x00000000 |
| 209 | #ifdef CONFIG_DDR_ECC_ENABLE |
| 210 | #define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */ |
| 211 | #else |
| 212 | #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ |
| 213 | #endif |
| 214 | #define CONFIG_SYS_DDR_CONTROL_2 0x04401050 |
| 215 | #define CONFIG_SYS_DDR_TIMING_4 0x00220001 |
| 216 | #define CONFIG_SYS_DDR_TIMING_5 0x03402400 |
| 217 | |
| 218 | #define CONFIG_SYS_DDR_TIMING_3 0x00020000 |
| 219 | #define CONFIG_SYS_DDR_TIMING_0 0x00330004 |
| 220 | #define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846 |
| 221 | #define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF |
| 222 | #define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 |
| 223 | #define CONFIG_SYS_DDR_MODE_1 0x40461520 |
| 224 | #define CONFIG_SYS_DDR_MODE_2 0x8000c000 |
| 225 | #define CONFIG_SYS_DDR_INTERVAL 0x0C300000 |
| 226 | |
| 227 | #undef CONFIG_CLOCKS_IN_MHZ |
| 228 | |
| 229 | /* |
| 230 | * Memory map |
| 231 | * |
| 232 | * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable |
| 233 | * 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2) |
| 234 | * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1 |
| 235 | * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable |
| 236 | * (early boot only) |
| 237 | * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable |
| 238 | * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable |
| 239 | * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable |
| 240 | */ |
| 241 | |
| 242 | /* |
| 243 | * Local Bus Definitions |
| 244 | */ |
| 245 | #define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ |
| 246 | #define CONFIG_SYS_FLASH_BASE 0xec000000 |
| 247 | |
| 248 | #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE |
| 249 | |
| 250 | #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ |
| 251 | | BR_PS_16 | BR_V) |
| 252 | |
| 253 | #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 |
| 254 | |
| 255 | #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} |
| 256 | #define CONFIG_SYS_FLASH_QUIET_TEST |
| 257 | #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| 258 | |
| 259 | #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| 260 | |
| 261 | #undef CONFIG_SYS_FLASH_CHECKSUM |
| 262 | #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| 263 | #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| 264 | |
| 265 | #define CONFIG_FLASH_CFI_DRIVER |
| 266 | #define CONFIG_SYS_FLASH_CFI |
| 267 | #define CONFIG_SYS_FLASH_EMPTY_INFO |
| 268 | #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE |
| 269 | |
| 270 | #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ |
| 271 | |
| 272 | #define CONFIG_SYS_INIT_RAM_LOCK |
| 273 | #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ |
| 274 | /* Initial L1 address */ |
| 275 | #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR |
| 276 | #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 |
| 277 | #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS |
| 278 | /* Size of used area in RAM */ |
| 279 | #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 |
| 280 | |
| 281 | #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ |
| 282 | GENERATED_GBL_DATA_SIZE) |
| 283 | #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| 284 | |
| 285 | #define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */ |
| 286 | #define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */ |
| 287 | |
| 288 | #define CONFIG_SYS_PMC_BASE 0xff980000 |
| 289 | #define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE |
| 290 | #define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \ |
| 291 | BR_PS_8 | BR_V) |
| 292 | #define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ |
| 293 | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \ |
| 294 | OR_GPCM_EAD) |
| 295 | |
| 296 | #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ |
| 297 | #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ |
| 298 | #ifdef CONFIG_NAND_FSL_ELBC |
| 299 | #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */ |
| 300 | #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ |
| 301 | #endif |
