Peng Fan | 86a1797 | 2022-07-26 16:41:10 +0800 | [diff] [blame] | 1 | // SPDX-License-Identifier: GPL-2.0+ |
| 2 | /* |
| 3 | * Copyright 2022 NXP |
| 4 | */ |
| 5 | |
| 6 | / { |
| 7 | wdt-reboot { |
| 8 | compatible = "wdt-reboot"; |
| 9 | wdt = <&wdog3>; |
| 10 | u-boot,dm-spl; |
| 11 | }; |
| 12 | |
| 13 | aliases { |
| 14 | usbgadget0 = &usbg1; |
| 15 | usbgadget1 = &usbg2; |
| 16 | }; |
| 17 | |
| 18 | usbg1: usbg1 { |
| 19 | compatible = "fsl,imx27-usb-gadget"; |
| 20 | dr_mode = "peripheral"; |
| 21 | chipidea,usb = <&usbotg1>; |
| 22 | status = "okay"; |
| 23 | }; |
| 24 | |
| 25 | usbg2: usbg2 { |
| 26 | compatible = "fsl,imx27-usb-gadget"; |
| 27 | dr_mode = "peripheral"; |
| 28 | chipidea,usb = <&usbotg2>; |
| 29 | status = "okay"; |
| 30 | }; |
| 31 | |
| 32 | firmware { |
| 33 | optee { |
| 34 | compatible = "linaro,optee-tz"; |
| 35 | method = "smc"; |
| 36 | }; |
| 37 | }; |
| 38 | }; |
| 39 | |
| 40 | &{/soc@0} { |
| 41 | u-boot,dm-pre-reloc; |
| 42 | u-boot,dm-spl; |
| 43 | }; |
| 44 | |
| 45 | &aips1 { |
| 46 | u-boot,dm-spl; |
| 47 | u-boot,dm-pre-reloc; |
| 48 | }; |
| 49 | |
| 50 | &aips2 { |
| 51 | u-boot,dm-spl; |
| 52 | }; |
| 53 | |
| 54 | &aips3 { |
| 55 | u-boot,dm-spl; |
| 56 | }; |
| 57 | |
| 58 | &iomuxc { |
| 59 | u-boot,dm-spl; |
| 60 | }; |
| 61 | |
| 62 | ®_usdhc2_vmmc { |
| 63 | u-boot,off-on-delay-us = <20000>; |
| 64 | u-boot,dm-spl; |
| 65 | }; |
| 66 | |
| 67 | &pinctrl_reg_usdhc2_vmmc { |
| 68 | u-boot,dm-spl; |
| 69 | }; |
| 70 | |
| 71 | &pinctrl_uart1 { |
| 72 | u-boot,dm-spl; |
| 73 | }; |
| 74 | |
| 75 | &pinctrl_usdhc2_gpio { |
| 76 | u-boot,dm-spl; |
| 77 | }; |
| 78 | |
| 79 | &pinctrl_usdhc2 { |
| 80 | u-boot,dm-spl; |
| 81 | }; |
| 82 | |
| 83 | &gpio1 { |
| 84 | u-boot,dm-spl; |
| 85 | }; |
| 86 | |
| 87 | &gpio2 { |
| 88 | u-boot,dm-spl; |
| 89 | }; |
| 90 | |
| 91 | &gpio3 { |
| 92 | u-boot,dm-spl; |
| 93 | }; |
| 94 | |
| 95 | &gpio4 { |
| 96 | u-boot,dm-spl; |
| 97 | }; |
| 98 | |
| 99 | &lpuart1 { |
| 100 | u-boot,dm-spl; |
| 101 | }; |
| 102 | |
| 103 | &usdhc1 { |
| 104 | u-boot,dm-spl; |
| 105 | }; |
| 106 | |
| 107 | &usdhc2 { |
| 108 | u-boot,dm-spl; |
| 109 | fsl,signal-voltage-switch-extra-delay-ms = <8>; |
| 110 | }; |
| 111 | |
| 112 | &lpi2c2 { |
| 113 | u-boot,dm-spl; |
| 114 | }; |
| 115 | |
| 116 | &{/soc@0/bus@44000000/i2c@44350000/pmic@25} { |
| 117 | u-boot,dm-spl; |
| 118 | }; |
| 119 | |
| 120 | &{/soc@0/bus@44000000/i2c@44350000/pmic@25/regulators} { |
| 121 | u-boot,dm-spl; |
| 122 | }; |
| 123 | |
| 124 | &pinctrl_lpi2c2 { |
| 125 | u-boot,dm-spl; |
| 126 | }; |
| 127 | |
| 128 | &fec { |
| 129 | phy-reset-gpios = <&pcal6524 16 GPIO_ACTIVE_LOW>; |
| 130 | phy-reset-duration = <15>; |
| 131 | phy-reset-post-delay = <100>; |
| 132 | }; |
| 133 | |
| 134 | &eqos { |
| 135 | compatible = "fsl,imx-eqos"; |
| 136 | }; |
| 137 | |
| 138 | ðphy1 { |
| 139 | reset-gpios = <&pcal6524 15 GPIO_ACTIVE_LOW>; |
| 140 | reset-assert-us = <15000>; |
| 141 | reset-deassert-us = <100000>; |
| 142 | }; |
| 143 | |
| 144 | &usbotg1 { |
| 145 | status = "okay"; |
| 146 | extcon = <&ptn5110>; |
| 147 | }; |
| 148 | |
| 149 | &usbotg2 { |
| 150 | status = "okay"; |
| 151 | extcon = <&ptn5110_2>; |
| 152 | }; |
| 153 | |
| 154 | &s4muap { |
| 155 | u-boot,dm-spl; |
| 156 | status = "okay"; |
| 157 | }; |