| Peng Fan | 0d331c0 | 2019-03-05 02:32:49 +0000 | [diff] [blame] | 1 | U-Boot for the NXP i.MX8QM EVK board |
| 2 | |
| 3 | Quick Start |
| 4 | =========== |
| 5 | |
| 6 | - Build the ARM Trusted firmware binary |
| 7 | - Get scfw_tcm.bin and ahab-container.img |
| 8 | - Build U-Boot |
| 9 | - Flash the binary into the SD card |
| 10 | - Boot |
| 11 | |
| 12 | Get and Build the ARM Trusted firmware |
| 13 | ====================================== |
| 14 | |
| 15 | $ git clone https://source.codeaurora.org/external/imx/imx-atf |
| 16 | $ cd imx-atf/ |
| 17 | $ git checkout origin/imx_4.14.78_1.0.0_ga -b imx_4.14.78_1.0.0_ga |
| 18 | $ make PLAT=imx8qm bl31 |
| 19 | |
| 20 | Get scfw_tcm.bin and ahab-container.img |
| 21 | ============================== |
| 22 | |
| 23 | $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-sc-firmware-1.1.bin |
| 24 | $ chmod +x imx-sc-firmware-1.1.bin |
| 25 | $ ./imx-sc-firmware-1.1.bin |
| 26 | $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin |
| 27 | $ chmod +x firmware-imx-8.0.bin |
| 28 | $ ./firmware-imx-8.0.bin |
| 29 | |
| 30 | Copy the following binaries to U-Boot folder: |
| 31 | |
| 32 | $ cp imx-atf/build/imx8qm/release/bl31.bin . |
| 33 | $ cp u-boot/u-boot.bin . |
| 34 | |
| 35 | Copy the following firmwares U-Boot folder : |
| 36 | |
| 37 | $ cp firmware-imx-7.6/firmware/seco/ahab-container.img . |
| 38 | $ cp imx-sc-firmware-0.7/mx8qm-mek-scfw-tcm.bin . |
| 39 | |
| 40 | Build U-Boot |
| 41 | ============ |
| Peng Fan | 0d331c0 | 2019-03-05 02:32:49 +0000 | [diff] [blame] | 42 | $ make imx8qm_mek_defconfig |
| 43 | $ make flash.bin |
| Peng Fan | 0d331c0 | 2019-03-05 02:32:49 +0000 | [diff] [blame] | 44 | |
| 45 | Flash the binary into the SD card |
| 46 | ================================= |
| 47 | |
| 48 | Burn the flash.bin binary to SD card offset 32KB: |
| 49 | |
| 50 | $ sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32 |
| 51 | |
| 52 | Boot |
| 53 | ==== |
| 54 | Set Boot switch SW2: 1100. |