| 302 | |
| 303 | /* Serial Port - controlled on board with jumper J8 |
| 304 | * open - index 2 |
| 305 | * shorted - index 1 |
| 306 | */ |
| 307 | #define CONFIG_CONS_INDEX 1 |
| 308 | #undef CONFIG_SERIAL_SOFTWARE_FIFO |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 309 | #define CONFIG_SYS_NS16550_SERIAL |
| 310 | #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| 311 | #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| 312 | #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL) |
| 313 | #define CONFIG_NS16550_MIN_FUNCTIONS |
| 314 | #endif |
| 315 | |
| 316 | #define CONFIG_SYS_BAUDRATE_TABLE \ |
| 317 | {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| 318 | |
| 319 | #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) |
| 320 | #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) |
| 321 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 322 | /* I2C */ |
| 323 | #define CONFIG_SYS_I2C |
| 324 | #define CONFIG_SYS_I2C_FSL |
| 325 | #define CONFIG_SYS_FSL_I2C_SPEED 400000 |
| 326 | #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| 327 | #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 |
| 328 | #define CONFIG_SYS_FSL_I2C2_SPEED 400000 |
| 329 | #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F |
| 330 | #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 |
| 331 | #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } |
| 332 | #define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */ |
| 333 | |
| 334 | #define CONFIG_RTC_DS1337 |
| 335 | #define CONFIG_SYS_RTC_DS1337_NOOSC |
| 336 | #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| 337 | #define CONFIG_SYS_I2C_PCA9557_ADDR 0x18 |
| 338 | #define CONFIG_SYS_I2C_NCT72_ADDR 0x4C |
| 339 | #define CONFIG_SYS_I2C_IDT6V49205B 0x69 |
| 340 | |
| 341 | /* |
| 342 | * eSPI - Enhanced SPI |
| 343 | */ |
| 344 | #define CONFIG_HARD_SPI |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 345 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 346 | #define CONFIG_SF_DEFAULT_SPEED 10000000 |
| 347 | #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 |
| 348 | |
| 349 | #if defined(CONFIG_PCI) |
| 350 | /* |
| 351 | * General PCI |
| 352 | * Memory space is mapped 1-1, but I/O space must start from 0. |
| 353 | */ |
| 354 | |
| 355 | /* controller 2, direct to uli, tgtid 2, Base address 9000 */ |
| 356 | #define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9" |
| 357 | #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 |
| 358 | #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 |
| 359 | #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 |
| 360 | #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ |
| 361 | #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 |
| 362 | #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 |
| 363 | #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 |
| 364 | #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ |
| 365 | |
| 366 | /* controller 1, Slot 2, tgtid 1, Base address a000 */ |
| 367 | #define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10" |
| 368 | #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 |
| 369 | #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 |
| 370 | #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 |
| 371 | #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ |
| 372 | #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 |
| 373 | #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 |
| 374 | #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 |
| 375 | #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ |
| 376 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 377 | #define CONFIG_CMD_PCI |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 378 | |
| 379 | #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 380 | #endif /* CONFIG_PCI */ |
| 381 | |
| 382 | /* |
| 383 | * Environment |
| 384 | */ |
| 385 | #ifdef CONFIG_ENV_FIT_UCBOOT |
| 386 | |
| 387 | #define CONFIG_ENV_IS_IN_FLASH |
| 388 | #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000) |
| 389 | #define CONFIG_ENV_SIZE 0x20000 |
