| Masahiro Yamada | da333ae | 2014-10-23 22:26:09 +0900 | [diff] [blame] | 1 | config DM_SPI |
| 2 | bool "Enable Driver Model for SPI drivers" |
| 3 | depends on DM |
| 4 | help |
| Simon Glass | f94a1be | 2015-02-05 21:41:35 -0700 | [diff] [blame] | 5 | Enable driver model for SPI. The SPI slave interface |
| 6 | (spi_setup_slave(), spi_xfer(), etc.) is then implemented by |
| 7 | the SPI uclass. Drivers provide methods to access the SPI |
| 8 | buses that they control. The uclass interface is defined in |
| 9 | include/spi.h. The existing spi_slave structure is attached |
| 10 | as 'parent data' to every slave on each bus. Slaves |
| 11 | typically use driver-private data instead of extending the |
| 12 | spi_slave structure. |
| Simon Glass | 892cac7 | 2015-03-06 13:19:05 -0700 | [diff] [blame] | 13 | |
| 14 | config SANDBOX_SPI |
| 15 | bool "Sandbox SPI driver" |
| 16 | depends on SANDBOX && DM |
| 17 | help |
| 18 | Enable SPI support for sandbox. This is an emulation of a real SPI |
| 19 | bus. Devices can be attached to the bus using the device tree |
| 20 | which specifies the driver to use. As an example, see this device |
| 21 | tree fragment from sandbox.dts. It shows that the SPI bus has a |
| 22 | single flash device on chip select 0 which is emulated by the driver |
| 23 | for "sandbox,spi-flash", which is in drivers/mtd/spi/sandbox.c. |
| 24 | |
| 25 | spi@0 { |
| 26 | #address-cells = <1>; |
| 27 | #size-cells = <0>; |
| 28 | reg = <0>; |
| 29 | compatible = "sandbox,spi"; |
| 30 | cs-gpios = <0>, <&gpio_a 0>; |
| 31 | flash@0 { |
| 32 | reg = <0>; |
| 33 | compatible = "spansion,m25p16", "sandbox,spi-flash"; |
| 34 | spi-max-frequency = <40000000>; |
| 35 | sandbox,filename = "spi.bin"; |
| 36 | }; |
| 37 | }; |
| Marek Vasut | 67d7a9d | 2015-03-04 23:12:45 +0100 | [diff] [blame] | 38 | |
| 39 | config DESIGNWARE_SPI |
| 40 | bool "Designware SPI driver" |
| 41 | depends on DM_SPI |
| 42 | help |
| 43 | Enable the Designware SPI driver. This driver can be used to |
| 44 | access the SPI NOR flash on platforms embedding this Designware |
| 45 | IP core. |
| Marek Vasut | 96bfdf0 | 2015-03-04 23:13:48 +0100 | [diff] [blame] | 46 | |
| 47 | config CADENCE_QSPI |
| 48 | bool "Cadence QSPI driver" |
| 49 | depends on DM_SPI |
| 50 | help |
| 51 | Enable the Cadence Quad-SPI (QSPI) driver. This driver can be |
| 52 | used to access the SPI NOR flash on platforms embedding this |
| 53 | Cadence IP core. |
| Jagan Teki | df30a42 | 2015-06-27 00:51:38 +0530 | [diff] [blame^] | 54 | |
| 55 | config ZYNQ_SPI |
| 56 | bool "Zynq SPI driver" |
| 57 | depends on DM_SPI && (ARCH_ZYNQ || TARGET_XILINX_ZYNQMP) |
| 58 | help |
| 59 | Enable the Zynq SPI driver. This driver can be used to |
| 60 | access the SPI NOR flash on platforms embedding this Zynq |
| 61 | SPI IP core. |