| 390 | #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ |
| 391 | |
| 392 | #else |
| 393 | |
| 394 | #define CONFIG_ENV_SPI_BUS 0 |
| 395 | #define CONFIG_ENV_SPI_CS 0 |
| 396 | #define CONFIG_ENV_SPI_MAX_HZ 10000000 |
| 397 | #define CONFIG_ENV_SPI_MODE 0 |
| 398 | |
| 399 | #ifdef CONFIG_RAMBOOT_SPIFLASH |
| 400 | |
| 401 | #define CONFIG_ENV_IS_IN_SPI_FLASH |
| 402 | #define CONFIG_ENV_SIZE 0x3000 /* 12KB */ |
| 403 | #define CONFIG_ENV_OFFSET 0x2000 /* 8KB */ |
| 404 | #define CONFIG_ENV_SECT_SIZE 0x1000 |
| 405 | |
| 406 | #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) |
| 407 | /* Address and size of Redundant Environment Sector */ |
| 408 | #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) |
| 409 | #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE |
| 410 | #endif |
| 411 | |
| 412 | #elif defined(CONFIG_RAMBOOT_SDCARD) |
| 413 | #define CONFIG_ENV_IS_IN_MMC |
| 414 | #define CONFIG_FSL_FIXED_MMC_LOCATION |
| 415 | #define CONFIG_ENV_SIZE 0x2000 |
| 416 | #define CONFIG_SYS_MMC_ENV_DEV 0 |
| 417 | |
| 418 | #elif defined(CONFIG_SYS_RAMBOOT) |
| 419 | #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ |
| 420 | #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) |
| 421 | #define CONFIG_ENV_SIZE 0x2000 |
| 422 | |
| 423 | #else |
| 424 | #define CONFIG_ENV_IS_IN_FLASH |
| 425 | #define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE) |
| 426 | #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ |
| 427 | #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE |
| 428 | #define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000) |
| 429 | #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) |
| 430 | /* Address and size of Redundant Environment Sector */ |
| 431 | #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) |
| 432 | #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE |
| 433 | #endif |
| 434 | |
| 435 | #endif |
| 436 | |
| 437 | #endif /* CONFIG_ENV_FIT_UCBOOT */ |
| 438 | |
| 439 | #define CONFIG_LOADS_ECHO /* echo on for serial download */ |
| 440 | #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ |
| 441 | |
| 442 | /* |
| 443 | * Command line configuration. |
| 444 | */ |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 445 | #define CONFIG_CMD_IRQ |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 446 | #define CONFIG_CMD_IRQ |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 447 | #define CONFIG_CMD_REGINFO |
| 448 | #define CONFIG_CMD_ERRATA |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 449 | |
| 450 | /* |
| 451 | * USB |
| 452 | */ |
| 453 | #define CONFIG_HAS_FSL_DR_USB |
| 454 | |
| 455 | #if defined(CONFIG_HAS_FSL_DR_USB) |
| 456 | #define CONFIG_USB_EHCI |
| 457 | |
| 458 | #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 |
| 459 | |
| 460 | #ifdef CONFIG_USB_EHCI |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 461 | #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| 462 | #define CONFIG_USB_EHCI_FSL |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 463 | #endif |
| 464 | #endif |
| 465 | |
| 466 | #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| 467 | |
| 468 | #ifdef CONFIG_MMC |
| 469 | #define CONFIG_FSL_ESDHC |
| 470 | #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 471 | #define CONFIG_MMC_SPI |
| 472 | #define CONFIG_CMD_MMC_SPI |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 473 | #endif |
| 474 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 475 | /* Misc Extra Settings */ |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 476 | #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| 477 | |
| 478 | /* |
| 479 | * Miscellaneous configurable options |
| 480 | */ |
| 481 | #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| 482 | #define CONFIG_CMDLINE_EDITING /* Command-line editing */ |
| 483 | #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 484 | #if defined(CONFIG_CMD_KGDB) |
| 485 | #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| 486 | #else |
| 487 | #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| 488 | #endif |
| 489 | #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| 490 | /* Print Buffer Size */ |
| 491 | #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| 492 | #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ |
| 493 | #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */ |
| 494 | |
| 495 | /* |
| 496 | * For booting Linux, the board info and command line data |
| 497 | * have to be in the first 64 MB of memory, since this is |
| 498 | * the maximum mapped by the Linux kernel during initialization. |
| 499 | */ |
| 500 | #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ |
| 501 | #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ |
| 502 | |
| 503 | #if defined(CONFIG_CMD_KGDB) |
| 504 | #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| 505 | #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| 506 | #endif |
| 507 | |
| 508 | /* |
| 509 | * Environment Configuration |
| 510 | */ |
| 511 | |
| 512 | #if defined(CONFIG_TSEC_ENET) |
| 513 | |
| 514 | #if defined(CONFIG_UCP1020_REV_1_2) |
| 515 | #define CONFIG_PHY_MICREL_KSZ9021 |
| 516 | #elif defined(CONFIG_UCP1020_REV_1_3) |
| 517 | #define CONFIG_PHY_MICREL_KSZ9031 |
| 518 | #else |
| 519 | #error "UCP1020 module revision is not defined !!!" |
| 520 | #endif |
| 521 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 522 | #define CONFIG_BOOTP_SERVERIP |
| 523 | |
| 524 | #define CONFIG_MII /* MII PHY management */ |
| 525 | #define CONFIG_TSEC1_NAME "eTSEC1" |
| 526 | #define CONFIG_TSEC2_NAME "eTSEC2" |
| 527 | #define CONFIG_TSEC3_NAME "eTSEC3" |
| 528 | |
| 529 | #define TSEC1_PHY_ADDR 4 |
| 530 | #define TSEC2_PHY_ADDR 0 |
| 531 | #define TSEC2_PHY_ADDR_SGMII 0x00 |
| 532 | #define TSEC3_PHY_ADDR 6 |
| 533 | |
| 534 | #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| 535 | #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| 536 | #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| 537 | |
| 538 | #define TSEC1_PHYIDX 0 |
| 539 | #define TSEC2_PHYIDX 0 |
| 540 | #define TSEC3_PHYIDX 0 |
| 541 | |
| 542 | #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ |
| 543 | |
| 544 | #endif |
| 545 | |
| 546 | #define CONFIG_HOSTNAME UCP1020 |
| 547 | #define CONFIG_ROOTPATH "/opt/nfsroot" |
| 548 | #define CONFIG_BOOTFILE "uImage" |
| 549 | #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ |
| 550 | |
| 551 | /* default location for tftp and bootm */ |
| 552 | #define CONFIG_LOADADDR 1000000 |
| 553 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 554 | #define CONFIG_BOOTARGS /* the boot command will set bootargs */ |
| 555 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 556 | #if defined(CONFIG_DONGLE) |
| 557 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 558 | #define CONFIG_EXTRA_ENV_SETTINGS \ |
| 559 | "bootcmd=run prog_spi_mbrbootcramfs\0" \ |
| 560 | "bootfile=uImage\0" \ |
| 561 | "consoledev=ttyS0\0" \ |
| 562 | "cramfsfile=image.cramfs\0" \ |
| 563 | "dtbaddr=0x00c00000\0" \ |
| 564 | "dtbfile=image.dtb\0" \ |
| 565 | "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ |
| 566 | "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ |
| 567 | "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ |
| 568 | "fileaddr=0x01000000\0" \ |
| 569 | "filesize=0x00080000\0" \ |
| 570 | "flashmbr=sf probe 0; " \ |
| 571 | "tftp $loadaddr $mbr; " \ |
| 572 | "sf erase $mbr_offset +$filesize; " \ |
| 573 | "sf write $loadaddr $mbr_offset $filesize\0" \ |
| 574 | "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ |
| 575 | "protect off $nor_recoveryaddr +$filesize; " \ |
| 576 | "erase $nor_recoveryaddr +$filesize; " \ |
| 577 | "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ |
| 578 | "protect on $nor_recoveryaddr +$filesize\0 " \ |
| 579 | "flashuboot=tftp $ubootaddr $ubootfile; " \ |
| 580 | "protect off $nor_ubootaddr +$filesize; " \ |
| 581 | "erase $nor_ubootaddr +$filesize; " \ |
| 582 | "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ |
| 583 | "protect on $nor_ubootaddr +$filesize\0 " \ |
| 584 | "flashworking=tftp $workingaddr $cramfsfile; " \ |
| 585 | "protect off $nor_workingaddr +$filesize; " \ |
| 586 | "erase $nor_workingaddr +$filesize; " \ |
| 587 | "cp.b $workingaddr $nor_workingaddr $filesize; " \ |
| 588 | "protect on $nor_workingaddr +$filesize\0 " \ |
| 589 | "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ |
| 590 | "kerneladdr=0x01100000\0" \ |
| 591 | "kernelfile=uImage\0" \ |
| 592 | "loadaddr=0x01000000\0" \ |
| 593 | "mbr=uCP1020d.mbr\0" \ |
| 594 | "mbr_offset=0x00000000\0" \ |
| 595 | "mmbr=uCP1020Quiet.mbr\0" \ |
| 596 | "mmcpart=0:2\0" \ |
| 597 | "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ |
| 598 | "mmc erase 1 1; " \ |
| 599 | "mmc write $loadaddr 1 1\0" \ |
| 600 | "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \ |
| 601 | "mmc erase 0x40 0x400; " \ |
| 602 | "mmc write $loadaddr 0x40 0x400\0" \ |
| 603 | "netdev=eth0\0" \ |
| 604 | "nor_recoveryaddr=0xEC0A0000\0" \ |
| 605 | "nor_ubootaddr=0xEFF80000\0" \ |
| 606 | "nor_workingaddr=0xECFA0000\0" \ |
| 607 | "norbootrecovery=setenv bootargs $recoverybootargs" \ |
| 608 | " console=$consoledev,$baudrate $othbootargs; " \ |
| 609 | "run norloadrecovery; " \ |
| 610 | "bootm $kerneladdr - $dtbaddr\0" \ |
| 611 | "norbootworking=setenv bootargs $workingbootargs" \ |
| 612 | " console=$consoledev,$baudrate $othbootargs; " \ |
| 613 | "run norloadworking; " \ |
| 614 | "bootm $kerneladdr - $dtbaddr\0" \ |
| 615 | "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ |
| 616 | "setenv cramfsaddr $nor_recoveryaddr; " \ |
| 617 | "cramfsload $dtbaddr $dtbfile; " \ |
| 618 | "cramfsload $kerneladdr $kernelfile\0" \ |
| 619 | "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ |
| 620 | "setenv cramfsaddr $nor_workingaddr; " \ |
| 621 | "cramfsload $dtbaddr $dtbfile; " \ |
| 622 | "cramfsload $kerneladdr $kernelfile\0" \ |
| 623 | "prog_spi_mbr=run spi__mbr\0" \ |
| 624 | "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \ |
| 625 | "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \ |
| 626 | "run spi__cramfs\0" \ |
| 627 | "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ |
| 628 | " console=$consoledev,$baudrate $othbootargs; " \ |
| 629 | "tftp $rootfsaddr $rootfsfile; " \ |
| 630 | "tftp $loadaddr $kernelfile; " \ |
| 631 | "tftp $dtbaddr $dtbfile; " \ |
| 632 | "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ |
| 633 | "ramdisk_size=120000\0" \ |
| 634 | "ramdiskfile=rootfs.ext2.gz.uboot\0" \ |
| 635 | "recoveryaddr=0x02F00000\0" \ |
| 636 | "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ |
| 637 | "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ |
| 638 | "mw.l 0xffe0f008 0x00400000\0" \ |
| 639 | "rootfsaddr=0x02F00000\0" \ |
| 640 | "rootfsfile=rootfs.ext2.gz.uboot\0" \ |
| 641 | "rootpath=/opt/nfsroot\0" \ |
| 642 | "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ |
| 643 | "protect off 0xeC000000 +$filesize; " \ |
| 644 | "erase 0xEC000000 +$filesize; " \ |
| 645 | "cp.b $loadaddr 0xEC000000 $filesize; " \ |
| 646 | "cmp.b $loadaddr 0xEC000000 $filesize; " \ |
| 647 | "protect on 0xeC000000 +$filesize\0" \ |
| 648 | "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ |
| 649 | "protect off 0xeFF80000 +$filesize; " \ |
| 650 | "erase 0xEFF80000 +$filesize; " \ |
| 651 | "cp.b $loadaddr 0xEFF80000 $filesize; " \ |
| 652 | "cmp.b $loadaddr 0xEFF80000 $filesize; " \ |
| 653 | "protect on 0xeFF80000 +$filesize\0" \ |
| 654 | "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \ |
| 655 | "sf probe 0; sf erase 0x8000 +$filesize; " \ |
| 656 | "sf write $loadaddr 0x8000 $filesize\0" \ |
| 657 | "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \ |
| 658 | "protect off 0xec0a0000 +$filesize; " \ |
| 659 | "erase 0xeC0A0000 +$filesize; " \ |
| 660 | "cp.b $loadaddr 0xeC0A0000 $filesize; " \ |
| 661 | "protect on 0xec0a0000 +$filesize\0" \ |
| 662 | "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ |
| 663 | "sf probe 1; sf erase 0 +$filesize; " \ |
| 664 | "sf write $loadaddr 0 $filesize\0" \ |
| 665 | "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ |
| 666 | "sf probe 0; sf erase 0 +$filesize; " \ |
| 667 | "sf write $loadaddr 0 $filesize\0" \ |
| 668 | "tftpflash=tftpboot $loadaddr $uboot; " \ |
| 669 | "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| 670 | "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| 671 | "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ |
| 672 | "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| 673 | "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ |
| 674 | "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ |
| 675 | "ubootaddr=0x01000000\0" \ |
| 676 | "ubootfile=u-boot.bin\0" \ |
| 677 | "ubootd=u-boot4dongle.bin\0" \ |
| 678 | "upgrade=run flashworking\0" \ |
| 679 | "usb_phy_type=ulpi\0 " \ |
| 680 | "workingaddr=0x02F00000\0" \ |
| 681 | "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" |
| 682 | |
| 683 | #else |
| 684 | |
| 685 | #if defined(CONFIG_UCP1020T1) |
| 686 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 687 | #define CONFIG_EXTRA_ENV_SETTINGS \ |
| 688 | "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \ |
| 689 | "bootfile=uImage\0" \ |
| 690 | "consoledev=ttyS0\0" \ |
| 691 | "cramfsfile=image.cramfs\0" \ |
| 692 | "dtbaddr=0x00c00000\0" \ |
| 693 | "dtbfile=image.dtb\0" \ |
| 694 | "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ |
| 695 | "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ |
| 696 | "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ |
| 697 | "fileaddr=0x01000000\0" \ |
| 698 | "filesize=0x00080000\0" \ |
| 699 | "flashmbr=sf probe 0; " \ |
| 700 | "tftp $loadaddr $mbr; " \ |
| 701 | "sf erase $mbr_offset +$filesize; " \ |
| 702 | "sf write $loadaddr $mbr_offset $filesize\0" \ |
| 703 | "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ |
| 704 | "protect off $nor_recoveryaddr +$filesize; " \ |
| 705 | "erase $nor_recoveryaddr +$filesize; " \ |
| 706 | "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ |
| 707 | "protect on $nor_recoveryaddr +$filesize\0 " \ |
| 708 | "flashuboot=tftp $ubootaddr $ubootfile; " \ |
| 709 | "protect off $nor_ubootaddr +$filesize; " \ |
| 710 | "erase $nor_ubootaddr +$filesize; " \ |
| 711 | "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ |
| 712 | "protect on $nor_ubootaddr +$filesize\0 " \ |
| 713 | "flashworking=tftp $workingaddr $cramfsfile; " \ |
| 714 | "protect off $nor_workingaddr +$filesize; " \ |
| 715 | "erase $nor_workingaddr +$filesize; " \ |
| 716 | "cp.b $workingaddr $nor_workingaddr $filesize; " \ |
| 717 | "protect on $nor_workingaddr +$filesize\0 " \ |
| 718 | "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ |
| 719 | "kerneladdr=0x01100000\0" \ |
| 720 | "kernelfile=uImage\0" \ |
| 721 | "loadaddr=0x01000000\0" \ |
| 722 | "mbr=uCP1020.mbr\0" \ |
| 723 | "mbr_offset=0x00000000\0" \ |
| 724 | "netdev=eth0\0" \ |
| 725 | "nor_recoveryaddr=0xEC0A0000\0" \ |
| 726 | "nor_ubootaddr=0xEFF80000\0" \ |
| 727 | "nor_workingaddr=0xECFA0000\0" \ |
| 728 | "norbootrecovery=setenv bootargs $recoverybootargs" \ |
| 729 | " console=$consoledev,$baudrate $othbootargs; " \ |
| 730 | "run norloadrecovery; " \ |
| 731 | "bootm $kerneladdr - $dtbaddr\0" \ |
| 732 | "norbootworking=setenv bootargs $workingbootargs" \ |
| 733 | " console=$consoledev,$baudrate $othbootargs; " \ |
| 734 | "run norloadworking; " \ |
| 735 | "bootm $kerneladdr - $dtbaddr\0" \ |
| 736 | "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ |
| 737 | "setenv cramfsaddr $nor_recoveryaddr; " \ |
| 738 | "cramfsload $dtbaddr $dtbfile; " \ |
| 739 | "cramfsload $kerneladdr $kernelfile\0" \ |
| 740 | "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ |
| 741 | "setenv cramfsaddr $nor_workingaddr; " \ |
| 742 | "cramfsload $dtbaddr $dtbfile; " \ |
| 743 | "cramfsload $kerneladdr $kernelfile\0" \ |
| 744 | "othbootargs=quiet\0" \ |
| 745 | "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ |
| 746 | " console=$consoledev,$baudrate $othbootargs; " \ |
| 747 | "tftp $rootfsaddr $rootfsfile; " \ |
| 748 | "tftp $loadaddr $kernelfile; " \ |
| 749 | "tftp $dtbaddr $dtbfile; " \ |
| 750 | "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ |
| 751 | "ramdisk_size=120000\0" \ |
| 752 | "ramdiskfile=rootfs.ext2.gz.uboot\0" \ |
| 753 | "recoveryaddr=0x02F00000\0" \ |
| 754 | "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ |
| 755 | "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ |
| 756 | "mw.l 0xffe0f008 0x00400000\0" \ |
| 757 | "rootfsaddr=0x02F00000\0" \ |
| 758 | "rootfsfile=rootfs.ext2.gz.uboot\0" \ |
| 759 | "rootpath=/opt/nfsroot\0" \ |
| 760 | "silent=1\0" \ |
| 761 | "tftpflash=tftpboot $loadaddr $uboot; " \ |
| 762 | "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| 763 | "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| 764 | "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ |
| 765 | "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| 766 | "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ |
| 767 | "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ |
| 768 | "ubootaddr=0x01000000\0" \ |
| 769 | "ubootfile=u-boot.bin\0" \ |
| 770 | "upgrade=run flashworking\0" \ |
| 771 | "workingaddr=0x02F00000\0" \ |
| 772 | "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" |
| 773 | |
| 774 | #else /* For Arcturus Modules */ |
| 775 | |
| Oleksandr G Zhadan | 8b0044f | 2015-04-29 16:57:39 -0400 | [diff] [blame] | 776 | #define CONFIG_EXTRA_ENV_SETTINGS \ |
| 777 | "bootcmd=run norkernel\0" \ |
| 778 | "bootfile=uImage\0" \ |
| 779 | "consoledev=ttyS0\0" \ |
| 780 | "dtbaddr=0x00c00000\0" \ |
| 781 | "dtbfile=image.dtb\0" \ |
| 782 | "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ |
| 783 | "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ |
| 784 | "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ |
| 785 | "fileaddr=0x01000000\0" \ |
| 786 | "filesize=0x00080000\0" \ |
| 787 | "flashmbr=sf probe 0; " \ |
| 788 | "tftp $loadaddr $mbr; " \ |
| 789 | "sf erase $mbr_offset +$filesize; " \ |
| 790 | "sf write $loadaddr $mbr_offset $filesize\0" \ |
| 791 | "flashuboot=tftp $loadaddr $ubootfile; " \ |
| 792 | "protect off $nor_ubootaddr0 +$filesize; " \ |
| 793 | "erase $nor_ubootaddr0 +$filesize; " \ |
| 794 | "cp.b $loadaddr $nor_ubootaddr0 $filesize; " \ |
| 795 | "protect on $nor_ubootaddr0 +$filesize; " \ |
| 796 | "protect off $nor_ubootaddr1 +$filesize; " \ |
| 797 | "erase $nor_ubootaddr1 +$filesize; " \ |
| 798 | "cp.b $loadaddr $nor_ubootaddr1 $filesize; " \ |
| 799 | "protect on $nor_ubootaddr1 +$filesize\0 " \ |
| 800 | "format0=protect off $part0base +$part0size; " \ |
| 801 | "erase $part0base +$part0size\0" \ |
| 802 | "format1=protect off $part1base +$part1size; " \ |
| 803 | "erase $part1base +$part1size\0" \ |
| 804 | "format2=protect off $part2base +$part2size; " \ |
| 805 | "erase $part2base +$part2size\0" \ |
| 806 | "format3=protect off $part3base +$part3size; " \ |
| 807 | "erase $part3base +$part3size\0" \ |
| 808 | "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ |
| 809 | "kerneladdr=0x01100000\0" \ |
| 810 | "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \ |
| 811 | "kernelfile=uImage\0" \ |
| 812 | "loadaddr=0x01000000\0" \ |
| 813 | "mbr=uCP1020.mbr\0" \ |
| 814 | "mbr_offset=0x00000000\0" \ |
| 815 | "netdev=eth0\0" \ |
| 816 | "nor_ubootaddr0=0xEC000000\0" \ |
| 817 | "nor_ubootaddr1=0xEFF80000\0" \ |
| 818 | "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \ |
| 819 | "run norkernelload; " \ |
| 820 | "bootm $kerneladdr - $dtbaddr\0" \ |
| 821 | "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \ |
| 822 | "setenv cramfsaddr $part0base; " \ |
| 823 | "cramfsload $dtbaddr $dtbfile; " \ |
| 824 | "cramfsload $kerneladdr $kernelfile\0" \ |
| 825 | "part0base=0xEC100000\0" \ |
| 826 | "part0size=0x00700000\0" \ |
| 827 | "part1base=0xEC800000\0" \ |
| 828 | "part1size=0x02000000\0" \ |
| 829 | "part2base=0xEE800000\0" \ |
| 830 | "part2size=0x00800000\0" \ |
| 831 | "part3base=0xEF000000\0" \ |
| 832 | "part3size=0x00F80000\0" \ |
| 833 | "partENVbase=0xEC080000\0" \ |
| 834 | "partENVsize=0x00080000\0" \ |
| 835 | "program0=tftp part0-000000.bin; " \ |
| 836 | "protect off $part0base +$filesize; " \ |
| 837 | "erase $part0base +$filesize; " \ |
| 838 | "cp.b $loadaddr $part0base $filesize; " \ |
| 839 | "echo Verifying...; " \ |
| 840 | "cmp.b $loadaddr $part0base $filesize\0" \ |
| 841 | "program1=tftp part1-000000.bin; " \ |
| 842 | "protect off $part1base +$filesize; " \ |
| 843 | "erase $part1base +$filesize; " \ |
| 844 | "cp.b $loadaddr $part1base $filesize; " \ |
| 845 | "echo Verifying...; " \ |
| 846 | "cmp.b $loadaddr $part1base $filesize\0" \ |
| 847 | "program2=tftp part2-000000.bin; " \ |
| 848 | "protect off $part2base +$filesize; " \ |
| 849 | "erase $part2base +$filesize; " \ |
| 850 | "cp.b $loadaddr $part2base $filesize; " \ |
| 851 | "echo Verifying...; " \ |
| 852 | "cmp.b $loadaddr $part2base $filesize\0" \ |
| 853 | "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ |
| 854 | " console=$consoledev,$baudrate $othbootargs; " \ |
| 855 | "tftp $rootfsaddr $rootfsfile; " \ |
| 856 | "tftp $loadaddr $kernelfile; " \ |
| 857 | "tftp $dtbaddr $dtbfile; " \ |
| 858 | "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ |
| 859 | "ramdisk_size=120000\0" \ |
| 860 | "ramdiskfile=rootfs.ext2.gz.uboot\0" \ |
| 861 | "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ |
| 862 | "mw.l 0xffe0f008 0x00400000\0" \ |
| 863 | "rootfsaddr=0x02F00000\0" \ |
| 864 | "rootfsfile=rootfs.ext2.gz.uboot\0" \ |
| 865 | "rootpath=/opt/nfsroot\0" \ |
| 866 | "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ |
| 867 | "sf probe 0; sf erase 0 +$filesize; " \ |
| 868 | "sf write $loadaddr 0 $filesize\0" \ |
| 869 | "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ |
| 870 | "protect off 0xeC000000 +$filesize; " \ |
| 871 | "erase 0xEC000000 +$filesize; " \ |
| 872 | "cp.b $loadaddr 0xEC000000 $filesize; " \ |
| 873 | "cmp.b $loadaddr 0xEC000000 $filesize; " \ |
| 874 | "protect on 0xeC000000 +$filesize\0" \ |
| 875 | "tftpflash=tftpboot $loadaddr $uboot; " \ |
| 876 | "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| 877 | "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| 878 | "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ |
| 879 | "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| 880 | "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ |
| 881 | "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ |
| 882 | "ubootfile=u-boot.bin\0" \ |
| 883 | "upgrade=run flashuboot\0" \ |
| 884 | "usb_phy_type=ulpi\0 " \ |
| 885 | "boot_nfs= " \ |
| 886 | "setenv bootargs root=/dev/nfs rw " \ |
| 887 | "nfsroot=$serverip:$rootpath " \ |
| 888 | "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| 889 | "console=$consoledev,$baudrate $othbootargs;" \ |
| 890 | "tftp $loadaddr $bootfile;" \ |
| 891 | "tftp $fdtaddr $fdtfile;" \ |
| 892 | "bootm $loadaddr - $fdtaddr\0" \ |
| 893 | "boot_hd = " \ |
| 894 | "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ |
| 895 | "console=$consoledev,$baudrate $othbootargs;" \ |
| 896 | "usb start;" \ |
| 897 | "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ |
| 898 | "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ |
| 899 | "bootm $loadaddr - $fdtaddr\0" \ |
| 900 | "boot_usb_fat = " \ |
| 901 | "setenv bootargs root=/dev/ram rw " \ |
| 902 | "console=$consoledev,$baudrate $othbootargs " \ |
| 903 | "ramdisk_size=$ramdisk_size;" \ |
| 904 | "usb start;" \ |
| 905 | "fatload usb 0:2 $loadaddr $bootfile;" \ |
| 906 | "fatload usb 0:2 $fdtaddr $fdtfile;" \ |
| 907 | "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ |
| 908 | "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ |
| 909 | "boot_usb_ext2 = " \ |
| 910 | "setenv bootargs root=/dev/ram rw " \ |
| 911 | "console=$consoledev,$baudrate $othbootargs " \ |
| 912 | "ramdisk_size=$ramdisk_size;" \ |
| 913 | "usb start;" \ |
| 914 | "ext2load usb 0:4 $loadaddr $bootfile;" \ |
| 915 | "ext2load usb 0:4 $fdtaddr $fdtfile;" \ |
| 916 | "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ |
| 917 | "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ |
| 918 | "boot_nor = " \ |
| 919 | "setenv bootargs root=/dev/$jffs2nor rw " \ |
| 920 | "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ |
| 921 | "bootm $norbootaddr - $norfdtaddr\0 " \ |
| 922 | "boot_ram = " \ |
| 923 | "setenv bootargs root=/dev/ram rw " \ |
| 924 | "console=$consoledev,$baudrate $othbootargs " \ |
| 925 | "ramdisk_size=$ramdisk_size;" \ |
| 926 | "tftp $ramdiskaddr $ramdiskfile;" \ |
| 927 | "tftp $loadaddr $bootfile;" \ |
| 928 | "tftp $fdtaddr $fdtfile;" \ |
| 929 | "bootm $loadaddr $ramdiskaddr $fdtaddr\0" |
| 930 | |
| 931 | #endif |
| 932 | #endif |
| 933 | |
| 934 | #endif /* __CONFIG_H */ |